Special Repair To Bldg No T-121 At Cariappa Coy, Aec Trg College And Centre; 1 Demolition of PCC in ground floorand pavings not exc 15 cm thickness below or above ground level complete all as specified and directed. 2 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. 3 Taking down cement plaster on brick or stone wall surfaces including glazed tiles wherever exists including raking out joints, hacking for key and scrubbing down with water complete all as specified and as directed. 4 Demolition of brickwork or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins,arches, pillars,etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. 5 Taking down chowkhats or frames with shutters ( without taking off shutters from the frames) ofArea not exc 1.5 sqm each complete all as specified and directed. 6 Taking down chowkhats or frames with shutters ( without taking off shutters from the frames) of Area exc 1.5 sqm but not exc 4 sqm eachcomplete all as specified and directed. 7 Hacking out old broken glass (any thickness, size, quality or description) from wooden frames includingpunching or drilling out old glazing pins/spring clips complete all as specified and as directed. 8 Disconnecting and dismantling of Capacity exc 250 Ltr but not exc 500 Ltr water storage tank and removing from the site of following capacity of tank completeall as specified and as directed:- 9 Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed. 10 Dismantling of Plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed. 11 Material & labour for 75mm cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregate) as in Plinth Protection complete all as specified and directed. 12 M&L chequred cement concrete tiles 20cm X 20cm X 25mm thick, with grey cement and pigments, set, jointed and pointed in neat cement slurry in floors, over15mm thick cement screed beeding layer in cement mortar 1:4 complete all as specified and directed. 13 M&L for 25 mm thick PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate for floor finishes complete all as specified and directed. 14 M&L for vitrified light shade tiles in floor of size 600mmx600mmx10mm thick of approved colour laid over and including 15mm thick screed bed in CM 1:6 jointed and pointed with approved materialsas per manufacturers instructions complete all as specified and directed. 15 Material & labour Glazed ceramic White/light shade tilesin vertical surfaces riser of steps ,skirting, dado and pillarof size 350x250mmx7mm /450x350x7mm thickset and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in CM 1:4.complete all as specified and directed. 16 M&L Non Skid ceramic White/light shade tiles7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm,in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match 15mm thick screed bed in CM 1:6 complete all as specified and directed. 17 Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. 18 M&L for brick work with modular size full bricksubclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed. 19 Material & labour Brickwork with sub- class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in, built in CM 1:4 complete all as specified and directed. 20 Material & labour for 10 mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces, surfacesfinished even and smooth without using extra cement complete all as specified and directed. 21 Material & labour for 10 mm thick rendering on other than fair faces of brick work or concrete surfaces,inCM(1:4)surface finished even and smooth without using extra cement complete all as specified and directed. 22 Supply only integral water proofing compound complete all as specified and directed. 23 Material & labour for preparation of new plastered surfaces of walls etcand applying two coats of cement base paint over a coat of alkali resistant primercomplete all as specified & directed. 24 Material & labour for preparation of new plastered surfaces of walls with and applying 1mm thick cement base putty Birla Wall Care Putty or equivalentapprovedspeficied make on plastered surfaces including preparation of surfaces and applying two coats of Oil bound distemper to match the existing surfaces as required, complete all as specified & directed. 25 Material & labour for Complete removal of existing treatment on old surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primercomplete all as specified & directed. 26 Material & labour for Complete removal of existing treatmenton old surfaces of walls with applying 1mm thick cement base putty Birla Wall Care Putty or equivalentapprovedspeficied make on plastered surfaces including preparation of surfaces and applying two coats of Oil bound distemper to match the existing surfaces as required, complete all as specified & directed. 27 M&L for PCC (1:3:6) type C-1, using 40mm graded stone aggregate as in surface channel and drain including saucer drain and toe wall etc complete all as specified and directed. 28 Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including finishing the top of benching even and smooth using extra cementcomplete all as specified and directed. 29 M&L for suspended false ceilling comprising of 6mm thick non asbestos fibre cement bulding boards fixed or laid/inserted to GI frame work with screws over Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified 30 M/L 75 mm thick cement concrete 1:4:8 type D-2 using (40 mm graded stone agg) as in sub base complete all as specified and directed. 31 S&F second class hard wood (Sal) plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed. 32 M&L Pre- painted galvatume aluminum zinc coating GI based corrugated steelsheet 0.50mm thick of ancolour having tensile strength of 550 Mpa as in roof covering/ cladding towall, fixed with self tap ping screws as specified . 33 S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in ridges, roof covering/ clading to wall, fixed with self tapping screws, complete all as specified & directed. 34 S&F rolled mild steel section Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or otherconnecting plates Fe-290(Gde 165) complete all as specified & directed. 35 S & F rolled mild steelplates ( plain on chequered) channels, square cutor notched (ordinary and counter sunk) forming holes without any attachment conforming to Fe-290(Gde 165)quality ‘A’ complete all as specified & directed 36 Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earthor broken rubble mixed withearth around, in layers not exceeding 25 cm, getting out in hard / dencesoil. 37 M&L PCC 1:3:6 type C-2 using 40 mm graded stone aggregate,Cement concrete in foundations, filling and massconcrete all as specified and direcetd. 38 S&FBands,FI straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: conforming to Fe-290 Gde-E-165 all as specified and directed. 39 Supply only Chain link MS galvanisd fencing, anysize all as specified and direcetd. 40 Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire all as specified and direcetd. 41 M&L for10mm dia round bar as in streghthening bar in fencing all as specified and direcetd. 42 S&F Solid PVC Door Frame of size 50 mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specified and as directed. 43 Supply & fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame, made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC , ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for to rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed to getter with solvent cement, supplying & fixing in the frame at site as per specification & drawing on page No 171 of SSR 2009 (Part-I) complete all as specified and directed. . 44 S&F as in repair vitreous china wash downwater closet pan (pedestal pattern), white (flushing cistern and flush pipe) fixed with ‘P’ or ‘S’ trap, including making good the disturbed surfaces and to match with existing surface complete all as specified and directed. 45 Supply & fix white plastic seat cover for W.C.(E.T.) white including M.S. CP or aluminium hinging device complete all as specified and directed. 46 S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified & directed. 47 S&F 600mmx450mm fancy type bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified & directed. 48 S&F in repair Brass chromium plated shower rose 125mm size Complete all as specified and directed. 49 S&F Tubular towel rail 20mm dia alu. anodised, D type, 60cm long between flanges complete all as specified and directed. 50 S&F as in repair Vitreous China wash basin, white, flat back, size 550 x 400 mm, including fixing acessories like galvanised brackets & rag bolts,32 mm CP waste coupling complete all as specified. 51 S&F in repairPVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. 52 S&F in repair PVC(SWR)bends 110mm bore provided with access door, any radius complete all as specified & directed. 53 Supply & fix in repair pillar tapscast copper alloy with capstan heads, chromium plated, screwed down, high pressure with or without lettered “hot” or “cold” with long screwed shanks and fly nut screwed for iron pipe of 15mm bore,complete all as specified & directed. 54 Supply & fix in PVC connections of 450mm long of PRYAG Make suitable for 15mm dia iron pipe including PTMT nuts complete all as specified & directed. 55 S&F in repair PVC valveless, symphonic action type low level flushing cistern white with inlet ball valve, float and handle including brackets, 10 ltr capacity complete with flush pipe(Long bend) 32mm dia of make as approvrd by GE complete all as specified & directed. 56 Welded steel wire fabric Weight per square metre not exc 4 kg supplied and fixed to wood or steel members complete all as specified & directed. 57 Supply & fixin repairbib taps cast copper alloychromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe of 15mm bore, complete all as specified & directed. 58 Supply & fixin repair angular valve, 15 mm dia, cast copper alloy, chromium plated, screwed down, high pressure screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified & directed. 59 Supply and fixing PVC waste pipes of 40/32mm bore suitable for wash hand basins/sinks/urinals complete all as specified & directed. 60 Taking up or down 15mm bore steel water tubing (GI Pipe) and connections of following bore complete all as specified and as directed. 61 Taking up or down 20mm bore steel water tubing (GI Pipe) and connections of following bore complete all as specified and as directed. 62 Supply, fix 15mm bore, tubes medium grade, galvanized with all fittings and fixed to walls and ceiling or laid in floors including testing complete all as specified & directed. 63 Supply, fix 20 mm bore, tubes medium grade, galvanized with all fittings and fixed to walls and ceiling or laid in floors including testing complete all as specified & directed. 64 Supply & fix Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staplescomplete all as specified & directed. 65 S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty /wooden beads in square n. exc 0.5 sqm in each pane complete all as specified and as directed. 66 S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty /wooden beads in squareexc 0.5 sqm in each pane complete all as specified and as directed. 67 Supply & fix butt hinges, 100 mm long of stainless steel,complete all as specified & directed. 68 Supply & fix mild steelworkas in hold fast etc and similar articles confirming Fe-310-0 with & including material & labour tarring & sanding complete all as specified & directed. 69 Supply & fix 125mm size aluminium alloy handles cast type anodized complete all as specified & directed. 70 S&F aluminium tower bolts 150mm long, of extruded section complete all as specified and directed. . 71 Supply & fix Aluminium. Sliding door bolts, plate type,complete, 250mm long complete all as specified and directed. 72 S&F Anodised Powder Coated aluminium door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc. complete all as specified. 73 S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge. 74 M&L Aluminium powder coated (powder coated of requried colour) three track sliding windows frame top & sides of size 92x31.75x1.50 mm (section No 20831), bottom size 92x31.75x1.50mm (section No 20832) and shutter top & bottom of size 40x18x1.55mm (section No 20736) and sides (handle) of size 40x18x1.55mm (section No 20738) and lock side shutter frame of size 40x18x1.45mm (section No 20737) with including and fixing rubber gasket, beading and locking arrangement including making good to the disturbed portion complete including & fixing stainiess steel wire mesh 0.36mm nominal dia of wire with 1.40mm average aperture and fixed with stainless steel wire staples and including and fixing 5mm thick glass with necessary rubber beading gasket etc including necessary plaster, painting, cill and making good to disturbed portion all as specified and as directed by Engr-in-charge. 75 M&L preparation of oldwooden surfaces of any description, not other wise described over 10cm width or girth and apply two coat of synthetic enamelpaint complete all as specified and directed. 76 M&L preparation of Previously untreatedwooden surfaces of any description, not other wise described over 10cm width or girth and apply two coat of synthetic enamelpaintover one coat of pink primer complete all as specified and directed. 77 M&L for preparation of old painted steel surfaces of any description over 10 cm width and grith and applying one coat of synthetic enamel paint complete all as specified and directed. 78 M&L preparation of new steelsurface and applying two coats of synthetic enameled paint over a primming coat of red oxide etc complete all as specified and as directed. 79 Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing etc., and making good, cutting exc 10 cm but not exc 20 cm girth all as specified. 80 Supply & fix mild steel framed work such as grills, gratings guard bar etc with ends of bars shouldered and/ or riveted etc completed all as specified. 81 M&L PCC type B-1, 1:2:4 (using 20mm graded aggregate) as in coping ,benching, haunching including all necessary form work complete all as specified and directed.
