tender for Green Gym at META Hostel B 17 and 18,MERI,Nashik.-Excavation for foundation in earth,soil of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary backfilling, ramming, watering including shoring and strutting etc. complete. (Lift upto 0.00 to 1.50 m.) By Manual Means providing and laying cement concrete pipe of IS 458:2003 NP-2 class of 450mm diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc. complete Providing soling using 80 mm size trap metal in 15 cm. layer including filling voids with sand / grit, ramming, watering complete. Providing and laying Cast in situ/Ready Mix cement concrete in M-15 of trap/granite/quartzite/gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is Providing and erecting chain link fencing 1.6M. height with G.I. chainlink of size 50 x 50 mm, 8 gauge thick and fixed 75 mm above ground level on vertical M.S.Angles of 40x40x6 mm size, includingh excavating pits for foundation and embedded in C.C. block of 1:4:8 mix of size 450x450x670 mm. at 1.75 M .c/c with iron bar 16 mm dia as holdfast including welding link with angle frame at 30 cm c/c with nuts and bolts and horizontal M.S. Angles at top and bottom of 25x25x5 mm size and vertical M.S.flat 35x5mm and 25x5 mm horizontal including cross support of 40x40x6 mm angles both side at every corner or bend embedded in concrete blocks of 1:4:8 of size 450x450x 670 mm including 3 coats of oil painting etc. complete. Providing fly ash brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete Providing rough cast cement plaster externally in two coats to concrete, brick or stone masonry surfaces in all positions with base coat of 12 to 15 mm thick in C.M. 1:4 and rough cast treatment 12mm thick in proportion 1:1 1/2:3 including scaffolding and fourteen days curing complete. Providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding I.S. of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface, applying primer coat scaffolding if necessary , and watering the surface for two days etc complete. :-Providing and fixing mild steel grill gate with angle iron frame 65mm x 65mm x 10mmwith iron bars at 150mm C/C and diagonal flats as per the detailed drawing includinghinges, pivot block locking arrangement, welding riveting and oil painting of three coats ofapproved shade Weight of gate 35 Kilogram/Smt. Testing of materials Royalty charges for materials to be used for the work. sand rubble Providing and fixing ‘Sky Walker’ manufactured by combination of mild steel and allseason artificial wood to seek eco-friendly greenery effect. Dimensions: (L X W X H) = 1780X630X1700mm. Main Frame Cover - Completely covered top to bottom with all-season artificial wood, outer size 120X120mm, 93X93mm inner area to accommodate square tube shape which is completely molded in one single piece. Artificial Wood 100% water resistance and duly certified by CII for green products. Artificial wood should consist Wood Powder more than 50%. U.V. Resistance as per IS 14887–2000. round pipes should be of “heavy grade as per IS 1239 (Highest thickness as per 1239) Main Frame - Consist – 90X90x3mm Thickness Square Tube get maximum internal strength to structure. Paddle vertical support – 25 NB Heavy grade GI pipe. Handle – 25 NB Heavy grade GI pipe dually bending design. Leg movement frame – 50mmX50mmX3mm thick square pipe. Providing and fixing ‘Chest Press Double’ manufactured by combination of mild steel and all-season artificial wood to seek eco friendly greenery effect. Dimensions: (L X W X H) = 1800X650X2150mm. 1) Main Frame Cover - Completely covered top to bottom with all-season artificial wood, outer size 120X120mm, 93X93mm inner area to accommodate square tube shape which is completely molded in one single piece. 2) Artificial Wood 100% water resistance and duly certified by CII for green products. Artificial wood should consist Wood Powder more than 50%. U.V. Resistance as per IS 14887 – 2000 Main center pipe- - 90X90x3mm Thickness Square Tube get maximum internal strength to structure. All round pipes should be of “heavy grade as per IS 1239 (Highest thickness as per IS 1239) 3) Remaining frame- made up of 40NB & 50NB Heavy grade G.I. pipe. 4) Handle - Made up of 40NB Heavy grade G.I. pipe. 5) Connecting Link - made up of 25NB Heavy grade G.I. pipe. 6) Seats & Back-rests are of 300x320mm GI antirust material of minimum 2.0 mm thick duly deep drawn in tool & dies with uniform radius of 20mm. Welded permanently with the equipment to avoid future theft, vandalism or damages may occur due to bad handling or misuse. 7) Handle is connected with frame by 8mm laser cutting MS profile 8) Main Pipe Top Closing cap’s- Decent Design Size 120X120 Providing and fixing ‘ROWER’ manufactured by combination of mild steel and allseason artificial wood to seek eco-friendly greenery effect.Dimensions: (L X W X H) = 1670X1010X1140mm.1. Main Frame Cover - Completely covered top to bottom with all-season artificial wood, outer size 120X120mm, 93X93mm inner area to accommodate square tube shape which is completely molded in one single piece. Artificial Wood 100% water resistance and duly certified by CII for green products. Artificial wood should consist Wood Powder more than 50%. U.V. Resistance as per IS 14887 – 2000. All round pipes should be of “heavy grade as per IS 1239 (Highest thickness as per IS 1239)2. Main Frame - Consist – 90X90x3mm Thickness Square Tube get maximum internal strength to structure.3. Base Frame- made by 80 NB Heavy grade GI pipe.4. Connecting link made up of 25 NB & 32 NB Heavy grade GI pipe.5. Seat support pipe & Leg rest pipe made up of 50 NB Heavy grade GI pipe.6. Handle frame made from 25 NB Heavy grade GI pipe.7. Main Pipe Top Closing caps- Decent Design Size 120X120 SS304 Material.8. Seat 320X300mm of GI antirust material of minimum 2.0 mm thick duly deep drawn tool & dies with uniform radius of 20mm. Welded permanently with the equipment to avoid future theft, vandalism or damages may occur due to bad handling or misuse.9. Nut & Bolts Closing Caps- All Nut & Bolt closing caps made from SS of 0.7 mm thick duly pressed in dies and tools. Providing and fixing ‘Sit Up Board double’ manufactured by combination of mild steel and all-season artificial wood to seek eco-friendly greenery effect. Dimensions: (L X W X H) = 1700X1200X600mm. 1) Main Frame Cover - Completely covered top to bottom with all-season artificial wood, outer size 120X120mm, 93X93mm inner area to accommodate square tube shape which is completely molded in one single piece. 2) Artificial Wood 100% water resistance and duly certified by CII for green products. Artificial wood should consist Wood Powder more than 50%. U.V. Resistance as per IS 14887 – 2000. Main center pipe- - 90X90x3mm Thickness Square Tube get maximum internal strength to structure. All round pipes should be of “heavy grade as per IS 1239 (Highest thickness as per IS 1239) 4) Top and Bottom Leg Support- 50NB Heavy Grade G.I Pipe. 5) Main Frame Bottom Support- 80x40mm rectangular Pipe MS material. 6) Remaining Frame 50NB Heavy Grade G.I Pipe. 7) Backrest Seat should have wooden finish aesthetic look. 8)Foundation stool: Made from main pipe 90x90x3mm pipe and top support of M.S. plate of 250X250mm Square 10mm thickness is welded top. 40X8mm MS flat with 20x40mm M.S. pipe. Height of stool is 500mm. 11) Foundation plate –M.S. 250X250mm Square With 10mm thick. 12) Main Pipe Top Closing cap’s- Decent Design Size 120X120 SS304 Material 13) Hardware Nut & Bolts- Stainless Steel SS Material Providing and fixing ‘Leg Press Double’ manufactured by combination of mild steel and all-season artificial wood to seek eco-friendly greenery effect. Dimensions: (L X W X H) = 1810X370X1500mm.1) Main Frame Cover - Completely covered top to bottom with all-season artificial wood, outer size 120X120mm, 93X93mm inner area to accommodate square tube shape which is completely molded in one single piece.Artificial Wood 100% water resistance and duly certified by CII for green products. Artificial wood should consist Wood Powder more than 50%. U.V. Resistance as per IS 14887 – 2000. All round pipes should be of “heavy grade as per IS 1239 (Highest thickness as per IS 1239)2) Main Frame - Consist – 90X90x3mm Thickness Square Tube get maximum internal strength to structure3) Seat Frame Top support- Made by 32 NB Heavy grade GI pipe. Attached 5 mm thick MS4) 5.00 mm Plate for Demountable system.5) Foot rest support pipe-Made by 25 NB Heavy grade GI pipe. Attached 5mm thick MS Plate for Demountable system6) Seat Frame Main Pipe – Made by 32 NB Heavy grade GI pipe. Attached 10mm thick MS laser Profile Plate for Demountable system7) Seat frame - Ø 32 NB Heavy grade GI pipe. Duly Bend8) Leg Press back rest should be angled in 100-120 degree. Providing and fixing ‘Shoulder Builder Double’ manufactured by combination of mild steel and all- season artificial wood to seek eco- friendly greenery effect. Dimensions: (L X W X H) 900X680X1850mm. 1) Main Frame Cover - Completely covered top to bottom with all-season artificial wood, outer size 120X120mm, 93X93mm inner area to accommodate square tube shape which is completely molded in one single piece. 2) Artificial Wood 100% water resistance and duly certified by CII for green products. Artificial wood should consist Wood Powder more than 50%. U.V. Resistance as per IS 14887 – 2000. Main center pipe- - 90X90x3mm Thickness Square Tube get maximum internal strength to structure. All round pipes should be of “heavy grade as per IS 1239 (Highest thickness as per IS 1239) 3) Ring Fitting Top support- Made by 50NB Heavy Grade GI pipe. Attached 8 mm thick MS plate 4) Shoulder Builder ring – 25NB Heavy Grade G.I Pipe. 5) Shoulder ring And Bearing Bush support Pipe– 20NB Heavy Grade G.I Pipe. 6) Nylon knob with Bearing – Is fixed on shoulder ring pipe for rotating purpose, 2 set to be fixed in a position for kids and adults. 7) Main Pipe Top Closing cap’s- Decent Design Size 120X120 SS304 Material 8) Hardware Nut & Bolts- Stainless Steel SS Material 9) Nut & Bolts Closing Caps- All Nut & Bolt Closing caps made from SS304 of 0.7mm thick duly pressed in dies and tools. 10) Foundation stool: Made from main pipe 91x91x2mm pipe and top support of M.S. plate of 250X250mm Square 8mm thickness is welded top. Torque steel is used to support center pipe. Height of stool is 3ft. 11) Foundation plate –M.S. 250X250mm Square With 10mm thick. 12) Foundation stool: Made from main pipe 90x90x3mm pipe and top support of M.S. plate of 250X250mm Square 10mm thickness is welded top. 40X8mm MS flat with 20x40mm M.S. pipe. Height of stool is 500mm. Providing and fixing ‘Standing-Seating Twister’ manufactured by combination of mild steel and all- season artificial wood to seek eco-friendly greenery effect. Dimensions: (L X W X H) = 1850X520X1500mm.1) Main Frame Cover - Completely covered top to bottom with all-season artificial wood, outer size 120X120mm, 93X93mm innerarea to accommodate square tube shape which is completely molded in one single piece.Artificial Wood 100% water resistance and duly certified by CII for green products. Artificial wood should consist Wood Powder morethan 50%. U.V. Resistance as per IS 14887 – 2000.All round pipes should be of “heavy grade as per IS 1239 (Highest thickness as per IS 1239)2) Main Frame - Consist – 90X90x3mm Thickness Square Tube get maximum internal strength to structure.3) Seat plate support – 50NB Heavy grade G.I Pipe.4) Seating Footrest ring - 25NB Heavy grade G.I Pipe made by rolling.5) Seating ring support – 20NB Heavy grade G.I Pipe.6) Bottom Seat and Standing Support – Made From 100X50X2.5mm Pipe Attached 8 mm thick MS Plate for Demountable system.7) Standing plate - Ø300mm OD X 10mm thick M.S. plate.8) Seating plate - Ø300mm OD X 10mm thick M.S. plate.9) Handle – 25NB Heavy grade G.I. Pipe made by rolling10) Main Pipe Top Closing caps- Decent Design Size 120X120mm SS304 Material.11) Nut & Bolts Closing Caps- All Nut & Bolt closing caps made from SS304.12) Hardware Nut & Bolts - Stainless Steel13) Foundation stool: Made from main pipe 91x91x3mm pipe and top support of M.S. plate of 250X250mm Square 10mmthickness is welded top. 40X8mm MS flat with 20x40mm M.S. pipe. Height of stool is 500mm.
