|
| 1 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer\"s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum moisture resistant board |
| 2 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 3 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm |
| 4 | Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately).18 mm thick |
| 5 | Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately).25 mm thick |
| 6 | Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete.Wedge expansion typeFastener with threaded dia 10 mm |
| 7 | Providing and fixing cramps of required size & shape in RCC/ CC / Brick masonry backing with cement mortar 1:2 (1 cement : 2 coarse sand), including drilling necessary hole in stones and embedding the cramp in the hole (fastener to be paid separately).Stainless steel cramps |
| 8 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make thickness of powder coating 50 micron) or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :(A) For Fixed Portion (i) Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 9 | Items as above For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) (i) Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 10 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 11 | Cutting holes up to 30x30 cm in walls including making good the same:(i) With common burnt clay F.P.S. (non modular) bricks |
| 12 | Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. |
| 13 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 14 | Providing and fixing mild steel round holding down bolts with nuts and washer plates complete. |
| 15 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture |
| 16 | 12 mm cement plaster finished with a floating coat of neat cement of mix :1:4 (1 cement:4 fine sand) |
| 17 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.Two coats |
| 18 | Providing and Fixing waterproof Poly Carbonated Profiled Sheets of 4 mm Thickness over a metallic frame with proper finishing of approved colour and design as specified by Engineer-in-charge. Sheet should have protective guard film of 25 microns minimum to avoid scratches including transportation and should be supplied in single length or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5 x 55 mm) with EPDM Seal, complete upto any pitch in vertical/horizontal or curved surfaces excluding cost of purlins, rafters and trusses and including cutting of size and shape wherever required. |
| 19 | Supply, Fitting and Fixing of LED ceiling surface light in false ceiling including supply of all the materials, tools, etc. as per specification and direction.9 Watt Octane + Panel Mounting LED light fitting round for Corridor areas, VIP Suites and Standard Rooms |
| 20 | Supply, Fitting and Fixing of LED ceiling surface light in false ceiling including supply of all the materials, tools, etc. as per specification and direction.6 Watt Octane + Panel Mounting LED light fitting round |
| 21 | Supply, Fitting and Fixing of LED ceiling surface light in false ceiling including supply of all the materials, tools, etc. as per specification and direction.15 Watt Octane + Panel Mounting LED light fitting round |
| 22 | Supply, Fitting & Installation of 32 CH NVR 4K with all accessories in International Hostel cum Guest House of NERIWALM at Dolabari, Tezpur. |
| 23 | Supply, Fitting & Installation of CAMERA BULLET 4 MP with all accessories in International Hostel cum Guest House of NERIWALM at Dolabari, Tezpur. |
| 24 | Supply, Fitting & Installation of CAMERA DOME 4 MP with all accessories in International Hostel cum Guest House of NERIWALM at Dolabari, Tezpur. |
| 25 | Supply, Fitting & Installation of HDD 8 TB AV in International Hostel cum Guest House of NERIWALM at Dolabari, Tezpur. |
| 26 | Supply, Fitting & Installation of Best Quality CAT 6 Cable in International Hostel cum Guest House of NERIWALM at Dolabari, Tezpur. |
| 27 | Supply, Fitting & Installation of 8 PORT GIGA POE SWITCH with all accessories in International Hostel cum Guest House of NERIWALM at Dolabari, Tezpur. |
| 28 | Supply, Fitting & Installation of PVC Box in International Hostel cum Guest House of NERIWALM at Dolabari, Tezpur. |
| 29 | Supply, Fitting & Installation of RJ 45 Connector in International Hostel cum Guest House of NERIWALM at Dolabari, Tezpur. |
| 30 | Supply, Fitting & Installation of TV 55 INCH with all accessories in International Hostel cum Guest House of NERIWALM at Dolabari, Tezpur. |
| 31 | Supply, Fitting & Installation of 4 PORT GIGA POE SWITCH with all accessories in International Hostel cum Guest House of NERIWALM at Dolabari, Tezpur. |
| 32 | Supply, Fitting & Installation of EPBX 26 PORT with all accessories in International Hostel cum Guest House of NERIWALM at Dolabari, Tezpur |
| 33 | Supply, Fitting & Installation of Telephone with Display & all accessories in International Hostel cum Guest House of NERIWALM at Dolabari, Tezpur |
| 34 | Supply, Fitting & Installation of ROJET BOX with all accessories in International Hostel cum Guest House of NERIWALM at Dolabari, Tezpur |
| 35 | Supply, Fitting & Installation of MDF BOX 24 LINE with PROTOCTOR in International Hostel cum Guest House of NERIWALM at Dolabari, Tezpur |
| 36 | Supply, Fitting & Fixing of Best Quality Cable 4 Core in International Hostel cum Guest House of NERIWALM at Dolabari, Tezpur |
| 37 | Supply, Fitting & Fixing of Casing Capping 1” Size x 3 Metre in International Hostel cum Guest House of NERIWALM at Dolabari, Tezpur |
| 38 | Supply, Fitting & Fixing of PVC Gutka & Wooden Screw in International Hostel cum Guest House of NERIWALM at Dolabari, Tezpur |
| 39 | Supply, Fitting & Fixing of T, L and Other Type of Jointer in International Hostel cum Guest House of NERIWALM at Dolabari, Tezpur |
