Tender For Special Repair To Bldg No P-8 At Jakli Under Ge 970 Ews; 1 Demolition of brick work built in cement mortar complete all as specified and directed. 2 M&L Labour for brick work with sub class `B’ bricks, straight on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed. 3 M&L for brick work with sub class `B’ bricks, straight on plan to any radius in half brick thick walls, built in CM 1:4 complete all as specified and as directed 4 Demolition of cement concrete in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and as directed. 5 Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and as directed 6 Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping) complete all as specified and as directed 7 M&L for RCC Type B1 1:2:4 (using 20mm aggregate) for slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like complete all as specified and as directed 8 M&L precast reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cover slabs (for manholes etc), shelves and similar articles with plain faces including necessary moulds and setting in cement mortar 1:6 including necessary form work complete all as specified and directed. (reinforcement to be measured separately) 9 M &L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia or securing with clips complete all as specified and directed. 10 M&L 100 mm thick PCC (1:4:8 ) type D-2 as in sub base finished even and roughcomplete all as specified and as directed. 11 M&L for 25mm thick PCC 1:2:4 type B-0 (12.5mm graded stone aggregate) as in level course with finshining in cement concrete surface even and rough to receive screed bed complete all as specified and directed. 12 Dismantling floor, hearth, wall tiling including taking down plastering in cement mortor removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. 13 Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc. complete all as specified and as directed. 14 M&L for 16-18mm thick Granite (of any type)work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over screed bed of 15 mm thick 1:6complete all as specified and directed. 15 M&L for Mirror polished Kota Stone slab flooring 20-25 mm thick over cement screed bed 20 mm thick 1:3, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. 16 M&L for mirror polished Kota Stone slab 20-25 mm thick in riser of steps, skirting, dado and, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with backcoat of screed bed or bedding layer 10mm thick 1:3 and pointed in white or coloured cement to match complete all as specified. 17 M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed. 18 M&L Joint free Non - skid coloured ceramic tiles 7 to 10 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry over screed bed of 15 mm thick 1:6 and pointed in white or coloured cement to match complete all as specified and as directed 19 M&L Joint free Non - skid coloured ceramic tiles 7 to 10 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm in skirting/dado or verticle surfaces with back coat of screed bed or bedding layer of 10 mm thick 1:4 and pointed in white or coloured cement to match complete all as specified. 20 M&L Joint free Non - skid coloured ceramic tiles 7 to 10 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry over screed bed of 15 mm thick 1:6 and pointed in white or coloured cement to match complete all as specified and as directed 21 M&L Glazed coloured ceramic tiles in verticle surfaces 450 x 300 x 7mm thickset and jointed in neat cement slurry and pointed in coloured cement to match with backcoat of screed bed or bedding layer 10mm thick 1:4 and pointed in white or coloured cement to match complete all as specified. 22 S&F selected quality looking mirror bevelled edge 5.5mm thick selected quality glass, mounted on 6mm thick commercial plywood, including moulding of all round edges of looking mirror and fixed to wooden plug with appropriate nos CP brass screwed cup washers complete all as specified and directed. 23 M&L 75 mm thick PCC (1:4:8 ) type D-2 as in sub base finished even and roughcomplete all as specified and as directed. 24 M&L Johnson Endura premium paving tiles of techno commercial or equivalent of size 40cm x 40cm x 10 mm thick, set, jointed and pointed in neat cement slurry in floors, laid over 15 mm thick bedding layer in Cement Mortar 1:6 complete all as specified and as directed. 25 M&L for cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades shelves, lintels etc, and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10cm girth all as specified and as directed 26 Taking up or down GI Water Tubing 15mm dia (bore) including Connections and Fittings, segregating serviceable Pipes & Fittings and Stacking properly at Site(s) for re-use, complete all as specified and as directed. 27 Description all as per ser item No 26 above, but for 20mm dia (Bore). 28 M&L for 16 mm dia 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified. 29 Description all as per ser item No 28 above, but for 20mm dia (Bore). 30 Description all as per ser item No 28 above, but for 32mm dia (Bore). 31 Taking up or down and refixing old PP-R pipe20mm ida and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and as directed 32 M&L Lagging to pipes used in internal water supply (internal dia of pipe 20mm) or plumbing all round with,25min thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144 Kg/cum conforming to IS 9842 Description all as per ser item No 26 above 33 Dismantling water tanks of capacity exc 500 but not exc 1000 ltr capacity complete. 34 S&Frotational moulded polythene water storage tanks tripple layer(cylindrical vertical with closed top) hoisted and fixed in postion 1000 ltrs capacity with and including 25mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe minimum weight 210 gramcomplete all as specified and directed. 35 S&F 25mm dia PP-R Gate valves (brass insert) as per requirement of the site complete all as specified and as directed 36 S&F in repair vitreous China squatting pan, Orissa pattern incl PVC trap, size 580 x 440 mm white, with integral foot rests squat pattern closet also includes setting the trap and pan in cement concrete (1 cement, 2 sand or surkhi and 5 aggretate), min. 150mm thick all round and finished just below level of rim of pan to receive the floor finishing (thickness as indicated) and making good floor complete all as specified incl cutting to the flush pipe and necessary repair to the floor complete all as specified and directed. 37 S&F in repair PVC Flushing Cistern 10 litre capacity, Low Level Valve Less, Symphonic Action type, White, with Inlet, Ball Valve, Float and Handle including 32mm dia PVC Flush Pipe, a Pair of MS Brackets,CP flush bend including Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 including taking down unserviceable Flushing Cistern and connected Items of any description, complete all as specified and as directed. 38 S&F vitreous china wash basin with pedestal, white, flat back, size 550mm x 400mm, including brackets,PVC waste pipe 32mm dia,wastecoupling brass, chromium plated and including cutting for and pinning in ends of brackets or erecting stand, fixed in repairs complete all as specified and directed. 39 S&F brass Chromium plated Basin Mixer valve hot and cold screwed down for iron pipe complete all as specified and directed. 40 S&F Brass CP Wall mixer for mixing hot & cold water (3 in 1)screwed down for iron pipe and fixed bore of pipe 15mmcomplete all as specified 41 S&F in repair 15mm dia bib taps fancy type CP Brass with Capstanhead, screweddown, screwed for iron pipe of bore 15mm complete all as specified and directed. 42 S&F in repair Angle Cock,15mm fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. 43 S&F PVC Connections 15mm size with PTMT Nuts of length 600mm and fixed, complete all as specified and as directed. 44 S&F Brass CP Sink Mixer with regular spout for mixing hot & cold water screwed down for iron pipe and fixed bore of pipe 15mm complete all as specified and directed. 45 S&F Brass chromium platedshower rose 125mm size with 225 mm Flange, swivel joints, including fixing to steel pipe or unioncomplete all as specified and directed. 46 S&F Tubular towel Rail CP Brass, chromium plated D type with CP Brackets, 600 mm long between flanges complete all as specified and directed. 47 S&F Glass shelf 450 x 125 x 6MM (with ABS Bracket chromium platedbracket guard and SS railing complete all as specified and as directed 48 S&F Soap Dish Stainless Steel complete all as specified & directed. 49 S&F Peg Set of 6 Stainless Steel complete all as specified and directed. 50 S&F Corner Glass Shelf 300mm (with ABS Brackets) 300 x 300mmcomplete all as specified and directed. 51 S&F Towel Ring including necessary stain less steel screws, rawl plugs and washers complete all as specified and directed. 52 S&F stainless steel plate rack of stain less steel 1.00 mm thick of size size 24 x 30 x 10 inch of best quality including necessary stain less steel screws, rawl plugs and washerscomplete all as specified and directed. 53 S&F sinks without drain board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. 54 Demolition and taking out cement mortar or lime concrete, brick bats from sunken floor portion complete all as specified and as directed. 55 M&L for preparing surface of sunken slab and applying 15mm thick cement plaster 1:3 cement sand mortar with integral water proofing compound both on floor & wall.The surface shall then be cured and allowed to dry then applying Epoxy Resin coating Polymer modified cementation coating like brush bond of Fosroc, Pidilite and Bostic as per manufacturers instructions both on floor as well as on wall and sunken floor shall be filled with graded cinder concrete upto top level to receive top flooring, incl providing 25mm dia GI spout pipe projecting 0.25mtr beyond the external face of wall complete all as specified and directed. 56 M&L for 40mm thick PCC 1:2:4 type B-0 as in Sunken Portion of WC/Bath room (using 12.5mm graded stone aggregate) complete all as specifed and directed. 57 M&L for lime conrete with lime mortar 1:5:10 mix using 40mm graded brick coarse aggregate in sunken Portion of WC/bath room complete all as specified and as directed. 58 Dismantling of PVC / CI pipe 100mm dia jointed in cement mortar and taking out of trench if required complete all as specified. 59 Dismantling of PVC / CI pipe 75mm dia or less jointed in cement mortar and taking out of trench if required complete all as specified. 60 S&F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls and making good with cement mortor 1:3 complete all as directed. 61 S&F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in trenches or in floorsand making good with cement mortor 1:3 or with PCC 1:2:4 complete all as directed. 62 S&F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls and making good with cement mortor 1:3 or with PCC 1:2:4 complete all as directed. 63 S&F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in trenches or in floors and making good with cement mortor 1:3 or with PCC 1:2:4 complete all as directed. 64 S&F in repair PVC 110 mm bore Bendcomplete all as specified and as directed. 65 S&F in repair PVC (SWR) junction single, (Single T) equal or unequal with access door in110 mm bore. 66 S&F in repair PVC 75 mm bore Bend complete all as specified and as directed. 67 S&F in repair PVC 75 mm bore Bend with access door complete all as specified and as directed. 68 S&F in repair PVC (SWR) junction single, (Single T) equal or unequal with access door in75 mm bore complete all as specified and directed. 69 S&F in repair PVC (SWR) vent cowl 110 mm bore complete all as specified and as directed. 70 S & F in repairs for PVC (SWR) floor/Nahani trap 75 mm dia outlet, plain with grating including jointing with solvent cement to waste pipe, fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed. 71 Taking down chowkats or frames n.exc 1.50 sqm each with shutters (without taking off shutters from the frames) complete. 72 Taking down chowkats or frames exc 1.50 sqm but n.exc 4.00sqm each with shutters (without taking off shutters from the frames) complete. 73 S&F solid PVC door frame of size 50x47mm made of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed. 74 S&F Factory Made Solid PVC Moulded Door Shutter With Particle Board Core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed. 75 S&F Box type steel window (Fatory made) outer frame made out ERW tube P section 65mm x 45mm x 25mm and shutter with glazed openable shutter of ERW tube P section 50 mm x 35mm x 20 mm openable (double) shutter with glazed openable shutter on (external side) and wire gauzed openable shutter on (Internal side) with steel pintal hinges, steel handle 100 mm long, mild steel tower bolt 02 nos on each shutter, stopper of Z section and its locking arrangement at mild steel hook and eye including 0.36mm dia nominal dia of stainless steel wire cloth avg width of aperture 1.40mm dia, 4 mm thick sheet glass window & 4mm figured glass for ventilators and guard bars (MS square bar 10mm dia), all as specified and as directedby Engr-in-Charge.Note. The quoted rate against the above item shall also include(i)For provn of one shop coat of zinc chromate primer on all exposed steel surfacces and one oat tar on the ends of steel frame in contact with bricks/concrete surface.(ii)04 Nos MS Steel Lugs of 20 x 5mm, MS flat 20 cm long over all welded to frames. (iii) PCC block for embedding lugs.(iv) 0.36 mm dia SS wire mesh.(v) 4mm thick sheet glass for window.(vi) Guard bars. 76 M&L Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165complete all as specified and directed. 77 M&L for PCC 1:3:6 type C-1(using 20mm graded stone agg) for bed block for fixing hold fast complete all as specified. 78 M&L for providing PCC 1:2:4 type B-0 as in roof kerbs or mud stops rouded or chamfered on edges (using 12.5mm graded stone aggregate) complete all as specifed and directed. 79 M&L Pressed steel frames (Factory made) made out of 1.25 mm thick black MS sheet for doors, with one or more rebates including necessary s&f lugs, Butthinges, lock strike plate, etc complete, size of frame 125x60mm incl bottom of each chowkat to be welded with 2 nos 25x25x3mm thick flat iron projecting 10 cm on either sidecomplete all as specified and directed. 80 M&L Pressed steel frames (Factory made) made out of 1.25 mm thick black MS sheet for doors, with one or more rebates including necessary s&f lugs, Butthinges, lock strike plate, etc complete, size of frame 105 x 60mm incl bottom of each chowkat to be welded with 2 nos 25x25x3mm thick flat iron projecting 10 cm on either sidecomplete all as specified and directed. 81 S&F 35 mm thick, factory made 2nd class hardwood glazed and skeleton shutters, open rebated and prepare to receive gauge etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for secruing glass/gauge etc size of member of shutter as specified in SSR Part-I Section 8 Clause 8.20(a), fitted to chowkats complete all as directed. 82 S&F35mm thick flush shutters, solid core construction, with block board core and plywood face panesls, commercial type on bothe sides complete all as specified and as directed. 83 S&F 18mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work complete all as specified and as directed 84 M&L for 0.9mm thick decorative laminate type 1 of surface finish, colour and patters as approved, fixed with approved adhesive as per manufacturers insturctions, complete all as specified. 85 S&F Push to open Magnetic Catches for kitchen cabinet doors complete all as specified and directed. 86 S&F Contnuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps (when open) 30mm complete all as specified and directed. 87 S&F Stainless Steel Decorative Cabinet Handle 100 mmcomplete all as specified and directed 88 S & F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed. 89 S&F Floor door stopper of aluminum alloy body and tongue anodized with hard drawn steel spring fixed in floor of length 150mm complete all as specified and directed. 90 S&F Stainless Steel butt hinges medium weight of size 100 mm fixed with stainless screws complete all as specified and directed. 91 S&F Extruded aluminium alloy handles 150 mm long fabricated type anodised complete all as specified and directed . 92 S&F 200mm size aluminium anodised, barrel tower bolt of extruded section complete all as specified and directed. 93 S & F 150 mm long aluminium anodized barrel tower bolts of extruded section lcomplete all as specified and as directed. 94 S&F 250 mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixingclips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified directed. 95 S&F Decorative Stainless steeltubular curtain rail of 25mm dia incl six nos curtain ring per running mtr and one number of brackets on each end and one no of globe on each end of the rod per opening of door / window (make and materail approved by Engineer-in-charge) complete all as specified and directed. 96 S&F 2nd class hardwood small fittings such as brackets of any type, latch and hinge blocks, shaped door and widnow stops and the like, including all necessary labour; articles no exc 200 cu. cm each complete all as specified and as directed 97 Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) any thickness, including cover fillets but without frame work. 98 S&F Powder coated galvanised iron frame work for seamless ceiling size 600mm x 600mm with main runner 38 x 24 x 0.90mm thick, cross tee 29 x 24 x 0.90mm thick and wall angle 24 x 24 x 0.90mm thick duly suspended with 6mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip complete all as specified and as directed. 99 S&F 6mm thick Non Asbestos fibre cement building boards/Pre Laminated self embossed texture designer E-Board classic(Size 0.60M x 0.60M), HPSC (High pressure steam cured) to be fixed or laid/inserted to existing/new timber/GI/Aluminium/MS framework with screws as in ceiling complete all as specified and directed. 100 Dismantling of Plain or corrugated steel sheeting, any gauge, thickness complete all as specified. 101 S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, height upto & inl triple sotrey bldg as specifiedare to be fixed using torque adjustable electronic gun screws drills of suitable capacity complete all as specified. 102 Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick as in ridges, eves board of any colour having tensile strength of 550 Mpa as inroof covering/cladding to wall, fixed with self tapping screws in any heightcomplete all as specified and directed. 103 Dismantling boarding, any description, fixed in any position with nails complete all as specified. 104 S&F rolled mild steel sections channel angle Tee section and in tubular sectionas in main and cross beams, hip and jack rafters; purlins,post where connected to common rafters and running rails fixed with angle cleat or other connecting plates conforming to Fe 410-W Gde-E-250, quality A complete all as specified and directed. 105 S&F framed work such as grills,gratings, etc with ends of bars shouldered and / or riveted or forged into spikes; framed guard ; barred iron doors; ladders ; framed balusters; walk ways; railing and simillar work Con-forming to Fe 290 Gde E-165 complete all as specified and directed. 106 Taking down cement plaster on brick or stone walls etc raking out joints hacking for key scrabbing down water etc complete. 107 M&L for 15mm thick cement plaster in CM (1:4) on fair faces of brick or concrete surfaces using WPC where ever requiredas per manufacturerers instructions and finishing the surface even and smooth (without using extra cement) etc. incl finishing even and faircomplete all as specified NOTE -WPC shall be measured and paid separetely. 108 M&L for rendering 15mm thick on fair faces of brick work in CM 1:6 finished even and fair without using extra cement complete. 109 M&L for rendering 10mm thick in CM (1:3) on fair facesor concrete ceiling surfaces finished even and fair without using extra cement complete. 110 Supply only WPC complete all as specified and directed. 111 M&L for applying two coats of synthetic eneamel painting over a coat of pink primer on new wooden surfaces exc 10 cm width or girth including preparation of surfaces complete. 112 M&L for one coat of synthetic enamel paint to old decorated steel surfaces of girth exc 10cm including preparation of surfaces complete 113 M&L for two coats of synthetic enamel painting over a coat of red oxide zinc chrome primer on new steel surfaces over 10cm width or girth including preparation of surface complete. 114 Preparing new plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion, white or tinted over & including a coat of primer complete. 115 M&L for complete removal of existing surface and applying two coats of oil bound distemper over a coat of primer white or tinted on old decorated/undecorated surfaces of wall complete all as specified and directed. 116 M&L for 2mm thick wallcare putty on wall complete all as specified and as directed 117 M&L preparing new plastered or unplastered surfaces of Ceiling and applying two coats of distemper oil emulsion paint complete all as specified and as directed 118 M&L for complete removal of existing surface and applying two coat of Oil Bound Distemper over a coat of primer on old decorated/undecorated surfaces of Ceiling complete all as specified and as directed. 119 M&L for 2mm thick wallcare putty on ceiling complete all as specified and as directed 120 M&L for preparation of newly plastered surfaces of wall applying a layer of wall care putty 2mm thick (averaging) , Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed 121 M&L for complete removal of existing treatmentby srapping down of old surface of wall applying a layer of wall care putty 2mm thick (averaging) , Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed 122 M&L 75mm thick PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate as in plinth protection incl finishing even and smooth w/o using extra cement complete all as specified and directed. 123 M&L for cement concrete 1:2:4 type B-1 using (20 mm graded stone aggregates) as surface channels and drains complete all as specified and directed. 124 M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed. 125 Taking down unserviceable any type of Main Switch, DBs including MCBs incl wooden/GI/MS sheet board etc and removing from site and making good the disturbed surface of wall etc all as specified and as directed by Engr-in-Charge. 126 Taking down and M & L for concealed point wiring with FRLS-H, PVC insulated, unsheathed multistranded copper conductor cables 1100 Volts grade of 1.5 sqmm size (Phase and Neutral) alongwith one earth continuity conductor with FRLSH PVC insulated unsheathed multistranded copper conductor cable 1100 Volts grade of 1.5 sqmm size through and including 20 mm dia (medium grade) rigid non metallic PVC concealed conduit terminated and suitable for modular metal flush box as per site requirement for fixing of switches, sockets, fan regulators etc including testing on completion complete including cutting chases for concealed conduit piping in making good to facing and pointing in using cement mortar 1:3 and making good to disturbed surface for the following. complete all as specified and directed. 127 Description all as per item No 126above but for one 3 pin socket outlet, 5 Amp on same modular board with other switches, with cable 1.5 Sq mm size. 128 Description all as per item No 126above but for one 3 pin socket outlet 5 amps on the Indepdent modular board with other switches, with cable 1.5 Sq mm size. 129 Supply and fixing of Socket,6A - 3 pin combined 2 module, fabio series 6 Amps 3 pinunversal socket with child safety shutter, Shrouded terminals compatible with all standard mobile chargers, ISI marked for the same board complete all as specified and directed. 130 Supply and fixing of Modular switch socket outlet multipurpose 3/5 pin 5 amp flush type, ISI marked complete all as specified and directed.Make: 131 Taking down and M & L for one point wiring with PVC insulated un-sheathed cable with stranded copper conductor FR-LSH conforming to IS : 694 of size 2.5 Sq mm single core, including one No. 2.5 Sq mm single core PVC insulated un-sheathed copper cable FR-LS as continuous earth wiredrawn in and including PVC conduit with all accessories of same grade,concealed on wall/ceiling including terminatedin to Modular switch board / Cast iron/pressed steel terminal box 60mm deep of required sizemade out of 2mm thick MS sheet duly painted both sides with 3 mm thick plasticlaminated sheet top cover fixed with brass screw & cup washers for mounting switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type / modular type on the independent board complete all as specified and as directed. 132 Supply and fixing of modular Switch and Socket outlet 16A - 5 pin combined 3 module,(Fabio classic white) shuttered socket (heavy duty) 3 pinunversal socket with child safety shutter, Shrouded terminals compatible 2 ton AC and 3.5KW geyser, ISI marked for the same board complete all as specified and directed. 133 Description all as per item No 132above but one light point controlled by two 2 - w a y s w i t c h e s with cables1.5 sq. mm size complete all as specified and directed. 134 Supply and fixing modular switch 2 way 6A,1 module complete all as specified and directed. 135 Supply and fixing in repairCeiling rose, 3 phase/PVC/polycarbonate, isolated body type complete all as specified and directed. 136 S & Fof tube light fitting, with LED batten with polycarbonate housing and integrated electronic drive 1x 22 watts 4 feet twin light mode rechargeble fitting with white acrylic cover along with LED lamp white colour complete including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed. 137 S & F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fitting of LED lamp 9 watt complete all as specified and directed. 138 S & F LED lamp 9 watt complete all as specified and directed 139 Hanging only ceiling fan and connecting up including provision of cable fromceiling rose to fan complete all as specified and directed. 140 Fixing only exhaust fan and connecting up including provision of cable from ceiling rose/connector to fan. 141 Fixing only Electric Water Heater and connecting up including provision of cable from Geyser Point complete all as specified and directed. 142 Supply and fixing modular fan regulator, 120 /100 W- 2 module regulator electronic step type 230 Volts single phase all as specified and directed. 143 Supply and fixing of Modular switch 1 way 6A, 1 module modular Switch fabio classic white series/Switch fabio classic white with indicator, ISI marked switch complete all as specified and directed. 144 Disconnecting electric supply from electric meter and dismantling MS electric meter box of any size including electric meters, switch gear, MCCB/MCBs etc complete and supply fabricate testing and commissioning of MS sheet electric meter box 2 mm thick double door with locking arrangement of size/dimension not less than 130x75x30 cm with suitable thickness of ylem sheet for fixing existing electric meter -06 Nos including provision of new MCCB 160 A -01 No,MCB SPN 63 A-06 Nos with suitable size of aluminium bus bar for phaseneutral and see through glass connecting internally prewired copper conductor with electric meter connecting of required size applied with power coated synthetic enameled paint and making good to the distrubed wall surface complete all as specified and directed. 145 S & F DB with sheet metal enclosure 240 volts, 8 way with 200 Amp rated bus bar single pole & neutral double door type for MCBs including mounting work as required in position .complete all as specified and as directed 146 Supply and fixing of amp rating 240V, 10KA curve miniature circuit breaker (MCB) SPN and current carrying capacity 40 Amps in the MCB DB complete with connection testing and commissioningcomplete all as specified and directed. 147 Supply and fixing of amp rating 240V, 10KAcurve miniature circuit breaker (MCB) SP and current carrying capacity 5-32 Amps in the MCB DB complete with connection testing and commissioning complete all as specified and directed. 148 Taking down and M&L for Sub Main wiring using FRLS Insulated unsheathed, multistrand copper conductor FRLS PVC cable 2 runs of size 2.5 sqmm for phase and neutral and 2.5 Sq mm for earthing. drawn through rigid PVC conduitof suitable sizefixed on wall/ground/Ceiling etc., complete all as specified and directed. Two runs of cable for phase / neutral and one run of cable for earth incl conduit will be measured and paid as one unit length. 149 Taking down M&L for Sub Main wiring using FRLS Insulated unsheathed, multistrand copper conductor FRLS PVC cable 2 runs of size 4 sqmm for phase and neutral and 4 Sq mm for earthing. drawn through rigid PVC conduitof suitable sizefixed on wall/ground/Ceiling etc., andcomplete all as specified and directed. Two runs of cable for phase / neutral and one run of cable for earth incl conduit will be measured and paid as one unit length. 150 Taking down M&L for Sub Main wiring using FRLS Insulated unsheathed, multistrand copper conductor FRLS PVC cable 2 runs of size 6 sqmm for phase and neutral and 6 Sq mm for earthing. drawn through rigid PVC conduitof suitable sizefixed on wall/ground/Ceiling etc., and complete all as specified and directed. Two runs of cable for phase / neutral and one run of cable for earth incl conduit will be measured and paid as one unit length. 151 Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impactand corrosion resistant including thermal management in multiple optics complete withIP 65/66 protection complete. including connections with 2 run of 2.5 Sq mm aluminium unsheathed wire multistranded from LT over head line / junction box to the connector of fitting, complete all as specified. 152 S & F street light bracket made out of GI tubing 32 / 40 mm dia, light grade of approx length 1.2 mtr long bend to shape suitable for security light fittings with necessary MS clamps - 02 Nos with one coat of anti corrosive primer and two coats of aluminium paint including nut, bolt, washers etc all as specified. 153 M & L for Earthing complete with galvanised steel earth plate, electrode, 600x600x6.0 mm thick burried directly in ground (earth pit not less than 2.25m deep below normal ground level) connected to galvanised earth lead wire 4.0 mm dia by mens of nuts, bolts, & washers of GI as shown in electrical plate No. 5 of SSR Part-I Connected to earthing ten point all as specified and including necessary earth pit PCC 1:3:6 chanber be 50mm thick PCC 1:2:4 chamber cover with 6mm dia mild steel reinforcement of 10 cm c/c spacing both ways in lieu of CI cover , watering arrangement shall be made with GI pipe medium grade of 20mm dia including funnel and protection to earth lead shall be provided with GI pipe light grade 15mm dia upto 7.5 from the earth plate electrode & refilling of soil etc including necessary excavation & earth work in any strata and PCC chamber complete all as specified and directed including demolish existing earth pit taking out old materials. 154 S & F modular white cover plate with frame 3 module complete all as specified and directed. 155 S & F modular white cover plate with frame 6 module complete all as specified and directed. Make-Anchor Roma/Crabtee/Schneider. 156 S & F modular white cover plate with frame 8 module complete all as specified and directed. 157 Supply and laying in repairof XLPE insulated,sheathed,armoured,heavy duty LT 1100 volts grade cable 25 Sqmm3.5 core with aluminium conductor laid in trenches/pipes, fixed topoles/walls with suitable saddle complete all as directed. 158 Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 M in depth and getting out in hard /dense soil for taking up or laying of cable all as specified and directed. 159 Returning,filling in including spreading, levelling, watering and well ramming in layers not exceding Cum 25cm complete al as specified and directed. 160 Removal of surplus soil not exceed to a distance of 50M where directed at a level not exc 1.5M above the starting point. 161 Supply and laying dry river sand laid in trenches as cable cushioning and covering complete all as secified and directed. Note : Punned thickness only measured and paid. 162 M&LforGalvanised steel tube, light grade withallfittingsfor cable protectionfixed with polesof50mmbore includingcomplete allasspecifiedanddirected. 163 M & L for brick well brunt locally available sub classA laid over sand cushioning to cable in trenches keping width of brick parallel to the length of cable complete all as specified and directed. 164 Taking out/taking down old unserviceable damaged GI/PPR pipe of following sizes from excavated trenches including removing of fittings all as directed for necessary replacement /relaying serviceable GI pipe complete all as specified and directed. 165 (a)32/40 mm dia 166 (b)25 mm dia 167 Supply and Laying of PPR pipes 3- layer SDR 7.4 of outer diameter of pipes as following UV stabilized and antimicrobial fusion welded having thermal stability for hot and cold water supply all PPR plain& brass threaded polypropylene random fittings laid in trenches including fittings and testingcomplete all as specified and directed. 168 (c) 32 mm dia. 169 (d) 50 mm dia. 170 M&L for construction of Brick Masonry valve chamber of size 600x600x600mm (Internal dimensions) with PCC 1:4:8 foundation 150mm thick, brick work built in CM 1:6, PCC 1:3:6 coping 50mm thick, plastering 15mm thick in CM 1:6 to all internal and exposed surfaces including excavation earthwork in hard/dense soil, MS sheet cover 6mm thick and MS equal angle iron 50mmx50mmx6mm frame as per existing sizewith locking arrangement embedded in PCC suitable for 25/40/50mm gate valve and painting to MS cover with two coats of synthetic enamel paint over one coat of red oxide primer etc complete including dismantling old/damaged valve pits. 171 Making connection of PPR distribution branch with PPR main ofsizes 50 mm to 75 mm by providing and fixing tee including cutting and making fusion joint etc complete all as specified and directed. 172 Taking out unserviceable Gate valves from water pipe line for necessary replacement all as directed for valve size 15mm to 32mm complete all as specified and directed. 173 Taking out unserviceable Gate valves from water pipe line for necessary replacement all as directed for valve size 40mm to 80mm complete all as specified and directed. 174 Supply and fixing PPR gate valve (brass insert) of size 25 mm dia including connection and testing complete all as directed. 175 Supply and fixing PPR gate valve (brass insert) of size 50 mm dia including connection and testing complete all as directed. 176 S&F GI Flat strip clamps of size 25mm x 3mm duly bended as per the size of GI tubing and site condition,drilled complete all as specified and directed. 177 Supply and fixing of heavy rust proof passivated bolts made of steel of size 8 mm dia 75mm long including necessary drilling on wall for fixing of steel frame complete all as specified and directed. 178 M&L Lagging on pipes of internal dia 15 mm, used in external water supply or plumbing all round with, 40mm thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144 Kg/cum conforming to IS 9842, provided with chicken mesh wire netting 25 gauze 20mm mesh and finally covering with plaster of pairs including taking down old, complete, all as specified and directed for the size of 25 mm bore tubing. 179 Description all as per item No. 178 above but 32 mm bore tubing complete all as specified and directed. 180 Description all as per item No. 178 abovebut 50 mm bore tubing complete all as specified and directed. 181 Notes :- Amount of Credit Schedule for Schedule A Part-ll shall be deducted from total quoted amount of BOQ to arrive at the contract sum
