Tender For Provision Of Multipurpose Training Shed At Chakabama Mil Station; 1 Excavating over areas, n exc 1.5 m deep and getting out in hard/dense soil etc complete all as specified and as directed. 2 Excavating over areas,exc 1.5 m but not exc. 3m deep and getting out in hard/dense soil etc complete all as specified and as directed. 3 Material and labour for PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in foundations,filling and mass concretecomplete all as specified and as directed. 4 Spreading and levelling in layers not exceeding 25cm thick, well ramming including watering as required complete all as specified and directed. 5 Moorum/ red bajri filling in floors or pavings , laid in layersn exe 150 cm thick (Compacted thickness) ,spread, levelled ,rammed including watering complete all as specified and directed. 6 Material and labour for hardcore of broken stone / bouldergauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed. 7 Material and labour for reinforced cement concrete (design mix) in M-25 (20mm graded aggregates) for foundation and plinth beams etc complete all as specified and directed.Note:- Reinforcement and form work required shall be measuredNote:-(i) Reinforcement and form work required shall be measured and paid seperately(ii) Design mix will be approved by the Accepting Officer. 8 Materials and labour for use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter with rough finished flat surfaces of concrete complete all as specified and as directed. 9 Material and labour for Reinforced cement concrete (design mix) in M-25, (20 mm graded aggregate) in columns/pillars complete all as specified and directed.Note:- (i) Reinforcement and form work required shall be measured and paid seperately(ii) Design mix will be approved by the Accepting officer. 10 Materials and labour for use and waste of form work to pillars, posts, struts, piers, columns and stanchions with rough finished square, rectangular, or polygonal surfaces of concrete complete all as specified and as directed. 11 Material and labour for mild steel TMT bars 10mm dia and over, cut to length bent to shape required, including cranking bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and as directed. 12 Material and labour for mild steel TMT bars 5mm dia and over and upto and including 10mm dia, cut to length bent to shape required, including cranking bending spirally for hooping for stirrups, spacers, binders and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and as directed. 13 Material and labour for brick work with sub class `B` bricks, old size,straight or curved on plan exc 6m mean radius built in cement mortar (1:6)complete all as specified and as directed. 14 Materials and labour for 15 mm thick rendering on fair faces of brick work mixed with water proofing compound @ 2% by weight of cement content in cement mortar (1:4) on wall andfinished the surfaces even and smooth without using extra cement complete all as specified and as directed.Note : WPC will be measured and paid separately under respective items. 15 Materials and labour for 10mm thick rendering on fair faces ofbrick work or concrete surface in cement mortar (1:6) andfinished the surfaceseven and smooth without using extra cementcomplete all as specified and as directed. 16 Supply only integral water proofing compound (WPC) of best quality completeall as specified and as directed. 17 Material and labour for 75mm thick PCC (1:2:4) type B-2 (using 40mm graded stone aggregate) as in sub base floor and finish the surface even and rough to receive the topping layer complete all as specified and as directed. 18 Material and labourfor Preparation newly plastered wall surfaces and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed. 19 M & L for preparation of newly plastered wall surfaces and applying two coats of Cement Based paint over a coat of Alkali Resistant Primer complete all as specified and as directed. 20 Supply and fixing Mild Steel work as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe-290, Grade E-165 complete all as specified and directed. 21 Supply and fixing rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe-410-W (Gde E-250) quality- Acomplete all as specified andas directed. 22 Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws as per manufactures instruction complete all as specified and as directed. 23 Pre-painted galvalume aluminium zinc coating GI based plain steel sheet0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws asper manufactures instruction complete all as specified and as directed. 24 Material and labour for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed. 25 Material & Labour for 75mm thick, PCC 1:3:6, Type C-2, using 40mm graded aggregate as in Plinth protection etc surface finished even and smooth with out using extra cement and providing necessary joints 12mm wide to the full depth of PCC at every 3 meters and every change of directions and the joints duly filled with mastic filling comprising of 01 Part of heated bitumen blown grade any penetration and 3 parts of sand [all by weight] complete all as specified and as directed. 26 Material & Labour for joint free non skid ceramic coloured tiles7 to 8mm thick (square /rectangular) of premium quality, area of each tile exceeding 0.06 sqm but not exc 0.11sqm in floors etc.set & jointed in neat cement slurry & pointed in white or coloured cement to match including screed bed of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by AGE(I) 27 Returning, filling in, of soil including spreading leveling, watering and well ramming in layers not exceeding 25 cmcomplete all as specified and directed . 28 Removing excavated soft/loose soil n.exc 50 mtrand depositing where directedat a level n.exc 1.50m above the starting point complete all as specified and directed. 29 Material and labour for point wiring (surface type) for one light/fan/call bell point with 1.5 sqmmPVC insulated (FR-LS) unsheathed copper cable multistranded conductor 1100 volts gradecontrolled by one way switchincluding 1.5 sqmm PVC (FR-LS) insulated unsheathed copper cable multistrand conductor 1100 volts grade for continuity earth wire connected to common earth dolly drawn through and including PVC casing caping of suitable size with all accessoriesand PVC rectangular boxes for mounting switch, socket and fan regulator etc complete all as specified and as directed. Note: (i) Wiring shall be done in proper colour coding using red , yellow, blue for phase, black for neutral and green for earth. 30 All as per item No 29 above but for 3 pin,5 Amp switch Socket outlet on independent board complete all as specified and directed. 31 All as per item No 29 above but for 3 pin, 5 Amp Socket outlet on the same board complete all as specified and directed. 32 All as per item no 29 here in before but for one 3 pin 16 Amps socket outlet on independent boardwith 2.5 sqmmPVC (FR-LS) insulated un-sheathed copper conductor cable multistranded conductor 1100 volts grade and 2.5 Sqmm PVC (FR-LS) copper conductor cable as earth continuity conductor. 33 Supply & fixing switch piano flush type (ISI marked), single pole, one way 5 Amp, 240 Volts complete all as specified & directed. 34 Supply & fixing switch piano flush type (ISI marked), single pole, one way 16 Amp, 240 Volts complete all as specified & directed. 35 Supply and fixing ceiling rose, 3 phase/PVC/ polycarbonate, isolated body complete all as specified and as directed. 36 Supply and fixing socket out let 5 Pin, 6 Amps flush typecomplete all as specified and as directed. 37 Supply and fixing Socket Outlet, 3 pin, 16 Amps and 1 pin, 5 Amps, Flush Type, Two Modules, Multipurpose, 230 Volts complete all as specified and as directed. 38 Supply and fixingLamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed. 39 Supply and fixing LED bulb, 10 W, Correlated colour temperature 3000 K, ball shape, Base type E-27 complete all as specified and as directed. Note: Light fitting shall be of PF>0.95 40 Supply and fixing LED batten with LED tube 20W LED 6000K T8 LED lighting fixture with extruded polycarbonate, environment friendly, energy efficient, 230V. 50Hzcomplete all as specified and as directed.Note: Light fitting shall be of PF>0.95 41 Supply and fixingIntegrated LED Bulk head with luminaire of 10W, 6000 K with Pressure Die Cast Aluminium Housing, IP54 protection, heat resistant glass cover, high power LEDs as light source, electronic driver and connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95 42 Supply & Fixing Energy efficient, Low Noise, Ceiling Fan, 1200mm Sweep of any colour as approved, 03 blades, BEE 5 Star Rated, with BLDC Motor, Copper Wound, 350 RPM, with Double Ball Bearing, Conforming to IS - 374, ISI Marked, suitable for operation on Single Phase, 240 Volts, AC, 50Hz, including Down Rod, Canopies, Shackles, Safety Rope, Hanging Clamps, Bushes, having P.F >0.95, Service Value >6.5, Air Delivery >215 CMM, Power Consumption less than 35 Watt, THD less than 5%including provision of Electronic speed control Regulator step type, including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mmcomplete all as specified and as directed. Note: Ceiling Fan shall be provided with 03 Years onsite replacement warranty. Rate quoted is deemed to be including the same and nothing shall be paid extra on this account. 43 Supply and fixing stepped type electronic fan regulator flush type complete all as specified and as directed. 44 PVC rectangular block for mounting, switches, sockets, fan regulator etc. with 3 mm thick plastic laminated sheet cover of size 250 mm x 200 mmand 50 mm deep complete all as specified and as directed. 45 Supply and fixing of MCB DB SPN 8 ways double door including bus bar neutral link, 240 Volts, earth bar and din rail,recessed with wall surfaces by chase cutting and making good surfaces of wall complete all as specified and as directed. 46 Supply and fixing of MCB 6 to 32 Amps, SPN, 240 Volt C series, breaking capacity 10 KA complete all as specified and as directed. 47 Supply and fixing of MCB 6 to 32 Amps, SP, 240 Volt C series, breaking capacity 10 KA complete all as specified and as directed.Note :- MCB and MCB DB being incorporated vide serial item No. 45 to 47 in the workshall be of same make. 48 Material and Labour for House service bracket (hook type complete with 3.0m long G.I. pipe 40mm dia Medium grade, two nos. 90 degree bends, M.S. hook and stay or guy complete all as specified and as directed. 49 Supply and fixing 1100 volts grade heavy duty cable PVC insulated aluminium stranded conductor of size 10 Sqmm, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular complete all as specified and as directed. 50 Materials and labour for earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 m below ground level connetced with galvanised wire of 4mm diaby means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe of 15mm bore (light grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (medium grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 m etc all as shown on electrical plate No. 3 of MES Schedule Part-I(2009) complete including testing on completion all as specified and as directed.Notes:-(i) Main earthing strip from earth plate electrode to rest point upto length of 7.5 meters length shall deemed to be included in the unit rate quoted against this item. (ii) On testing after completion if the desired resistenance is not obtained the contractor shall redo the earthing without any extra cost to the department. 51 Materials and labour for earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 m below ground level connetced with galvanised wire of 4mm diaby means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe of 15mm bore (light grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (medium grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 m etc all as shown on electrical plate No. 3 of MES Schedule Part-I(2009) complete including testing on completion including taking down old unserviciable earthing set all as specified and as directed.Notes:-(i) Main earthing strip from earth plate electrode to rest point upto length of 7.5 meters length shall deemed to be included in the unit rate quoted against this item. (ii) On testing after completion if the desired resistenance is not obtained the contractor shall redo the earthing without any extra cost to the department.
