Tender For Purchase Of Opem Gym Equipments In Ward 38 Chest Press Cum Shoulder Press : Providing And Fixing Chest Press Cum Shoulder Press Fnf 016 (Make Fun Play ) Using, Minimum 100 Nb Gi C-Class Pipe For Center Frame , Minimum 40 Nb & 32 Nb Gi B-Class , Ernakulam-Kerala

Tender For Purchase Of Opem Gym Equipments In Ward 38 CHEST PRESS CUM SHOULDER PRESS : Providing and fixing Chest press cum shoulder press FNF 016 (Make FUN PLAY ) using, minimum 100 NB GI C-class Pipe for CENTER FRAME , Minimum 40 NB & 32 NB GI B-class Pipe for MAIN FRAME , Minimum 32 NB & 25 NB GI B -CLASS Pipe for HANDLE FRAME , Minimum 32 NB &25NB &40NB GI B CLASS Pipe for CONNECTING PIPE , LLDP Rotomoulded seat with inbuilt bolts 3/8 x 1.5 for SEAT & BACK REST , Nylon 66 injection moulded BEARING CAP & PIPE CAP , fully Done by first coat of primer -jotun Brad 40-50 Micron thickness and Top coat of pure polvester powder with 70-80 micron thikness POWDER COAT including cost of concrete foundation , all materials, labour, etc all complete asper the instruction of Engineer in charge CYCLE : Providing and fixing Cycle - FPSPCL208 (Make FUN PLAY ) using , 25NB & 40NB GI B-Class Pipe for MAIN FRAME , 32 NB GI B-CLASS pipe for SEAT FRAME , 25NB GI B-CLASS Pipe for HANDLE FRAME , Nylon 66 injection moulded BEARING CAP & PIPE CAP , fully Done by first coat of primer - jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70-80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour, etc all complete asper the instruction of Engineer in charge Leg Press (Double) -Supply and Installation of Double Leg Press having the following specifications: Dimensions: (L X W X H) = 1676 x 400 x1500 mm. Main frame - Ø 114 mm OD “B” class GI pipe. Foundation plate – M.S. round plate of Ø 250 mm & 8 mm thick. Foundations cover cap - dome shape of PP/NYLON/HDPE material. Link - is Ø 60 mm OD “B” Class GI pipe. Seat frame - Ø 42 mm OD “B” Class GI pipe. Leg Press back rest should be angled in 120-130 degree. Foot rest-cast iron 124 x 296 x 5 mm thick and M.S plate of 2 mm thick use to support it. Seat & back rest – 380 x 275 x 60 mm thick high-density polyethylene (HDPE) blow molded with M10 in-sert wall thickness 3 to 4 mm. Link connected with frame by 8 mm thick laser cutting MS profile. Top Closing cap – dome shape made by PP/ NYLON/HDPE material. Closing cap’s- PP/ NYLON/HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded at top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Bearing- use is 6005 permanent lubricated reputed brand. Pin– Ø 25 mm M.S. bright bar pin. Bearing bushes - Ø 60 mm OD seamless pipe. Circlip– A 24 circlips are used for assembly. Coating - best quality of powder coating 80-120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be welded as per IS standards and zinc primer paint should be applied at all the welding points prior to finishing.<br> SIT UP BOARD made from C Class GI pipe to be use by two persons at one time. Closing Caps are made up of Low Linear Density Poly-Ethylene (LLDPE) Material with Injection Moulding. The powder coat should be Poly urethane & Epoxy powder with 60 to 70micron thickness. Dimensions: 2000mm (Length) x 1100mm (Width) x 650mm (Height).

INR 665 /-

INR 3 Lakhs /-