|
| 1 | Dismantling roofingincludingridges, hips, valleys andgutters etc.,andstacking the material within 50 metres lead of: Asbestos cement sheet. |
| 2 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 3 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %)total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7\ microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm) |
| 4 | Repairing of wooden false ceiling by providing plywood/ wooden sheet in any level & fixed it to main ceiling with connecting clipss, screws, wooden bidding, etc. including all necessary fittings, etc complete as per direction of Engineer-In-Charge. |
| 5 | Providing and fixing Air turbulent ventilator 24\" fan each S.S. & Aluminium ERP Dome sheet length 1800mm, width 1 meter, dome height 500mm, Dome bottom 670mm x 1050mm & thickness 1.5mm etc. including cutting of GI profile sheet. Jointing, welding, bolting, etc as required & complete in all respect as per direction of Engineer-In-Charge. |
| 6 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area2.5 sq.meters and under, including cutting the patch in proper shape,raking out joints and preparing and plastering the surface of the wallscomplete, including disposal of rubbish to the dumping ground, allcomplete as per direction of Engineer-in-Charge.With cement mortar 1:4 (1 cement : 4 fine sand) |
| 7 | Providing and applying white cement based putty of average thickness1 mm, of approved brand and manufacturer, over the plastered wallsurface to prepare the surface even and smooth complete. |
| 8 | Distempering with 1st quality acrylic distemper, having VOC (VolatileOrganic Compound ) content less than 50 grams/ litre, of approvedbrand and manufacture, including applying additional coats whereverrequired, to achieve even shade and colour. Two coats |
| 9 | Providing and fixing UPVC pipe 15mm nominal bore as per direction of Engineer-In-Charge. |
| 10 | Providing and fixing PTMT bib cock of approved quality and colour.15mm nominal bore, 86 mm long, weighing not less than88 gms. |
| 11 | Providing an d fixingwhite vitreous china pedestal type watercloset (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever),conformingto IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid |
| 12 | Providing and fixing uplasticised PVC connection pipe with brass unions. 30 cm length.15 mm nominal bore |
| 13 | Providing andfixing PTMT angle stop cock 15 mm nominal bore, weighing not less than 85 gms |
| 14 | Providing and fixing wash basin with C.I. brackets,15 mm C.P. Brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps. |
| 15 | Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms |
| 16 | Half brick masonry with common burnt clay F.P.S. (non modular) bricksof class designation 7.5 in superstructure above plinth level up to floorV level. Cement mortar 1:4 (1 cement :4 coarse sand) |
| 17 | 15 mm cement plaster on the rough side of single or half brick wall ofmix :1:4 (1 cement: 4 fine sand) |
| 18 | Providing and fixing black kadappa stone as shelves 25mm. thick machinepolished, extending the polish upto 20 cm width on lower side, rounding corners,laying in position jointing with bedding cement mortar1:4 proportion curing etc etc. Complete |
| 19 | Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction withframe of 1st class hard wood and well matched commercial 3 plyveneering with vertical grains or cross bands and face veneers on bothfaces of shutters: 35 mm thick including ISI marked Stainless Steel butt hingeswith necessary screws |
| 20 | Providing and fixing in position. (as per I.S.1868/1982) Aluminium sliding window oftwo tracks with rectangular pipe having overall dimension 63.50 x 38.10 x 1.02mm at weight 0.547Kilogram/One Running Metre. and window frame bottom track section61.85x31.75x1.20mm at weight 0.695Kilogram/One Running Metre. Top and side track section 61.85 x 31.75x 1.30mm at weight 0.659 Kilogram/One Running Metre. The shutter should be of bearing bottom 40x18x1.25mm at weight 0.417 Kilogram/One Running Metre. Inter locking section 40x18x1.10mm at weight 0.469 Kilogram/OneRunning Metre. And handle section 40x18x1.25mm at weight 0.417 Kilogram/One Running Metre. and top section 40 x 18 x 1.25mm at weight 0.417Kilogram/Running metre. As per detailed drawings and as directed by Engineer in charge with allnecessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5mm thickplain glass with all required screws and nuts etc, complete. With colour Anodising with box |
| 21 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required |
| 22 | Point wiring for light/bell concealed type in min 20 mm HMS PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories |
| 23 | Wiring for plug on board with switch socket surface/concealed type, copper wiring and earthing and with modular accessories |
| 24 | Supplying & erecting mains with 3x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places |
| 25 | Supplying and erecting exhaust fan heavy duty 230 V A.C. 50 cycles 450 mm. 1400 RPM complete erected in position |
| 26 | Providing recess in brick wall suitable for erection of exhaust fan up to 450mm. sweep complete with grouting of nut, bolts, plastering and colour washing to match the colour of the wall for the wall thickness of 375 mm. |
| 27 | Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 10 ways (10 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface/flush mounted, IP 43 Protection provided on iron/GI frame |
| 28 | Supplying and erecting anodized aluminium light LED fitting (4 feet) Max. 22W with high transitivity diffuser with system lumens output of Min.2200 lumens , min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<20%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs at L70B50 including driver with end caps on provided PVC Block/wooded board with minimum 2 years warranty |
| 29 | Supplying and erecting HMS PVC conduit 32mm dia. with PVC accessories on wall/ceiling |
| 30 | Supplying, erecting & marking DP MCB 40A to 63A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board |
| 31 | Supplying, erecting & marking SP MCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board |
| 32 | Wooden Board 10\" x 15\" size duly painted and duly fitted on wall complete in all respect as per instruction of site engineer. |
| 33 | Supplying & erecting GI flexible conduit 25mm dia. conforming to I.S. With required number of couplings, bushes, check nuts etc. complete |
