Tender For Atal Gyan Kendra Library Construction Work In Village Ramasar. - Excavation of soil up to 1.5 m depth in foundation, trench, drain, compaction of the bottom, pouring water, grooming the sides, taking out the excavated soil, filling the empty spaces with soil again after filling the foundation and disposal of the remaining soil up to a distance of 50 meters.2 In hard, clayey, gravelly soil, 40 mm nominal size stone aggregate (crusher broken)/brick soil should be put in cement concrete foundation or floor in the ratio of 1 cement: 4 sand: 8 aggregate in cement-sand mixture and compaction, including leveling. If 40 mm crusher broken stone aggregate is used along with stone aggregate (crusher broken), the same quantity will be payable but there will be a 30% reduction in the rate of aggregate. 3 Foundation and plinth first class brickwork in cement-gravel 1:6 or 1:8 mortar, including side crack filling and grouting. Cement mortar 1:64 Pouring and supply of reinforced cement concrete of 1:2:4/1:1.5:3 mix, including burying, grouting and leveling of roof slabs, eaves, beams, lintels, etc., including scaffolding, but cost of steel and shuttering separately. Ratio 1:1.5:35 Foundation and plinth first class brickwork in cement-gravel 1:6 or 1:8 mortar, including side crack filling and grouting. Cement mortar 1:6 Additional amount for masonry work in superstructure up to a height of 4.5 meters from plinth level.6 Cutting, bending, fitting and fastening of iron for RCC work with supply. 7. Centering (shuttering) for RCC roofs, slabs, balconies, lintels, etc. up to 4.5 meters in height and removal as per specifications. Shuttering Steel8. Cement concrete bars (1 part cement, 3 parts gravel, 6 parts 12 mm measured aggregate) of 90 mm average thickness, including tamping and compaction. (i) The bars should be laid in such a way that a slope of 1:50 is achieved in the desired direction, with 6 mm diameter bars placed at 25 cm centers in both directions, with concrete in the center of the grid, as per specifications. (ii) In case of trenching less than the specified thickness, a deduction of 10 percent of the total cost will be made for every inch of thickness less than the prescribed thickness.9. S & F Glazed tiles on roof10. Providing and fixing 12.5 mm thick tapered edge gypsum board conforming to IS 2095- Part I at all height false ceiling including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanized in accordance with zinc coating of grade 350 as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm center to center one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm center to center to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of10.5mm at 450mm center to center shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long(PWD BSR -2022)11 Cement plaster on the wall by mixing cement-gravel in 1:6 ratio including scraping the joints and regular leveling for 14 days. 20 mm12 Providing and applying white cement basedputty overplasteredsurfaceto preparethesurfaceevenandsmoothcomplete(PWD-2022-Less - 10%)13 Applying one coat of cement primer of approved brand and manufacture on wall surface including all scaffolding: (PWD-2022-Less - 10%)14 Wall painting with plastic emulsion paint of required shade including all scaffolding.New work (Two or more coat includingbasecoatofwaterproofing cement paint) -PWD BSR-2022 Item no. 12.40.115 Supply and installation of stone door and window frames using 1:4 cement mortar. Analysis for a double-layered 125 x 75 mm door frame of 8 meters.16 Supply and installation of a factory-made solid core, single-pane 30 mm door with commercial ply on both sides, with beading bolts, two latches, and two handles, using three enamelled hinges. Analysis for a 1 x 2 square meter door.17 S & F Section window18 Supply and installation of 14 mesh, 24 gauge iron window mesh for an iron window, using 20 x 3 mm beading and screwing. Analysis 1.2 X For a 0.60 meter window, for 0.72 square meters19 Iron work in grills/gates, etc., including cutting, mounting, and fitting flat corners, T-pieces, and channels.20 S & F Aluminum door21 Applying enamel paint in three layers to give an even shade. Creating an even surface on new/old work.22 S & F Channel door23 Earthwork in filling, digging a quarry on the roadside, lifting 1.5 meters of soil and transporting it to 50 meters, breaking lumps, laying them in 25 cm layers, tamping, leveling, and cambering. Ordinary soil24 Carriage of earth-lead two kilometers25 Laying 40 mm nominal size stone aggregate (crusher broken)/bricks in cement concrete foundation Aggregate Cement Sand Masala 1 Cement : 6 Sand :12 aggregate ratio, mixing, pouring, and tamping, including compaction. (As per IS Code 7272 and 10067) If hand-broken gravel is used instead of 40 mm crusher-broken stone aggregate, the same quantity will be payable, but the rate of aggregate will be reduced by 30%.26 Supply of white glazed china clay tiles and plastering with cement slurry and white cement in the joints (price of plaster not included). Glazed tiles size 30 x 45 cm27 Furniture and others28 Computer, Scanner, Printer, Inverter, etc.29 Water cooler, R.O., Electric fittings + Water fittings, etc.30 Planning board & Contengency charges
