Tender For Special Repair Of Building No T-32 At Ramban Under Age (I) Bhalra; 1 Dismantling asbestoes cement (corrugated or semicorrugated etc) sheets in roof covering. 2 Dismantling timber scantling 40 Sq cm and over in section framed work of any description. 3 Dismantling wooden framed trusses of span n.exc 10m. 4 Demolition of stone masonry work built in cement mortar or cement lime mortar incl all quoins, arches pillars etc and removing unserviceable material exc 100mtr complete all as specifieda and directed. 5 Dismantling boarding any description fixed in any position with nails including GI frame work complete all as specified and directed. 6 Taking down cement plaster of any description on brick or stone walls or from concrete surface incl racking out joints hacking for key scrubbing with water etc complete all as specified and directed. 7 Taking down chowkats or frames with shutter w/o taking off shutter from the frame n.exc 1.5 Sqm each incl cutting holes for taking out hold fast or dismantling brick (holes cut and any other damage to jambs, wall for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt) complete all as specified and directed. 8 Taking down chowkats or frames with shutter w/o taking off shutter from the frame exc 1.5 Sqm but n.exc 4 Sqm each incl cutting holes for taking out hold fast or dismantling brick (holes cut and any other damage to jambs, wall for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt) complete all as specified and directed. 9 Dismantling floors hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises. 10 Dismantling stone slabs and tiles of any description or thickness in floors laid bedded and pointed in any mortar. 11 Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15 cm thickness (below or above ground level) and removing unserviceable material exc 100 mtr as specified. 12 M&L reinforced cement concrete (nominal mix) in Type B1 1:2:4 (20mm graded crushed stone aggregate) Beams, cantilevers, bressummers, lintels over 1.5m span as in lintel band complete all as specified and directed. 13 M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, lintels, cantilevers, shelves including supports, overhangs etc also splays between floors and beams etc as specified and directed. 14 M&L for steel reinforcement TMT bars 10mm dia and over cut to length, bent to shape and tying with annealed MS wire 0.9mm dia complete all as specified and directed. 15 All as per item No 14 here-in-before but 5mm dia and over upto and incl 10mm dia as in binders, stirrups, spacer all as specified and directed. 16 S&F for structural steel works of Fe 410W (Gde E 250) quality A, as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel) or flat sections) including distance pieces, cleats etc including painting one shop coat of zinc chromate/red oxide primer paint (including preparation of surface) before fabrication complete all as specified and directed. 17 S&F plates Fe-410-W (Gde-E 250) quality B (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed. 18 M&L for mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 22.5cm and n.exc 30cm long, Diameter of neck 16mm to 20mm complete all as specified and directed. 19 Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. 20 Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified directed. 21 M&L walling of polygonal rubble, uncoursed, well bonded, bedded solidly hearted built in CM 1:6 complete all as specified and directed. 22 All as per Ser No 21 here-in-before but except stones. 23 S&F pressed steel frames for door (Factory made) out of 1.25mm thick black MS sheet, with one or more rebates including necessary fixing lugs, butt hinges, lock strike plate, etc complete, size of frame 105x60mm incl bottom of each chowkat to be welded with 02 Nos 25x25x3mm thick flat iron projecting 10cm on either side and back fill to chowkats with PCC 1:3:6 type C0 using 12.5mm graded crushed stone aggregate including one shop coat of red oxide primer complete all as specified and directed.Note : PCC 1:3:6 type C-O as in backfill will be paid separately. 24 S&F pressed steel frames for door (Factory made) out of 1.25mm thick black MS sheet, with one or more rebates including necessary fixing lugs, butt hinges, lock strike plate, etc complete, size of frame 125x60mm incl bottom of each chowkat to be welded with 02 Nos 25x25x3mm thick flat iron projecting 10cm on either side and back fill to chowkats with PCC 1:3:6 type C0 using 12.5mm graded crushed stone aggregate including one shop coat of red oxide primer complete all as specified and directed.Note : PCC 1:3:6 type C-O as in backfill will be paid separately. 25 M&L cement concrete 1:3:6 type C-O using 12.5mm graded stone aggregate as in backfill of pressed steel door frames complete all as specified and directed by the Engr-in-Charge. 26 M&L for PCC 1:2:4 type B1 using (20mm graded aggregate) as in blocks for hold fasts, benching, coping apex stones, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork all as specified and directed. 27 M&L for coloured non skid ceramic tiles 7 to 8mm thick, area of each tile exc 0.11 Sqm but n.exc 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match shade, pattern, laying etc of tiles, over and incl 15mm thick screed bed or bedding layers of cement mortar 1:6 complete all as specified and directed. 28 M&L glazed ceramic coloured tiles (premier quality) of size 450x350x7mm thick on vertical surfaces such as skirting, dados and risers to steps etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces over and including 10mm thick rendering in CM 1:4 all as specified and directed.Note : Design, shape and pattern of fixing of tiles shall be as directed by Engr-in-Charge. 29 M&L for machine cut kota stone slab flooring 20-25mm thick laid over and including cement screed base 15mm thick in cement mortar 1:6, including cutting as required, rubbing and polishing to granite finish over complete all as specified and directed. 30 M&L for machine cut kota stone slab (single piece) 20-25mm thick as in riser of steps, skirting, dado and pillar liad over and including rendering of 10mm thick in cement mortar 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting as required, rubbing and polishing to granite finish complete all as specified and directed. 31 S&F 35mm thick factory made 2nd class hard wood plain framed, panelled shutter (two panel) of factory made with lock rail and panel of 12mm thick veneered particle board with commercial veneering on both faces including wooden beads on both sides, one coat of pink primer.The size of rail and stile as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated. 32 S&F 35mm thick factory made 2nd class hard wood factory made glazed and skelton shutters open rebated and prepared to receive glass/wire gauge etc without sash bar but with lock rail edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass/wire mesh etc sizes of member as per clause 8.20(a) of SSR Part-I for door shutter complete all as specified and directed. 33 M&L for preparation of new wood or wood based surface and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed. 34 S&F aluminium handle cast type, anodised size 150mm long. 35 S&F aluminium anodised barrel tower bolts, with bright bolt and fixed 200mm. 36 S&F 300mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed. 37 S&F Helical door spring 300mm including roller and roller plate complete fixed with welding to existing steel chowkats all as specified and directed. 38 S&F box type steel windows/ventilator (factory made) outer frame made out ERW tube P section 65x45x25mm and shutter of ERW tube P section 50mmx35mmx20mm openable (double shutter) with glazed shutter on external side and gauzed shutter on internal side including steel pintel hinges steel handle 100mm long mild steel tower bolt 02 Nos on each shutter stopper of Z section and its locking arrangement and mild steel hook and eyes suitable for fixing cooler/AC window complete all as specified and shown on drgs No CEPZTD-324/07 Sh 1/3 to 3/3.Note : The quoted rate shall also include :- (i) One shop coat of zinc chromate primer on all exposed surface and one coat of tar on the ends of steel surface in contact with bricks/concrete surface.(ii) 04 Nos MS steel lugs made of 20x5mm Iron flat 200mm long(iii) 10mm Sq Bar grill/guard bar design as per drawing(iv) PCC block for embedding lugs. 39 M&L preparation of new surfaces of steel of any description exc 10cm width or girth and applying two coats of synthetic enamel paint any tint over of coat of red oxide primer complete all as specified and directed. 40 S&F 3mm thick sheet glass ordinary quality glazing with steel pins, oil putty to steel windows and beads nails etc to wooden surfaces as in square as in square n.exc 0.50 Sqm in each pane all as specified. 41 S&F galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tackes or galvanised wire staples. 42 M&L for rendering 15mm thick cement plaster in cement mortar (1:6) on stone masonry work or concrete surfaces of wall and to be finished even and smooth without using extra cement all as specified. 43 M&L for rendering 15mm thick cement plaster in cement mortar (1:4) on stone masonry work or concrete surfaces of wall and to be finished even and smooth without using extra cement all as specified (incl all necessary scaffolding, lifting arrangement). 44 M&L for two coats of oil bound distemper of wall to newly plastered surfaces including preparation of surfaces complete all as specified and directed. 45 M&L for one coat of oil bound distemper to old treated surfaces including preparation of surfaces complete all as specified and directed. 46 M&L for two coat of cement based pain including preparation of new surfaces of walls including primer complete all as specified and directed by Engr-in-Charge. 47 Preparation of old plastered surface including filling of small holes etc and applying one coat of cement based paint complete all a specified and directed by Engr-in-Charge. 48 S&F 4mm thick of size 605x605mm, white pre-premiered, self embossed, reinforced designer board for false ceiling conforming to IS-14862 and ISO-8336:1993 comprising as under : (i) GI section frame work (Powder Coat) for white, pre-premiered, self embossed, reinforced designer board consisting of perimeter wall angle 19mmx19mmx0.45mm, cross Tee 28.6mm (web) x 24mm flange.33mm thick powdered coated main tee 38 (web)x24mm flange 0.33mm thick wall angle screwed fixed to brick wall/partition wall/concrete/RCC with the help of nylon sleeves and screws @610mm C/C, then suspending GI main Tee in both directions by means of hangers with alignment @1220mm C/C to soffits.To from grid of 610x610mm cross Tee shall be provided @610mm C/C in both directions.Note : Suitable provisions shall be made for fixing the recessed/surface mounting light fittings if any, complete all as specified and directed by Engr-in-Charge. 49 M&L for one coat of synthetic enamel paint tint after preparation of old surfaces of steel of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different unit. 50 M&L 75mm thick PCC type C2 1:3:6 (40mm graded aggregate) as in plinth protection filled with mastic filling and 10mm wide joints between the walls and plinth protection shall be filled with mastic filling complete all as specified. 51 S&F stainless steel drapery rods of 25mm dia complete with coloured conical end balls at both end, dia not less than 50mm and fitted with and incl MS bracket size 150mm made to shape or 75mm dia MS end wall to wall round block made to shape in mae and female pieces as required at site. 52 Taking up or down steel tubing and connections, including cleaning for re-fixing 15mm bore of pipe. 53 S&F GI pipe, medium grade, galvanised, with all fittings and fixed in short lengths complete to walls and ceilings or laid in floor, 15mm bore of pipe. 54 All as per item No 53 here-in-before but fixing only. 55 Taking up or down steel tubing and connections, including cleaning for re-fixing 20mm bore of pipe. 56 S&F GI pipe, medium grade, galvanised, with all fittings and fixed in short lengths complete to walls and ceilings or laid in floor, 20mm bore of pipe. 57 All as per Srl item No 56 here-in-before but fixing only (20mm bore of pipe). 58 Dismantling water tanks and removing to store exc 1000 & n.exc 2000 litres. 59 S&F in repairs Rotational moulded polyethylene water storage tank three layer white in colour (Cylindrical vertical with closed top) hoisted and fixed in position of capacity 2000 Ltrs including ball valve 20mm dia high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (Minimum weight 210 gms) complete all as specified in SSR Part-I and directed by Engr-in-Charge. 60 S&F in repair 15mm bore bib taps, fancy type chromium plated cast copper alloy with crutch or butterfly handle, screwed for iron pipe or for brass ferrule. 61 S&F in repair15mm bore stop/angle valves, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union. 62 Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, (fittings such as switches, ceiling roses, pendants,regulators, sockets, MCBs,DB etc. to be measured separately), removing materials to store for kepping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surface of walls, floors, etc. all as specified and directed. 63 M&L point wiring in casing caping/PVC conduit (not less 20 mm) on sufraces of wall/ceiling floor etc complete with PVC insulated and unsheathedFRLS cable of 1.5 sqmm (nominal area) with multistranded copper conductor single core 1100 volts grade in and includingPVC conduit/casing & caping of suitable size, with PVC ploycabonate heavy duty terminal box, surface mounted PVC modular gang boxes (01 to 16 Module) and white cover plate with frame for mouting of Modular Switch/socket (1 to 16 Module) and as per site requirement and including 1.5 sqmm multistranded copper conductor cable of green colour as continuous earth wire with lugs and accesseries and making good disturbed surfaces of walls/floor etccomplete all as specified and as directed for the followings :- (Note :- Switch, socket and fan regulator shall be measure and paid separately under relevant items) 64 All as per Srl item No 63 here-in-before but for one 3 pin socket outlet 5 Amp on same board, complete all as specified and as directed. 65 All as per Srl item No 63 here-in-before but for one 3 pin socket outlet 5 Amp independent, complete all as specified and as directed. 66 All as per Srl item No 63 here-in-before but for one 3 pin socket outlet 15 Amp independent board with cable of size 2.5 Sqmm with 2.5 Sqmm copper conductor in green colour for earth continuity conductor, complete all as specified and as directed. 67 S&F Modular switch 6 Amp 1 module single pole one way complete all as specified and directed by Engr-in-charge. 68 S & F Modular Socketoutlet2 in 1, 3 pin 6 Amp 2 module flush type complete all as specified. 69 S&F for Modular switch 16 Amp 2 module single pole one way complete all as specified and directed by Engr-in-charge.. 70 M&L Modular socket , 5 pin, 6 and 16 Amp 2 module flush type universal complete all as specified and directed by Engr-in-charge. 71 M&L S & F stepped type electronic fan regulator on the existing phenolic laminated sheet etc. as reqd. modular flush type universal and all as specified and directed by Engr-in-charge. 72 Supply and fixing in repair LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as directed by Engr-in-Charge 73 S & F in repair LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size all as specified and directed. 74 M&L Ceiling rose surface bakelite three terminals complete and making necessary connections with suitable size flexible cable all as specified and directed by Engr-in-charge. 75 Supply and fix in repair exhaust fan Heavy duty (Industrial type), steel body AC single Phase. 230V of size 450m sweep with, blades, and frame and louvers as specified and directed. (Old fan shall be deposited to MES store yard) 76 Supply and fixing TPN DBs 8 way vertical type 415 V, factory made IP 43 protection class metal double door with 200 Amps rating Bus Bar 240/230 Volts, Neutal link, earth bar and Din Rail, provn for fixing of 01 No MCCB 100 Amps as incomer and fixing of MCB/iSOLATOR/RCCB etc complete all as specified and directed by Engr-in-charge. 77 Supply and fixing in repair MCCB 125 Amps, 3 Pole, 16 KA, fixed type, suitable to be fixed in 4way TPN DB complete all as specified and directed. 78 S & F MCB DB double doorSPN 16 Way with 200 Amps rated copper bus bar 79 S & F MCB DB double doorSPN 6 Way with 200 Amps rated copper bus bar 80 S & F MCB DB double doorSPN 4 Way with 200 Amps rated copper bus bar 81 Supply and fixing 5-32 amp MCB SP rating 240V, 10KA C curve miniature circuit breaker (MCB) in the MCB DB complete with connection testing and commissioning complete all as specified and directed by Engr-in-charge. 82 Supply and fixing 63 amp MCB SP rating 240V, 10KA C curve miniature circuit breaker (MCB) in the MCB DB complete with connection testing and commissioningcomplete all as specified and directed by Engr-in-charge. 83 Supply and fixing 40A to 63A MCB SPN amp rating 240V, 10KA C curve miniature circuit breaker (MCB) in the MCB DB complete with connection testing and commissioning including taking down all as specified and directed by Engr-in-charge. 84 Supply amd fixing TPN 40 Amps 415 V, 10 KA, C Series, curve miniature circuit breaker (MCB)in the DB complete all as specified and directed by Engr-in-charge 85 S & F in repair sub main wiring for circuit of size 6 sq mm 2 core (FRLS) alongwith earth wire of 6 sq mm single core of FRLS PVC insulated unsheathed cable,1100 volts grade with multistranded copper conductor including PVC conduit/casing capingof suitable size complete all as specified and directed by Engr-in-Charge. 86 S & F in repair sub main wiring for circuit of size 6 sq mm 4 core (FRLS) alongwith earth wire of 2 x 4.0 sq mm single core of FRLS PVC insulated unsheathed cable,1100 volts grade with multistranded copper conductor including PVC conduit/casing caping of suitable size complete all as specified and directed by Engr-in-Charge. 87 Supply and laying and testing in repair cable XLPE insulated, screned, PVC bedded galvanized steel strip or wire amoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 sq mm 4 core (from TPN DB to 4 way TPN box) Note :- Cable shall pass through wall/over false ceiling with support of truss with suitable size of GI saddles not more than 50 cm apart. 88 M&L for earthing mild steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25m deep below normal ground level) connected to galvanised earth lead wire 4.0 mm diaby means of galvanised iron nuts, bolts and washer, earth lead connected to eqpt as directed, earth plate surrounded with adequate quantity of charcoal dust mixed with common salt to a packed thickness of 15 cm all around the plate including necessary earth work, PCC chamber and reinforced PCC cover made by PCC 1:3:6 type C-1 as in pit chamber and RCC pit cover 50 mm thick precast RCC 1:2:4 type B-1 duly reinforced with 6mm dia MS bar at 150mm c/c both ways with 10 mm dia MS round bar as handle, 20 mm bore GI pipe medium grade for watering and 15 mm dia GI pipe light grade for protection of earth lead up to 7.5 mtr with funnel, wire mesh etc with and including testing complete all as specified and as shown in electrical plate No 3 of MES SSR Part I. 89 S & F in replacement enviroment friendly recess/pendent mounting LED flat panel 36 Watts, 6500K,2x2 LED panel fabricated CRCA sheet steel housing cool white with high efficient LEDs & glare free opal diffuser PF>0.95 driver life >25000 Hours, operating range 140v to 280 V includingall accessaries all as specified and directed.
