Tender For Additional / Alternator / Improvement To Certain Married Accommodation At Afs Amla; 1 M&L for Joint free, Non - skid coloured ceramic tiles; 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match set,over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed. 2 M&L for digital coloured glazed ceramic tiles in vertical surfaces 350 x 250 x 7mm/ 450 x 300 x7 to 8 mm thick, etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles including 10mm thick backing coat in 1:4 cement mortar complete all as specified and directed. 3 M&L for Non - skid coloured ceramic tiles; 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match in coloured cement to match the light shade of tiles over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed. 4 Ditto all as per item No 03 above but in vertical surfaces as in skirtings, set and jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over and including 10mm thick rendering or backing coat in cement mortar 1:3 complete all as specified and directed. 5 M&L for yellow/ Red colour pre-polished rubber moulded chequred cement concrete tile 300mm x 300mm x 20-22mm thick with anti skid properties set, jointed and pointed in neat cement slurry as in floor with grey cement and pigmentlaid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and as directed. 6 M&L for machine cut kota stone slab 20-25 mm thick (size of each stone not less than 55cm x 55cm), laid in flooring, over and including cement screed bed 20mm thick in cement mortar (1:6) base set and jointed in neat cement slurry @ 3.00 kg/Sqm and pointed in white or coloured cement to match the surface mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing (Mirror finish), cutting design for ahesthetic look complete all as specified and directed. 7 M&L for machine cut kota stone slab 20-25mm thick (size of each stonein single piece, laid on vertical surfaces of skirting/dado, over and including 15 mm thick rendering in cement mortar (1:4) and set and jointed in neat cement slurry @ 3.00 kg/Sqm and pointed in white or coloured cement to match the surface mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing (Mirror finish) complete all as specified and directed. 8 M&L for Machine cut cudappah stone slab 20-25mm thick for partition, slabs, shelves to be fixed with cement screed base including grouting with bick or concrete surface/wall and laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, partition etc including rubbing and polishing complete all as specified and directed 9 Demolition of stone slabs and tiles of any description or thickness laid, bedded and pointed in any mortar in floors, aprons etc complete all as specified and directed. 10 M&L for Granite (Z Black) 18 to 20 mm thick table rubbed & polished in steps , jambs, cills, shelves, chowkat etc including cutting of holes for fixing WHB in cement mortar 1:4 & pointing with white cement with marble dust using admixture of pigment to match with the shade of granite over and including 15mm thick screed in CM 1:4, moulding the corner of slabcomplete all as specified and as directed . 11 M&L for 40 mm thick Plain Cement Concrete 1:2:4 type B-0 using 12.50mm graded stone aggregate as in sub-floors, sub-bases, floor, etc., surface finished even and fair without using extra cement, including necessary form work complete all as specified and directed. 12 Taking down PVC chowkats or frames with shuttersnot exceeding 1.5 Sqm each(without taking off shutter from the frame) complete all as specifieddirected. 13 S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed. 14 S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with wood free EPS, with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm thick moulded prelam PVC sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed. 15 Taking down chowkats or frames with shutters any type not exceeding 1.5 Sqm each(without taking off shutter from the frame) complete all as specified anddirected. 16 Taking down chowkats or frames with shutters any type exceeding 1.5 Sqm and not exceeding 4.0 Sqm each (without taking off shutter from the frame) complete all as specified and directed. 17 S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat (for cupboard) of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp-ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length including M.S. hold fast/ lugs or SS dash fasteners including all fittings complete all as specified and directed.Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 18 S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat (for doors with one or more rebates) of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp-ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length including M.S. hold fast/ lugs or SS dash fasteners and necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed.Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 19 S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat (for doors with one or more rebates) of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp-ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length including M.S. hold fast/ lugs or SS dash fasteners and necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed.Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 20 S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain shutter of 20mm size for cupboard and shelf comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws for fixing including all fittings such as handle, tower bolt hasp staple, hinges etc complete all as specified and directed. 21 S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain shutter of 30mm size for door comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws for fixing including all fittings such as handle, tower bolt hasp staple, hinges etc complete all as specified and directed. 22 S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain shutter of 30mm size for glazed and skelton shutters, open rebated and prepared to receive glass, gauze etc, but divided in to square with plain, chamfered or rounded, mitred and rebated sash bar, any number fitted with cut and mitred beads for securing glass etc comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws for fixing including all fittings such as handle, tower bolt hasp staple, hinges, SS wire mesh etc complete all as specified and directed. 23 S&F in Repair Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and directe. 24 S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free,traight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws complete all as specified and directed. 25 S&F Powder coated aluminium Anodised aluminium grill (Dyed to required shade according to IS : 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P brass/stainless steel screws @200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified and directed 26 S&F 4.80 mm thick sheet glass selected quality and glazing in squares not exceeding 0.50 sqm in each pane of aluminium door / window complete all as specified and directed. 27 S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed. 28 S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor,Overall length of cover plate 150mm complete all as specified and directed. 29 S&F 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed. 30 S&F in repairs decorative mild steel coloured curtainrod of 20 mm dia powder coated approved pattern & design including side cups & powder coated mild steel flat iron brackets fixed with steel screws & PVC rawl plugs complete all as specified and directed. 31 S&F in repair Vitreous china squatting pan, Orissa pattern, size 580 x 440mm white, with integral foot rests (excluding flushing cistern) including connection to trap, flushing pipe to squatting pan, anti-syphonage pipe, etc., and making good to floor complete all as specified and directed. 32 S&F PVC(SWR) 110mm dia S trap including connecting to out let with solvent cement complete all as specified and directed. 33 M & L in repairs for PVC (SWR) nahani trap, plain with grating suitable for 75mm dia outlet pipe including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) with solvent cement complete all as specified and directed. 34 S&F in repair10 litre capacity PVC valveless syphonic action type flushing cistern, low level, white, with inlet, ball valve, float and handle including bracketsand flush pipe complete all as specified and directed. 35 S&F in repairs PVC connections 15mm size with PTMT nuts of length 450mm fixed to pipes and valves complete all as specified and directed. 36 S&F vitreous china wash hand basin white angle back size400mmx400mm excluding taps waste chain and plug and percelain stopper including two coats of synthetic enamel paint over coat of red oxide primer on exposed surfaces of brecketswaste coupling brass CP 32 mm bore with long screwed shanksbedded in red lead cement and other end fixed and pillar taps 15 mm bore cast copper alloy fancy type chromium plated screwed down high pressure withlong screwed shanks screwedand removing debris out of MoD land complete all as specified and directed. 37 S&F in repairs 15 mm bore bib taps cast copper alloy with Chromium platedcrutch or butterfly handle scrwed, screwed for iron pipe or for brass ferruleand fixed complete all as specified and directed. 38 S & F in repair 15mm bore stop valvesfancy type, chromium plated screwed down,high pressure,with crutch or butterfly handle,screwed both ends for iron pipe or for unions fixed complete all as specified and directed. 39 S&F 15mm bore brass chromium plated wall mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed. 40 S&F stainless steel plate rack of size approved pattern and size 0.90 x 0.60m and thickness of sheet 1mm complete all as specified and directed. 41 S&F in repairs 600mmx450mm bevelled edge mirror of selected quality glass mounted on 6mm thick AC building board or commercial plywood and fixed on the wall using wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed 42 S&F Soap dish, stainless steel, approximate size 160 x 160 x 90mm, fixed to plugs with chromium plated brass screws complete all as specified and directed. 43 S&F Stainless steel tubular towel rail, 20mm dia, D type, 60cm long between flanges fixed on the wall using wooden plugs with chromium-plated brass screws and cup washers complete all as specified and directed. 44 S&FStainless steel Towel Ring (Minimum 90 gms), Chromium plated brass screws and wooden/plastic cleats complete all as specified and directed. 45 S&F straight glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 Cm wide with chromium plated bracket guard and railing 60 Cm long complete all as specified and directed. 46 S & F Glass corner shelf fancy type of size 250x250 in 5.5-10mm thick fixed its brass bracket and screwed complete all as specified and as directed. 47 S&F in repairs Brass chromium plated shower rose 150mm size with or without swivel joints,including fixing to steel pipe or union complete all as specified and directed. 48 Taking up or down 15mm dia bore GI tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed. 49 Taking up or down 20mm dia bore GI tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed. 50 S&F 15mm dia bore GI tubing medium grade, galvanised with all fittings fixed to wall and ceiling or laid in floorscomplete all as specified and directed. 51 S&F 20mm dia bore GI tubing medium grade, galvanised with all fittings fixed to wall and ceiling or laid in floorscomplete all as specified and directed. 52 S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. 53 S&F 100mm dia grating doom of stainless steel (Minimum weight 25gms) complete all as specified and directed. 54 S&F 40mm unplasticiscd PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceiling or in floorsincluding all fittings like bend, T, elbow etc complete all as specified and as directed 55 Taking down CI/AC/PVC pipes jointed in cement mortar etc and taking from eaves gutters, and rainwater pipes from walls (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) including all type of bends/branch pieces complete all as specified and as directed. 56 S & F in repairs 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed in wall complete all as specified and as directed. 57 S & F in repairs 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed in wall complete all as specified and as directed. 58 S & F in repairs 75mm bore PVC (SWR) bends of any radius complete all as specified and as directed. 59 S & F in repairs 110mm bore PVC (SWR) bends of any radius complete all as specified and as directed. 60 S & F in repairs 75mm bore PVC (SWR) branch piece, single (double Y) equal or unequal bends of any radius, fixed with cement solvent, with oval access door complete all as specified and as directed. 61 S & F in repairs 110mm bore PVC (SWR) branch piece, single (double Y) equal or unequal bends of any radius, fixed with cement solvent, with oval access door complete all as specified and as directed. 62 S & F in repairs 75mm bore PVC (SWR) junction single (single T) equal or unequal bends of any radius, fixed with cement solvent, with oval access door complete all as specified and as directed. 63 S & F in repairs 110mm bore PVC (SWR) junction single (single T) equal or unequal bends of any radius, fixed with cement solvent, with oval access door complete all as specified and as directed. 64 Demolition of plain cement concrete as in ground floor and paving not exceeding 15 cm thickness below or above ground level (unreinforced concrete) including disposing of debris off the premises complete all as specified and directed. 65 M&L PCC 1:4:8 type D1 (using 40mm graded stone aggregate) as in sub base 75mm thick, finished fair & even complete all as specified and directed. 66 M&L for 75 mm thick; PCC 1:3:6 type C2 using 40mm graded stone aggregate, as in plinth protection, including finishing the surface by spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green and making saucer drain complete all as specified and directed. 67 Forming Construction joint 30mm deep x 10mm wide filled with sealing compound Grade A complete all as specified and directed. 68 Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removing the debris outside the defence land complete all as specified and directed. 69 M&L for Brickwork with Fly ash brick75 kg/cmsq compressive strength. Modularsize , is straight or curved on plan exc. 6 metermean radius built in cement mortar 1:6 complete all as specified and directed. 70 M&L for Brickwork with flyash bricks, 75 kg/cmsq compressive strength. Modularsize, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:6 complete all as specified and directed. 71 Taking down cement plaster on brick wallincluding raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed 72 M&L for rendering 10 mm thickon fair faces of brick or stone surfaces of walls in cement mortar 1:6 finished even and smooth without using extra cement with and including sagol finish complete all as specified and directed. 73 M&L for (10+5)mm thick for rendering fair faces of brick work or Concrete surface in two coats 10mm thick in CM(1:6) as under coat 5mm thick CM (1:4) as finishing coat in two separate layer mixed with Liquid water proofing compound finished even and smooth without using extra cement at any height including necessary scaffolding, ladder, formworketc complete all as specified and as directed. Note: Water proofing compund shall be measured and paied seperately. 74 M & L for 5mm thick rendering in 1:3 CM on ceiling, RCC facia and chujjs of fair faces of brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed. 75 M&L for water proof cement based putty @ 1 Kg (undiluted) per sqm of average thickness 2 mm over the plastered /old painted wall after scrapping to prepare the surface even and smooth complete and sanding of the putty surface with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 240 Grit or above to make the surface free from dust etc. by skilled labour as per following steps :- Step 1: Mix the putty powder by adding water as per manufacturers instructions and mix it with putty mixer with the mixing capacity of min 2.5 kg putty per minute. Step 2: Apply the first coat the prepared mixer with the help of fully automatic airless spray machine of putty application having flow speed of max 6 ltrs per minute with a maximum pressure 3300 PSI.Step 3: Allow 6-8 hours time to dry the putty surface. 76 M & L for preparing newly plastered surfaces of walls and applyingtwo coats of interior oil based emultion/distemper paint over one coat of acrylic water based interior/exteriorgrade primer @ 0.8 ltr (undiluted) / 10 Sqm diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI (Apex Ultima Luxury enulsion of Asian or equivalent of approvd make as approved by GE) or using smart periodical methodology complete all as specified & directed.Note : Shade and pattern of the colour will be approved by GE. 77 M & L for preparing newly plastered surfaces of walls andapplying two coat of weather shield/weather proof Acrylic exterior emulsion paint (Apex Ultima Luxury enulsion of Asian or equivalent of approvd make as approved by GE) by skilled labour and applying one coat of acrylic water based exteriorgrade primer @ 0.8 ltr (undiluted) / 10 Sqm diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI or using smart periodical methodology complete all as specified & directed. 78 M&L for preparing newly plastered surfaces of ceiling and applying two coat of white wash paint over a coat of alkali-resistant primer complete all as specified and directed. 79 M&L for complete removal of existing treatment (Cement Base Paint/White Wash/OBD/Exterior weather paint/Oil paint etc) of external decorative surface from walls, cornices,jambs, cills, parapet wall, pillars etc or any other description by scrapping with mechanical wall sander (having mechanical vacume mechanism) with RPM not less than 1500, sanding pad of 80 grit having dia of 7/9 or scrapping with wire brishesto to make the surface free from dust, loose paint, removal of nails etc including fillings depression surfaces, cracks/holes by waterproof cement based putty complete by skilled labour to the entire satisfaction by EIC complete all as specified and directed. 80 M&L for preparation of external old decorative surfaces of walls and applying two coat of weather shield/waterproof Acrylic exterior emulsion paint (Apex Ultima Luxury enulsion of Asian or equivalent of approvd make as approved by GE) by skilled labour and applyingone coat of acrylic water based exteriorgrade primer @ 0.8 ltr (undiluted) / 10 Sqm diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI. Allow 6-8 hrs to dry the surface for painting of subsequent coats including filling cracks with wall care putty wherever necessary complete all as specified and directed. 81 M & L for preparing of old decorative surface of ceilings and applying one coat of white wash on ceiling including cornices etc complete including filling cracks with wall care putty wherever necessary complete all as specified & directed. 82 M & L for preparing of old decorative any interior surface of walls and applying priming paint followed by one coat of interior emulsion paint, anti-fungal and anti-bacterial (Asian- Royale or equivalent of approved make as approved by GE) on wall surfaces using airless spray technology with max working presssure of 3300PSI and capable to operating single spray gun with max material whole length of 30mtr. The spray machine should be reported manufacturer with pro-gaurd technology and capability of tracking pressure and paint uses and certified by paint manufacturer and accesosries to be able to spray in hard to reach areas penetration of paint on the surfaceby smart periodical methodology/auto roller, complete in all respect as specified and directed 83 M & L for complete removal existing treatment of old decorative surface of walls (i.e. white wash, colour wash, cement base paint, synthetic enamel paint etc.) and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete including filling cracks with wall care putty wherever necessary complete all as specified & directed. 84 Material & Labour for cleaning of roof surfaces and applying a coat of oil base bituminous primer @ 0.30 lit per sqm over andincluding 15mm thick cement plaster in CM 1:4 mix with liquid water proofing admixture@200ml per bag of cement including laying of APP based polymeric membrane weighing not less than 3.00 kg/ Sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt,not less than 150gms/sq. m) land on primed surface by tension application with 100mm over lap travers and 150mm over lap longitunaland finishing the top surface by applying two coat of aluminium paint @ 0.1kg/sqm on each coat including taking down old treatment complete all as specified and directed. 85 Material & Labour for providingcement concrete 30mm thick PCC 1:2:4 type B-0 (12.5mm graded agg) as in padding on roofs slab to receive water proofing treatement, laid to required slope, finished even and smooth without using extra cement complete all as specified and directed. 86 Supply only liquid water proofing chemical. 87 M&L for repairing of R.C.C projections, chajjias, roofs, facia, columns, beams etc., in patches not exceeding 3 Sqm in each patch by necessary preparation, Scrapping, cutting, chiseling Dusting and cleaning exposed reinforcement, surfaces of damaged, loose R.C.C surfaces and applying one coat of cement slurry and filling the surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggregates and reinforced with welded mesh (If Reqd) with or without facia and finished with 15 mm thick cement and sand mortar (1:4) using coarse sand and thickness of R.C.C member n. exc 75mm including necessary form workat any height including dismantling of damaged concrete complete all as specified and directed. (Note :welded mesh will be measured and paid separately.) 88 S&F in repairs 20mm bore dia of pipe Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/20mm - 210 gms/25mm-455gms/40mm - 690 gms) complete all as specified and directed. 89 S&F in repairs 15mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. 90 M&L for reinforcement cement concrete slabs type B1 1:2:4 (20mm graded aggregate), supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves including necessary shuttering where required complete all as specified. 91 S & F mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. 92 Dismantling water tanks of capacity exc 250ltrs but n.exc 500ltrs complete all as specified and directed. 93 S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top),of capacity500ltrs hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed. 94 Demolition of Trellis work (Jafri), including taking as under of battens in trellis (posts and rails measured separately) complete all as specified and directed. 95 Taking down copper /aluminium point wiring (light, fan, bell, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendent, regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit a for above items should be made as per condition seperately) and making good distrubed surfaces ofwalls, floors etc complete all as specified and directed. 96 Taking down old unserviceable distribution board by disconnection of electric connection carefully SPN DBs/ TPN DBs/ Main Switch including old unserviceable MCCBs/ MCBs, isolators, etc and making good to disturbed surface complete all as specified and directed. 97 Taking down carefully copper/aluminium sub main wiring of any size from surface/concealed /existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed. 98 Taking down ceiling fan/ exhaust fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan blades and deposit to MES store yard of AGE E/M complete all as specified and directed. 99 Taking down existing single/three phase electric energy meter any capacity after disconnecting all necessary electrical connections and deposit to MES store yard of AGE E/M complete all as specified and directed. 100 M & L for point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sqmm (nominal area), two single core, PVC insulated and unsheathed FRLS cable 1100 volts grade IS-694 marked drawn through in and including heavy duty grade (ISI marked) PVC concealed conduit of white/ ivory colour including all accessories after chasing in wall/ceiling etc, with GI sunken boxeswith earth dolly duly, covered with modular white cover plate with inner frame suitable for modular switches, including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed for the One light point controlled by one, one way switch 5 Amps. Note:- Cost of Modular Cover Plate, Inner frame suitable for mounting modular switches, socket etc are deemed to be included in the quoted rate. 101 All as per Item No 100 above but one fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator complete all as specified and directed. 102 All as per Item No 100 above but One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board complete all as specified and directed. 103 All as per Item No 100 above but One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board complete all as specified and directed. 104 All as per Item No 100 above but One bell point controlled by one, bell switch 5 Amps complete all as specified and directed. 105 All as per item No. 100 above but using 2.5 sqmm single core copper conductor cable of multistranded FRLS PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket combination point including necessary running of 2.5 sqmm copper conductor FRLS PVC wire as earth continuity conductor along with wiring and connecting to the common earth dolly complete all as specified and directed. 106 S&F modular switch piano flush type, single pole, one way, 5/6 Amp single module complete all as specified and directed. 107 S&F modular switch piano flush type, single pole, one way, 15/16 Amp single module complete all as specified and directed. 108 S & F modular socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module piano flush type complete all as specified and directed. 109 S & F modular socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module piano flush type complete all as specified and directed. 110 S & F modular step type fan regulator 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and as directed. 111 S & F bell push modular 6 Amps single module complete all as specified and directed. 112 S & F ceiling rose, surface bakelite with 3 terminals, ISI marked for batten fitting complete all as specified and directed. 113 S & F lamp holder, PVC / polycarbonate type with back plate suitable for batten/ slanting fittings complete all as specified and directed. 114 S & F bell electric ding dong type suitable for operation on 230 volt 50 Hz AC supply complete all as specified and as directed 115 M & L for sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLS cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one run of PVC insulated with 6.0 Sqmm (nominal area) stranded copper conductor FRLS cable as earth wire complete all as specified and as directed. Note:- Two runs of 6 sqmm cable, one run of 6 sqmm cable and one run of PVC conduit will be measured as one unit 116 S & F sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of disturbed surface to match with existing colour of wall complete all as specified and as directed. 117 S & F MCB single pole and neutral rated capacity 32 Amps, 240 Volts breaking capacity 10 KA, C curve complete all as specified and as directed. 118 S & F MCB single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, C curve complete all as specified and as directed. 119 S & F ceiling fan 230V, 50 Hz AC, 1200mm sweep, min air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current motor (BLDC) complete with hanging arrangement by down rod alongwith steel wire rope for additional safety in ceiling fan with all allied accessories and connecting up with three core, 0.75 sqmm PVC insulated copper conductor cable complete all as specified and directed. 120 S & F exhaust fan, steel body AC single phase 230 Volts of size 300mm sweep with, blades, frame andlouvers with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 0.75 Sqmm three core from ceiling rose to exhaust fan forconnection complete all as specified and directed. 121 S & F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of size 0.75 sqmm complete all as specified and directed. 122 S & F LED light fitting 1x10 W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of size 0.75 Sqmm complete all as specified and directed. 123 S & F LED lights fitting 1x 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed. 124 S & F LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection and necessary mounting arrangements alongwith provision of 0.75 sqmm three core copper conductor cable multi stranded from ceiling rose to light fitting including suitable dia GI pipe medium grade bracket 0.75 mtr long bend to required shape with clamps, nut, bolts complete all as specified and directed. 125 Supply, installation, commissioning and testing indoor type LT wall mounting Panel Board of minimum size 1.20 m (height) x 1.20 m (breath) x 0.30m (depth) factory made CPRI approved panel, weather, dust & vermin proof indoor, double door, front openable, including four comparment for fixing of four Nos Single phase KWH meter, MCB TPN and providing glass view for reading of meter and providing rubber/ PVC gasket of suitable size all sides of door, with aluminium busbar wrapped with PVC tape/ sleeves with maintained the colour code and copper wire of suitable size, made out of 2.00 mm thick mild steel CRCA sheet with suitable size angle iron supporting frame including applying two coats of powder coated paint over a coat of red oxide zinc chrome primer over exposed external & internal surfaces suitable for 3 phase 4 wire system 415/440 volts grade including complete internal wiring with 10 sqmm copper wire and connections of all outgoing / incomming existing cable of any size complete all as specified and directed. (For G+1 Civ Md Accn) 126 INCOMMING(a) Aluminium strip busbar of size 50 x 5 mm wrapped with PVC sleeves with maintained the colour code and provision of making holes with Copper nuts, bolts & washers for cable connections including hydrograpic insulators with nuts & bolts at both ends = 04 Nos.(b)MCCBIP 44 and IP 66/67 protection, 4 pole, 415 volts, Lcu=25 KA breaking capacity, rating 63 Amps, adjustable thermal magnetic release including all fixing accessories with both ends spreader links -01 No(c) Digital voltmeter of range (0-500) volts, flush mounting type of size 100mm x 100mm (4”x4”) square dial with selector switch - 01 No.(d)LED Neon indicator lamp (RYB) with holder, 230/250 volts, AC -01 set (set of three).OUTGOING(a) MCB, Single pole & neutral, 40 amps, 240 volts, ‘C’ curve, 10 KA - 05 Nos (b) Fixing only existing electric meter- 04 Nos (obtained from item No. 5) 127 Taking down existing old unserviceable LT UG/service cable of any type or size complete all as specified and directed. 128 Supply and laying cable XLPE of size4 core x 16 sqmm insulated screened PVC bedded galvanised steel strip or wire armoured, electric power cable (heavy duty) 1100 volt grade with stranded aluminium conductor complete all as specified and directed. 129 Excavation in trenches n .exc 1.5 mtr wide and not exec 1.5 mtr in depth for foundation etc or for laying pipe lines and cables and getting out as in looses/soft soil complete all as specified. 130 Returning filling in including spreading leveling, watering and well ramming in layer not exe. 25 cm in soft/ loose soil, complete all as specified and directed. 131 Removing excavated material to a distance not exc 50m and depositing where directed at a level n.exc 1.5 mtr above the starting point complete all as specified. 132 Supply and laying river bed fine sand in trenches/ducts 15 cm under cable and 8 cm above the cable for cushioning/protection to cable including spreading, levelling and get thick 18cm after hand punning complete all as specified and directed. 133 Supply and laying for brick of common burnt clay, sub class B old size laid flat and dry on cables as in cable protection in treanches over cables perpendicular to direction of cables abutting each other complete all as specified and directed. 134 M & L for earthing complete with galvanized earth plate electrode 600mmx600mmx6mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5mtr below ground level connected to galvanised earth strip size 25x4 mm by means of nuts, bolts, washes of galvanized iron or steel all as shown in electrical plate No 5 and testing on completion including adequate charcoal dust comman salt necessary excavation & earth work PCC (1:3:6) type C-1 pit with precast RCC Cover slab 40 mm thick in PCC(1:2:4) type B-1 reinforced with 6 mm dia MS bars @ 100 mm c/c both ways with funnel wire mesh and 20 mm dia GI pipe medium grade as watering pipe and connected to earthing point complete all as specified and as directed. 135 Galvanised iron steel tubes, ISI marked light grade of size 40mm bore for cable protection along the poles under road under drains complete all as specified and directed.
