Tender For Up Gradation Of Various Smqs (Phase-Ii) At Af Stn Barrackpore.; 1 Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided including removing of rubish from site complete all as specified and directed. 2 Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided including reinforcement cut as required to facilitate demolition and removing debries from site of work completeall as specified and directed. 3 Dismantling of timber scantling 40 Sqcm and over in section, in any position in framed work and removing materials from site of work complete all as specified and directed. 4 Dismantling of wrought iron or mild steel work of any description not otherwise provided for and removing materials from site of work complete all as specified and directed. 5 Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc including brushing neat cement slurry with 3.00 kg of cement per sqm completeall as specified and directed. 6 Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises completeall as specified and directed. 7 Taking down chowkats or frames with shutters n.exc. 1.50 Sqm each (without taking off shutters from the frames) complete all as specified and directed. 8 Taking down chowkats or frames with shutters exc. 1.50 sqm but n.exc 4.00 sqm each (without taking off shutters from the frames) complete all as specified and directed. 9 Taking down shutters of any description exc. 1.00 Sqm but n.exc. 2.00 Sqm each complete all as specified and directed. 10 Taking down cement plaster of any description built in cement mortar on brick or stone walls etc including racking out joints, hacking for key, scrubbingdown with water etc. and removing debrish from site complete all as specified and directed. 11 Demolition of brick work or stone boulder masonry, built in cement mortar including all quoins, arches, pillars etc.including removing of unserviciable material from site complete all as specified and directed. 12 Taking down wooden door/window of area n.exc 4.00 sqm each carefully and refixing in the same opening after necessary repair such as stay handle etc and making good to existing surface with cement mortar (1:3) complete all as specified and directed.Note:- Concrete required for fixing hold fast shall be included in quoted rate. 13 Taking down chowkats or frames with shutters exc. 1.50 sqm but n.exc 4.00 sqm each (without taking off shutters from the frames) and refixing in same opening with using hold fast, minor cement concrete work and making good complete all as specified and directed. 14 Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed. 15 Taking up or down 20 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed. 16 Supply and fix 15 mm bore steel tubesmedium grade, galvanised, with all fitting and fixed to walls, ceilings, roofs or laid in floorscomplete all as specified and directed. 17 Supply and fix 20 mm bore steel tubesmedium grade, galvanised, with all fitting and fixed to walls, ceilings, roofs or laid in floors complete all as specified and directed. 18 Laying / fixing only 15 mm bore steel water tubing with and including all fittings and fixed to walls and ceilings or laid under floorscomplete all as specified and directed.Note;- Serviciable GI pipe shall be refixed under this item obtained from item No 14.00 after taking up/ down. 19 Laying / fixing only 20 mm bore steel water tubing with and including all fittings and fixed to walls and ceilings or laid under floorscomplete all as specified and directed.Note;- Serviciable GI pipe shall be refixed under this item obtained from item No 15.00 after taking up/ down. 20 Material and labour for 15mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar (1:4) andfinish the surfaceseven and smooth without using extra cement as in wall complete all as specified and directed. 21 Material and labour for 10mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar (1:6) andfinish the surfacesfair and even on wall complete all as specified and directed. 22 Material and labour for 5mm thick rendering onconcrete surfaces in cement mortar (1:3) andfinish the surfaceseven and smooth without using extra cementin ceiling complete all as specified anddirected. 23 Material and labour for preparation of new plastered surfaces of walls and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqmcomplete all as specified and directed. 24 Material and labour for preparation of new plastered surfaces of walls and applying two coats of acrylic washable distemper over a coat of alkali resistance primer including applying 1mm thick wall care putty complete all as specified and directed. 25 Material and labour for preparation of new plastered surfaces of ceiling and applying three coat of white wash completeall as specified and directed. 26 Materials and labour for complete removal of existing treatment of old decorated surfaces of walls and applying two coats of acrylic washable distemper over a coat of alkali resistance primer including applying1mm thick wall care putty including preperation of surface complete all as specified and directed. 27 Material and labour for preparation of new wooden surfaces of any description exc 10 cm width or girthand applying two coats ofsynthetic enamel paint over a coat of pink primer complete all as specified and directed. 28 Material and labour for preparation of new steel surfaces of any description over 10 cm width or girthand applying two coats ofsynthetic enamel paint over a coat of red oxide zinch chrome primer complete all as specified and directed. 29 Material and labour for preparation of old painted wooden surfaces of any description over 10 cm width or girthand applying one coat ofsynthetic enamel paint complete all as specified and directed. 30 Material and labour for preparation of old painted steel surfaces of any description over 10 cm width or girthand applying one coat ofsynthetic enamel paint complete all as specified and directed. 31 Material and labour for preparation of old decoratedsurfaces of wall and applying one coat of white wash complete all as specified and directed. 32 Material and labour for preparation of old decorated surfaces of ceiling and applying one coat of white wash complete all as specified and directed. 33 Material and labour for preparation of old decorated surfaces of walls and applying one coat of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 0.715 litre/ 10 sqm complete all as specified anddirected. 34 Material and labour for machine cut cudappah stoneslab 20-25mm thick as in shelf including rubbing and polishing complete including taking down existing shelf complete all as specified and directed. 35 Material and labour for PCC (1:2:4), type B1, (using 20mm graded stone aggregate), as in coping, bed plate, kerbs, water troughs and like including weathering, slightly rounded or chamfered angles and throating, including necessaryformwork complete all as specified and as directed 36 Material and labour for brick work with sub class `B` bricks, old size,straight or curved on plan exc 6m mean radius built in cement mortar (1:6)complete all as specified and directed. 37 Materials and labour for half brick thick brick work with sub class `B` bricks, old size, straight or curved on plan to any radius built in cement mortar(1:4) complete all as specified and directed. 38 Material and labour for well-seasoned 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed. 39 Material and labour for well-seasoned 2nd class hard wood plain fillets, square, rectangular or triangular insection, wrought, secured with nails or brads, sectional area exc. 13 sqcm but not exc. 25 sqcm including taking down existing fillets complete all as specified and directed. 40 Supply and fix factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45x85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 41 Supply and fix factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65X150 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 42 Supply and fix factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws complete all as specified and directed. 43 Supply and fix factory made PVC wire gauzed door shutters 30mmm thick (style) consisting of frame made of MS tube for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC `C channel having a PVC sheet strip of 20 mm width Stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail.Panelling of wire gauzed shutter, the wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly and jointed together with solvent cement as per specification and drawing given on MES schedule Part – II (2020) complete all as specified and directed. 44 Supply and fix 35mm thick 2nd class hard woodGlazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars) edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass,etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) and fitted to chowkats complete all asspecified and directed. 45 Supply and fix 30mm thick second class hardwood plain framed panelled shutters (any numbers of panels) with panels of timber flat both sides (feather edged) or of veneered particle board medium density, wood particle with commercial face veneers including framing is moulded on solid (for each side) and fitted to chowkats complete all as specified and directed. 46 Supply and fix 30mm thick flush shutters, solid core construction, with block board core and plywoodpanels, commercial type, both face complete all as specified and directed. 47 Supply and fix powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws complete all as specified and directed. 48 Supply and fix powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws complete all as specified and directed. 49 Supply and fix anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening complete all as specified and directed. 50 Supply and fix mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders, framed balusters, walk ways; railings, framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. 51 Material and labour for second class hard woodsmall fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labours; articles n. exc 200 cu. cm each complete all as specified and directed. 52 Suplly and fix 100mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed. 53 Suplly and fix 150 mm long aluminum anodised barrel tower bolts cast type complete all as specified and directed. 54 Supply and fix 100mm long aluminium handles, cast type, anodized complete all as specified and directed. 55 Suplly and fix 300 mm long aluminium alloy, anodised,sliding door bolt with hasp, staple (bolt type) and fixingclips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast- aluminium alloy complete all as specified and directed. 56 Supply and fix in repair mild steel 300mm long ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed. 57 Supply and fix in repair 18/19mm thick pre-laminated particle board, exterior grade, pre-laminated both side with decorative choice lamination including 2nd class hard wood leaping fixed to frame work complete all as specified and directed. 58 Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed. 59 Supply and fix 4 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 Sqm in each pane complete all as specified and directed. 60 Supply and fix 4 mm thick sheet glass ordinary quality and glazing with oil putty in square exc 0.5 Sqm in each pane complete all as specified and directed. 61 Supply and fix 5 mm thick figured glass pin head type and glazing with oil putty in square n. exc 0.5 Sqm in each pane complete all as specified and directed. 62 Supply and fix stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. 63 Supply and fix in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. 64 Material and labour for RCC (1:2:4) type B-1 (using 20mmgraded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. 65 Material and labour for mild steel TMT bars 10mm dia and over, cut to length bent to shape required, including cranking bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and directed. 66 Material and labour for form work to sides and soffits of floor or roof beams, beam haunchings, girders, bres-summers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. with rough finished flat surfaces of concrete complete all as specified and directed. 67 Supply and fix in repair kitchen stainless steel sink of steel grade-304, 1.00 mm thickwith plug, washers and wastes including bedding in cement mortar to dwarf wall or including cantilever cast iron brackets, connecting union etc., overall size 495 mm x 420 mm with bowl size 410mm x 330mm x 160mm including 32 mm bore waste coupling PTMT (minimum weight 45gms)and 32 mm dia PVC corrugated flexible waste pipe of 800 mm longcomplete all as specified and directed. 68 Material and labour for ceramic coloured tiles (premium quality) 7 to 8mmthick (square/rectangular) area of each tile exceeding 0.18sqm but not exc. 0.38sqmas in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bed in cement mortar (1:6)complete all as specified and directed. 69 All as per item No 68.00 above but in skirting and dado laid over and including 10mm thick rendering in cement mortar (1:4) and -ditto-. 70 Material and labour for ceramic, non skid coloured tiles (premium quality) 7 to 8mmthick (square/rectangular) area of each tile exceeding 0.11sqm but not exc. 0.18sqmas in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bed in cement mortar (1:6)complete all as specified and directed. 71 Material and labour for glazed ceramic tiles of size 300x450x7-8 mm (premium quality) coloured in vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10mm thick cement plaster in cement mortar (1:4) completeall as specified and directed. 72 Material and labour for 20mm thick black marble (Jade black ) tiles machine cut in cooking plateform and jointed with grey cement slurry including cutting and polishing of type laid over and including 20mm thick screed bed in cement mortar (1:6)complete all as specified and directed. 73 Material and labour for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations completeall as specified and directed. 74 Material and labour for cutting chases, pinning in brick wall making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing and making good, cutting not exc 10 cm girth complete all as specified and directed. 75 Supply and fix in repair 15mm bore stop valves, castcopper alloy, fancy type, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed bothends for iron pipe or for unions complete all as specified and directed. 76 Fixing only in repair 15mm bore fancy type, chromium plated, bib tap, cast copper alloy with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as specified and directed. 77 Supply and fix in repair 15mm bore fancy type sink tap chromium plated brass, round headed single liver with quarter turn option with areator, swan neck type wall mounted with extruded brass made spindle and housing with wall flange, screwed down high pressure with long screwed shanks, screwed for iron pipe complete all as specified and directed. 78 Supply and fix in repair 15mm bore brass angle cock fancy type, chromium plated foriron pipe complete all as specified and directed. 79 Supply and fix in repairPVC connection pipe 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed. 80 Supply and fix in repair brass chromium plated shower rose 125mm size with or without swivel joint complete all as specified and directed. 81 Fixing only in repair 15mm bore fancy type pillar tap cast copper alloy with capstan heads, chromium plated, screwed down, high pressure with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and directed. 82 Supply and fix in repair 125mm PTMT grating doom(minimum weight 40gms) complete all as specified and directed. 83 Supply and fix in repair vitreous china wash down water closet pan (pedestal Pattern) white (excluding fixing bolts flusing cistern and flush pipe) including connection to drain (or out going pipe) and to flush pipe anti syphonage pipe including cast iron P or S trap fixed on floorcomplete all as specified and directed. 84 Supply and fix in repair plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed. 85 Supply and fix in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed. 86 Supply and fix in repair 10 litre capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and flush pipe complete all as specified and directed. 87 Supply and fix in repair vitreous china wash hand basin, white, flat back, size 550x400mm excluding taps, waste pipe, chain & plug and porcelain stopper but with brackets and 32 mm bore brass waste fittings chromium plated including cutting for and pinning in ends of brackets complete all as specified and directed. 88 Supply, hoist and fix 500 litre capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling of old unseviciable existing tank and removing from site complete all as specified and directed. 89 Supply and fix in repair 20mm dia ball valvehigh pressure high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gm) complete all as specified and directed. 90 Supply and fix in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. 91 Supply and fix in repair 40mm bore high density polyethylene pipes (HDPE) with all fittings of pressure rating 6 kgf/sqcm fixed to walls, ceilings or in floors etc. complete all as specified and directed. 92 Supply and fix in repair 25 mm dia aluminium anodised decorative/fancy type drapery rodwith bracket complete all as specified and directed. 93 Supply and fix in repair looking mirror ofsize 600mm x 450mm x 5mm thick bevelled edge of selected quality glass, decorative type mounted on 6mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers completeall as specified and directed. 94 Dismantling of 110/100/75mm dia PVC/ cast iron or reinforced concrete drain pipes with all fittings, jointed in cement mortar and taking out of trenches/ from wall, if required complete all as specified and directed. 95 Supply and fix solid PVC door frame of size 50x47 mm made out of 5mm PVC sheet plain colour reinforced with MS square tube as per specification and drawinggiven in SSR Part-II 2020 complete all as specified and directed. 96 Supply and fix factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement as per specification and drawinggiven in SSR Part-II 2020 complete all as specified and directed. 97 Material and labour for welding in repairs n. exc 2.5cm in length, thickness of metal to be welded exc 6mm but n. exc 9mm complete all as specified and directed. 98 Supply and fix 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls including stack clamp of suitable size complete all as specified and directed. 99 Supply and fix 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed. 100 Supply and fix 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls including stack clamp of suitable size complete all as specified and directed. 101 Supply and fix 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed. 102 Supply and fix 110mm bore PVC (SWR) juction single (singleT) equal or unequal with access door complete all as speified and directed 103 Supply and fix 110 mm bore PVC (SWR) bends with access door any radius complete all as speified and directed. 104 Supply and fix 75mm bore PVC (SWR) bends any radius complete all as specified and directed. 105 Supply and fix 75mm bore PVC (SWR) juction single (singleT) equal or unequal complete all as speified and directed 106 Supply and fix in repair 75 mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed. 107 Supply and fix in repair 32mm bore PVC corrugated waste pipe 800mm long complete all as specified and directed. 108 Supply and fix in repair brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed. 109 Supply and fix in repair towel ring of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 90gms) complete all as specified and directed. 110 Supply and fix in repair door stopper 150mm long cover plate, aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed to shutter complete all as specified and directed. 111 Supply and fix in repair 5mm thick glass corner shelf of size 300 x 300mm with stainless steel railing fixed with chromium plated screws complete all as specified and directed. 112 Supply and fix in repair stainless steel plate rack 0.85 mm thick of size 786x914x254mm of steel grade-204 complete all as specified and directed. 113 Supply and fix solid PVC wall lining consisting of 5 mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC/Aluminium frame complete all as specified and directed. 114 Supply and fix in repair soap dish, brass, chromium plated complete all as specified and directed. 115 Material and labour for 75mm thick PCC (1:3:6) type C-1 (using 20mm graded stone aggregate) as in plinth protection, laid in panels including finishing the concrete surface even and smooth without using extra cement complete all as specified and directed. 116 Material and labour for forming 12 mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘B’,thickness of concrete slab in 75mm complete all as specified and directed. 117 Supply and fix in repair gun-metal globe or gate valves 20 mm dia with iron wheel head screwed both ends for iron pipe complete all as specified and directed. 118 Material and labour 75mm thick PCC (1:3:6), type C-2 (using 40 mm graded stone aggregate) as in sub-basecomplete all as specified and directed. 119 Material and labour forjoint free anti skid outdoor pavement coloured tiles (good grip series) of size 300 x 300 x 10mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including 20mm thick screed bed in cement mortar (1:6) complete all as specified and directed. 120 Material and labour for cutting holes into or through brick wall built in cementmortar of superficial area not exc 150 sqcm and making good in CM (1:3) or cement concrete (1:2:4) type B-1 as required complete all as specified and directed. 121 Material and labour for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm including cleaning surfaces complete all as specified and directed. 122 Material and labour for preparation of newly bitumen surfaces and applying two coats of bituminous aluminium paint @ 0.10 ltrs per sqm per coat complete all as specified and directed. 123 Complete removal of existing roof treatment in any layers and disposal of debris from site complete all as specified and directed.Notes: - (a) The rates are inclusive of removal for any type of old water proofing treatement over main RCC slab.(b) Bidders are advised to visit the site and esure about site condition before quoting their rates.(c) Demolition of PCC/ taking down plaster if any shall be measured and paid saparately under respective items. 124 Material and labourfor 15mm thick rendering in cement mortar (1:4) with using water proofing coumpound (WPC) @ 200 ml per bag of cement or as per manufacturers instruction on roof top and finish the surfaceseven and smooth without using extra cement including taking down existing cement plaster and disposal of debris from site complete all as specified and directed.Note : WPC will be measured and paid separately under respective item. 125 Supply only liquid water proofing compound (WPC) completeall as specified and directed. 126 Material and labour for 25mm thick PCC (1:2:4) type B-0 (using 12.50mmgraded stone aggregate) as in any position complete all as specified and directed. 127 Material and labour for water proofing treatment to RCC roof surface comprising with the following course of treatment/specifications from bottom to top :- (a) Applying cold bituminous primer @ 0.30 liters per sqm confirming to IS 3384 over plastered surfaces of roof.(b) One layer of APP based polymeric membrane3mm thick, weight not less than 3.50 kgs per sqm, reinforced with non woven polyester matt central core fabric (weight not less than 160 GSM) and coated on both side with and including layer of APP modified bitumen and finished with and including micro-prefabricated heat fusible polythene film on both surfaces. (c) Finally applying two coats of bituminous aluminum paint @ 0.10 ltrs per sqm per coat on top surface.Note:-(i) Laying of APP based polymeric membrane shall be done by torch on method or as per manufacturers instructions. (ii) A minimum overlap of 150mm and 100mm should be made in the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as per manufacturers instructions.(iii) The work shall be executed only through authorised applicator of manufacturer as approved by GE. Make of APP membrane:- Super Thermolay of M/s STP Ltd, Hyperplas of M/s IWL India Ltd, Hydrostop of M/s Tiki Tar Danosa (India) pvt ltd, , M/s FOSROC Chemicals, Smartcare APP membranes of M/s Asian Paints Ltd. 128 Material and labour for mild steel round bars 10 mm dia and over cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips conforming to Fe-410-W (Gde-E quality-A) or Fe-290 (Gde-E 165) complete all as specified and directed. 129 Supply and fix rolled mild steel in joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) of Fe 410 -W (Gde-E- 250) quality-A including one shop coat of red oxide zinc chrome primer complete all as specified and directed. 130 Supply and fix 0.50mm thick pre-painted galvalume aluminium Zinc coating GI based corrugated / semi corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturer instruction complete all as specified and directed. 131 Material and labour for 40mm thick PCC (1:2:4), type B-1, (using 20mm graded stone aggregate) as in sub base or base of floor complete all as specified and directed. 132 Material and labour for anti-termite treatement for treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall including making good disturbed surfaces complete all as specified and directed.Note :The work shall be executed only through authorised applicator as approved by GE. 133 Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. .complete all as specified and directed. 134 Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store for keeping in safe custody for reuse complete all as specified and directed. 135 Material and labour for light/fan point wiring (concealed type) with single core PVCinsulated unsheathedmultistranded FRLSH copper conductor cable of 1100 volts grade size 1.5 sqmm (nominal area) in and including 20mm dia heavy duty rigid non metalic PVC conduit with accessories including modular flush metal boxeswith inner and outer modular cover plates for housingswitches, sockets and regulatorswith all fittings and fixing materials with one single core PVC insulated unsheathed 1.5 sqmm (nominal area) multistranded FRLSH copper conductor as earth continuity wire and connected to earth dolly complete all as specified and directed.Note: (a) Red coloured cable shall be used for live connection,black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for Each individual circuit from the distribution board.(b) Quoted rate shall be included for cuttings /chasing the wall and making good disturbed surfaces to fix PVC conduit and flush metal box.(c) Inner and outer modular cover plate shall be measured and paid seperately under respective items. 136 All as per item No. 135.00 here-in-before but for bell/buzzer point controlled by one push button on independent board and -ditto-. 137 All as per item No. 135.00 here-in-before but for one five pins 5 Amps switch socket outlet point on independent board and -ditto-. 138 All as per item No. 135.00 here-in-before but for one five pins 5 Ampssocket outlet point on same board and -ditto-. 139 All as per item No. 135.00 here-in-before but for 15 amps socket outlet on independent board with 2.5 sqmm PVC insulated (FR-LSH) unsheathed copper cable multistranded conductor 1100 volts grade including 2.5 sqmm PVC insulated (FR-LSH) unsheathed copper cable multistranded conductor 1100 volts grade as earth continuity conductor and connecting to common earth dollyand -ditto-. 140 Supply and fix modular switch 1 way 6 amps, 1 module complete all as specified and directed 141 Supply and fix modular switch 1 way 16 amps, 1 module complete all as specified and directed. 142 Supply and fix modular bell push 6 amps, 1 module complete all as specified and directed. 143 Supply and fix modular shuttered sockets 6 amps, 3/5 pin combined two module complete all as specified and directed. 144 Supply and fix modular shuttered sockets 6/16 amps, 3/5 pin combined two module complete all as specified and directed. 145 Supply and fix modular fan regulator step type 120W, 2 module complete all as specified and directed. 146 Supply and fix modular white cover plate with frame of 1/2 module complete all as specified and directed. 147 Supply and fix modular white cover plate with frame of 3 module complete all as specified and directed. 148 Supply and fix modular white cover plate with frame of 8 module complete all as specified and directed. 149 Supply and fix modular white cover plate with frame of 6 module complete all as specified and directed. 150 Supply and fix in repair LED tube light fitting 1 x 20W (+/- 5%), 220V, AC with extruded strip in thermally conductive material & extruded housing in optically efficient material milky white with system lumen efficacy > 120 lumen per watt minimum system 2300 - 2400 and chip, Integrated electronic driver, SMD based LED constant current supply with double sided connection to avoid short circuit and surge protection greater than 2.5 KV, IP 20 protection and CRI>80, Power factor > 0.95, THD less than 15%, correlated Colour temperature (CCT) of 6500K, Operating Voltage of 140 V to 270 V, frequency of 50Hz burning hours 50000 hours with comprises of CRCA pre coated metal housing complete all as specified and directed. 151 Supply and fix in repair LED lights fittings with extruded aluminium housing, high quality PC diffuser, efficacy- 100lm/W, 10 watt, 220V, AC, 6500K, CRI ≥80, 2 feet long, integrated design including connecting up withflexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. 152 Supply and fix in repair LED street light fitting 35 Watt, 230 volts made with pressure die cast housing with toughened glass with high powered LED, IP-66 protection high power LED with secondary lenses and system efficiency should be minimum 110 lumen per watt. Driver should be BIS approved silicon filled potted driver with inbuilt 4KV surge protection device, THD shall be <10%, power factor >.95, CCT 5700K and brand name should embossed/engraved on the LED fitting for traceability till life complete all as specified and directed. 153 Supply and fix wall mounted fan, metal body AC single phase. 230V of size 450 mm sweep, with, blades, and frames complete all as specified and directed. 154 Supply and fix 300mm sweep steel body exhaust fan AC single phase 230/240 volt. 1400 RPM, heavy duty, ISI marked, along with metal blade powder coated metalic finish with GI sheet louvers, low noise including necessary electric connection with and including cutting/making opening having dia of the hole for 300mm sweep exhaust fan inany type of walls of any description with nut, bolt, washer and making good distrubed surfaces complete all as specified and directed. 155 Supply and fix in repair sheet metal enclosureSPN DB 8 waysdouble door having facility to fix MCB in incomer and MCBs in outgoing,metal door IP-43type complete fitted with bus bars, neutral links, blanking plates complete all as specified and directed. 156 Supply and fix in repair MCB SPN, 240 Volts, 40amps, C series, breaking capacity 10 KA complete all as specified and directed. 157 Supply and fix in repair MCB SP, 240 Volts, of 6 to 32 amps current rating, 10 KA breaking capacity C series complete all as specified and directed. 158 Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fancomplete all as specified and directed.Note:- Item obtained from item No 134.00 shall be reused under this items. 159 Fixing only LED tube light fitting of any watt with bracket with necessary electrical connection 1.5 sqmm 2 core copper condutor wire complete all as specified and directedNote:- Item obtained from item No 133.00 shall be reused under this items. 160 Taking down electric meter from inside room and refixing the meter with necessary electrical connection near main DB under stair case in proper mannar including Supply and fix PVC enclosure box made out of thermoplastic sheet having IP-66 protection of size 400mm x 300mm x 190mm in front openable type with fixing nut & bolt clamps including writing of Qtr Number on meter Box by paintcomplete all as spcified and directed. 161 Taking down electric water heater from bathroom room and refixing the same after finishing of bathroom with fixing nut & bolt if required complete all as spcified anddirected.Note - Contractor kept the water heater in safe custody for reuse and if any damaged found contractorreplaced with new one without any extra cost. 162 Material and labour forconcealed submain wiring comprising single core , 2 run of 4 sqmm nominal cross sectional area, FR-LSHmultistrandedcopper conductor cable, PVC insulated unsheathed 1100 Volts gradedrawing in and including appropriate dia. in PVC conduit and its fittings complete including provision of 1run of 4 sqmm nominal cross sectional area, FR-LSH multistranded copper conductor cable, PVC insulated unsheathed 1100 Volts grade as earthwirecomplete including taking down old unserviciable sub main wiring complete allas specified anddirected.Note :-(a) Cost for extra length of cables / wire required for connection to MCBs/DBs shall be included in quoted rates.(b). Cost for cuttings /chasing of wall etc and making good the disturbed surface shall be included in quoted rates. 163 Material and labour for earthing complete with GI earth plate electrode of size 600x600x6 mm thick buried directly in ground with earth pit not less than 2.25 meter deep below ground level with top edge of plate not less than 1.5 meter below normal ground level connected to GI wire 4 mm dia earth lead by means of nuts, bolts, check nuts, washers of galvanized iron as steel,protected by 15mm dia GI pipe (medium grade) including cement concrete (1:3:6) type C-1 earth pit with precast RCC (1:1.5:3) type A-1 cover slab of size 42 x 42 x 6 cm thick reinforced with 8mm dia TMT bars @ 15 cm c/c both ways with 10mm dia mild steel round bar of 30 cm long, bent to shape as lifting handle, funnel,wire mesh, 20 mm bore galvanized iron pipe (medium grade) for watering, earth testing point, charcoal or coke and salt in alternate layers with necessary earth work in soft/loose soil complete all as shown in electrical plate No 3 of SSR Part I including testing on completion complete as specified and directed.Note:- GI wire upto 7.5m including testing shall be included in qouted rates. 164 Material and labour for earth continuity conductor or main earthing lead with4mm dia GI wire, fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or DBs / Indoor type LT PBs orany other indicated situation for loop earthing etc complete all as specified and directed 165 Supply, laying, connecting and testing XLPE insulated, PVC sheathed, armoured LT electric power UG cable (heavy duty with stranded aluminum conductor)of size 16 Sqmm, 2 core, 1100 Volts grade, confirming to IS-7098 (Part-I) laid through duct/ pipe / in trench etc. with cable glands & suitable size of aluminium lugscomplete all as specified and directed.Note : Earth work, brick protection and sand cushioning and GI Pipe Shall be measured and paid separately under respective item. 166 Excavation in trenches n. exc 1.5 m wide and n. exc 1.5 m in depth for foundation etc or for shafts, wells, cess pits man holes, pier holes etc n.exc 10 sqm on plan and n.exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed. 167 Returning filling in including spreading levelling watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and directed. 168 Removing excavatedmaterial (soil) notexc 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed. 169 Material and labour for sand cushioning with clean and dry river sand for protection of XLPE UG cable with approved sand of uniform thickness. laid dry, filling in trenches and punning down in proper required layers complete all as specified anddirected. Note:- Punned down thickness shall be measured for payment. 170 Material and labour for brick protection cover to underground cables with sub class ‘B’ of size 23 X 11.5 X 7.5 cm, (locally available best quality), laid dry and flat abutting each other with gaps not exceeding 10mm complete all as specified anddirected. 171 Supply and fix 40 mm dia HDPE pipe of pressure rating 10 kgf/cm2for passing of cable through PCC foundation from trench to cable junction box with necessary clamp nuts and bolts complete all as specified and directed. 172 Materials and labour for boring for passing GI/HDPE protection pipe up to 50 mm bore (dia) under road / footpath without disturbing the top surface complete all as specified and directed Note-Necessary infrastructure required for boring shall by arranged by the contractor and cost of the same included in quoted rates. 173 Material and labour for cutting existing CI/GI/DI water supply line with the help of electric cutting tools or manually, reducing to required length before laying and blockage removal, cleaning of particular joint etc and making good after repairing ofsize upto 100mm dia including leakage testing complete all as specified and directed. 174 Materials and labour for cutting existing 100 mm dia CI/GI/DI water supply line with the help of electric cutting tools or manually for insertion of new tee of size 100x100x25mm, branches, etc. complete all as specified and directed. 175 Supply and fix 25 mm bore steel tubesmedium grade, galvanised, with all fitting and fixed to walls, ceilings, roofs or laid in floorscomplete all as specified and directed. 176 Supply and fix 25 mm bore steel tubesmedium grade, galvanised, with all fitting and laid in trenchescomplete all as specified and directed. 177 Supply and fix 20 mm bore steel tubesmedium grade, galvanised, with all fitting and laid in trenchescomplete all as specified and directed. 178 Supply and fix gun-metal globe or gate valves 25 mm dia with iron wheel head screwed both ends for iron pipe complete all as specified and directed. 179 Supply and fix gun-metal globe or gate valves 20 mm dia with iron wheel head screwed both ends for iron pipe complete all as specified and directed.
