Tender For Repair/Maintenance To Joinery, Roof Sheets, Sanitary Fittings, Cooking Platform, Plastering And Welcome Maintenance To Md Accommodation Including Misc B/R Works At Afs Madh Island Under Ge Af Thane; 1 Demolition of cement Concrete of any description and in any position not otherwise specifically provided for, complete all as specified. 2 Demolition of brickwork or stone/boulder masonry, built in cementmortar including all quoins, arches, pillars, etc., but excluding ashlar facings, dressed stonework and precast concrete articles including removing of rubish, complete all as specified and as directed by Engineer-in-Charge. 3 Taking down cement plaster, of any description on brick or stone or cement concrete walls/ceiling including raking out joints, hacking for key, scrubbing down with water, complete all as specified and as directed by Engineer-in-Charge. 4 M&L for brick work with subclass B bricks, straight or curved on plan exceeding6 m mean radius, built in cement mortor 1:4, complete all as specified and as directed by Engineer-in-Charge. 5 M&L for rendering 15 mm thick, on fair faces of brick or concrete surfacesin cement mortar 1:4 by using water proofing compound as per manufacturer instruction and surfaces finishedeven and smooth without using extra cement, complete all as specified and as directed by Engineer-in-Charge. Note:- WPC will be measured and paid separately. 6 Supply only integral water proofing compound, complete all as specified and directed. 7 S&F in repair PVC (SWR) Nahani trapof dia 75mm with grating including jointing with solvent cement ,complete all as specified and directed. 8 S&F in repair 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls and fixedcomplete all as specified. 9 S&F in repair 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls and fixed, complete all as specified. 10 S&F in repair PVC SWR bends of 110mm bore, complete all as specified and directed. 11 S&F in repair PVC SWR bends of 75mm bore, complete all as specified and directed. 12 S&F in repair PVC SWR branch piece (double Y) equal or unequal 75 mm bore and provided with access door , complete all as specified and directed. 13 S&F in repair PVC SWR branch piece (double Y) equal or unequal 110 mm bore and provided with access door , complete all as specified and directed. 14 Taking down chowkats or frames n.exc 1.5 sqm with shutters without taking off shutters from the frame, complete all as specified. 15 Taking down chowkats or frames exc 1.5 sqm & n exc 4 sqm with shutters without taking off shutters from the frame, complete all as specified. 16 Taking down shutters of any description exc 1 sqmbut n.exc 2 sqm, complete all as specified. 17 Resecuring or easing & adjusting without taking down shutters of any description exc 1 sqm and n.exc 2 sqm, complete all as specified. 18 Taking down shutters of any description exc 1 sqmbut n.exc 2 sqm and refixing in the same openingafetr easing & adjusting of wooden shutter, complete all as specified. 19 M&L for 2nd class hardwood (SAL) plain, solid, straight chowkats and frames, wrought frames rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified. 20 S&F 2nd class HW 35mm thick plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats, complete all as specified. 21 S&F 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, both face is covered with decorative face veneer with lipping/frame to match complete all as specified. 22 S&F 2nd class hard wood 30mm thick glazed and skeleton shutters to chowkats, open, rebated and prepare to reveive glass, guage etc (with sash bars any numbers) edges of framing plain chamfered or rounded, fitted with out mitred beads for securing glass etc, size of members of shutters as specified supplied and fitted to chowkats complete all as specified. 23 S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm (double door chowkate) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as specified.Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 24 S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 100 mm (double door chowkate) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as specified.Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 25 S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. Note:- (i) stainless steel butt hinges shall be paid separately(ii) cost of necessary S S screws shall be included in quated rate. 26 S&F 30mm thick factory made wiremesh solid WPC door shutter consisting ofDensity 600 Kg /CbmManufactured by an ISO-9001-2015 certified Company , Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose.(confirming as per IS:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos.hinges hingesand 32mm long steel screws drilled suitable to pass through both the walls of the M.S tube.Other hardwares should be fixed with 19x6mm size steel screws etc. Complete as per direction of manufacturers specification & drawings. 27 S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Squar tube, suppling & fixing in opening as per specification & drawing. 28 S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. 29 S&F PVC factory made wire gauged shutter with wire gauge warpped on an additional square 8mm MS solid tube and this tube shall be welded to MS tube. The wires gauge shall be stretched to tighten firmly, PVC door shutter 30mm thick (stiles) consisting of frame made out of MS tube for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC C channel having a PVC sheet strip of 20mm wigth stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail all as per specification and drawing given in SSR Part II, Schdule of rates 2010 and directed but as in four panels in lieu of two panels. Note : The wire mesh shall be measured separately. 30 S&F MS bands, straps, supports of stays, hold fast, wall ties etc and similar articles etc confirming to Fe-410-310m complete all as specified and directed by Engr-in-Charge. 31 M&L for cutting holes in bricks walls built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar or cement concrete 1:2:4 type B1 as required exc half brick but not exc one brick complete and as directed. 32 M & L for providing cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs complete and as directed. 33 M & L for preparation of new wooden surfaces and apply two coats of synthetic enamel paint over a coat of pink primer, complete all as specified. 34 M&L for rendering 15 mm thick, on fair faces of brick or concrete surfacesin cement mortar 1:6surfaces finishedeven and smooth without using extra cement, complete all as specified and as directed by Engineer-in-Charge. 35 M&L preparing newly plastered surfaces ,and applying 2 coats of Oil Bound Distemper over a coat of alkali resistent primer on walls complete all as specified. 36 S&F 100mm sizeButt hinges, extruded stainless steel hinge pin, anodised and fixed, complete all as specified. 37 S&F 150mm long aluminium anodized barrel tower bolts of extruded section, complete all as specified. 38 S&F aluminium extruded alloy handles fabricated type anodized 150mm long, complete all as specified. 39 S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified. 40 S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified. 41 S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified. 42 S&F as in repairs 100mm sizeButt hinges, extruded stainless steel hinge pin, anodised and fixed, complete all as specified. 43 S&F as in repairs 150mm long aluminium anodized barrel tower bolts of extruded section, complete all as specified. 44 S&F as in repairs aluminium extruded alloy handles fabricated type anodized 150mm long, complete all as specified. 45 S&F as in repairs250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed. 46 S&F as in repairs Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified. 47 S&F as in repairs Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified. 48 Hacking out broken glass any thickness size quality or description form wooden, concrete, aluminium steel frames glazed with oil putty fixed with nails. 49 S&F for ordinary sheet glass 3mm thick and glazing with oil putty/beddings in square n exc 0.5 sq, in each panes as directed by Engr-in-Charge 50 S&F for ordinary sheet glass 4.8mm thick and glazing with oil putty/beddings in square exc 0.5 sq, in each panes as directed by Engr-in- Charge 51 S&F 3mm thick Figured glass, pin head type and glazing in squares n exc 0.5 sq. m in each pane/ as in aluminium louvers, complete all as specified. 52 S&F in repairs aluminium body door closer hydraulically regulated designation No 3 universal type, suitable for door shutter of 851mm to 1000mm in width and wt. between 61 to 80 kg, complete all as specified. 53 S&F as in repairs 300mm mild steel helical door spring including roller plate complete all as specified and directed. 54 Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc, complete all as specified. 55 M&L for machine cut cuddappa stone slab 20 to 25 mm thick as in cills/jambs of window & door openings, set jointed and pointed in neat cement slurry with grey cement slurrymixed with pigment to match the shade of the slab incl rubbing and polishing complete including 15mm thick backing coat in cement mortar 1:4 complete all as specified. 56 Taking down the unserviceable Aluminium glass door shutter of any size and description and refixing the same after resecuring the shutter by using aluminium L section at the joints and refixing the glass in the shutter complete all as specified and directed.Note :- All accessories required for repairs shall be measured seperately under other respective items. 57 Taking down aluminium sliding windows of any description and any size and repalcing the wornout , broken wiremesh, aluminium sections, glass, grill,, rubber beading, rollers, locks, etc as required and refixing back into the same opening for easy movement of shutters including necessary fittings and fixtures. Note : items such as wirmesh, Glass, grill, rubber beading, rollers, locks, aluminium section etc will be paid seperately under respective items as supply only. 58 S&Fpowder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sectionscomplete all as specified and directed by Engr-in-Charge. 59 S&F for powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions complete all as specified and directed by Engr-in-Charge. 60 Supply only PVC Star lock for Aluminium windows. 61 Supply only Nylon / PVC Rollers for Aluminium Windows. 62 Supply only Rubber beeding suitable for aluminium door/window shutters. 63 S&F as in repairs double action floor spring hydraulically operated made up of miniumum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass other parts made of mild steel heavy duty complete all as specified. 64 S&Fin repairs plain black mild steel sheet of 1.00 mm thick as in hood of the rolling shutter all as specified and directed by Engr-In-Charge. 65 S&F Steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, haspand staple and one shop coat of primer; erected in position as indicated, complete push pull or manual type , including taking down old shutter. complete all as specified and directed. 66 M & L for preparation of new treated steel surfaces of any description over 10 cm width & girth not otherwise described and applying two coat of epoxy paint over a coat of primer complete all as specified and directed. 67 S&F safety lever locks mild steel with 4 levers for rolling shutters , complete all as specifeid. 68 S&F as in repairs ball bearing for rolling shutter, complete all as specified. 69 S&F as in repairs Prelaminated particle board 18/19mm thickness, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified. 70 S&F as in repairs Hasp and staple 100mm size mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws, complete all as specified. 71 S&F as in repairs curtain rods mild steel, chromium plated with fixing brackets, stops, rollers etc including brackets, complete all as specified 72 S&F as in repairs Solar control film 50 micron reflective type sticked to glass panes as per instructions of manufacturers, complete all as specified. 73 Dismantling wrought iron or mild steel work of any description not otherwise provided, complete all as pecified. 74 S&F for Framed brackets of angles,purlins, crane gantries, rails andfastenings and heavy bracketframing (Beam, tee, angle, channelor flat sections) includingdistance pieces, cleats etc., conforming to Fe.290.Gde-E-165, complete all as specified. 75 S&F Joist, channel, angle, or tee sections, vertical posts, etc. confirming to Fe 410- W (Gde- E-250) quality -A, complete all as specified. 76 S&F rolled sections as in main & cross beams , columns, hip and jack rafters , purlins where connected to common rafters and running rails & any other places with angles cleats or other connected plates, wind ties etc confirming to Fe 410 -W (Gde-E-250) quality A, complete all as specified. 77 S&F plates (plain or chequered ) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attahment,confirming to Fe 410 -W (Gde-E-250) quality A, complete all as specified. 78 Dismentling Plain or corrugated steel sheeting,any gauge, thickness, includingNainital or similar pattern roof coverings, complete all as specified. 79 Supply and fix Pre-painted Galvalume Aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws allas specified. 80 Supply and fix Pre-painted Galvalume Aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to walls, fixed with self tapping screws allas specified. 81 Excavating in post holes (or similar holes) each n.exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified. 82 Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level), complete all as specified. 83 M&L for cement concrete in 1:2:4 type B2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete, complete all as specified. 84 M&L preparation of new steel surface synthetic enamel paint of two coats in any description, over 10 cm in width or girth, not otherwise described, over a coat of Red oxide, zinc chrome complete all as specified and directed. 85 Removing existing water proofing treatment what so ever exist (except concert padding) and removing debris/ rubbish materials off the site complete all as specified and directed. 86 M&L for APP modified roof treatment over existing RCC roof with following specification :-(a) Applying bitumen primer @ 0.4 Liters/Sqm with density of 0.87 to 0.89 Kg/Liters at 25 degree C on the prepared dry roof surface.(b) Laying 3 mm thick APP membrane weight not less than 3.50 Kg/Sqm by torch application with minimum 10cm side lap and 15cm end lap.The laying of membrane shall be done through an authorised applicator of manufacturer of APP membrane. 87 M&L for rendering 10 mm thick onconcrete surfacesin cement mortar 1:4 by using water proofing compound as per manufacturer instruction and surfaces finishedeven and smooth without using extra cement, complete all as specified and as directed by Engineer-in-Charge. Note:- WPC will be measured and paid separately. 88 Taking down rain water pipes/PVC pipes/cemented pipe (any size or pattern) including all fittings, heads, shoes, bends, swan necks, etc.,& including scaffolding, complete all as specified. 89 Fixing only old 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls, complete all as specified. 90 Fixing only old 110mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls, complete all as specified. 91 S&F 75mm PVC (SWR) bends any radius provided with access door fixed to pipe , complete all as specified. 92 S&F 110mm PVC (SWR) bends any radius provided with access door fixed to pipe , complete all as specified. 93 M&L for applying two coats of Dr Fixit Roofseal (Classic) over plaster/ roof /concrete surfaces including one coat of primer as per manufactureres instructions, complete all as specified & directed. 94 Dismantling boarding, any description, fixed in any position with nails, complete all as specified. 95 Supply and fix false ceiling with powder coated exposed GI grip suspension system (E-grip T-2430 of equivalent load carrying capacity with mid span deffection not exceeding 1/360 span with hanger spacing of 1200mm c/c) consisting of main runner 3600mm long, cross tee 1200mm/600mm long wall angle. The main runners to be placed @ 1200mm, the cross tee 1200mm will be inserted in the pre cut slots of main runner at a regular interval of 600mm from a modular grid of 1200mm X 600mm. Additional cross less of 600mm shall be placed perpendicular to the cross tee 1200mm long to finally from a grip of 600mm X 600mm. Grip of modular size 600mm X 600mm shall be supported by 3-4mm dia GI rod from purlins/soffit and fixed complete all as specified and as directed. 96 S&F for ceiling boards made of mineral fiber tiles of size600x600x15mm , fixed in snap grid false ceiling frame work of approved colour, type complete fixed in position all as specified and directed. Make : Armstrong Optra RH95/ FG Classic. complete all as specified. 97 S&F Solid PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC fillets, complete all as specified. 98 S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame complete all as specified. 99 Removal of existing concrete including loose/weak concrete from the concrete structure i.e. beams/ columns/ deckslab etc upto beyond corroded steel reinforcements to a depth of minimum 10mm behind the reinforcement by chipping/hacking with chisel and hammer or by mechanical means like chisel hammer, pneumatic chippersincluding high pressure water jetting and removal of debris. Concrete around the corroded reinforcement shall be removed properly. Theedges of the repair locations of concrete should be saw cut to depth of at least 10mm to avoid featheredging and to provide a square edge complete all as specified and directed by Engr-in- Charge. Note :- The contractor Quoted rate should includes necessary scaffolding and form work both for new work as well as for protection of existing structure during rehabilitation. 100 Preparation of surface and removal of rust in the loosely bonded concrete of the RCC deckslab, beam / girder and piles shall be chipped out using the mechanical cutter exposing the bars and applying Rust Remover using small brush and allow to react it for 16-24 hrs. Before applying protective coating,the surface should be wire brushed and thoroughly cleaned for dust with dry cloth complete all as per manufacturer instructionsand directed by Engr- in- Charge. Note :- The contractor Quoted rate should includes necessary scaffolding and form work both for new work as well as for protection of existing structure during rehabilitation. 101 M&L for applying two coats of Anti-Corrosive Primer two component (epoxy anticorrosive zinc rich coating) on reinforcement steel surfaces uniformely. Coating shall be applied by the brush to the exposed and cleaned rebars with an interval of 45 minutes to 1 hour @ 40microns DFT / coat and allowed to completely dry for 24 hours complete all as per manufacturer instructions and directed by Engr- in-Charge. Note :- The contractor Quoted rate should includes necessary scaffolding and form work both for new work as well as for protection of existing structure during rehabilitation. 102 M&L preparation of concrete surfaces by removing loose concrete, dust, dirt etc, cleaning the surface properly and applying one liberal coat of epoxy bonding agent ( two component agent) by brush application complete all as per manufacturer instruction and directed. Note :- The contractor Quoted rate should includes necessary scaffolding and form work both for new work as well as for protection of existing structure during rehabilitation. 103 M&L for 50mm thick polymer modified mortar ( average thickness) modified single component, alkaline resistant fibre reinforced, thixotropic, cementitious patch repair mortar on conrete structure. Applying the mortar arround the reinforcement and finishing to bring it in line with existing concrete surface complete all as per manufacturer instructions and directed by the Engr-in- Charge. Note :- The contractor Quoted rate should includes necessary scaffolding and form work both for new work as well as for protection of existing structure during rehabilitation. 104 M&L for Preparation of new plastered surfaces of wall and apply two coats ofAcrylic emulsion exterior paint of required shade :(Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm), complete all as specified. 105 M&L for preparation of new plastered or unplastered surfaces of ceiling and apply two coats of distemper oil emulsion over a coat of 1mm thick wall care putty, completeall as specified. 106 M&L for preparation of old surface of walls and applying 1 coats of Oil Bound distemper on walls, complete all as specified. 107 M&L for preparation of old wall surfaces and Fiinishing walls with Acrylic Smooth exterior paint of required shade : New work (Two coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)and upto ht of 15m from GL , complete all as specified. 108 M&L for preparation of old plastered or unplastered surfaces of ceiling and apply one coats of distemper oil emulsion, completeall as specified. 109 M&L Granite (of any type) work (table rubbed and polished) 20mm thickin steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite., and nosing /rounding to edges of stone slabs one edge,all as specified and directed . 110 Dismentling floor hearth or wall tilling including cement mortar bedding ( but not backing) all as specified. 111 M&L for non skid ceramic coloured tiles Ist quality7 to 8mm thick, (square/ rectangular), area of each tile exceeding 0.11 sqm, but not exceeding 0.18 sqm as in floors etc. set and jointedin neatcementslurry and pointed in white or coloured cement to match the shade of tiles, laid over and including15mm thick screed bed or bedding layer in cement mortar1:6, complete all as specified and as directed by the Engineer-in-Charge.Note: Colour and shade of tiles shall be approved by Engr-In-Chargeand contractor shall not have any claim whatsoever on this account. 112 M&L for Glazed ceramic tiles, coloured, of size350mm x 250mm/450 mm x 300mm, thickness not less than 7mm as in vertical surfaces such as skirting/dado etc, set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match the shade of tile, fixed over and including 10mm thick rendering (bedding layer) on brick/concrete surface in cement mortor 1:4, complete all as specified and as directed by the Engineer-in-Charge.Note: Colour and shade of tiles shall be approved by Engr-In-Chargeand contractor shall not have any claim whatsoever on this account. 113 Dismantling water tanks of exc250 ltr but n exc 500 ltr. ofany description from roof slab of building up to up to any height of building. Completeall as specified and as directed by Engineer-In-Charge 114 Dismantling water tanks of exc 500 ltr but n exc 1000 ltr. ofany description from roof slab of building up to any height of building completeall as specified and as directed by Engineer-In-Charge 115 Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) three layers hoisted andfixed in position complete andall as specified and as directed by Engineer-in-Charge 116 Supply and fixing 1000 Litre capacity Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) three layers hoisted andfixed in position complete andall as specified and as directed by Engineer-in-Charge. 117 S & Fin repairs Ball brass valves, (20 mm) high pressure, with ploythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete andall as specified and as directed by Engineer-in-Charge. 118 S& F as in repairs Gun metal gate vlaves 20mm bore of dia with iron wheel head, screwed both ends for pipe, complete all as specified. 119 S&F PVC Cover for HDPE water storage tanks of capacity 500 /1000 litres including PVC hinges and PVC locking arrangment ,complete all as specified. 120 S&F as in repairs Vitreous China wash down water closet pan (pedestal pattern), including Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as specified. 121 S&F PVC valveless, syphonic action type flushing cistern, 10 litres capacity, plunger type, low level, white with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 90cm long, fixed in repairs, complete all as specified and as directed by the Engineer-in-Charge. 122 S & F in repairs viterous china wash hand basin of size 550 x 400 mm, whiteflat back excluding taps, waste, chain and plug and porcelean stopper but including bracketsincluding CP waste fitting and PVC Wastepipe complete all as specified and as directed. 123 S&F Vitreous Chinaware squatting pan, orissa pattern size 580mm x 440mm with integral foot rests, white, with cast iron ‘P’ or ‘S’ trap, front or back inlet, including provision of lime concrete, making connections to trap and to flush pipe etc. and making good to floors, fixed in repairs,complete all as specified and directed by the Engineer-in-Charge. 124 S&F in repairs bib tapsin 15mmbore of pipe, copper alloy,chromium plated, with crutch or butter fly handle screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed. 125 S&F as in repairs 15mm bore dia fancy type Bib taps, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixedcomplete all as specified. 126 S&F as in repairs 15mm bore dia Stop valves/angle cock, CP cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified. 127 S&F as in repairs 15mm bore dia pillar tapcast copper alloy, chromium plated ,screwed down high pressure,with long shanks and flynuts, screwed for irom pipe, complete all as specified. 128 S&F in repairs wall mixer 2 in 1 system with provision for overhead shower with 115mm long bend pipe on upper side, connecting legs & wall flanges, chromium plated, complete all as specified. 129 S&F Mirror with plastic cabinet of size 330mmx430mm single door as per approved Make:- Prayag cat No 551 /Neelkamal / shakti 130 S&F in repairs aluminium anodised chromium plated tubular towel rail 20mm dia & 60cm long between flanges of Make: Prayag . complete all as specified and as directed by Engineer-In-Charge. 131 S&F as in repairs health faucet (ABS Body mild steel chromium plated suitable for 15mm dia pipe with 1.25 meter long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. 132 S&F as in repairs Chromium plated shower roses 125mm size with or without swivel joints, any size, including fixing to steel pipe or union, complete all as specified. 133 S/F in repairs glass corner shelf 300 mm with Abs brackets )300x 600 with heavy wall brackets and ss railing at corners fixed with CP screws etc completed and as directedof make Prayag having cat No.BEA 46 134 S&F as in repairs 32mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, complete all as specified. 135 S&F as in repairs 40mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, complete all as specified. 136 S& F in repair 32 mmcorrugated Waste Couplling, PTMT (half or full threadminimum weight 45 gmsfor Sink/urinals etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed. completeall as specified and as directed. 137 S&FLow density polyethylene pipes (LDPE) of pressure rating 6 kg/ cm2 of40 mm dia borefor wash hand basin/ sinks etc and fixed as in repairs, complete all as specified and directed. 138 S&Fin RepairPVC connection 15mm size with PTMT nuts, of length 450mm Complete all as specified and as directed. 139 Taking up or down 15mm bore steel tubing and connections,complete all as specified. 140 Taking up or down 20mm bore steel tubing and connections,complete all as specified. 141 S&F 15mm bore steel water tubes, medium grade, galvanised, with all fitting and fixed complete to walls ( concealed) and ceilings or laid in floors, complete all as specified. 142 S&F 20mm bore steel water tubes, medium grade, galvanised, with all fitting and fixed complete to walls (concealed) and ceilings or laid in floors , complete all as specified. 143 S & F in repairsGratingof 125 mm dia of stainless steel with or without waste hole, complete all as specified and as directed. 144 M&L for preparation of old treated plastered or un-plastered surfaces of walland applying two coat of oil bound distember etc complete all as specified and as directed by Engineer-in- Charge 145 M&L for preparation of patches of damageoldplasteredsurfaces of ceiling with 2mm wall care putty etc complete all as specified. 146 M&L for preparation of patches of damageoldplasteredsurfaces of wall with 2mm wall care putty etc complete all as specified . 147 M & L for preparation of old treated wood surfaces of any description over 10 cm width & girth not otherwise described and applying one coat of synthetic enamel paintcomplete all as specified and directed. 148 M&L for preparation of oldsteel Surfaces and paint of any description, over 10cm in width or girth,not otherwise described complete all as specified and directed 149 M&L Coloured Glazed Ceramic tiles 300 x 200 and6-7mm thick on vertical surfaces such as skirting, dados and risers to steps etc including 10mm thick backing coat in CM 1:4 complete all as specified and directed Note : Tiling work is carried out in patches. 150 M&L non skid ceramic tiles(Coloured) 7 to 8mm thick (square/rectangular) area of each tile exc 0.06sqm but n.exc 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including screed bed 15mm thick in CM 1:6 complete all as specified and directed Note : Tiling work is carried out in patches. 151 S&F as in repairs 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified 152 M & L For cleaning of OH PVC Service Tank internally by bailing out of water/sludge from bottom of sump, removing all scale, dirt, alges and other growths from entire surfaces of tank and from mouths of Circulating pipes by rubbing with wire brushes and by high pressure cleaning method with roatary sets with approved detergents and sucking all dirty water by avaccum cleaners, disinfecting the tank with approved chemical/bleaching powder for making the surfaces bacteria free and cleaning with fresh water, all as direced by Engg-in-charge.(a) Overhead Pvc water tank upto 500 Liters of capacity NOTE- cleaning of OH PVC service tanks are safely to be handled Damage and bracking of tanks are on Contractors OWN risk. 153 -ditto as item No 152 but exc 500ltr and n.exc 1000 Itrs capacity 154 M&L for 50mm thick cement concrete 1:2:4 type B-1 using 20mm graded aggregate as in floor finishing the surface even and smooth without using extra cement complete all as specified. 155 S&F 100mm size stainless steel Butt hinges 1.75 mm thickness, with matt finish, complete all as specified 156 S&F for ordinary sheet glass 4mm thick and glazing in aluminium frame work, complete all as specified 157 Resecuring or easing & adjusting with taking down shutters of any description exc 1 sqm but n.exc 2 sqm, complete all as specified & directed 158 S&F 30mm width of flaps continuous (piano) hinges mild steel, bright finish orelectrogalvanised, complete all as specified & directed 159 S&F as in repairs 125mm size Hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified 160 M&L for rendering 10mm thick CM 1:3 on fair faces of concrete surface and finised surfaces even and smooth without using extra cement completeall as specified and directed. 161 S&F anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as directed by Engr-In-Charge.
