Tender For Purchase Of Open Gym Equipment In Ward 06, Ernakulam-Kerala

Tender For Purchase Of Open Gym Equipment In Ward 06-2 CHEST PRESS CUM SHOULDER PRESS : Providing and fixing Chest press cum shoulder press FNF 016 (Make FUN PLAY ) using, minimum 100 NB GI C-class Pipe for CENTER FRAME , Minimum 40 NB & 32 NB GI B-class Pipe for MAIN FRAME , Minimum 32 NB & 25 NB GI B -CLASS Pipe for HANDLE FRAME , Minimum 32 NB &25NB &40NB GI B CLASS Pipe for CONNECTING PIPE , LLDP Rotomoulded seat with inbuilt bolts 3/8 x 1.5 for SEAT & BACK REST , Nylon 66 injection moulded BEARING CAP & PIPE CAP , fully Done by first coat of primer -jotun Brad 40-50 Micron thickness and Top coat of pure polvester powder with 70-80 micron thikness POWDER COAT including cost of concrete foundation , all materials, labour, etc all complete asper the instruction of Engineer in charge 3 LEG EXTENTION : Providing and fixing Leg extention FNF 020 (Make FUN PLAY ) using , Minimum 100 NB GI C-Class Pipe -for MAIN FRAME ,Minimum 40 NB GI pipe for FOOT REST PIPE ,Minimum 40 NB & 25 NB GI pipe for HANDLE. Minimum 25 NB & 40 NB GI B-CLASS pipe for CONNECTING PIPE ,LLDP Rotomoulded seat with inbuilt bolts 3/8 x 1.5 for FOOT REST, Nylon 66 injection moulded BERAING CAP & PIPE CAP , fully Done by first coat of primer jotun Brad 40-50 Micron thickness and Top Coat pure polyester powder with 70-80 micron thickness POWDER COAT including coast of concrete foundation all materials , labour, etc all complete asper the instruction of Engineer in charge 4 TAI CHI CUM STANDING TWISTER : Providing and fixing Tai chi cum twister FNF 021 (Make FUN PLAY ) using , Minimum 100 NB GI C-Class Pipe -for MAIN FRAME ,Minimum 25 NB GI B-CLASS Pipe for HANDLE FRAME , LLDP Rotomoulded seat with inbuilt bolts 3/8 x 1.5 for TWISTER DISC, Minimum 25 NB & 20 NB GI B-CLASS Pipe for SEATING FRAME , Minimum 80 NB GI B-CLASS pipe for SEATING FRAME STAND, Minimum 80 NB GI CLASS Pipe for TWISTER STAND , Minimum 25 NB GI B-CLASS pipe for TWISTER HANDLE FRAME, LLDP plastic-TWISTER DISC. Nylon 66 injection moulded BEARING CAP &PIPE CAP, fully done by first coat of primer- joitun Brad 40-50Micron thickness and Top Coat of pure polyester powder with 70-80 micron thickness POWDER COAT including cost of concrete foundation ,all materials,labour,etc all complete as per the instruction of engineer in- charge. 5 CYCLE : Providing and fixing Cycle - FPSPCL208 (Make FUN PLAY ) using , 25NB & 40NB GI B-Class Pipe for MAIN FRAME , 32 NB GI B-CLASS pipe for SEAT FRAME , 25NB GI B-CLASS Pipe for HANDLE FRAME , Nylon 66 injection moulded BEARING CAP & PIPE CAP , fully Done by first coat of primer - jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70-80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour, etc all complete asper the instruction of Engineer in charge 6 Leg Press (Double) -Supply and Installation of Double Leg Press having the following specifications: Dimensions: (L X W X H) = 1676 x 400 x1500 mm. Main frame - Ø 114 mm OD “B” class GI pipe. Foundation plate – M.S. round plate of Ø 250 mm & 8 mm thick. Foundations cover cap - dome shape of PP/NYLON/HDPE material. Link - is Ø 60 mm OD “B” Class GI pipe. Seat frame - Ø 42 mm OD “B” Class GI pipe. Leg Press back rest should be angled in 120-130 degree. Foot rest-cast iron 124 x 296 x 5 mm thick and M.S plate of 2 mm thick use to support it. Seat & back rest – 380 x 275 x 60 mm thick high-density polyethylene (HDPE) blow molded with M10 in-sert wall thickness 3 to 4 mm. Link connected with frame by 8 mm thick laser cutting MS profile. Top Closing cap – dome shape made by PP/ NYLON/HDPE material. Closing cap’s- PP/ NYLON/HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded at top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Bearing- use is 6005 permanent lubricated reputed brand. Pin– Ø 25 mm M.S. bright bar pin. Bearing bushes - Ø 60 mm OD seamless pipe. Circlip– A 24 circlips are used for assembly. Coating - best quality of powder coating 80-120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be welded as per IS standards and zinc primer paint should be applied at all the welding points prior to finishing.<br> 7 SIT UP BOARD made from C Class GI pipe to be use by two persons at one time. Closing Caps are made up of Low Linear Density Poly-Ethylene (LLDPE) Material with Injection Moulding. The powder coat should be Poly urethane & Epoxy powder with 60 to 70micron thickness. Dimensions: 2000mm (Length) x 1100mm (Width) x 650mm (Height). 8 Cross Trainer (Double) - Supply and Installation of Double Cross Trainer having the following specifications: Dimensions: (L X W X H) 2280 x 550 x 1650 mm. Main frame- Made of Ø 88 mm OD “B” class Gl pipe dually bending design. Foundation plate – M.S. round plate of Ø 250 mm & 8 mm thick. Paddle vertical support - Ø 42 mm OD “B” Class Gl pipe. Handle - Ø 33 mm OD “B” Class Gl pipe dually bending design. Leg movement frame – 50 mm x 50 mm x 2 mm thick square pipe. Footrest - cast iron 124 x 296 x 5 mm thick and M.S. plate of 2 mm thick use for to support it. Top Closing cap – dome shape made by PP / NYLON / HDPE material. Closingcap’s– PP / NYLON / HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD B class G.I. pipe. and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Grips - High quality rubber. Bearing- Use is 6005 permanent lubricated reputed brand. Bearing bushes - Ø 60mm OD seamless pipe. Pin – Made of Ø 25mm M.S. bright bar. Circlips – A 24 circlips are used for assembly. Coating - best quality of powder coating 80-100 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be welded as per IS standards and zinc primer paint should be applied at all the welding points prior to finishing. Please Enable Macros to View BoQ information

INR 665 /-

INR 3 Lakhs /-

FileName	File Description	File Size
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB