Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Brick work in 1:6 cement and Coarse sandmortarwith common burnt clay (non modular) bricks of class 150 in super structure above plinth level upto floor five level in all shapes and sizes |
| 2 | Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate I retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. Concrete of M20 grade with minimum cement content of 270 kg /cum |
| 3 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. The Mtro-Mechanically Treated bars of grade Fe-500D or more. |
| 4 | Centering and shuttering including strutting, propping etc. and removal of foMtr for SLAB BEAM |
| 5 | Centering and shuttering including strutting, propping etc. and removal of foMtr forSLAB |
| 6 | Providing and fixing bright /matt finished Stainless Steel Sliding Door Bolt of approved quality & make with necessary screws etc all complete. 250x16 mm. |
| 7 | Providing and fixing bright /matt finished Stainless Steel Tower Bolt of approved quality & make with necessary screws etc all complete. 250x10 mm. |
| 8 | Providing and fixing bright /matt finished Stainless Steel Tower Bolt of approved quality & make with necessary screws etc all complete. 150x10 mm. |
| 9 | Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.125 mm. |
| 10 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper |
| 11 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 12 | Providing and fixing ISI marked flush door shutters confoMtring to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 13 | Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). |
| 14 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality confoMtring to IS : 2046 Type S, including cost of adhesive of approved quality1.0mm thick |
| 15 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being teMtrite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. Frame size 50 x 100 mm . |
| 16 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diaMtr bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). |
| 17 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in charge. 35 mm thick shutters |
| 18 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge |
| 19 | (Door handle, lock and stopper etc |
| 20 | Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sach and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm foe series R3 and R4 profiles confoMtring to EN : 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and inline sash adaptor (where ever required) of appropriate dimension, EPDm gasket , hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing haedware and drainage of water etc. After Fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof sillicon sealant over backer rod of approved size and quality, all complete as per approved drawing confoMtring to CPWD specification & direction of Engineer-in-charge. Section of steel reinforcement and cross sections of uPVC Profiles to be as per design approved by Engineer-inCharge. Wire mesh/Glazing of plain/toughened/ laminated /double glass unit with / without high perfoMtrance coatings as per design requirements and confoMtring to IS :3548 & IS : 16231 shall be paid separately.Notes:- Structural design proof cheacked from a Government Engineering Institute, to be provided by the manufacturer for :(i) Sites with basic wind speed >45 m/Sec as per IS 875 - Part 3. (ii) Sites with structure height more than 20m for all wind speeds.Two track two panels sliding door with Aluminium channel for roller track, wool pile, zinc alloy (zamak) powder coated handle on two panels along with multi-point locking system, adjustable nylon rollers with SS 304 body. Using R3 series with frame (55 mm & above)x (40 mm & above) & sach (30 mm & above ) x (55 mm & above).(Height upto 1.8 Mtr). |
| 21 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and confoMtring to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/Sq Mtr including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Size of Tile 600 x 600 mm |
| 22 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platfoMtrs, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. completeat all levels. |
| 23 | Stone tile work for wall lining upto 10 m height with special adhesive over 12 mm thick bed of cement mortar 1 :3 (1 cement : 3 coarse sand), including pointing in white cement with an admixture of pigment to match the stone shade.8 mm thick (mirror polished and machine cut edge). Granite stone of any colour and shade . |
| 24 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. |
| 25 | Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 26 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/10 Sq Mtr over and including priming coat of exterior primer applied @ 2.20 kg/10 Sq mtr) |
| 27 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 28 | Centering and shuttering including strutting, propping etc. and removal of foMtr for Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 29 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per Sq Mtr as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 Mtr or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 30 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 31 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per Sq Mtr as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Gutter (600 mm over all girth) |
| 32 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 Sq Mtr over an under coat of primer applied @ 0.80 ltr/10 Sq Mtr of approved brand and manufacture |
| 33 | Providing and fixing reception table & chair as per design approved by architect & engineer in charge. |
| 34 | Providing and fixing Knauf Armstrong /Nittobo Heradesign Superfine/AMF, 1 layer magnesite bonded wood wool acoustic panel, 1mm thick fibre, exquisite surface structure, building biology recommended, size 1200 x 600 x 25mm, having edge detail AK-01 (5mm bevel on all 4 sides), weight 11.30Kg/Sq mtr, fire protection class B-s1,d0 as per EN 13501-1 & Humidity Resistance of 95%.Thickness Tolerance T2 (±1 mm/± 2 mm for 600/1200mm lengths respectively) according to EN 13168.Wood wool panels to be PEFC certified & should bear the Forest Stewardship Council Seal confiMtring that the wood used originates from responsibly managed forests.KCS UD profile 28mm/27mm/0.60mm is fixed to the wall, such that the base of the UD profile is 25mm above the planned finished ceiling level.KCS Primary CD profiles 60mm/27mm/0.6mm to be suspended at a centre to centre distance of 900m from the soffit using KCS Upper and KCS Lower Nonius hangers.The level of the Primary CD profile is such that the base of the Primary CD profile rests on the top of the UD profile.The Upper Nonius hangers are fixed to the soffit using 6mm dia anchor fasteners.The maximum distance between two Upper Nonius hangers should not exceed 900mm and the maximum distance between the first and the last Upper Nonius hanger to the wall should not exceed 150mm.The distance between the first Primary CD profile and the wall should not exceed 250mm.KCS CD Channel connectors (splice) to be used to connect two Primary CD profiles. The KCS Main CD profiles 60mm/27mm/0.60mm are fixed to the Primary CD profiles at a centre to centre distance of 600mm using the KCS CD intersection connector. The ends of the Main CD profile is inserted in the UD profile.CD Channel connectors (splice) to be used to connect 2 Main CD profiles.Heradesign wood wool boards to be screw fixed to the KCS Main CD profile using 6 screws (per board) 50/4.50mm dia Heradesign screws.The wood wool board should be backed by 40mm thick glass wool slabs packed in 1200 x 600mm polythene bags having a gross density of 50kg/m3.The finished face of wood wool panels have to be installed at a distance of 300mm from the soffit to achieve a NRC of 0.90 as per ASTM C423.Panels can be spray painted on site (before installation) under supervision of manufacturer. |
| 35 | Providing and fixing Armstrong /Knauf/Nittobo‘Optra Acoustical Wall Panelling’ with square edges made of fibre glass substrate 25mm thick and wrapped on the front side with an acoustically transparent and classified for Fire reaction ASTM E-84 : Class A fabric with an option of colors – Husk JT-06, Copper JT-13, Sangria JT-17, Sesame VL-27B, Coffee VL-08N, Charcoal JT-14, Titanium JT-07, Flame JT-16, Peanut JT-12, Shell VL-22 as per the choice of the Architect of size 600X600/1200/1800 mm providing a minimum sound absorption level of 0.85 NRC to be affixed to wall using Wall panel impalers supplied by M/s AMtrstrong Industries India Pvt Ltd and construction adhesives as per the instructions laid down by the manufacturer. INSTALLATION:3/4/5 Nos. AMtrstrong wall panel Impalers of shall be fixed to the wall surface using self-tapping screws. Silica based construction adhesive to be dabbed on to the projecting elements (spikes) of the impalers. AMtrstrong Optra wall panels shall be pierced through the spikes of the impalers ensuring the line and level of the panels are maintained. Installation to be carried out by AMtrstrong Trained Installation team & Installation should be carried out as per AMtrstrong recommended procedure. |
| 36 | Providing & Fixing of KNAUF Mineral Fibre Acoustical Suspended Ceiling System with 15mm thick Sierra OP Tegular 15/90 Edge Tiles with KNAUF Silhouette 15mm exposed grid.The tiles shall have smooth laminated visual with Humidity Resistance (RH) of 95%, NRC 0.85 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 standard, CAC of 25db as per ASTM E1414, Light Reflectance ≥86% as per ASTM E-1477, TheMtral Conductivity λ = 0.040 W/mK, Colour Global White, Fire PerfoMtrance of class A2-s1, d0 according to EN 13501-1 with 15mm Tegular 15/90˚ edge and 8mm drop in module size of 600 x 600mm. The scrim on the face of the tile shall be cleanable and classified as ISO 14644-1 cleanroom class 5. It shall be suitable for Green Building application, with Recycled content of 43% VOC Emissions (French) class of A+. The tile shall have Environmental Product Declaration as per ISO 14025 and EN 15804+A2. The tile shall comply with Indoor Air Comfort Gold requirements, version 7.0 (2020) and this certification shall ensure compliance with LEED & DGNB, French VOC class A+, French HQE certification, GeMtran Regulation (AgBB/ABG), Italian CAM Edilizia, BREEAM International NOR NL, WELL Building, SKA Rating, BVB (Sweden), Eco Product Norway, Blue Angel DE-UZ 132, M1, Danish Indoor Climate Label, Singapore Green Label and GreenTag Australia. The tile shall have certifications from GRIHA and GreenPro thereby confiMtring that it is an environment friendly product.SUSPENSION: The tile shall be laid on KNAUF Silhouette 38 profile grid system with 15mm white flanges incorporating a 6mm central reveal in white/black colour with mitred ends & “bird’s mouth” notches to provide mitred crucifoMtr junctions colour global white (Matching to tile color). Grid shall have double stroke rotary stitching on all T sections i.e., the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38mm (all sections). The deflection loading of the system shall be 7.9 kg/m2 (as per standard installation layout mentioned below) and main beam tested as per ASTM C635 (Deflection limit less than L/360) with a deflection loading of 9.5 kg/m. The end details of the cross tee shall be made of pre hardened steel clip fixed to the ends of the cross tee to provide double locking between “cross tee to cross tee” and “cross tee to main beam”. All main beam to main beam and cross tee to cross tee connection shall have a pull-out strength of more than 100kg. The T Sections shall be made of 90 gsm as per IS 277 (2003) pre-painted steel with baked polyester paint of 0T bending capability. |
| 37 | Providing and Fixing Armstrong/Knauf/Nittobo Channeled Woodworks perforated panels of width 192mm, thickness of 15mm and length 2400 mm or as required by the Architect/ approving engineer, made of a high density fibre board with minimum 725 Kg/M3 density substrate with a laminated facing as per the approved shade & finish and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where the visible surface has a “Helmholtz” fluted perforation of 3mm width and 5mm/ 13mm/ 21mm of visible panel Nos. The edges of the panels shall be “tongue-and-grooved” to receive special clips for installation. The back of the perforated panel shall have sound absorbing non-woven acoustical fleece having NRC of 0.59. The panels shall be mounted on special aluminium splines using clips provided by AMtrstrong and approved by the Architect/ Engineer-in-Charge.INSTALLATION: Install wooden battens (provided by others) of section 50x50mm or as approved by the Architect on the solid wall horizontally using screws and plugs at spacing of 600mm centre-to-centre. Screw the aluminium extruded keel for channelled woodworks provided by AMtrstrong over the lowest and second wooden batten at an on-centre distance of 600mm. Install the Skirting (provided by others) of width 50mm or more as required by the Architect/ Engineer-in-Charge and insert the tongue end of the panel in the skirting. Place the inside clip on the groove end of the panel along the Al keel and then place the tongue end of the next panel. Continue installing rows of panels by inserting the tongue into the groove of the earlier inserted panel and progressively installing inside clips into the next keel till the actual height is achieved. Finish off the edges using wooden moulding of matching colour (provided by others). Installation to be carried out by AMtrstrong Trained Installation team & Installation should be carried out as per AMtrstrong recommended procedure. |
| 38 | .Providing & Fixing of Forbo Flotexcolor series flocked floor covering rolls having a density of 70 million fibres of nylon 6.6 per Sq Mtr , Fire Test EN-13501, Appearance Retention Hexapod ISO 140-8, Friction Slip Resistance Test EN 14041 Class DS, sanitized anti-microbial treatment with resilient waterproof backing ,anti allergiccertified by British allergy foundation, anti static, stain resistant, thickness 4.3 mm and approximate weight of1.8 k.g./Sq Mtr of roll foMtr with acoustic sound impact 17dB. Flotex to be installed over cement basedsmooth level hard flooring.. The carpet should be laid complete includingcompany recommended adhesive and accessories.Make-AMtrstrong/FlooMtraster/Forbo. |
| 39 | Rewiring for light point/ fan point/ exhaust fan point/ call bellpoint with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel/PVC conduit including dismantling as required. POLYCAB/FINOLEX/KEI |
| 40 | Rewiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel/PVC conduit including dismantling as required. |
| 41 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit alongwith 1 Nos 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. POLYCAB/FINOLEX/KEI |
| 42 | Wiring for circuit/ submain wiring alongwith earth wire with thefollowing sizes of FRLS PVC insulated copper conductor, singlecore cable in surface/ recessed steel conduit as required.2 X 6 sq. mm + 1 X 6 sq. mm earth wire |
| 43 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire POLYCAB/FINOLEX/KEI |
| 44 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire POLYCAB/FINOLEX/KEI |
| 45 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 10 sq. mm + 1 X 6 sq. mm earth wire POLYCAB/FINOLEX/KEI |
| 46 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.4 X 10 sq. mm + 2 X 6 sq. mm earth wire POLYCAB/FINOLEX/KEI |
| 47 | Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unaMtrored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.2 Pair POLYCAB/FINOLEX/KEI |
| 48 | Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.1 run of cable POLYCAB/FINOLEX/KEI |
| 49 | Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.25 mm POLYCAB/FINOLEX/KEI |
| 50 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm POLYCAB/FINOLEX/KEI |
| 51 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 A switch. POLYCAB/FINOLEX/KEI |
| 52 | Supplying and fixing following modular switch/ socket on theexisting modular plate & switch box including connections butexcluding modular plate etc. as required.2 way 5/6 A switch |
| 53 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 A switch. POLYCAB/FINOLEX/KEI |
| 54 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 A socket outlet. POLYCAB/FINOLEX/KEI |
| 55 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 A socket outlet. SCHNEIDER/LEGRAND ARTEOR/HONEYWELL BLENZ PLUS. |
| 56 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.Telephone socket outlet.SCHNEIDER/LEGRAND ARTEOR/HONEYWELL BLENZ PLUS. |
| 57 | Supplying and fixing following modular switch/ socket on theexisting modular plate & switch box including connections butexcluding modular plate etc. as required.TV socket outlet |
| 58 | Supplying and fixing following modular switch/ socket on theexisting modular plate & switch box including connections butexcluding modular plate etc. as required.Bell Push |
| 59 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.RJ45 socket cat 6 with shutter.SCHNEIDER/LEGRAND ARTEOR/HONEYWELL BLENZ PLUS. |
| 60 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.SCHNEIDER/LEGRAND ARTEOR/HONEYWELL BLENZ PLUS. |
| 61 | Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.1 or 2 Module (75mmX75mm) HONEYWELL/LEGRAND/SCHNEIDER |
| 62 | Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.3 Module (100mmX75mm)HONEYWELL/LEGRAND/SCHNEIDER |
| 63 | Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.4 Module (125mmX75mm)HONEYWELL/LEGRAND/SCHNEIDER |
| 64 | Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 6 Module (200mmX75mm)HONEYWELL/LEGRAND/SCHNEIDER |
| 65 | Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 8 Module (125mmX125mm) |
| 66 | Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 12 Module (200mmX150mm)HONEYWELL/LEGRAND/SCHNEIDER |
| 67 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.SCHNEIDER/LEGRAND ARTEOR/HONEYWELL BLENZ PLUS. |
| 68 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 Nos. 3 pin 5/6 A modular socket outlet and 2 Nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).SCHNEIDER/LEGRAND ARTEOR/HONEYWELL BLENZ PLUS. |
| 69 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.SCHNEIDER/LEGRAND ARTEOR/HONEYWELL BLENZ PLUS. |
| 70 | Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \"C\" curve including connections, painting etc. as required.SCHNEIDER/LEGRAND ARTEOR/HONEYWELL BLENZ PLUS. |
| 71 | Supplying and fixing brass batten/ angle holder including connection etc. as required. |
| 72 | Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. |
| 73 | Supply & fixing of 12Watt Mirror Light PHILIPS/WIPRO/BAJAJ |
| 74 | Supply & fixing of 20 Watt TrackLight |
| 75 | Supply and fixing of 9W LED retrofit bulb. PHILIPS/WIPRO/BAJAJ |
| 76 | Supplying and fixing PVC batten/ angle holder including connections etc. as required. |
| 77 | Supply and fixing of recess/ Surface/ Pendent mounting round 6 Watt 8 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect. PHILIPS/WIPRO/BAJAJ |
| 78 | Supply of 15W Green PerfoMtr Sleek is a high perfoMtrance low-height LED downlighter suited for requirements of any modern professional workspace. Robust PDC housing ensures long system. Narrow rim renders a pleasing aesthetic look. similar to Philips DN295B LED8S-6500 PSU WHor equivalent. PHILIPS/WIPRO/BAJAJ |
| 79 | Supply of Pressure die cast housing LED bulkhead with IP66protection and IK09 impact resistance suitable for surface and wall mounting applications. Similar to Philips Cat Ref. WT202W LED6S NW PSU S2 PC or equivalent. |
| 80 | Supply of 22W Extruded aluminium batten available in 4ft run length with multiple lumen packages and suitable for surface, wall & conduit mounting (with accessories). etc. PHILIPS/WIPRO/BAJAJ |
| 81 | Supply and fixing of 36 Watt to 46 Watt indoor Recess mounting LED Square Fitting for AMtrstrong Ceiling having Powder coated die cast aluminium housing body with extended heat sink and diffuser of Special Polycarbonate Mtrial and driver set complete in all respect. PHILIPS/WIPRO/BAJAJ |
| 82 | Supply of plastic body ventilation fan, 250mm sweep continously rated highly efficient similar to Crompton Cat. Efficio\" or equivalent. PHILIPS/WIPRO/BAJAJ |
| 83 | Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 Nos. blades, 30 cm long down rod, 2 Nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. CGE/HAVELLS/BAJAJ |
| 84 | Supply and fixing hexagonal Round G.P.fan box approved make made up of 1.0 mm thickISI Marked G.P.sheet spot welded Four to Eightholes for pipe entryof the box. Holes should be semi-shuttered type with 0.5 mm G.P. Sheet made upper & lower cover duly screwed. Fixing with wiring conduit laid in the R.C.C. roof before concretingalongwith supply of all material, labour, T&P etc. required for proper completion of the work. |
| 85 | Supply of Totally enclosed exhaust fan, 300mm sweep continously rated highly efficient heavy-dutymotor similar to Crompton Cat. Ref. Trans Air 12\" or equivalent. CGE/HAVELLS/BAJAJ |
| 86 | Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.Upto 450 mm sweep |
| 87 | Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes. |
| 88 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)6 way , Double door |
| 89 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)8 way , Double door |
| 90 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)12 way , Double door.SCHNEIDER/ABB/LEGRAND |
| 91 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)4 way (4 + 12), Double door |
| 92 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)6 way (4 + 18), Double door |
| 93 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)12 way (4 + 24), Double door |
| 94 | Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is noMtrally usedwhere 3 phase outlets are required.)6 way (4 + 12), Double door suitable with 160Amp Incomer |
| 95 | Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is noMtrally usedwhere 3 phase outlets are required.)6 way (4 + 12), Double door suitable with 125Amp Incomer |
| 96 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole SCHNEIDER/ABB/LEGRAND |
| 97 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Double pole |
| 98 | S&F of 160 Amp 4 pole MCCB (16 KA) TheMtral Magnetic release |
| 99 | S&F of 125 Amp 4 pole MCCB (16 KA) TheMtral Magnetic release |
| 100 | Supplying and fixing 63Amp, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 300 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. Similar to Legrand or equivalent. |
| 101 | Supplying and fixing 40/63A rating, 415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of Four poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Similar to Legrand DX3 AC MCBs or equivalent. |
| 102 | Supplying and fixing 40/63A rating, 415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of Three poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Similar to Legrand DX3 AC MCBs or equivalent. |
| 103 | Supplying and fixing 40Amp, Two pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 300 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. Similar to Legrand or equivalent. |
| 104 | Supplying and fixing 40A rating, 415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of Two poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Similar to Legrand DX3 AC MCBs or equivalent. |
| 105 | Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.100 mm width X 50 mm depth X 1.6 mm thickness |
| 106 | Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.300 mm width X 50 mm depth X 1.6 mm thickness |
| 107 | Supplying and installing following size of perforated paintedwith powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.600 mm width X 50 mm depth X 1.6 mm thickness |
| 108 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. AKG/POLYCAB/CAP WIRE-POLYCAB/FINOLEX/KEI |
| 109 | 4 X 10 sq. mm + 2 X 6 sq. mm earth wire |
| 110 | Supply, Installation, Testing & Commissioning of2 Mtrs USB-USB, USB-A to USB-B moulded Cable complete with standard accessories as required.SCHNEIDER/LEGRAND ARTEOR/HONEYWELL BLENZ PLUS. |
| 111 | Supply, Installation, Testing & Commissioning of 2 Mtrs USB 3.0 A to A (Male) Molded Cable complete with standard accessories as required.SCHNEIDER/LEGRAND ARTEOR/HONEYWELL BLENZ PLUS. |
| 112 | Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.1 Run of Cable POLYCAB/FINOLEX/KEI |
| 113 | Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 25mm Dia BEC/RM COM/STEEL CRAFT |
| 114 | Supply, Installation, Testing & Commissioning of Modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling & heating having 100% hermetically sealed inverter type twin Scroll Compressor(s), minimum two compressors (with individual seperate PCB) for above 14HP modules, micro processor based Controller, top discharge type condensing unit(s), with R-410-A Refrigerant , vibration Isolators with suitable foundation etc. complete as required. To have better efficiency condensor fan shall be capable to operate at different speed with respect to load. The unit shall deliver the rated capacity and in confimation as per IS 18728:2024 and CPWD Specifications and work even at 50°C ambient temperature without tripping. The system shall be able to deliver 100% of the rated capacity upto 39 Degree Celcius. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply and BMS compatible. The unit shall be filled with first charge of the refrigerant and ready for use as required. The condenser should be coated with a hydrophilic film to prevent water accumulation on the surface of the heat exchanger, enhance water dispersion, and reduce the risk of degradation, thereby improving overall perfomance and durability. The Indian Seasonal Energy Efficiency Ratio (ISEER) of the unit shall be as per Energy Conservation and Sustainable Building Code (ECSBC) 2024 as below and complete as per CPWD specification, connections, inter connections etc. as required. (For capacity <40 kWr ISEER 6.4, Capacity >40 and <70 ISEER 6.5, Capacity > 70 ISEER 6.6 for ECSBC+ Building) For Cooling &Heating 10 HP TO 12 HP HITACHI/DAIKIN/MITSUBISHI/ Blue STAR. |
| 115 | Supply, Installation, Testing and Commissioning of following minimum capacity 4 way Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan /dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration Isolation, Corded remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Signals. The system shall be capable to adjust air flow as per room requirement in auto mode. The cooling capacity of each indoor unit will be 3.6 TRat air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature HITACHI/DAIKIN/MITSUBISHI/ BLUE STAR. |
| 116 | Supply, Installation, Testing and Commissioning of Y-Joints/T/Multi Joints. Joints shall be of same Original Equipment Manufacturer (OEM) make as of ODUs and IDUsIndoor Units HITACHI/DAIKIN/MITSUBISHI/BLUE STAR. |
| 117 | Supply,Installation,testing and commissioning of cordedCord type remote control with thermostat, LED Display and internal wiring for Cassette. HITACHI/DAIKIN/MITSUBISHI/BLUE STAR. |
| 118 | Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closedcellelastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessoriesasper specifications etc. as required :9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm MAXFLOW/RAJCO/TOTALINE |
| 119 | Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closedcellelastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessoriesasper specifications etc. as required :15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm MAXFLOW/RAJCO/TOTALINE |
| 120 | Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closedcellelastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessoriesasper specifications etc. as required :22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm MAXFLOW/RAJCO/MANDEV |
| 121 | Supply installation testing commissioning Shielded Control Cables for VRV System with necessary ISI mark Medium class rigid PVC pipes with necessary accessories with teMtrination in machine and control equipments.2Cx1.5 Sq mm Shielded AMtroured(for communication lead & remote ) POLYCAB/KEI/FINOLEX |
| 122 | Supplying & erecting XLPE(IS:7098)(I)-88 ISI unaMtroured copper cable 1.1 KV grade to be erected as directed of following size.3C x 2.5 sq.mm FOR INDOOR UNIT POWER CABLE |
| 123 | Commissioning of VRF systems including charging ofR410A gas as per site requirements |
| 124 | Supply,installation,testingandcommissioningofanodisedaluminium airlouvers with bird screenas per specifications and drawings. |
| 125 | Supply, installation & testing of GI back draft dampers (16 G Blade & Frame) similar constrctiontogravitylouvers |
| 126 | Rigid UPVC drain pipe of 10 Kg/cm2. rating with 9 mm thick.nitrile rubber insulation.25 mm dia. |
| 127 | Supply, Installation, Testing and Commissioning of Y- Joints/T/Multi Joints. Joints shall be of same Original Equipment Manufacturer (OEM) make as of ODUs and IDUsIndoor Units HITACHI/DAIKIN/MITSUBISHI/BLUE STAR. |
| 128 | Supply, Installation, Testing and Commissioning of Y- Joints/T/Multi Joints. Joints shall be of same Original Equipment Manufacturer (OEM) make as of ODUs and IDUsOutdoor Units Multi Joint HITACHI/DAIKIN/MITSUBISHI/BLUE STAR. |
| 129 | Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closedcellelastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessoriesasper specifications etc. as required :6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm MAXFLOW/RAJCO/MANDEV |
| 130 | Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closedcellelastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessoriesasper specifications etc. as required :9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm MAXFLOW/RAJCO/MANDEV |
| 131 | Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closedcellelastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessoriesasper specifications etc. as required :12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mmMAXFLOW/RAJCO/MANDEV |
| 132 | Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closedcellelastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessoriesasper specifications etc. as required :15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm MAXFLOW/RAJCO/MANDEV |
| 133 | Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closedcellelastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessoriesasper specifications etc. as required :19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm MAXFLOW/RAJCO/MANDEV |
| 134 | Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closedcellelastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessoriesasper specifications etc. as required :22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm MAXFLOW/RAJCO/MANDEV |
| 135 | Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closedcellelastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessoriesasper specifications etc. as required :28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm MAXFLOW/RAJCO/MANDEV |
| 136 | Supply installation testing commissioning Shielded Control Cables for VRV System with necessary ISI mark Medium class rigid PVC pipes with necessary accessories with teMtrination in machine and control equipments.2Cx1.5 Sq mm Shielded AMtroured(for communication lead & remote ). |
| 137 | Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable 1.1 KV grade to be erected as directed of following size.3C x 2.5 sq.mm FOR INDOOR UNIT POWER CABLE |
| 138 | Commissioning of VRF systems including charging ofR410A gas as per site requirements |
| 139 | Supply,installation,testingandcommissioningofanodisedaluminium airlouvers with bird screenas per specifications and drawings. |
| 140 | Supply, installation & testing of GI back draft dampers (16 G Blade & Frame) similar constrctiontogravitylouvers |
| 141 | Rigid UPVC drain pipe of 10 Kg/cm2. rating with 9 mm thick.nitrile rubber insulation.40 mm dia. |
| 142 | Rigid UPVC drain pipe of 10 Kg/cm2. rating with 9 mm thick.nitrile rubber insulation.32mm dia. |
| 143 | Rigid UPVC drain pipe of 10 Kg/cm2. rating with 9 mm thick.nitrile rubber insulation.25 mm dia. |
| 144 | Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. |
| 145 | Providing & fixing white vitreous china Under Counter wash basin with C.I. brackets painted white, with rubber plug, 32mm C.P. brass waste of standerd pattern including cutting & making good the walls wherever required. a)White Vitreous China Wash basin size (605x410x200)mm. Grohe/Toto/Roka |
| 146 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.32 mm dia. Grohe/Toto/Roka |
| 147 | Providing and fixing 600x450mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 148 | Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. Grohe/Toto/Roka |
| 149 | Providing and fixing stone slab table rubbed, edges rounded and polished of size 75x50cm deep and 1.8cm thick fixed in Urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1cement: 2coarse sand: 4graded stone aggregate 6mm nominal size) as per direction of Engineer-in-charge and finished smooth.Granite Stone of approved shade. |
| 150 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 Mtr long with S.S. triangular plate to Eureopean & Wall moutain type W.C. of quality and make as approved by Engineer - in - charge. Grohe/Toto/Roka |
| 151 | Providing and fixing C.P. brass bib cock of approved quality confoMtring to IS:8931a) 15 mm nominal bore Grohe/Toto/Roka |
| 152 | Providing and fixing C.P. brass long body bib cock of approved quality confoMtring to IS standards andweighing not less than 690 gms. ( for sink) a) 15 mm nominal bore. Grohe/Toto/Roka |
| 153 | Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality confoMtring to IS:8931a) 15 mm nominal bore Grohe/Toto/Roka |
| 154 | Central Hole Basin Mixer with Popup Waste System with 450mm Long Braided HosesGrohe/Toto/Roka |
| 155 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. Grohe/Toto/Roka |
| 156 | Providing and fixing S.S. liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. Grohe/Toto/Roka |
| 157 | Providing and fixing S.S. towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms. |
| 158 | Providing and Fixing Toilet Paper Holder:C.P. Brass |
| 159 | Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905a) 100mm dia centrifugally cast iron S & S pipe. NICO/SAINT GOBAIN/SKF |
| 160 | Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905b)75mm dia centrifugally cast iron S & S pipe. NICO/SAINT GOBAIN/SKF |
| 161 | Providing and fixingGI pipes complete with GI fittings and clamps, including cutting and making good walls etc. ( for wash basin waste )32mm dia nominal bore |
| 162 | Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe. SS 304 grade coupling with EPDM rubber gasket NICO/SAINT GOBAIN/SKF |
| 163 | Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe.b)75mm |
| 164 | Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe.SS 304 grade coupling with EPDM rubber gasket NICO/SAINT GOBAIN/SKF |
| 165 | Providing & fixing M.S. holder bat clamps of approved design to sand cast iron/centrifugally cast (Spun) iron S & S pipe embeded in & including cement concrete blocks 10x10x10cm. of 1:2:4 mix (1 cement : 2 coarse : 4 graded stone aggregate 20mm nominal a) for 100mm dia pipe. NICO/SAINT GOBAIN/SKF |
| 166 | Providing & fixing M.S. holder bat clamps of approved design to sand cast iron/centrifugally cast (Spun) iron S & S pipe embeded in & including cement concrete blocks 10x10x10cm. of 1:2:4 mix (1 cement : 2 coarse : 4 graded stone aggregate 20mm nominal b) for 75mm dia pipe. NICO/SAINT GOBAIN/SKF |
| 167 | Providing & fixingcast iron coller.a) 100mm dia. NICO/SAINT GOBAIN/SKF |
| 168 | Providing & fixingcast iron coller.b)75mm dia. NICO/SAINT GOBAIN/SKF |
| 169 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent aMtr complete, including cost of cutting and making good the walls and floors :a) 100mm inlet & 100mm outlet. NICO/SAINT GOBAIN/SKF |
| 170 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent aMtr complete, including cost of cutting and making good the walls and floors :a) 100mm inlet & 75mm outlet. NICO/SAINT GOBAIN/SKF |
| 171 | Providing and fixing bend of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete.a) 100mm |
| 172 | Providing and fixing bend of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete.b) 75mm |
| 173 | Providing and fixing plain bend of required degree.Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905a) 100mm |
| 174 | Providing and fixing plain bend of required degree.Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905b) 75mm |
| 175 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMtral stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge.15mm dia nominal outer dia pipes ASTRAL/AJAY/SUPREME |
| 176 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMtral stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge.20mm dia nominal outer dia pipes ASTRAL/AJAY/SUPREME |
| 177 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMtral stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge.25mm dia nominal outer dia pipes ASTRAL/AJAY/SUPREME |
| 178 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMtral stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.25mm dia nominal bore ASTRAL/AJAY/SUPREME |
| 179 | Providing and fixing gun metal gate valve with wheel of approved quality.25mm dia nominal bore ZOLOTO/SANT/AUDCO |
| 180 | Providing and fixing gun metal gate valve with wheel of approved quality.32mm dia nominal bore ZOLOTO/SANT/AUDCO |
| 181 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :25 mm nominal bore ASTRAL/AJAY/SUPREME |
| 182 | Providing and fixing A standard drinking water cooler typically features a stainless steel body and tank (SS304), with a cooling capacity ranging from 20 to 150 liters per hour and a storage capacity of 20 to 150 liters. It operates on a 220–240V, 50Hz single-phase power supply, consuming approximately 300 to 1000 watts depending on size. The unit uses eco-friendly refrigerant like R134a, maintains cold water temperature between 10°C to 15°C, and is insulated with PUF for the Mtral efficiency. MAKE: VOLTAS/USHA/BLUE STAR |
| 183 | Total (from Item No. 1 to Item No.162) :\"A\" |
| 184 | Add GST @18% on \"A\" |
| 185 | Grand Total with GST |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
