Tender For Under District Barabanki, Renovation Work At Kasturba Gandhi Residential School, Block Puredalai - Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. DSR 15.56 3 E/W in excavation by mechanical means (Hydraulic Excavatory)/manual means in foundation trenches or drain (Not exceeding 1.5m in width or 10 sqm on plan). I/c dressing of sides and ramming of bottoms, for all lift, i/c getting out the excavated soil and disposal of surpluse excavated soil as directed, within a lead of 50 m. DSR 2.8 4 Providing and layingin position inC.C specified grade excluding the cost of centering, shuttering ,finishing and reinforcement ( 1:6:12)with cement , Fine sand and 40mm gauge B/ ballast i/c all as per pwd spacifications no 273 5 Brick work with common bruint clay F.P.S. (Non Modular) Brick of class designation 7.5 in foundation and plinth in cement mortar 1:6 (1 Cement ; 6 coarse sand) DAR NO. 6.1.2) 6 Brick work with common bruint clay F.P.S. (Non Modular) Brick of class designation 7.5 in supper structure above plinth up to floor v level in all shapes and sizes cement mortar 1:6 (1 Cement ; 6 coarse sand) DAR NO. 6.4.2 7 Providing and laying in position specified grade of reainforced cement concrete excluding the cost of centering and shutteringand finishing rainforment in 1:2:4 (1 cement:2 coarse Sand Zone-III) derived from natural sources :4 graded stone aggregate 20 mm nominal size derived from naturela sources in Plinth Beam. DAR 5.1.3 8 Centering and shuttering i/c strutting, propping etc and removal of form forLintels, beams, plinth beams, girders, bressumers and centilevers.. DSR No. 5.9.5 9 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) 5.2.2 10 Centering and shuttering including strutting, propping etc. and removal of form for :Columns, Pillars, Piers, Abutments, Posts and Struts DSR 5.9.6 11 Structural steel work riveted, bolted or welded in built up sections, truesses and framed work. i/c cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. DSR 10.2 12 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) DSR 5.1.2 13 Centering and shuttering including strutting, propping etc. and removal of form for :Foundations, footings, bases of columns, etc. for mass concreteDSR 5.9.1 14 Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.1.00 mm thick with zinc coating not less than 275 gm/m*DSR 12.1.1 15 Providing and fixing 35 mm thick shutterspanelled or panelled and glazed shutters for doors. Windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of engineer-in-charge. (Note Butt hinges and necessary screws shall be paid seprately) DSR 9.5.10 16 12 mm thick Cement plaster in 1:3 cementcoarse sand finished with a floating coat of neat cement. DSR 13.9.1 17 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate. DSR 11.3.1 18 Excavating, supplying, stacking and filling of local earth (i/c royalty) by mechanical transport upto a lead of 5km also i/c remming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinths, sides of foundation etc. complete for all lift. DAR No. 2.25(a) 19 Providing & applying white cement based putty of aveage thickness 1mm of approved brand and manufacturer ove the plastered wall surface to prepare the surface even and smooth complete SI No DSR 13.80 20 Distempering with 1st quality acrylic distemper (Ready Mixed) VOC content less tha 50 gm/ltr. Of approved manufacturer and of required shade and colour all complete to achieve even shade and colour. New work (Two or more coats) over and including water thinnable priming coat with cemnt primer having VOC content less than 500 gram/Ltr. DSR 13.41.1 21 Painting with synthetic Enamel paint of approved brand and manufacture of required colour to give and even shade, Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture DSR 13.62.1 22 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to LS: 15622 of approved make in all colours and 11.41 shades, laid on of 20mm thik cement mortar 1:4 (1 cement :4 coarse sand ), jointing with grey cement slurry @3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. size of tile 600x600 mm. DSR Code 11.41.2 23 Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete. (Floor Tiles) DSR 14.40 24 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (Wall Tiles)DSR 8.31 25 Providing and fixing water closet squatting pan (Indian type W.C. pan of size 580×440mm with ingegral type foot rests ) with 100 mm sand cast Iron P or Strap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required Same as above but for Indian type W.C. pan DSR 17.1.1 26 Providingandfixingwash basinwith C.I.brackets, 15 mm C.P. brasspillartaps, 32mmC.P. brasswasteofstandardpattern, includingpaintingoffittingsandbrackets,cuttingandmaking good the walls wherever require a)White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tappillar tap.(DSR 17.7.4) 27 Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C. brackets and stainless steel plug 40 mm, including painting of fillings and brackets, cutting and making good the walls wherever required Kitchen sink with drain board of size 51Ox1040x200mm DSR 17.10.1.1 28 Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete. Flexible Pipe 32 mm dia DSR17.28.2.1 29 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. DSR 17.31 30 Providing & fixing 60x2cm. C.P. brass towelrail complete with C.P. brass brackets fixed to wooden cleats with C.P. brass screw. ESSCO AEC-1111 DSR 17.73.2 31 Providing & fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. DSR 18.51.1 32 13 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 40 mm nominal outer dia Pipes DSR 18.7.4 33 13 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 25 mm nominal outer dia Pipes DSR 18.7.3 34 Providing and fixing gun metal gate valve with wheel of approved quality. 25 mm nominal bore DSR 18.7.1 35 Providing and fixing gun metal gate valve with wheel of approved quality. 40 mm nominal bore DSR 18.7.2 36 24 Providing and placing on terrace (at all floor levels) polyethylene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for circular tank. DSR 18.48 37 Point wiring in PVC conduit, with piano type switch :-Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLSPVCinsulatedcopper conductor singlecore cable insurface / recessedmediumclasspvc conduit, with mdulartype switch, modularplate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulatedcopperconductorsinglecorecableetc. as required. DSR1.10.3 (Ele 2022) 38 Power plug wiring in PVC conduit (2 x 4 Sq.Mm.):Wiringforlight/powerplugwith2X4sq.mmFRLSPVC insulated copperconductor single core cable insurface/ recessed medium class pvc conduit alongwith1 No. 4sq mmFRLSPVCinsulatedcopperconductorsinglecorecable for loop earthing as required. DSR 1.12 39 Power plug wiring in PVC conduit (4 x 4 Sq.Mm.):-Wiringforlight/powerplugwith4X4sq.mmFRLSPVC insulated copperconductor single core cable insurface/ recessedmediumclasspvc conduit alongwith 2 Nos. 4 sq. mmFRLSPVCinsulatedcopperconductorsinglecorecable for loop earthing as required.DSR 1.13 40 Circuit/ Sub main wiring in PVC conduit:-Wiringforcircuit/ submainwiringalongwithearthwire with the following sizes of FRLSPVC insulated copper conductor,singlecorecablein surface/ recessedmedium class pvc conduit as required. 41 2 X 1.5 sq. mm+1 X 1.5 sq. mm earth wire. DSR 1.14.1 42 2 X 2.5 sq. mm+1 X 2.5 sq. mm earth wire. DSR 1.14.2 43 2 x 6 sq.mm.+ 1 x 6 sq.mm. Earth wire DSR 1.14.4 44 S/F power plug point piano type accessories:-Supplying and fixing metal boxof 180 mmX 100 mm X60 mm deep (nominal size) on surface or in recess with suitable sizeof phenoliclaminatedsheetcoverin frontincluding providing and fixing 6 pin 5/6A & 15/16 A socket outlet and 15/16Apianotypeswitch,connections,paintingetc.as required. DSR 1.30 45 Applying and fixing 20 amps, 240 volts, SPN, industrial type socketoutlet,with2polesandearthmetalenclosed plug topalong with20 amps.Ccurve,SPMCBinsheetsteel enclosure, on surface or in recess, with chainedmetal cover for the socket outlet, and complete with connections, testing andcommissioning etc. as required. DSR 2.18 46 S/F modular type electronic fan regulator:-Supply and fixing twomodule stepped type electronic fan regulator on theexistingmodular plateswitchbox includingconnectionsbut excludingmodularplateetc.As required. DSR 1.25 47 S/F modular type blanking plate :-Supplyandfixingmodularblankingplateontheexisting modular plate &switch boxexcluding modular plateas required. DSR 1.26 48 Supplyandfixing of followingsizesofmediumclassPVC conduitalongwith accessories insurface/recessincluding cutting the wall and makinggood thesameincaseof recessed conduit as required: DSR 1.21 49 20 mm DSR 1.21.1 50 25 mm DSR 1.21.2 51 Supplyingandfixing5amps.to 32amps. rating,240volts C series,miniature circuitbreaker (MCB) suitable for inductiveload offollowingpolesin theexisting MCB DB completewith connections,testing andcommissioning etc. as required. single pole DSR21.2.10 52 Supplying & fixing singlepole, blankingplate inthe existing MCBDBcomplete etc. as required. DSR 2.11 53 S/F DP MCB IsolatorSupplyingandfixingfollowingrating,doublepole, 240V, isolatorintheexisting MCBDBcompletewith connections, testing and commissioning etc. DSR 2.12 54 40 Amp DSR 2.12.1 55 63 Amp DSR 2.12.2 56 Supplyingand fixing following rating,fourpole, (three phase&neutral)415 volts, residual current circuitbreaker (RCCB),havingasensivitycurrentupto300miliamperes in theexisting MCBDBcompletewith connections,testing and commissioning etc. as required: 63 Amps. DSR 2.15.3 57 Supplying and fixing followingway, SP&N, sheet steel,MCB distribution board, 240Vonsurface/ recess, completewith tinnedcopperbusbar,neutralbusbar,earthbar,dinbar, interconnections,powderpainted including earthing etc. as required. (But without MCB /RCCB /Isolator) 6 way, Double door DSR 2.3.1 58 Supplyingandfixingfollowing way,horizontaltype TP&N,sheetsteel MCB distribution board,415 Von surface /recess,completewithtinned copper busbar, neutral bus bar, earth bar, din bar, interconnections, powder paintedincluding earthingetc.asrequired(But without MCB / RCCB / Isolators). 4 way (4 + 12), Double door DSR 2.4.1 59 Installation,testingandcommissioningof ceilingfan includingwiringthedownrodofstandardlength(upto30 cm.) with 1.5 sq. mm. FRLS PVC insulated, copper conductor, singlecorecable,includingprovidingand fixingphenolic laminated sheet cover on the fan box etc. as required. DSR 1.45 60 Installationofexhaustfaninthe existingopening, including makinggoodthedamage, connection, testing, commissioning etc. as required Upto 450 mm sweep. DSR 1.50.1 61 Supply, Installation, Testing and Commissioningof 1200 mm sweep,BEE5 starrated,ceilingfanwithBrushLessDirect Current(BLDC)Motor,classofinsulation:B,3nos.blades, 30cmlongdownrod,2nos.canopies,shacklekit,safety rope,copperwinding, Power Factornot less than 0. Service Value (CMM/W)minimum6.85,Airdelivery minimum215CMM,350RPM(toleranceasperIS:374- 2019), THD less than 10%, remote or electronic regulatorunitforspeed controlandallremaining accessoriesincludingsafetypin,nutbolts,washers, temperaturerise=75degreeC (max.), insulationresistance morethan 2 megaohm,suitablefor230V,50Hz,single phase AC Supply, earthing etc. complete as required. DSR 19.1 62 SupplyofLEDTubeLightwithMetalheavydutyBoxtype battenLightfitting1X22wattsuitableforupto1X22watt LED Polycarbonate tube light complete Including tube suitable for both surface & suspended complete in all respect. UPSOR Ch.14, 1413, CAT-AAA 63 Design, Supply, Installation, Commissioning and five years warranty with solar street lighting white LED system 12W, Li-Fe PO4 Battery 12.8V 30A.H. , 75Wp solar PV module, 6 mtr. G.I. Pole Inclusive of all taxes. With Sign Board 64 S/F Inaugration black granite (Polished) 20mm thick stone size 0.90x0.75m. including lettering, printing, border etc. will be painted of superior quality is required shade and colour including fixing excavation of foundation (1.40x0.50x0.40 m), P.C.C. 1:6:12 (1.40x0.50x0.10m), brick work 1:4 cement coarse sand foundation (1.40x0.345x 0.30m) ,upto (1.40x0.23x1.35 m),12mm thick plaster 1:4 cement coarse sand and finishing walls with water proffing white cement paint of approved make and quality such as super snowcem paint etc. all complete.
