Tender For Repair And Maintenance Of Movable Target Installed At A-Range And Guard Room At Stc Bsf Kharkan Camp Ei And Fans => Limited; 1 Earthwork in excavation by manual means up to a depth of 2m below the existing ground level for foundation trenches of foundations, footings of column/ walls, retaining walls, septic tank etc. including bailing out water where necessary and removal Of surplus earth with all lead and lifts as directed and specified for the following classification of soils.All kinds of soil (ordinary soil/ hard soil/ dense soil) 2 Supplying, fitting and fixing in position reinforcement bars up to lst floor level, conforming to relevant I.S. Code for R.C.C. work/ a.a. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20 G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (Rates inclusive of all wastage, lappage, hooks, chairs, anchorage etc. and no measurementfor the same is required)Thermo-Mechanically Treated bars 3 Centering and shuttering including strutting, propping etc. and removal of form for all heights complcte and as directed by Engineer in charge.Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc (using steel) 4 Lintels, beams, plinth beams, girders, bressumers and cantilevers (using steel). 5 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost Of centerjng, shuttering, finishing and reinforcement- All work up to plinth level:M20 or 1:11/2:3 (1 cement: 11/2 coarse sand: 3 graded stone aggregate 20 mm nominal size) 6 Reinforced cement concrete work in beams, slabs, roofs having slope up to 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to first flcor level, excluding the cost of centerlng, shuttering, finishing and reinforcementM20 or 1:11/2:3 (1 cement: 11/2 coarse sand: 3 graded stone aggregate 20 mm nominal size) 7 Providing soling with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete.Stone soling100 mm 8 Plain cement concrete works in foundation bed for footing steps, walls, brick works etc below plinth level as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately1 :3:6 (1 Cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size 9 Half brick masonry with common burnt clay (non modular) lst class bricks in superstructure above plinth level up to first floor levelCement mortar 1 :4 (1 cement: 4 coarse sand) 10 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections ………………. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing,and panelling to be paid for separatelyFor fixed portionPowder coated aluminium (minimum thickness Of powder coating 50 micron) 11 For shutters, doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing Of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separatelyPowder coated aluminium (minimum thickness Of powder coating 50 micron 12 Providing and fixing 12 mm thick pre-laminated particle board flat pressed three layer or graded wood particle board conforming to ls:12823 Grade-I Type-ll, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass/ stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-chargePre-laminated particle board with decorative lamination on both sides 13 Providing and fixing glazing in aluminium door. window, ventilator shutters and partitions etc. with EPDM rubber/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge:With float glass panes of 4.0 mm thickness (weight not less than 10 kg/sqm 14 Providing and fixing lsl marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per ls:1868) transparent or dyed to required colour or shade with necessary screws etc. complete:100x63x4 mm 15 Providing and fixing aluminium sliding door bolts, lsl marked anodised (anodic coating not less than grade AC 10 as per ls:1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete300x16 mm 16 Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with lsI, ls:3564, embossed on the body, door weight up to 35 kg and door width up to 700 mm), with necessary accessories and screws etc. complete. 17 Providing and fixing aluminium handles, lsl marked, anodised (anodic coating not less than grade AC 10 as per ls:1868) transparent or dyed to required coloilr or shade, with necessary screws etc. complete: 18 Providing and fixing aluminium tower bolts, Islmarked, anodised (anodic coating not less than grade AC 10 as per ls:1868) transparent or dyed to required colour or shade, with necessary screws etc. complete 19 Providing, fitting and fixing steel windows (includingventilators)ofstandardrolledsteelsectionsasperrelevantI.S.Code,jointsmitredandweldedwith15x3xl00mmlugsembeddedincement concreteblock ofM-10 gradeincludingprovidingandfixingofprojectinghinges(notmorethan65mm and not lessthan 15 mm wide) boltingdevice, steelhandles,pegs,stays of 300mmlongetc.completeincludingproviding12xl2mmsquarebarsduly weldedtosteelframeat not more than12 cm c/c applying a priming coat of red-leadpaint etc. complete as per drawingOpenable 20 Providing&fixingglasspaneswithputtyandglazingclipsinsteel doors, windows, clerestory windows, all complete with4.0mm thick glass panes 21 Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes up to 10 mm dia. etc. complete 22 Providing and fixing G.I. chain link fabric fencing Of required width in mesh size 50x50 mm includjng strengthening with 2 mm dia. wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-chargeMadeof G.I. wire ofdia. 4 mm 23 20 mm cement plaster of mix: 1 :4 (1 cement: 4 fine sand) 24 Cement mortar 1 :4 (1 cement: 4 fine sand). 25 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: 26 Wall painting with acrylic emulsion pain of approved brand and manufacture to give an even shade
