SPL REPAIR OF OLD VINTAGE PERMANENT INFRASTUCTURE INCLUDING STORES, SHEDS, SHELTERS, OFFICER’S MESS OR’S LIVING, TOILET CUM BATHROOM, COOK HOUSE ALONGWITH MAIN GATE NO P-1, P-18, P-26, P-34, P-37/1-6, P-38, P-40A, P-42, P-42A AND P-46 IN THE AOR OF AGE B/R II UNDER GE 969 EWS(JOB NO: GO AHEAD SANCTION UNDER PARA 35 & 38 (C) OF DWP 2020); 1 Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed. 2 M&L hardcore of gauge n exc. 63 mm, broken stone deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a truesurface complete all as specified and directed. 3 M&L for 100mm thick cement concrete 1:3:6, type C- 2 (using 40mm graded stone aggregate) as in sub base complete all as specified and directed. 4 M&L for 100mm thick cement concrete 1:2:4, type B1 (using 40mm graded stone aggregate in sub base compete all as specified and directed. 5 M&L 15mm thick screed bed or bedding layer for laying floor finishes in CM 1:4 complete all as specified and directed. 6 Non - skid ceramic colour tiles 7 to 8 mm thick area of each tile exceeding0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. 7 M&L for machine cut Kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. 8 M&L for vitrified ceramic dark shade tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. 9 M&L for vitrified ceramic light shade 10 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36sqm as in skirting over and including 10 mm thick rendering incement mortar 1:4,etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified. 10 M&L for glazed ceramic coloured tiles 300 mm x 450 mm and 7 to 8 mm thick as in vertical surfaces such as skirting, dado etc. set and jointed in neat cement slurry pointed in white or coloured cement to match over and including 15 mm thick rendering in cement mortar 1:4 to receive tiles, including dismantling floor, hearth or wall tiling including cement mortar bedding (but not baking), removing serviceable tiles to stores and rubbish of the premises complete all as specified. 11 M&L for 20 mm thick granite (of any type) work (table rubbed and polished ) in steps, jambs, pillars, window -cills, cooking platforms and like over and incl 15mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl dismantling floor, hearth or wall tiling incl cement mortar bedding (but not baking), removing serviceable tiles to stores and rubbish of the premises complete all as specified and as directed. 12 Demolition of brickwork or stone/ boulder masonry, built in cement mortar complete all as specified and directed. 13 M&L for brickwork with sub class ‘B’ bricks, straight or curved on plan to any radius, built in CM 1:6 complete all as specified and directed. 14 Taking down cement plaster on brick or stone walls, etc. hacking for key, scrubbing down with water,etc complete all as specified and directed. 15 M&L for rendering 10mm thick on fair faces with using extra cement of brick work or concrete surfaces in cement mortar 1:4 complete all as specified and directed. 16 M&L for rendering 15mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:4 including taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed. 17 M&L for preparation of untreatedconcrete wallsurfaces and applying two coats of oil bound distemper over a layer of 3mm thick wall care puttycomplete all as specified. 18 M&L for preparation of untreatedconcrete ceilingsurfaces applying two coat of oil bound distemperover a layer of3mm thick wall care putty complete all as specified. 19 M&L for preparing surfaces, plastered or unplastered new surfaces on wall and applying two coats of cement base paint complete all as specified and directed. 20 M&L for walling of random rubble, uncoursed well bonded, bedded and solidly hearted as in built cement mortar 1:4 complete all as specified and directed. 21 M&L for keyed pointing to random or polygonal rubble, uncoursed or brought upto course including raking out joints/ pointing to brick work in walls or to bricks on edge in floors, surface channels, roofs, etc. complete all as specified and directed. 22 M&L for 75mm thick PCC 1:3:6, type C2 (using 20mm graded crushed stone aggregate) as in plinth protection etc. finished even and smooth with using extra cement and making joint & filled with maxtric complete all as specified and directed. 23 M&L forming 6mm thick expansion joints filled with pre formed bituminous filler and top 30mm primed and sealed with sealing compound grade A . 50mm deep complete all as specified and directed. 24 Dismantling boarding, any description, fixed inany position with nails complete all as specifiedand directed. 25 M&L for 2nd class softwood clean sawn boards or planks, width n exc. 25 cm as use in eaves board complete all as specified and directed. 26 Providing & fixing false ceiling atall heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non-combustible as per BS 4 76 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of s1ze 600x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e. 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1 Odom length and Lshape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450mm tiles fully centre to centre and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in Charge.(a) n with semi perforated 12mm thick micro tengular edged GRG false ceiling tiles. 27 Demolition for wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed. 28 M&L plain fillets, Square rectangular or triangular in section, clean sawn Exc 13& n.exc 25 sqm 2nd class hardwood, secured with nails or brads including dismantling timber framed scantlings under 40 sq. cmin section, in any position complete all as specified and directed. 29 M&L veneered decorative plywood, 4mm thick grade 1 (with BWR resin) with decorativeface veneers on single faces; fixed to wall with screws to timber frame work complete all as specified and directed. 30 M&L for plywood 6mm thick, grade BWP, type BB fixed in wall with screws to timber frame work complete all as specified and directed. 31 M&L veneered decorative plywood, 4mm thick grade 1 (with BWR resin) with decorativeface veneers on single faces fixed to ceiling with screws to timber frame work.complete all as specified and directed. 32 M&L for plywood 6mm thick, grade BWP, type BB fixed to ceiling with screws to timber frame work complete all as specified and directed. 33 Taking down chowkhats or frames n exc 1.5 sq. m each but with shutters (without taking off shutters from the frame) complete all as specified and directed. 34 S&F for steel work such asin hold fasts conforming to similar articles Fe-290 Gde E-165, complete all as specified. 35 M&L for PCC 1:2:4, type B1 (using 20mm graded stone aggregate) as in hold fasts/ bed blocks/ coping etc. complete all as specified. 36 S&F for solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed. 37 S&F for factory made solid PVC door shutter moulded with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed. 38 Taking down chowkhats or frames exc 1.5 sq. m but n exc 4 sq. m each but with shutters (without taking off shutters from the frame) complete all as specified and directed. 39 M&L for plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints, supplied and fixed 2nd class softwood complete all as specified and directed. 40 S&F plain, framed, factory made panelled shutters (any number of panels), with panels 2nd class hardwood (35mm) thick of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers supplied and fitted to chowkhats complete all as specified and directed. 41 M&L for glazed and skeleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, section 8, clause 8.24 (a) supplied and fitted to chowkhats complete all as specified and directed. 42 S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. 43 Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed. 44 M&L for sheet glass 3mm thick ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane including hacking out old broken glass complete all as specified and directed. 45 S&F butt hinges 75mm long, medium weight, cold rolled mild steel, and fixed complete all as specified and directed. 46 S&F butt hinges 100mm long, medium weight, cold rolled mild steel, and fixed complete all as specified and directed. 47 S&F foraluminium handles 150mm long, cast type, stove enamelled black complete all as specified and directed. 48 S&F for aluminium anodised, barrel tower bolts 100mm long of extruded section and fixed complete all as specified and directed. 49 S&F foraluminium handles 100mm long, cast type, stove enamelled black complete all as specified and directed. 50 S&F for aluminium alloy 150mm long, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. 51 M&L forpainting on newly wooden surfaces with two coats of synthetic enamel paint over one coat of pink primer of any description, not otherwise described, over 10cm width or girth complete all as specified and directed. 52 Dismantling timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed. 53 M&L for second class soft-wood clean sawn in scantlings complete all as specified and directed. 54 Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed. 55 S&F for pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa asin roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. 56 S&F for fibre glass reinforced translucent corrugated sheeting 2mm thick with two corrugations side lap fixed with coach screw and washer in roof, wall etc. complete all as specified and directed. 57 S&F for galvanised, corrugated mild steel sheeting with two corrugations sidelap 0.63 mm thick, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 complete all as specified. 58 S&F for plain, galvanised, mild steel sheeting 0.80mm thick, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinccoating 275 complete all as specified and directed. 59 M&L for painting newly steel plain surfaces of any description, over 10cm in width or girth, not otherwise described two coat of synthetic enamel paint over one coat of primer complete all as specified and directed. 60 Taking up or down steel tubing and connections of 15mm bore in pipe, including cleaning for re-fixing or removal from site complete all as specified and directed. 61 S&F in repair steel tubes, 15 mm bore, with screwed socket joints, galvanised, medium grade with all fittings and fixtures, fixed to wall and ceiling or laid in floor, including necessary changing and cutting in brick/concrete surfaces and making good the disturbed surface in cement mortar 1:4 complete all as specified. 62 S&F for 3-layer PP-R polypropylene random copolymer) concealed pipes 20mm outer dia SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and directed. 63 Taking up or down steel tubing and connections of 20mm bore in pipe, including cleaning for re-fixing or removal from site complete all as specified and directed. 64 S&F in repair steel tubes, 20 mm bore, with screwed joints ,galvanised, medium grade with all fittings and fixtures , fixed to wall and ceiling or laid in floor, including necessary changing and cutting if required in brick/concrete surfaces and making good the disturbed surface in cement mortar 1:4 complete all as specified. 65 S&F for 3-layer PP-R polypropylene random copolymer) concealed pipes25mm dia SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and directed. 66 S&F in repairs vitreous china wash down water closet pan (Odissa pattern), white, including connection to drain (or outgoing pipe) and flushing pipe, antisyphonage pipe etc. complete all as specified. 67 S&F in repair for PVC valveless, symphonic action type,10 litersflushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and PVC connection complete all as specified and directed. 68 S&F in repair for flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern complete all as specified and directed. 69 S&F in repair for 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. 70 S&F in repair vitreous china wash hand basin white flat back of size 550mmx440mm including CI brackets, chromium plated waste coupling, waste pipe etc., (including all waste fittings) complete all as specified. 71 S&F in repair stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm complete all as specified and directed. 72 S&F waste coupling 32mm or 40mm CP for glazed ware sinks, basins, etc. with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified. 73 S&F in repair 75 mm out let cast iron floor trap with CP grating including jointing to waste pipe fixed in cement concrete 1:2:4, complete all as specified. 74 S&F in repairs 100 mm dia PTMT grating doom (minimum weight 25 gms), all as specified. 75 S&F in repairs chromium plated shower roseswith or without swivel joints, anysize, including fixing to steel pipe or union complete as specified and directed. 76 S&F in repair soap dish any type fixed to plugs with chromium plated brass screw, complete all as specified. 77 S&F in repair pillar taps 15 mm dia, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed. 78 S&F in repair plug type bib taps 15 mm dia, cast iron, screwed for iron pipe and fixed complete all as specified and directed. 79 S&F in repair stop valves 15 mm dia, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. 80 Demolitionandbreaking up drain pipes(salt glazed ware or AC/PVC ) set incementmortar 100mm/ 75 mm internal dia of pipe complete all as specified and directed. 81 S&F 75 mm PVC (SWR) bends branch piece, single Y equal or un equal with access door etc. complete all as specified and directed. 82 S&F for 75 mm PVC (SWR)pipes single socketed, in any length with rubber ring joint, laid in trenches or in floors complete all as specified. 83 S&F 110mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches etc. complete all as specified. 84 S&F 110 mm PVC (SWR) bends branches piece, single Y equal or un equal with access door etc. complete all as specified and directed. 85 Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft soil complete all as specified and directed. 86 S&F in repair for floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor 150mm complete as specified and directed. 87 S&F in repair door closer hydraulically regulated, designation No. 2, universal type, suitable or door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed aluminium (extruded section body) complete as specified and directed. 88 S&F in repair vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern including all necessary accessories like rag bolts/ gel gasket etc. (including 15ltr flushing cistern & flush pipe 32mm dia ) complete all as specified. 89 S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified. 90 Dismantling water tanks and removing to store exc 250 & n.exc 500 ltr complete all as specified and directed. 91 S&F rotational moulded triple layered polyethylene water storage tanks 500ltr (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete as specified and directed. 92 S&F rotational moulded triple layered polyethylene water storage tanks 1000ltr (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete as specified and directed. 93 S&F in repair toilet paper holder with flat recessed type stainless steel complete all as specified and directed. 94 S&F in repair bib taps, 15mm dia cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed. 95 S&F in repair hasp and staple, mildsteel, wire type, stove enamelledblack, including bolt to hingeplate and fixed with screws complete all as specified. 96 S&F in repair tubular towel rail, aluminium anodised 20mm dia, D type, 60cm long between flanges complete as specified and directed. 97 S&F in repair Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc., complete all as specified. 98 S&F framed work as in doors or gates of angle Fe 410 -W (Gde- E- 250) quality- A other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete all as specified and directed. 99 Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed. 100 S&F in repair brass CP wall mixer for mixing hot & cold water screwed down for iron pipe 20mm bore dia and fixed complete all as specified and directed. 101 M&L for 18/19mm thick Block boards, grade 1quality, exterior grade,commercial type, fixed with screws to timber complete all as specified anddirected. 102 S&F decorative laminates type I, 1.5mm thick (High Glossy Finish), or surfacefinish, colour and pattern as approved by GE complete all as specified anddirected. 103 S&F in repairs 40 mm continuous (Piano) hinges, mild steel , bright finish or electro galvanised complete all as specified. 104 S&F in repairs 150 mm extruded brass handles, fabricated type polished complete all as specified and directed 105 S&F in repairs 50 mm brass Lock, cupboard, Grade I in 2 levers complete all as specified and directed 106 M&L PCC 1:2:4 type B-1, (using 20 mm graded stone aggregate) as in levelling course/benching, fixing of spouts pipes in sunken portion/ base water tank, complete all as specified and as directed. 107 M&L for water proofing treatment to toilets slabs including wall with a coat of epoxy coating of make Dr Fixit/Pidilite/Phoscok/silka as per manufacturers instruction including ponding test complete all as specified and directed. 108 M&L applying two coat of bitumen 85/25grade on floor and vertical portion at the rate of 1.2 kg/sqm including cleaning of surface complete all as specified. 109 Demolition of cement concrete above ground floor exc 15 cm thick complete all as specified and directed. 110 M&L for rendering 5mm thick in CM 1:3 on ceiling surfaces complete all as specified and directed. 111 S&F 30mm thick glazed andskeletonshutters, openrebated and preparedto receive glass,gauze, etc. (withsash bars),edges offraming plain,chamfered orrounded fitted withcut and mitred beadsfor securing glass, etc., sizes of membersof shutters asspecified inSSR PartI, section 8, clause8.24 (a) supplied andfitted to chowkhats complete all as specified. 112 M&L preparation of old painted surfaces ofany description, not otherwisedescribed, over 10cm width orgirth and applying one coat of synthetic enamel paint complete all as specified and as directed. 113 S&F in repair centre hole basin brass CP mixer for mixing hot & cold water screwed down for iron pipe 20mm bore dia and fixed complete as specified and directed. 114 M&L providing, precast cement concrete 1:2:4, type B1 (using 20 mm graded stone aggregate) as in manholes cover slab, etc.(of any section indicated), with plain fair faces, including chamfers weathering, throating etc. and setting in mortar complete with joints to match complete all as specified. 115 M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified. 116 M&L for concrete bed to drain pipes in PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) including packing under haunching against the sides of pipe after they are laid and tested for 150mm dia complete all as specified. 117 M&L for cutting in to existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for as specified dia of pipe 150mm complete all as specified. 118 M&L reinforced concrete pipes 150mm dia,class NP3, laidand jointed with collars complete all as specified. 119 Excavation in trenches n exc 1.5 m wide and n exc 1.5 m deep for foundation, etc. or for shafts, wells, manholes etc. n.exc 10 Sqm on plan and getting out soft or loose soil complete all as specified and directed. 120 Returning filling in including spreading levelling, watering and well ramming in layers n exc 25 cm of loose and soft soil complete all as specified. 121 Removing excavated materials n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified. 122 S&F 110 mm bore PVC (SWR) junction single (Single T) equal of unequal, all as specified. 123 S&F 75 mm bore PVC (SWR) junction single (Single T) equal of unequal, all as specified. 124 S&F 75 mm bore PVC (SWR) vent cowl complete all as specified and directed. 125 S&F 110 mm bore PVC (SWR) vent cowl complete all as specified anddirected. 126 S&F cross arms, bracings, supports,clamps and back plates fabricatedfrom structural steel sectionsincluding nuts, bolts, washers,welding, bending cold or hot,drilling holes for bolts, in any shapeor size as indicated or directed including of one coat of primer and oneunder coat and one finishing coat of paint complete all as specified. 127 S&F framedworksuch as grills,gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes framedguard bars, barred iron doors,ladders, framedbalusters, walkways, railings,framework ofwater tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. 128 S&F 300 mm size mild steel ordinary rat rail rod pattern springs including roller and roller plate complete all as specified. 129 S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified. 130 S&F sinks with drainage boardmade of stainless steel 1mm thick kitchen or laboratorywith plugs,washers and wastes; includingbedding in cement mortar to dwarfwall or including fixing cantileverbrackets and connecting union topipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160m complete all specified and directed. 131 S&F plastic water closet seat, black, closed pattern withflat bottom, and cover and mild steel chromiumplated or aluminised hinging device complete all as specified and directed. 132 S&F in repair 15 mm bore angular stop valve cast copper alloy screwed down high pressure with crutch butter fly handle screwed both ends for iron pipe or for unions and fixed all as specified. 133 S&F in repair PVC connection 15 mm size with PTMT nuts of length 600 mm of approved quality complete all as specified and directed. 134 S&F in renewal of 20mm bore gun metal gate valves, with iron wheel head, screwed both ends suitable for iron pipe complete all as specified. 135 S&F in repairs 20 mm ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed(minimum weight 20mm - 210 gms) etc. complete all as specified. 136 Dismantling structural steel work including doors gates etc. complete all as specified and directed. 137 Demolition of concrete of any description and in any position not otherwise specifically provided for cement concrete (unreinforced) complete as specified and directed. 138 Excavating in trenches, n.exc. 1.5m wide and n.exc. 1.5 m in depth, for foundation, etc. or for shafts, wells, cess pits, manholes, pier holes, etc. n.exc. 10 sqm on planand getting out hard/dense soilcomplete all as specified and directed. 139 M&L for cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregates) as in foundation, filling and mass concrete all as specified and directed. 140 M&L for RCC M-25 Design Mix using 20 mm graded stone aggregate in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc. basement slabs and mass concrete all as specified. 141 M&L for RCC M-25 Design Mix using 20 mm graded stone aggregate in columns, pillars, piers, posts and struts complete as specified and directed. 142 Demolition of brickwork or stone/ boulder masonry, built in lime mortarincluding allquoins, arches, pillars, etc., but excluding ashlar facings, dressed stonework and precast concrete articles built in cement motor complete as specified and directed. 143 M&L for old size brickwork with sub- class ‘B’ bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:4 complete all as specified anddirected. 144 M&L for rendering 10mm thick in cement and sand mortar 1:6 on fair faces of brick work or cement concrete surfaces admixed with water proofing compound including finishing the surface even and smooth without using extra cement, complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately. 145 M&L for form work to sides of flat, rough finished surfaces of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical to batter complete all as specified. 146 M&L for form work to sides of square, rectangular or polygonal, rough finished surfaces of concrete of pillars, posts, struts, piers, columns and stanchions complete all as specified. 147 M&L for mild steel TMT bars 5 mm dia and over up to and including 10 mm dia in stirrups, spacers and binders, cut to length, bent to shaperequired including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified. 148 S&F rolled mild steel of grade Fe-290 (Grade E-165) in framed work as in doors or gates of angle or other section with gusset plates, rails braces, etc. complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified. 149 M&L for 20 mm thick granite ( of any type) (table rubbed and polished ) in steps jambs ,pillars, window cill, cooking platform and like in cement mortar 1:4 including pointingin white cement 1:2 using marble dust with admixture of pigment to match with shade of granite over and including 10 mm thick rendering on concrete surface in CM 1:4 complete all as specified. 150 M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified. 151 S&F aluminium composite panel 3 mm thick of Euro bond ALSTONE with necessary steel frame work as in gates, pillar projections etc. including taping joints as per manufactures instructionscomplete all as specified and directed. 152 S&F brass letters 30cm height and 30cm in letter width as in emblem fixing to wall with all necessary fittings, drilling, fixing with hexagonal bolts, finish as specified includingbrass polishing, glazed finish and fix complete all as specified. 153 Taking down carefully copper/aluminium point wiring (light. Fan, socket or power) complete, including fittings such as switches, ceiling roses, pendants, regulators, sockets etc, removing materials to store for keeping in safe custody for reuse at site and making good disturbed surfaces of walls, floors etc. to match with existing surfaces complete all as specified and directed. 154 M&Lfor point wiring inPVC casing capping with 1.5 Sqmm size multi stranded FRLS copper conductor cable 1.5 Sqmm including clamps, screws gutter/plug etc PVC unsheathed cable into and including wooden board with bakelite sheet and PVC insulated FRLS cable of size 1.5 Sqmm as earth continuity conductor one light point/fan point/ex fan point controlled by one 5 Amps switch one way complete all as specified and directed. 155 All as per ser item No 155 here-in-before but one 3 pin 5 Amp switch socket outlet on independent board 156 All as per ser item No 155 here-in-before but one 3 pin 5 Amp switch socket outlet on same board with accessories 157 M&Lfor point wiring in PVC casing capping with 2.5 Sqmm size multi stranded FRLS copper conductor cable including clamps, screws gutter/plug etc PVC unsheathed cable into and including wooden board with bakelite sheet and PVC insulated FRLS cable of size 2.5 Sqmm as earth continuity conductor complete all as specified and directed. 158 S&F switch piano flush type, single pole, one way 6 Amps 240 Volts, complete all as specified and directed. 159 S&F switch piano flush type, single pole, 15 Amps 240 Volts, complete all as specified anddirected 160 S&Fsocket outlet 2 in 1, 3 pin, 5 Amps, flush type with gang box complete all as specified and directed. 161 S&Fsocket outlet 2 in 1, 3 pin, 5 and 15 Amps, flush type with gang box complete all as specified and directed. 162 M&L for point wiring using proper colour coding complete with 1100 Volts grade 1.5 Sq.mm, single core, PVC insulated, unsheathed cable with multistranded copper conductor with ISI mark FRLS grade, conforming to IS-694 in and including PVC medium grade conduit not less than 25mm dia. ISI marked with all accessories concealed in wall/ceiling/ floor /roof etc,sunk pressed steel/GI terminals boxes having 1.6 mm thick suitable for housing of modular type switches/sockets/fan regulators, including 1.5 Sq.mm PVC insulated, unsheathed, multistranded copper conductor, FRLS 1100 volts grade (green colour) as earth wire, connected to common earth dolly for one light point/fan point/Ex fan point controlled by one 5 Amps switch one way complete all as specified and directed. 163 All as per ser item No 163 here-in-before but one three pin switch socket 5 amps outlet on same board. 164 All as per ser item No 163 here-in-before but one three pin switch socket 5 amps outlet on independent board. 165 All as per ser item No 163 here-in-before but one bell/buzzer point controlled by one switch 166 M&L for point wiring using proper colour coding complete with 1100 Volts grade 2.5 Sq.mm, single core, PVC insulated, unsheathed cable with multistranded copper conductor with ISI mark FRLS grade, conforming to IS-694 in and including PVC medium grade conduit not less than 25mm dia. ISI marked with all accessories concealed in wall/ceiling/ floor /roof etc, withsunk pressed steel/GI terminals boxes having 1.6 mm thick suitable for housing of modular type switches/sockets/fan regulators, including 2.5 Sq.mm PVC insulated, unsheathed, multistranded copper conductor, FRLS 1100 Volts grade (green colour) as earth wire, connected to common earth dolly for switch socket combination, 3 pin, 15 Amps on independent board all as specified and directed. 167 S&Fmodular type switch 6 Amps, one way one module complete all as specified. 168 S&F modular type Socket outlet, 6 Amps,2/3 pin combined 2 module complete all as specified. 169 S&F modular type docket outlet, 6/16 Amps, combined 2 module complete all as specified. 170 S&F electric bell, ding dong AC 230Volts, single pole complete all as specified and directed. 171 S&Fmodular bell push 6 Amps, modular type complete all as specified. 172 S&F modular stepped type fan regulator,120 Watt - 2 modulecomplete all as specified and directed by Engr-in-Charge. 173 M&L forwhite cover with framesuitable for accommodating 01 module switch/socket etc complete all as specified and directed by Engr-in-Charge. 174 M&L for white cover with frame suitable for accommodating 02 module switch/socket etc complete all as specified and directed by Engr-in-Charge. 175 M&L for white cover with frame suitable for accommodating 03 module switch/socket etc complete all as specified and directed by Engr-in-Charge. 176 M&L forwhite cover with framesuitable for accommodating 4 module switch/socket etc complete all as specified and directed by Engr-in-Charge. 177 M&L forwhite cover with framesuitable for accommodating 6 module switch/socket etc complete all as specified and directed by Engr-in-Charge. 178 M&Lforwhite cover with framesuitable for accommodating 8 module switch/socket etc complete all as specified and directed by Engr-in-Charge. 179 S&F ceiling rose 3 terminal / PVC/ Polycarbonate, isolated body all as specified and directed 180 S&F in repairs distribution Board, SPN 4 Way, double door complete all as specified and directed. 181 S&F in repairs distribution Board, SPN 8 Way, double door complete all as specified and directed. 182 S&F in repairs distribution Board, TPN 4 Way, double door complete all as specified and directed 183 S&F in repairs MCB,DP 40 Amps 240 VoltsB curve, complete all as specified and directed 184 S&F MCB single pole 6-32 Amps 240 Volts B Curve complete all as specified and directed 185 S&F MCCB 4 Pole 63 Amps, 16 KA, 415 Volts complete all as specified and directed 186 S&F LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose all as specified and directed. 187 S&F LED luminaire 600 mm x 600 mm, 35/36 Watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. 188 S&F LED light fitting 1x10 bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size all as specified and directed. 189 S&F LED bulb 12 W, 220V suitable size from ceiling rose all as specified and directed 190 S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 Watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. 191 S&F lamp holder, PVC/ Polycarbonate type with back plate suitable for batten fitting complete all as specified and directed 192 S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet complete all as specified and directed. 193 S&F in repair capacitor 1.5/2 MFD suitable for 1200mm sweep ceiling fan complete all as specified and directed by Engr-in-Charge. 194 S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding of sweep 300m complete all as specified and directed. 195 S&F ceiling fans, complete with three blade, down rod, accessories 230V, 1200mm sweep, with squirrel cage induction motor complete all as specified and directed. 196 S&F XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 sq. mm 4 core complete all as specified and directed. 197 S&F 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular of 16 sqmm size complete all as specified and directed. 198 M&L sub main wiring with two run single core 6 Sqmm FRLS copper conductor cable PVC insulated, unsheathed, 1100 V including 20 mm diaPVC conduit/casing capping, medium grade ISI marked with all accessories such as Tees, elbows, junction boxes etc, as required fixed on wall alongwith one run of 6 Sqmm single core PVC FRLS insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board / distribution board and testing on completion etc complete all as directed.Note: Two runs of 6 sqmm and one run of 6 sqmm cable and one run of casing capping shall be measured as one RM 199 Taking down and dismantling the ceiling fan from site and removing its allied smaller parts for cleaning, servicing, oiling and lubricating and replacement of unserviceable parts such as bearings, bushes, etc and refixing the same fan in its original position with all the parts i.e. down rod, canopies, fan blades, spilt pins, screws, nuts and spring washers complete including, flexible chord of 24 / 0.20mm with necessary connector (for blade / body) as required after rewinding complete all as specified and directed. Note : Cost of spares used and rewinding shall be deemed included in quoted rate. 200 M&L in repairs for earthing complete with galvanizedsteel earth plate electrode 600mm x 600mm and 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanized earth wire of 4 mm dia (up to 7.5 m in length from earth plate ) by means of bolts and nuts checknuts and washers of galvanized iron or steel all as specified and shown in electrical plate No.3 of SSR part I -2009 including necessary excavation and earth work in any type of soil PCC 1:3:6 type C1 chamber with RCC 1:2:4, type B1 40 mm thick cover with MS rod 8mm dia at 150mm c/c in both ways as reinforcement, watering funnel, 20 mm dia light grade for protection of earth electrode, 20 mm dia GI pipe light grade for watering complete all as specified and as directed by Engineer in charge and tested on completion. Note : The rate is inclusive of necessary earth work, RFR and removal etc
