Tender For Special Repairs To Bldg No T-26 (Mt Pl) In ‘C’ Zone, Provn Of Security Gate For Unit Kote At Bldg No T-94 In ‘C’ Zone And Provn Of Washing Point Near Mt Shed In ‘C’ Zone At Rms.; 1 Demolition of cement concrete (unreinforced) in ground floors and paving n.exc. 15cm thick (below or above ground level) and removal of rubbish from the site complete all as specified and as directed. 2 Demolition oftiles of any description or thickness in floors, aprons etc laid, bedded and pointed in mortar complete all as specified and directed. 3 M&L for second class hardwood as in scantlings clean sawn timberfixed with and including dismantling of old timber scantlings 40 sqcm and over in section, in unframed work in any position complete all as specified and as directed. 4 M & L for plain fillets, square, rectangular or triangular in section clean sawn, secured with nails made out of 2nd class hard wood exc 13and n.exc 25 sqcm complete all as specified and as directed. 5 Demolition of brick work or stone/boulder masonry, built in cement mortar including all quions, arches, pillars ,etc complete all as specified and as directed. 6 M&L for brick work with sub class B bricks (using old size burnt bricks) straight or curved on plan exc 6m mean radius in half brick thick wall built in cement mortar (1:4) complete all as specified and as directed. 7 S&FPre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of old corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed. 8 S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of old corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed. 9 M&L for 15mm thick plastering in CM (1:4) on one side of lathing in two separate layers without using extra cement but using water proofing compound @ 3% by wt of cement for finished even and smooth including demolition of reed, lathing single or double, including battens and plaster or chicken wire lathing with and including GI wire netting 0.71 mm dia and 12 mm mesh lathing in to reed in walls incl all laps cutting and waste complete all as specified and as directed.Note:-WPC will be measured and paid separately. 10 M&L for rendering 12 mm thick in CM (1:6) on other side of lathing finished even and smooth without using extra cement complete all as specified and as directed. 11 S&F for joist, channels, angles, or tee sections, fixed independently, without connecting plates, etc, (cut to ordinary lenght i.e. Within 20mm of the lenght indicated conforming Fe-410-W (Gde E-250 quality -A) complete all as specified and directed by Engr-in-charge.. 12 S&F MS plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming Fe 410 -W (Gde- E- 250) quality- A complete all as specified and as directed. 13 M & L for 15 mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and as directed. 14 M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm,in floors laid over and including 15mm thick screed bed or bedding layer of cement mortar (1:6) for laying floor finishes, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed. 15 All per item No 14.00 (here-in-before) but on vertical surfaces such as skirting , dado risers to stepsover and including 10 mm thick backing coat in CM (1:4). 16 M & L for coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular),area of each tiles exceeding0.06 sqm but not exceeding 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in whitecement mixed with pigment to match shade of tiles,laid over and including 15 mm thick screed bed in CM (1:6)complete all as specified and directed. 17 M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile, over and including 10mm thick CM (1:4) backing coatcomplete all as specified and directed. 18 M & L for PCC, 25 mm thick type B-0, (1:2:4) (using 12.5 mm graded stone aggregate)as in levelling course of floor complete all as specified and as directed. 19 M&L for 100 mm thick PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in floor, finished even and smooth with out using extra cement complete all as specified and as directed. 20 M&L for 75 mm thick PCC (1:3:6) type C2 , using 40 mm graded stone agg in plinth protection/hardstanding laid to slope of 1:12, finished fair and even without using extra cement with and including all necessary formwork to divide tha area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 10 mm wide joints throughout thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified and directed 21 S & F for4 mm thick of size 600x600mmHSPC (high pressure Steam Cured) pre-Painted self embossed, textured designer boardE-Board Classic to be fixed Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. fixed in ceiling flat or Slopingincluding dismantling of old unsv ceiling boards (fibre, pulp, insulation, etc.) any thickness including cover fillets of any description and at any location complete all as specified and as directed. 22 Taking down chowkhat or frames not exc 1.5 Sqm each (without taking off shutter from the frame) complete all as specifed and directed. 23 Taking down chowkhat or frameexc 1.5 sqm not exc 4 sqm each (without taking off shutters from the frame) complete all as specifed and directed. 24 S&FPlain, solid straight chowkat and frames, wrought, frmedrebated on the solid, rounded or chamfred put together with glue pinned at joints , supplied and fixed in 2nd class hard wood etc complete all as specified and directed. 25 S&F 35 mm thick factory made flush shutter, solid core construction, with particle board core and plywood face panels, commercial type on both side fixed to chowkats complete all as specified and directed. 26 M&L for 30mm thick 2nd class hard woodGlazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(a) complete all as specified and as directed. 27 S&F in repair mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 18mm, fixed with tinned tacks or galvanized wire staples complete all as specified and as directed. 28 S&F anodised aluminium powder coated any colour frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing complete all as specified and as directed. 29 S & F for Anodised aluminium Window and ventilator shutters, without sash bars, aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws complete all as specified and as directed. 30 S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed. 31 S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification complete all as specified and as directed. 32 S&F Factory made solid panel pvc doorshutter 30 mm thick (style) con-sisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be cov-ered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement suppling & fixing at site as per specification complete all as specified and as directed. 33 S&F butt hinges medium grade cold rolled mild steel and fixed size of hinges 100 mm long size complete all as specified and as directed. 34 S&F Aluminium anodised barrel tower bolt of extruded section and fixed 100 mm long complete all as specified and as directed. 35 S&F Aluminium handle cast type anodised 150 mm long complete all as specified and as directed. 36 S&F Aluminium alloy anodised sliding door bolt with hasp and staple (bolt type fixing clips of sheet cast or extruxded section(300 mm long) complete all as specified and as directed. 37 S&F in repair 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed. 38 S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc .50 sqm in each panels complete all as specified and as directed. 39 M & L for rendering 15 mm thick in cement mortar (1:6) on fair faces of brick or concrete work even and smooth without using extra cement complete all as specified and as directed. 40 M & L forrendering 15 mm thick in cement mortar (1:4) on fair faces of brick or concrete work even and smooth without using extra cement complete all as specified and as directed. 41 M&L for applying two coats of oil bound distemper over a coat of primer over a coat of 2 mm thick wall care putty(in two layers) on new plastered surfaces of walls including preparation of newsurface complete all as specified and as directed. 42 M&L for preparation of new plastered surfaces and applying two coats ofcement base paint over a coat of primer of approved shade on wallscomplete all as specified and as directed. 43 M&L for complete removal of existing treatment and applying two coats of distemper oil emulsiion over a coat of primer onold treated plastered surface of wall complete all as specified and as directed. 44 M&L for complete removal of existing treatment and applying two coats of cement based paint over a coat of primer on old treated plastered surface of wall complete all as specified and as directed. 45 M&L for preparation of old painted wood and wood based surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint in any tint complete all as specified and as directed. 46 M&L for preparation of new untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink wood primer complete all as specified and as directed. 47 M&L for preparation of newsurfaces of steel and iron work of any description over 10 cm width or girth not otherwise described andapplying two coats of synthetic enamel paint over a coat of redoxide on new surfaces in any tint complete all as specified. 48 M&L for preparation of old surfaces of steel and iron work of any description over 10 cm width or girth not otherwise described andapplying one coat of synthetic enamel paintin any tint complete all as specified and as directed. 49 S&F in repairs 15mm bore GI water tubing medium grade laid in floors or fixed in wall including GIfittings complete all as specified and as directed. 50 S&F 15mm bore GI water tubing medium grade laid in floors or fixed in wall including GIfittings complete all as specified and as directed. 51 All as per Ser item No.49.00 but fixing only. 52 S&F in repairs 20 mm bore GI water tubing medium grade laid in floors or fixed in wall including GIfittings complete all as specified and as directed. 53 S&F 20 mm bore GI water tubing medium grade laid in floors or fixed in wall including GIfittings complete all as specified and as directed. 54 All as per Ser item No.52.00 but fixing only. 55 M&L for Cement Concrete (1:4:8), Type D-2, (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed. 56 Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in hard dence soil complete all as specified and as directed. 57 S & F Fe 410 w (Gde E -250 quality only) Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed. 58 S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long n exc 10 cm -11 to 15 mm dia of neck complete all as specified and as directed. 59 S&F Steel ventilator with top hung shutter including hinges, steel pegstay,complete all as specified and as directed. 60 S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed. 61 Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in soft/ loose soil complete all as specified and as directed. 62 Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth; for foundation etc or for shafts, wells, cesspits, manhole, pier holes, etc n.exc 10 Sqm on plan andn.exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and as directed. 63 M&L for mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. 64 Removing excavation material n exc. 50m & deposited where directed at a level n exc. 1.5m above the starting point complete all as specified and as directed. 65 Returning, filling in, including spreading, leveling, watering & well ramming in layer s not exc 25 cm complete all as specified and as directed. 66 M&L for hardcore of gauge n.exc 63mm, deposited, spread and levelled in layers n.exc 15cm thick, watered and rammmed to a true surface complete all as specified and as directed. 67 M&L for PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in cills, copings, benching on chajjas, roof kerbs, bed blocks and the like including weathering, slightly rounded or chamfered angles and throating as directed with and including necessary form work complete all as specified and directed. 68 M&L for PCC (1:2:4) type B-2 (using 40mm graded crushed stone aggregate) for Ramps, roof kerb or mud stops, rounded or chamfered on edges including finishing surface of concrete ramp by brooming complete all as specified and directed. 69 S&F20 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed. 70 M&L for RCC (Nominal Mix) (1:1.5:3) type A-1 (using 20mm graded stone aggregate) slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. 71 Use and waste of formwork to sides and soffits of floors or roof beams, beams haunchings, girders,bressummers lintels, cantilevers, shelves including supports overhangs etc also splays between floors and beams complete all as specified and as directed. 72 M&L of sand filling under floor well ramming including watering as required Spreading & leveling in layers n.exc. 25cm thick complete all as specified and as directed. 73 S&F PVC valveless, syphonic action type, flushing cistern, low level,white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed. 74 S&FVitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) and including EWC Seat cover complete all as specified and as directed. 75 Supply only flush pipe of polyethylene of low or high density of PVC 32mm dia for low level cistern complete all as specified and as directed. 76 S&F in repairs CP Health Faucet with 1 mtr metalic Expandable tube & hook complete all as specified and as directed. 77 S& Fcast iron P or S trap of 100mm diacomplete all as specified and as directed. 78 S&F in repairs for 15mm dia of pipe bib taps cast copper alloy, fancy type, chromium plated with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed. 79 S&F in repairs Stainless steel soap dish white of size 160 x 160 x 90 mm as approved fixed with brass screws or embedded in wall completeall as specified and as directed. 80 S&F in repairs 600mm long tubular tower rail brass chromium plated 20mm dia, D type ,fixedwith two plugs (Gutties) of 2nd class hard wood embeded in cement mortor 1:3 with MS screws completeall as specified and as directed. 81 S& F in repairs 600 mm x 450 mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick AC building board or commerical plywood and fixed to wooden plugs with chromium plated brass screws and cup washers fancy type complete all as specified and as directed. 82 S&F in repairs CP toilet paper holdercomplete all as specified and as directed. 83 S&F in repairs corner glass shelf assembly 250mm radius made of 6mm thick craaylic glass, with CP railing, fixed with suitable rowal plug & screws complete all as specified and directed. 84 S&F in repairs vitreous china fancy wash basin, size 550 x 400mm white including brackets, and waste coupling & pipe of 32mm dia, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed complete all as specified and as directed. 85 S&F of PVC (SWR) 110 mm dia pipe as per specification complete all as specified and as directed. 86 S & FPVC (SWR) Bend with any radius of 110 mm diacomplete all as specified and as directed. 87 S&F of PVC (SWR) 75 mm dia pipe as per specification complete all as specified and as directed. 88 S & FPVC (SWR) Bend with access door any radius of 75 mm diacomplete all as specified and as directed. 89 M&L for cement concrete type B-1 (1:2:4) (using 20 mm graded stone aggregate) as in surface channels and drains complete all as specified and as directed. 90 M & L for PCC (1:4:8) type D-2, 100 mm thick (using 40 mm graded stone aggregate) as in hardstanding complete all as specified and as directed. 91 M&L for chequered cement concrete tiles of size not less than 300x300x25mm thick laid over and including 15mm thick screed bedfor laying floor finishes in cement mortar (1:6), etc, set, jointed and pointed in neat cement slurry with grey cement and pigmentscomplete all as specified and as directed. 92 M&L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement incl firms moulds complete all as specified and as directed. 93 M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe 410 -W (Gde-E- 250) quality-Acomplete all as specified and as directed. 94 M&L for vitreous china squatting pan, Orissa, pattern size 580 x 440 mm white with integral foot rests(excluding flushing cistern and flush pipe)including connection to trap and to flushing pipe, anti-syphonage pipe etc complete including making good to floor complete all as specified and as directed. 95 S&Fsteelworkintubulartrusses, post, purlinsincludingspecialshapedwasheretc.CompleteusingERWorinductionbuttweldedtubesconformingtoIS1161-1979gradest-240complete all as specified and as directed. 96 S&F in repairsfor Draperly rod /Harrison rails of CP of 20mm dia with fixing brackets , stops, rollers and ringscomplete all as specified and as directed. 97 M&L for disconnecting existing tanks capacity exc 500 Ltr & n exc 1000 Ltr, setting asidee (or lowering if required) for repairs, cleaning, etc. and hositing if required reconnecting and re-fixing in position complete all as specified and as directed. 98 S&F in repairs rotational moulded polyethylene 1000 Ltrs Capacity water storage tanksdouble layer (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including ball brass valve, with polythelene float and fly nut complete screwed down for iron pipe of 20 mm dia complete all as specified and as directed. 99 S&F rotational moulded polyethylene 500 Ltrs Capacity water storage tanksdouble layer (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including ball brass valve, with polythelene float and fly nut complete screwed down for iron pipe of 20 mm dia complete all as specified and as directed. 100 M&L for brick work with sub class B bricks(using old size burnt bricks) straight or curved on plan exc 6 m mean radius in CM (1:4)complete all as specified and as directed. 101 Supply only Integralwater proofing compound complete all as specified and as directed. 102 M&L for Granite 20mm thick (of any type) as in platform thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigmentto match the shade of granite stone including grinding and polishing with nosing over and including 10 mm screed bed in CM (1:4) complete all as specified and as directed. 103 S&F aluminium anodised grill with mesh size 75 mm and aluminium bar 6 mm XPM type including all accessories such as channels for fixing grill screws etc, aluminium section 15 micron thick anodizing complete all as specified and directed. 104 M&L for Point wiring in repairs complete with two runs of 1.5 sqmm single core PVC insulated FR-LSH cable1100 volts grade with multi-stranded copper conductors, drawn throughand including PVC double locked Casing & caping including provision of 1.5 sqmm, FR-LSH, PVC insulated copper cable as earth continuity conductor connected to common earth dolly, including PVC rectagular box for mounting switches / sockets / regulators etc.of suitable size as required at site and 50 mm deep complete all as specified and as directed. 105 Onelight pointcontrolled by one, one way switch . 106 One Exh/Ceiling fan point controlled by one, one wayswitch. 107 One 3 pin socket outlet 5 Amps on the same board with other switches. 108 One 3 pin socket outlet 5 Amps on the Independent board. 109 All as per item No-104.00 here-in-before but with 2.5 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board and 2.5 Sq mm copper conductor green in colour as earth continuity conductor connected to common earth dolly complete all as specified and as directed. 110 S&F Switch piano flush type single pole, one way 5A complete all as specified and as directed. 111 S&FSocket outlet, 2 in 1, 3 pin 5A flush type complete all as specified and as directed. 112 S&FSwitch Socket combination, 2 in 1, 5 pin 5A flush type complete all as specified and as directed. 113 S&FSwitch socket combination 2 in 1, 5A/16A, 5 in 1 flush typecomplete all as specified and as directed. 114 S&Fstepped type electronic fan regulator 100/120 Watt socket size flush type on the existing phenolic laminated sheet complete all as specified and as directed. 115 S&Fceiling rose 3 terminal PVC/Polycarbonate isolated body complete all as specified and as directed. 116 M&L for sub main wiring Casing capingtwo run 4.0 Sq mm and one run of 4.0 Sq mm for earth wire with multi standard copper conductors, 1100 volts grade, drawn throughand including PVC casing caping complete all as specified and as directed. NOTE:- Two runs of 4.0 Sq mm +one run of 4.0 Sq mm and one run of PVC casing caping and its accessories of suitable size shall be measured as one unit length incl taking down old unsv complete all as specified and as directed. 117 S&F in repairs LED Light fitting 1 x 20 watt (4 Ft), Wall/ Surface mounted, intergrated type with all accessories internally prewired and incl connecting up with, including two Nos PVC blocks and connecting upwith flexible copper cableflexible pipe from ceiling rose to the light fitting complete all as specified and as directed. 118 S&F in repairs LED Light fitting 1 x 10 watt (2 Ft), Wall/ Surface mounted, intergrated type with all accessories internally prewired and incl connecting up with, including two Nos PVC blocks and connecting upwith flexible copper cableflexible pipe from ceiling rose to the light fittingcomplete all as specified and as directed. 119 S&F in repairs and testing in replacement of LED Bldg Security light fitting of capacity 25 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete including 1.2 mtr GI bracket of 25mm bore light grade bent to shape and fixed on wall with metal fastners 2 Nos 10mm dia incl drilling of holes as reqd and connecting up with flexible copper cable of size 0.75 sqmm 3 core from ceiling rose to the light fitting and all as specified and directed by Engr-in-Charge. 120 S&F in repairsLED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling and connecting up with driver, three core flexible copper conductor of suitable size complete all as specified and as directed. 121 M&L for overhauling/ servicing of ceiling fan of any size / sweep (i.e 1200/1400mm sweep) and make comprising dismantaling, cleaning internally and externally and cleaning / lubricating of bearing / bushes using fresh lubricant (Oil grease) re-assembling, checking of split pin, hook assembly & hanging andincluding provision of cable fromceiling rose or connector to fan and testing for proper functioning complete all as specified and directed. 122 Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed. 123 S&F in repairs MCB Distribution board double door type SPN 12 way, sheet steel, powder painted, with copper bus bar neutral link & earth bar etc. and fixing MCBs of various rating capacity complete all as specified and as directed. 124 S&F in repairs MCB Distribution board double door type SPN 8 way, sheet steel, powder painted, with copper bus bar neutral link & earth bar etc. and fixing MCBs of various rating capacity complete all as specified and as directed. 125 S&F MCB Distribution board single door type SPN 2 way, sheet steel, powder painted, withneutral link & earth bar etc. and fixing MCBs of various rating capacity complete all as specified and as directed.Make : Legrand Cat Part No 507611/ABB/Siemens 126 S&F in repairsMCB SPN 40-63 amp rating 240V, 10KA C curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed. Make : Legrand Cat Part No 408618/ABB/Siemens 127 S&F in repairs MCB SPN 32 amp rating 240V, 10KA C curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioningcomplete all as specified and as directed. Make : Legrand Cat Part No 408618/ABB/Siemens 128 S&F in repairs MCB SP 5-40 amp rating 240V, 10KA C curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed.Make:- Legrand Cat No 408587-95 /ABB/Siemens 129 M&L for laying of LT UG cable, XLPE insulated, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of 16 sq mm, 2 core including taking up old unsv cable complete all as specified and as directed. NOTE :- (i) Excavation and earth work, sand cushioning, cable protection cover, pipe etc. shall be measured and paid separately under relevant items. 130 M&L for laying of LT UG cable, XLPE insulated, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of 6 sq mm, 2 core complete all as specified and as directed. NOTE :- (i) Excavation and earth work, sand cushioning, cable protection cover, pipe etc. shall be measured and paid separately under relevant items.Make : Richa/Finolex/Polycab 131 M&L for spread fine river sand in trenches complete all as specified and as directed. NOTE: For measurement purpose, punned down thickness shall only be measured and paid. 132 M&L for laying brick sub class B old size burnt bricks for cable protection of size 230mmx115mmx75mm complete all as specified and as directed. 133 Supply & laying tubes Light grade galvanised, with all fittings, fixed complete to walls, poles, ceilings or laid in floors/ trenches/ road crossing for protection of cables of size 25 mm dia bore complete all as specified and as directed. 134 Supply & laying tubes light grade galvanised, with all fittings, fixed complete to walls, poles, ceilings for protection of cables of size 40 mm dia bore including taking out unsv GI tubing complete all as specified and as directed. 135 M&L for earthing complete with galvanized steel earth plate electrode of size 600x600x6mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4 mm dia as earth lead connectd by means of bolts, nuts, washers and check nuts all as shown in electrical plate No 3 of MES SSR Part-I, including testing on completion complete all as specified and as directed. NOTE:- (i)The unit rate shall also included for earth work in hard/ dense soil, PCC (1:3:6) type C1 chamber, CI frame with CI coverfunnel with GI watering pipe 20mm dia Medium grade, GI protection pipe light grade 15mm dia and wire mesh complete in addition to item No 1 (a) to (e) of preamble (notes) under sub heading earthing, specified on Sl Page No 441 of MES SSRPart-II. (ii)Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately.
