Tender For Special Repair To Bldg No Knd-01 And Knd-86 At Jutogh Cantt Under Ge (I) Jutogh; 1 Taking down Cement plaster on brick or stone walls incl raking out joints hacking for key & scrubbing down with water etc., complete all as specified and directed. 2 M&L for 15mm thick cement plaster (1:6) on other than fair faces of brick work or concrete Surface finished even and smooth without using extra cement, complete all as specified and directed. 3 M&L for preparation of newly plastered surfaces of wall and applying two coats of distemper oil emulsion over a coat of alkali resistant priming paint and one coat of wall putty on wall surfaces including preparation of surfaces, complete all as specified and directed. 4 Complete removal of existing treatment on wall (any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped with wall care putty not less than 3mm thick in two layers and preparation of surfaces for further treatment andapplying two coats of oil bound distemper (white/ Approved shade) complete all as specified and directed. 5 M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:4), using water proofing compound complete all as specified and directed.Note: WPC shall be measured and paid separately. 6 Supply only water proofing compound, complete all as specified and directed. 7 M&L for complete removal of existing treatment (incl weed growth surrounding sewage pipe and water tank portion) of plastered or unplastered old decorated surface walls by brooming down and applying two coat of weather proof anti fungal exterior emulsion painton external surfaces includingtwo coats (not less than 3mm thick) exterior wall care putty (true care wall putty) for a smooth wall finish at any height of building/ tower incl necessary scaffoldings and T&P, complete all as specified and directed. 8 Demolitionof brick/ stone masonry work including allquoins arches pillars etc built in cement mortar/Lime Mortar, complete all as specified and directed. 9 M&L for half brick work with sub class B brick in cement mortar 1:4, straight or curved on planexc 6 m mean radius, complete all as specified and directed. 10 M&L for walling of random rubble, uncoursed well bonded, built in CM(1:6) as in parapet, steps complete all as specified and directed. 11 M&L for brick work in cement mortar (1:6) using sub class B bricks straight or curved on plan exc 6.0 m mean radius, complete all as specified and directed. 12 Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended work, complete all as specified and directed. 13 M&L for Formwork to soffits of suspended slabs, such as roof slabs, floor slabs landing and similar work not exceeding 200mm thick (Horizontal & sloping) fair finished surfaces, complete all as specified and directed. 14 M&L for RCC 1,1.5,3, Type A-1, Nominal Mix, type using 20mm graded stone aggregate in slab supported on walls, beams and columns in floors,roofs,landings,balconiies,deck slabs and in shelves and the like complete all as specified and directed. Note: Form work and reinforcement measured and paid separately. 15 M&L for mild steel 10 mm dia and over TMT bar cut to length, bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. 16 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), rubbish off the premises complete all as specified and directed. 17 M&L for 25mm thick PCC 1:2:4, Type B-1, using 12.5mm graded crushed stone aggregate as in floor finished rough to receive floor finishes etc., complete all as specified and directed. 18 M&L for non skid coloured ceramic tiles 400 x 400 x 7 to 8 mm set & jointed with neat cement slurry & pointed in white/coloured cement to match the tiles over 15mm thick screed bed incement mortar 1:4, complete all as specified and directed. 19 M&L for glazed ceramic high glossy colouredtiles300x200x7/ 450x350x7/300x600x7 to 8 mm thick onvertical surface such as skirting , dado etc. over 10 mm thick backing coat plaster in CM 1:4 complete all as specified and directed. 20 M&L for glazed ceramic tiles/ joint free exterior stone kraftin vertical surfaces(Brick/stone surface)of size 350x250x7mm/ 450x300-350x7/300x600x8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick backing coat in cement mortar 1:4, complete all as specified and directed. 21 M&L for vitrified ceramic tiles 10 mm thick of light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to matchlaid over and including 20mmthick screed bed with cement mortar 1:6, complete all as specified and directed. 22 M&L for vitrified ceramic tiles 10 mm thick of light shade (square/ rectangular)as in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to matchlaid over and including 20mmthick screed bed with cement mortar 1:6, complete all as specified and directed. 23 Demolition of stone slabs and tiles (chequered tiles) of any description or thickness in floors aprons etc laid bedded and pointed in any mortar, complete all as specified and directed. 24 M&L for machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed. 25 M&L for screed bed or bedding layer of mortar 20mm thick in cement mortar 1:4 for laying floor finishes to receiving the kota stone, complete all as specified and directed. 26 M&L for coloured chequred cement concrete tiles (30cm x 30cm x 25mm thick) in grey cement and with pigment in floors etc , set and jointedin neat cement slurry, over and including 20mm thick screed bed in cement mortar 1:6, complete all as specified and directed. 27 M&L for granite (of any type)20 mm thick one side machine polished in steps (including nosing and treading), jambs, pillars, window Cills, and top of kitchen platform and top of counter top wash basin etcset and jointed in neat cement slurry and pointed with coloured cement to match including 20mm thick screed bed in CM 1:4, complete all as specified and directed. 28 M&L for granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) including laid over 12 mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed. 29 Rounding to edgesof stone (of any description) slabs one edge, such as in steps, cooking platform, and other similar situations including rubbing and polishing (mirror finish), complete all as specified and directed. 30 M&L for 75mm thick PCC 1:3:6, Type C-2, using 40mm graded crushed stone aggregate as in plinth protection finished even & smooth complete w/o using extra cement complete all as specified and directed. 31 M&L for PCC 1:3:6, type C-2, using 40mm graded crushed stone aggregate as in surface channel/ drains incl fair finishes &necessary formwork complete all as specified and directed. 32 M&L for 50mm thick PCC 1:3:6, type C-1, using 20mm graded crushed stone aggregate as in plinth protection finished fair and even without using extra cement, complete all as specified and directed.Note:- The plinth protection shall be laid in panels and length of the each panel shall not be more than 2.00 mtr all as directed. 6mm joints filled with 85/25 grade bitumen and sand (1:3 ratio) shall be provided. No deduction for joints shall be made while making payment against the above item. 33 Taking down chowkats or frames with shutters (with out taking off shutters from the frame) not exceeding 1.50 Sqm each, complete all as specified and directed. 34 Taking down chowkhats or frames with shutters without taking off shutters from the frame exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed. 35 S&F pressed steel frames of size 125 x 60 mm for doors with one or more rebates including supply & fixing lugs, 125 mm size hinges, lock strike plate, etc., complete all as specified and directed. 36 S&F pressed steel frames of size 105 x 60 mm for doors with one or more rebates including supply & fixing lugs,125 mm size MS hinges, lock strike plate, etc., complete all as specified and directed. 37 S&F band, straps, supports or stays for rain water, ventilating pipes including bolts, if required, hooks (stay), heavy, for large gates, hook and pintle hinges large hasps and staples, chain hand made sliding bolts clamps hold fasts wall ties, hooks for hanging fans plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two ways and three way straps, plate washers and similar small articles conforming to fe-290 gde E-165, complete all as specified and directed. 38 M&L for PCC 1:3:6, type C-1, using 20 mm graded mechanically crushed stone aggregate as in filling pressed steel frame/ hold fast blocks etc., complete all as specified and directed. 39 S&F 35mm thick flush shutters, solid core construction, with partical board core and plywood face panels, commercial type on both sides with 2nd class hardwood lipping/ frame, complete all as specified and directed. 40 S&F 35 mm thick factory made glazed & skelton shutter of 2nd class Hardwood open rebated & prepared to receive glass or gauze etc. without sash bar open rebated with edges of framing plain, chamfered or rounded, fitted with cut & mitered beads for securing glass or gauge etc. size of stiles rails etc. as specified in sec 8 clause 8.24 (a) of SSR Part-I (2010), complete all as specified and directed. 41 S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed.Note: 1) M.S. hold fast/ lugs or SS dash fasteners shall be paidseparately. 2) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 42 S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed.Note: Stainless steel butt hinges and necessary S S screws shall be paid separately. 43 S&F Aluminium anodised powder coated (powder coating color/shade as approved by GE) sliding type three track window/ventilator with shutter and frame including aluminium grill and mosquito proofing net and 5 mm thick tinted glass , size of frame 98.50 x 31.75 x 1.3mm thick for top and sides, 98.50 x 31.75 x 1.2mm thick, bottom and shutter frame 38 x 18 x 1.5mm thick, Aluminium grill 6 mm dia design No. DG-102 make DEDO grill or design No. A-103 make aluminium grill fixed to 50 x 20 x 1.5mm thick including necessary handles, tower bolts etc. complete all as specified and directed. 44 S&F anodised powder coated (powder coating color/shade as approved by GE)aluminium frame/shutters for doors, windows, ventilators of powder coating minimum thickness of powder coating 50 micron with one or more rebates including joining cleat for fixingand cleat s for receiving glass/wire mesh etc. complete all as specified and directed. 45 S&F powder quoted aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. with a provision for exhaust fan, complete all as specified and directed. 46 S&F aluminium anodised grill diamond shape 100 mm x 100 mm aperture of 6 mm dia round bars including necessary joining cleats, clips anodised aluminium snap beading screws complete all as specified and directed. 47 S&F 4mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.50 sqm in each pane complete all as specified and directed. 48 S&F figured glass 4mm thick pin head type ordinary quality, ground or obscured or frosted, on one side with oil putty in square n exc 0.5 sq. m in each pane, complete all as specified and directed. 49 S&FGalvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of apertures 1.18 mm fitted with tinned tacks or galvanised wire staples, complete all as specified and directed. 50 S&F in repair Galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of apertures 1.18 mm fitted with tinned tacks or galvanised wire staples, complete all as specified and directed. 51 Hacking Out Old Broken Glass (any thickness, size, quality or description) from Wooden Frames, Glazed with Putty or fixed with Beads, of any height including necessary scaffolding and T&P required to complete the work, complete all as specified and directed. 52 S & F sheet glass ordinary quality 4 mm thick glazing in square/ rectangle n.exc 0.50 sqm each pan with oil putty or aluminium beads fixed to steel and wooden of any height including necessary scaffolding and T&P required to complete the work, complete all as specified and directed. 53 All as per Srl Item No 52.00 above but for figured glass, complete all as specified and directed. 54 S&F Butt hinges 100mm long, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, complete all as specified and directed. 55 S&F Aluminium tower bolt of extruded section, 200mm length of bolt and fixed with screws, complete all as specified and directed. 56 S&F 300mm long aluminium alloy, anodized, sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy and fixed with screws, complete all as specified and directed. 57 S&F 250mm long aluminium alloy, anodized, sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy and fixed withscrews, complete all as specified and directed. 58 S&F 300 mm MS ordinary rat tail rod pattern springs incl roller and roller plate fixed to wooden chowkhats or welded to angle iron door frames, complete all as specified and directed. 59 S&F floor door stopper aluminium body and tongue, anodised overall length of cover plate of size 75 mm long with hard drawn steel spring, complete all as specified and directed. 60 M&L for preparation of new wooden surface of any description not otherwise described over 10cm width or girth and applyingtwo coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed. 61 M&L for painting to steel surfaces of any description not other wise described over 10cm width or girth with two coats of synthetic enamel paint incl preparation of new surfaces complete all as specified and directed. 62 M&L for preparing old painted surfaces of wood and wood-based materials of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of white/ approved shade, complete all as specified and directed. 63 M&L for preparing old surface ofsteel & iron surfaces of any description over 10 cm in width or girth , and applying one coat of white/ approved colour/ shadesynthetic enamel paint, complete all as specified and directed. 64 S&F in repair stainlesssteel tube of 25 mm dia chromium plated min. 1.0 mm wall thickness as in curtain rod complete incl S&F 02 Nos stainless steel brackets and finials fancy type, stops fixed with ss screws etc., complete all as specified and directed. 65 Taking up or down steel tubing and connections of 15mm bore in pipe, including cleaning for re-fixing or removal from site, complete all as specified and directed. 66 Taking up or down steel tubing and connections of 20mm bore in pipe, including cleaning for re-fixing or removal from site, complete all as specified and directed. 67 M&L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc., and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth, complete all as specified and directed. 68 S&F 15mm dia GI tubing medium grade incl fittings, cutting threading and fixing to walls or fixing in concealed walls or in floors etc., and making good the surfaces matching to existing surfaces of walls/ floor, complete all as specified and directed. 69 S&F in repair vitreous china wash hand basin white flat back of size 550 x 440mm including CI brackets ,chromium plated waste coupling 32mm waste pipe etc., (incl all waste fittings), complete all as specified and directed. 70 S&F Brass CP WHB Mixer valve for mixing hot and cold water screwed down for 15mm dia iron pipe, complete all as specified and directed. 71 S&F Brass CP kitchen sink Mixer valve for mixing hot and cold water screwed down for 15mm dia iron pipe, complete all as specified and directed. 72 S&F in repair 15 mm fancy type chromium plated fancy type bib tap brass long body with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union complete all as specified and directed. 73 S&Fin repair PTMT grating openable 100mm sqmm size with/without hole including fixing with white cement complete all as specified and directed. 74 S&F in repair 15mm bore, fancy type, chromium plated Stop valves, cast copper alloy, screwed down,high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and directed. 75 S&F in stainless steel plate rack (utensil rack for kitchen of size 750 x 600 x 250mm and min 0.80 to 1.00 mm thick fixed with stainless steel screw and rawl plug, complete all as specified and directed. 76 S&F in repair sheet glass shelf assembly consisting of 5.5 mm th sheet glass shelf 12 cm wide with chromium plated guard and railing 60 cm long, complete all as specified and directed. 77 S&F in repair soap dish any type, fixed to plugs with chromium plated brass screws, complete all as specified and directed. 78 S&F in repair chromium plated, towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and directed. 79 S&F for PVC connections 15mm size with PTMT nuts of length 450mm, complete all as specified and directed. 80 S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste pipe incl bedding in cement mortar to dwarf wall ot cantilever brackets and connecting union to pipe overall size 915x460mm, bowl size 410x 330x160mm incl all fittings ie CP waste coupling, waste pipe, complete all as specified and directed. 81 S&F in 600x450mm size beveled edge looking mirror of selected quality glass mounted on 12mm thick marine plywood with powder coated aluminium frame around and fixed with wooden plugs, CP screws, cup and washers, complete all as specified and directed. 82 Taking down of Eaves gutter/rain water pipe( AC/ PVC/CI, rain water pipe/ SWG pipe line of any size or pattern), incl all fittings, complete all as specified and directed. 83 S&F in repair 110mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and directed. 84 S&F in repair 75mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and directed. 85 S&F PVC (SWR) floor trap 75mm, plain with grating including jointing with solvent cement, complete all as specified and directed. 86 S & F in PVC (SWR) junction single, (Single T 110mm), equal or unequal with access doorcomplete all as specified and directed. 87 S & F in PVC (SWR) junction single, (Single T 75mm), equal or unequal with access door, complete all as specified and directed. 88 S&Fin repair PVC (SWR)bends, for 110mm bore pipes, with access doors, complete all as specified and directed. 89 S&Fin repair PVC (SWR)bends, for 75mm bore pipes, with access doors, complete all as specified and directed. 90 M&L for salt-glazed stone ware gully traps, 150x 150 square or round mouthed, type p setting and jointing to drains with CM 1:1 complete all as specified and directed. 91 Dismantling of water tanks exc 500 ltrs capacity but not exc 1000 ltr capacity and removal at site, complete all as specified and directed. 92 S&F 1000 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) double layeredhoisted and fixed in position, complete all as specified and directed.. 93 Refixing ofRotational moulded polyethylene water storage tanks of 1000 ltr or less capacity (cylindrical vertical with closed top) three layer hoisted and fixed in position all as specified and directed in SSR Part-I, complete all as specified and directed. 94 S&F Ball valve of brass, 20mm bore, high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and directed. 95 S&F CI Gate valve, 20mm bore, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union complete all as specified and directed. 96 S&F CI Gate valve, 15mm bore, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or unioncomplete all as specified and directed. 97 S&F 110mm bore PVC (SWR) pipe single socket, in any length with rubber ring joint, laid in trenches or in floor, complete all as specified and directed. 98 S&F 75mm bore PVC (SWR) pipe single socket, in any length with rubber ring joint, laid in trenches or in floor, complete all as specified and directed. 99 S&F in repair PVC bend (any radius)of 110mm bore, complete all as specified and directed. 100 S&F in repair PVC bend (any radius)of75 mm bore, complete all as specified and directed. 101 S&F PVC (SWR) vent cowl 110 mm dia, complete all as specified and directed. 102 M&L forPCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in cover slab placed in position over manholes etc. including use and waste of necessary formwork complete all as specified and directed.Note :- Reinforcement and handles shall be measured and paid separately. 103 M&L for TMT bars 6 to 8mm dia and over cut to length bent to shape required and binding with MS wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed. 104 M&L for PCC 1:2:4, type B-1, using 20mm graded mechanically crushed stone aggregate as in padding to roof to maintain the required slope and finished the surface even and smooth without using extra cement, complete all as specified and directed. 105 Demolition of cement concreteof any description and in any position, complete all as specified and directed. 106 M&L for PCC 1:5:10, type E-2, using 40mm graded crushed stone aggregate as in foundations, filling and mass-concrete as in sunken floor etc., complete all as specified and directed. 107 M&L for providing kitchen cabinet in required sizes at site made out of 18 mm thick one decorative lamination sheet consisting of care as 22 mm thick WPC & provision of shatters made out of 22mm thick one side decorative laminated sheet all required brackets 5.5 screws etc. the panels shall be fabricated using adhesive and screws where even required . All the edges shall be covered with 2mm thick edge bounding tape or 90 degree edge bent finish as per make, complete all as specified and directed. 108 S&F magnetic catcher fixed with nut screw and washer complete all as specified and directed. 109 S&F telescopic drawer sides channel- Zinkplated complete all as specified and directed. 110 S&F stainless steel soft close crank hinges suitable size and shape as required, complete all as specified and directed. 111 S&F framed work such as grills,cooler stand ,grating, tank staging etc., with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work or water tanks and similar work conforming to Fe 410-0 or Fe 310-0, complete all as specified and directed. 112 Dismantling wrought iron or mild steel work of any description not otherwise provided, complete all as specified and directed. 113 S&F roof trusses (framed), trussed, purlins, rafter, sun shades, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., Fe-410-W (Gde-E-250), quality-B, complete all as specified and directed. 114 Dismantling plain or corrugated steel sheeting any gauge thickness incl Nainital pattern as in roof covering, complete all as specified and directed. 115 S&F pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ ceiling/ cladding to wall, fixed with self tapping screws, complete all as specified and directed. 116 S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges, flashing, facia (approved design), eaves board valley gutter of any shape/ any dia etc., cut to designed shape (Jhhallar) at site fixed all as per manufactures instructions and fixed with self thread making steel screws of length not less than 50mm, at site with suitable arrangement as required incl any height and with scaffolding and safety T&P, complete all as specified and directed. 117 Dismantling wall, ceiling and floor boards (fiber, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets, GI grid/wooden frame work, complete all as specified and directed. 118 M&L for providing and fixing gypsum boardtiles PVC laminated (0.7mm texturedrigid poly vinyl film) of size 600 X 600mm, 9-12 mm thick in ceiling fixed with screw a timber/ GI/ Aluminium frame work with screws in ceiling flat or sloping, complete all as specified and directed. 119 GI frame powder coated work of size 605 x 605 mm for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm center to center/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx. 900 mm center to center with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm center to center, complete all as specified and directed. 120 Hangers 6 mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long, complete all as specified and directed. 121 S&F GI Clip-in false ceiling tiles of with beveled edges of with GI sheet (600mmx600mm) is manufactured out of 0.50mm galvanized steel of 100 gsm/ sqmtr sheet having powder coated with 60 microns polyester paint on front side. These tiles shall have beveled edges. Two sides of each tiles are raised and piped and stopped to ensure positive engagement into the spring clip-in profile, yet allow for demounting of individual tiles. The rigid suspension system consists of rows of 0.5mm galvanized steel clip-in profiles of size 24mmx34mm of 0.5mm thick and installed at 600mm c/c spacing to support the tiles, clip-in profiles are suspended with hold on clamps. Suspension angles or 4mm G.I Wire are suspended from the roof structure. The tiles are held in place by pressure clips. In the flexible system the hanger and suspension clip replace the suspension angle. GI Edge profile are of size 24mm x 24mm x 0.35mm thick with matching the color with tiles, complete all as specified and directed. 122 M&L for rendering 10mm thick on stone masonry/brick surfaces or surfaces other than fair face of brick work in CM 1:6, finishing surfaces even and smooth without using extra cement, complete all as specified and directed. 123 M&L for preparation of newly decorated plastered / unplastered surfaces of ceiling one coat of white wash on ceiling andAC plain building board surfaces as in ceiling, complete all as specified and directed. 124 M&L for preparation ofnewly plastered or unplastered or previously untreated surfaces of walls and applying two coats of exterior emulsion paint & over one coat of primer, complete all as specified and directed. 125 M&L for two coats of distemper oil emulsion on wall incl preparation of new surfaces over one coat of primer on wall surface incl 2mm thick wall care putty, complete all as specified and directed. 126 M&L for Non Skid ceramic tiles (coloured) 300x300x 7 to 8mm thick (square/rectangular) area of each tile exc. 0.06 sqm but n. exc. 0.11 sqm as in floors set and jointed in cement slurry and pointed in coloured cement including provision of screed bed 15mm thick in CM (1:6), complete all as specified and directed. 127 M&L for 1st quality, glazed ceramic coloured tiles 350x250x 7mm/ 450x350x7mm thick on vertical surface of walls with neat cement slurry @ 3.00 Kg/Sqm incl pointed in white cement with pigment to match the shade of tiles, over and incl screed bed 10mm thick 1:4, complete all as specified and directed. 128 M&L for non skid ceramic tiles 7-8mm thick coloured (square/ rectangular) each tiles exc 0.18 sqm but n exc 0.38 sqm in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed as in CM 1:6, complete all as specified and directed. 129 M&L for non skid ceramic tiles 7-8mm thick coloured (Square/rectangular)each tiles exceeding 0.18 sqm but n exc 0.38 sqmin vertical surface such as in skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick backing coat in cement mortar 1:4, complete all as specified and directed. 130 Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc. Laid, bedded and pointed in any mortar, complete all as specified and directed. 131 M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid & dado and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete over and including 15 mm thick screed bed or bedding with CM 1:6, etc., complete all as specified and directed.Note:- (i) The rate of kota stone shall be deemed to incl for full rounded off corner/ edges incl holes for pipe all cutting to make it square or rectangular.(ii) The rate shall also be deemed to incl for cutting and polishing machine and kota polishing to achieve the desired granite finish. 132 M&L for Green /Black marble flooring or on cooking platform 18 to 20mm thicklaid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thickcement screed bed in CM(1:6)(size of the slabs shall not be less than 100cmx60cm ), complete all as specified and directed.Note:- (i) The rate of granite stone shall be deemed to incl for full rounded off corner/ edges incl holes for pipe all cutting to make it square or rectangular.(ii) The rate shall also be deemed to incl for cutting and polishing machine and granite polishing to achieve the desired granite finish. 133 M&L for pre polished lacquer finish chequered cement concrete tiles 300 x 300 x 25mm thick, with grey cement and pigment set, jointedand pointed in neat cement slurry in floors over Screed bed or bedding layer of mortar as in 1:6 15 mm thick for laying floor finishes, complete all as specified and directed. 134 Dismantling of RCC shelf other than ground floors and similar suspended works, complete all as specified and directed. 135 M&L for RCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in shelves/ slabs and like with and incl use and waste of necessary form work, complete all as specified and directed. 136 M&L for PCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in copings, bed plates, fixing of hold fasts and other similar works and the like incl weathering, slightly rounded or chamfered angles and throating as directed incl use and waste of necessary form work, complete all as specified and directed. 137 Taking down shutters of any description exc 1sqm but n.exc 2sqm from chowkhat and removing to or from store, complete all as specified and directed. 138 S&F IInd class HW plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed. 139 S&F 30mm flush shutters, solid core construction, with block board core and plywood face panels, commercial types on both sidesincl teak wood beading alround the shutters, complete all as specified and directed. 140 S&F 2nd class hard wood 30mm thick made glazed and skeleton shutters factory made open rebated and prepared to receive glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass,etc, size of members of shutters as spfd in SSR Part-1, Section 8, clause 8.24 (a), complete all as specified and directed. 141 S&F in repair factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/ SS dash fasteners of required dia and length, and making it good to match with existing surface, complete all as specified and directed.Note: i) For WPC solid door/ window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable.ii) Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 142 S&F box type steel windowswith side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and directed. 143 S&F box type steel windowswith side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded, complete all as specified and directed. 144 S&F box type steel ventilators, with top hung shutter including hinges steel peg stay, complete all as specified and directed. 145 S&F 0.35mm thick colour coated liner profile sheet with high quality steel fixed with self tapping screw, complete all as specified and directed. 146 Dismantling of boarding of any description and in any position complete all as specified and directed. 147 S&F 18/19mm thick Block boards, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame,incl necessary beading wk where as required etc. complete all as specified and directed. 148 S&F 0.9mm thick decorative laminate(mica) type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturers instructions complete all as specified and directed. 149 S&F continuous piano hinges mild steel bright finish or electro galvanised with open flap width 30mm, fixed with screw complete all as specified and directed. 150 M&L for 75mm thick, PCC 1:3:6, type C-2, using 40mm graded crushed stone aggregate, laid in 1:20 slope as in plinth protection, coping, surface finished even and incl use and waste of necessary form work, complete all as specified and directed. 151 S&F Mild steel butt hinges medium weight, clod rolled, 100mm, ISI marked, complete all as specified and directed. 152 S&F aluminium fabricated type extruded handles of size 150mm complete all as specified and directed. 153 S&F aluminium fabricated type extruded handles of size 125mm complete all as specified and directed. 154 S&F in repair of 300mm mild steel ordinary rate tail rod pattern door spring incl roller and roller plate, complete all as specified and directed. 155 S&F in repair 20mm dia mild steel chromium plated curtain rails fixed with brackets, stops, rollers, etc., complete all as specified and directed. 156 S&F GI tubing medium gde with all fittings fixed to walls or laid in floors 20mm bore (concealed & open) complete all as specified and directed. 157 S&F in repair 15mm bib tap cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule, complete all as specified and directed. 158 S&F in repair 15mm bore CP fancy type (L-Type bend wall mixer ,sink mixer & WBH mixerfor mixing hot & cold water cast copper alloy with capstan handle, screwed down for iron pipe and fixed on wall , WHB, complete all as specified and directed. 159 S&F in repair stop valve/ Angle cock/ concealed fancy type cast copper alloy 15mm bore screwed down high pressure chromium plated concealed type, complete all as specified and directed. 160 S&F in repair stop valve cast copper alloy 20mm bore screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union fixed, complete all as specified and directed. 161 S&F stainless steel plate rack of size 900mm x 750mm with shelves, hooks and railing to keep plates vertically and horizontally,including necessary fixing arrangement, complete all as specified and directed. 162 S&F vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts,) complete incl making good to floor to match with adjoining surfaces, complete all as specified and directed. 163 S&F brass with CP finished, Jet spray with flexible pipe of suitable length fixed to 15mm bore pipe (faucet), complete all as specified and directed. 164 S&F in repair plastic water closet seat cover white closed pattern with flat bottom mild steel chromium plated or aluminium hinging device, complete all as specified and directed. 165 S&F in repair 10 Ltrs capacity virgin polypropylene cistern, symphonic action type, ISI marked, white at low level complete with PVC bends, flush pipe and making all connections with and incl inlets ball valve float, handle, brackets and making good the disturbed surfaces in CM 1:3 to match with the existing surface, complete all as specified and directed. 166 S&F in repair vitreous china wash hand basin white flat back or angle back type size 600mm x 480 mm white inclwaste pipe and prop stopper but incl cutting for and pinning in ends of brackets or erecting stand fixed, complete all as specified and directed. 167 S&F in repair CP shower rose heavy duty with swivel joints 125 mm dia fixed to15mm GI pipe, complete all as specified and directed. 168 Dismantling of 100mm cast iron or reinforced concrete drain pipe, jointed in cement mortar and taking out of trenches/ floor/ wall if required, complete all as specified and directed. 169 S&F 110mm dia PVC (SWR) junction double, (double/ single T), equal or un equal with oval accesse door including jointing with solvent cement as required, complete all as specified and directed. 170 S&F 110mm dia PVC (SWR) P /S trap single, equal or un equal of any length including jointing with solvent cement as required complete all as specified and directed. 171 S&F 75mm dia PVC (SWR) junction double, (double /single,T), equal or un equal with oval accesse door including jointing with solvent cement as required, complete all as specified and directed. 172 M&L for complete removal of old plastered surfaces of walls and applying two coats ofexterior emulsion paint & over one coat of primer etc., complete all as specified and directed. 173 M&L for preparation of old decorated plastered / unplastered surfaces of ceiling one coat of white wash on ceiling andAC plain building board surfaces as in ceiling complete all as specified and directed. 174 Complete removal of existingold surfacesapplying two coats of oil bound distemper over one coat of wall putty(2mm) on walls, complete all as specified and directed. 175 M&L for roof treatment by cleaning of roof slab surfacesincludingsweeping clean and washing down with water to remove dust & providing water proofing treatment with polymeric standard water proofing membrane complete all as specified and directed as under: (a) M&L preparation of plaster surfaces /RCC roof surfaces and applying one coat of oil bound bituminous primer @ 0.30 Ltr/sqm (b) Applying one coat ofbitumen 85/25 grade @1.2 kg/sqm (c) Supplying and laying modified polymeric water proofing membrane super thermo 3mm thick of weight not less than 3kg /sqm reinforced with polyesternon woven fabric weight not less than 150gm/sqmcenter core including coping on the surfaces with torch application of membrane with 10cm over laps as required.(d) Applying two coats of aluminium paint @ 0.20 kg/Sqm 176 M&L for water proofing treatment of sunken floor of WCs, Bathroom etc. by applying of the folling specifications:-(i) Cleaning of sunken floor surface with mechanical means i.e. wire brush/air blower etc. And remove all loose/unsound material, dirt, dust, etc.(ii) Applying cement slurry mixed with acrylic based polymer modified cementitious composite compound coating Hydro proof Xtra of FOSROC/Equivalent of Dr Fixit of pidilite industries Ltd in the ration of 1:2:4(One part of acrylic polymer : Two part of water and four part of cement).(iii) First layer of cement slurry @ 0.444 Kg/Sqm mixed with acrylic based modified cementious composite compound @ 0.222 Liter/Sqm and allow it to air dry for 04 Hours.(iv) Second layer of cement slurry @ 0.222 Kg/Sqm mixed with acrylic based modified cementious composite compound @ 0.111 Liter/Sqm and allow it to air dry for 04 Hours followed with water curing for 48 hours.(v) 200 micron thick polythene film shall be pasted with help of adhesives over treatment.Note:- Joints of WC/ Trap/ Soil waste shall be properly sealed with sealing compond.Testing of all traps and joint and sunken slab shall be done as per IS-1742 before filling and tiling work. 177 M&L for PCC 1:4:8, type D-2, using 40mm graded crushed stone aggregate, as in filling of mass concrete for floors, complete all as specified and directed. 178 M&L for 40mm thick, PCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in base coarse for floors, complete all as specified and directed. 179 Taking down carefully copper/ aluminum point wiring (light, fan socket or power) complete incl. (fitting such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc.), removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc., complete all as specified and directed. 180 M&L for point wiring 1.5 Sqmm (nominal cross sectional area) with colour coding multistranded copper conductor cable, PVC insulated (FRLS-H) and unsheathed cable and including drawn through PVC Casing-N-Capping of 25x32mm size with all fittings and accessories, terminated to PVC board of suitable size for housing/ mounting the switches/sockets including 1.5 Sqmm PVC insulated unsheathed multistranded copper conductor cable earth wire connected to common earth dolly for one light point control by one, one way switch complete all as specified and as directed. 181 All as per Srl Item No 180.00 above but for one 3 pin socket outlet 5 amps, onindependent board, complete all as specified and directed. 182 All as per Srl Item No 180.00 above but for one 3 pin socket outlet 5 amps, onsame board with other switches, complete all as specified and directed. 183 All as per Srl Item No 180.00 above but for one 3 pin 15 Amps power point on independent board with 2.5 Sqmm size FRLS-H PVC insulated unsheathed multistranded copper conductor cable and with 2.5 Sqmm FRLS-H, PVC insulated unsheathed multistranded copper conductor as earth wire, complete all as specified and directed. 184 S&F switch piano flush single pole, one way 5 Amp (ISI marked)complete all as specified and directed. 185 S&F switch piano flush single pole, one way 15 Amp ( ISI marked)complete all as specified and directed. 186 S&F socket (ISI Marked) 2 in 1, 3 pin 5/6 amps flush type, complete all as specified and directed. 187 S&F socket 2 in 1, 5 pin 5 and 15 amps (ISI marked) flush type universal, complete all as specified and directed. 188 S&F ceiling rose, 3 phase, PVC polycarbonate, insulated body (ISI Marked), complete all as specified and directed. 189 S&F LED inverter batten tube light along with fixture, 1x 20 watt, (4 Feet) wall mounted LED batten, with diffuser, complete including electrical connection with copper cable from ceiling rose to fittings and including taking down existing fittings and all fixing arrangements complete all as specified and directed. 190 M&L for lamp holder (Angle) PVC /Polycarbonate type with back plate suitable for batten fittings, including LED 15 Watt lamp, complete all as specified and directed. 191 S&F LED building security light 25 watt fixed on wall suitable bracket with all connected accessories complete including electrical connection with copper cable from ceiling rose to fittings and including taking down existing fittings and all fixing arrangements complete all as specified and directed. 192 S&F LED tube light along with fixture, 1x 10 watt, (2 Feet) wall mounted LED batten, extruded PVC, heat sink provided for efficient heat dissipation & integrated electronic driver, optics diffused, complete including electrical connection with copper cable from ceiling rose to fittings and including taking down existing fittings and all fixing arrangements complete all as specified and directed. 193 S&F LED light fitting 9/10W bulk head luminaire including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size including taking down old unsv existing fittings complete all as specified and directed. 194 S&F in replacement 36/40W LED (Size 2x2) square shapedrecess mounting type luminaire having white polycarbonate body & alumium heat shrink with PMMA diffuser, 5700Kincluding connecting three core copper cable up to ceiling rose complete with separate electronic driver & high brightness LEDs white colour, complete all as specified and directed. 195 M&L for submain wiring with 2X6.0 Sqmm+1X6.0 Sqmm Earth Wire single core PVC insulated FRLS-H, PVC sheathed cooper cableconnecting to common earth dolly in and including heavy duty PVC casing-N-capping, with all accessories complete all as specified and directed. Note: Three runs of copper wire for phase, neutral, earth & one run PVC conduit/ casing shall be measured one unit length. 196 S&F VTPN MCCB distribution board 4 way fabricated out of thick high quality CRCA sheet, DBs shall be totally enclosed, suitable for 240V/415V, having polyurethane (PU) foam gasket to ensure IP-54 degree of protection for indoor application aspre IEC 61439-3:2012 (CI. 10.3)/IEC 60529.DB shall be robust with tested for impact resistance IK09as per IEC 61439-3:2012(CI.No. 10.2.6).DBs shall be provided with prefitted cement Guard. DB Door shall have detachable gland plates provided with proper knockout holes of 26mm/35mm diameter for insertion of cable /conduits. Distribution Boards shall bre provided with wire set of copper along with the insulated fork type bus bars Including MCCB 100 Amp 4 Pole ICU = ICS = 25 KA - 01 Nos. . DB shall have reversible hinged doors and possibility to allow door opening from left to right or right to left for convenience on site. DBshall have type test reports as per IEC 61439-3 from ERDA or NABL laboratory, complete all as specified and directed. Make: Indoasian Cat part No 812040 or equivalent in L&T / Schneider/ Seimens/ Hager 197 S&F sheet metal enclosure MCB, DB, 8 way, SPN, double door suitable for 240 V, 200 amps rated bus bar/ DIN rail, fixed and flushed on walls including cutting Knitch and making good disturbed surfaces, complete all as specified and directed. Make : L&T / Legrand / Schineider. 198 S & F MCB, SP (single pole ) 05 to 32 Amps, 10 kA, B curve for inductive load connected through cable lugs of suitable size, complete all as specified and directed. Make : L&T / Legrand / Schineider. 199 S&F MCB, SPN (single pole and neutral ) 40 Amps for inductive load connected through cable lugs of suitable size, complete all as specified and directed. Make : L&T / Legrand / Schineider. 200 S&F electric water heater, storage type steel body with SS inner tank and heating element upto 2 KW capacity 50 Liter, BEE 5 Star rated, complete with all accessories such as safety valve, thermostat, NRV, connection piece etc. and fixing arrangements, complete all as specified and directed. 201 S&F 15/20 Amp, Socket with 16/20 Amp, MCB with metal box combination (ISI marked) flush type universal complete all as specified and directed. 202 S&F exhaust fan, AC single Phase 230V, steel body of size 230m sweep with blades and frame and louvers complete all as specified and directed. 203 S&F exhaust fan, AC single Phase, 230V, steel body of size 380m sweep with blades and frame and louvers, complete all as specified and directed. 204 Supply and laying Aluminium strip 25 x 3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground, complete all as specified and directed. 205 S&F Air termination, single pointed aluminium rod 12mm dia and 300mm long, complete all as specified and directed. 206 S&F test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw, complete all as specified and directed. 207 M&L for Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion including galvanised strip protected by 32 mm bore light grade galvanised iron pipe and earth and connected to test point as directed including funnel, watering pipe 20 mm bore light grade galvanised iron wire mesh charcoal and common salt in alternate layers of 15 cm compacted thickness all around the GI electrode with concrete pit in PCC 1:3:6, type C-1, includingnecessary excavation in soft/loose soil and disposal of soil to a distance not exc 50 m and necessary testing complete connected to earthing test point, complete all as specified and directed. 208 All as per Srl Item No 207.00 above but for using galvanised iron strip 32x6mm as earthing lead, complete all as specified and directed. 209 M&L for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/ pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire, complete all as specified and directed. 210 All as per Srl item No 209.00 above but for 32x6mm, galvanised iron strip, complete all as specified and directed. 211 M&L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 sqmm, 3.5 core, complete all as specified and directed. 212 Supply, fixing or layingHDPE (DWC) tubing 40mm dia as per IS:16205 part 24 fixing on poles, walls under floors, laying on surface etc. as reqd at site complete all as specified and directed. Note: All items and accessories, bend,joints, nut bolts, clamps for wall fixing as per site requirement etc. are incl in quoted rates. 213 M&L and installation for Electric chimney suitable for 4 to 6 burner up to 5 feet and suction upto 1500 cum/hour with copper winding motor, auto cleaning facility, low noise level fable filter type complete all as specified and directed. 214 M&L for point wiring 1.5 Sqmm (nominal cross sectional area) with colour coding multistranded copper conductor cable, PVC insulated (FRLS-H) and unsheathed cable and including drawn through PVC conduit 20mm concealed wiring with all fittings and accessories, terminated to sunken box and laminated sheet of suitable size for housing/ mounting the switches/sockets including 1.5 Sqmm PVC insulated unsheathed multistranded copper conductor cable earth wire connected to common earth dolly for one light point control by one, one way switch, complete all as specified and as directed. 215 All as per Srl item No 214.00 above but for One bell/ buzzer point controlled by one push button, complete all as specified and directed. 216 All as per Srl item No 214.00 above but for two way switches, complete all as specified and directed. 217 All as per Srl item No 214.00 above but for one 3 pin socket outlet 5 amps, onindependent board, complete all as specified and directed. 218 All as per Srl item No 214.00 above but for one 3 pin socket outlet 5 amps, onsame board with other switches, complete all as specified and directed. 219 All as per Srl item No 214.00 above but for one 3 pin 15 Amps power point on independent board with 2.5 Sqmm size FRLS-H, PVC insulated unsheathed multistranded copper conductor cable and with 2.5 Sqmm FRLS-H, PVC insulated unsheathed multistranded copper conductor as earth wire, complete all as specified and directed 220 S&F Bell push, flush type, 5 amp ( ISI marked), complete all as specified and directed. 221 S&F switch piano flush single pole, two way 5 Amp ( ISI marked), complete all as specified and directed. 222 S&F Bell, AC, 230 volts, single pole,complete all as specified and directed. 223 S&F LED building security light 40 watt fixed on wall suitable bracket with all connected accessories complete including electrical connection with copper cable from ceiling rose to fittings and including taking down existing fittings and all fixing arrangements, complete all as specified and directed. 224 S&F LED light fitting 20W bulkhead luminaire including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size including taking down old unsv existing fittings, complete all as specified and directed. 225 S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 liter, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece etc. and fixing arrangements, complete all as specified and directed. 226 S&F exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm including fixing all arrangements, complete all as specified and directed. 227 S&F exhaust fans AC single phase 230/ 240 V of size 300 mm sweep metal body with louver including fixing all arrangements, complete all as specified and directed. 228 S&F AC single phase static energy meter of accuracy class 1.0, 240 V, 50 Hz with Backlit LCD display of rating 5 - 30 A, (measures and displays KWH ,V, Current I, KW, pf last month history of KWH, MD in KW) with special features like TOD, temper logging, optical communication port display in absence of power with transparent hinge type boxincluding fixing all arrangements, complete all as specified and directed. 229 S&F sheet metal enclosure MCB DB 12 waySPN double door suitable for 240 V, 200 amps rated bus bar/ DIN rail, fixed and flushed on walls including cutting Knitch and making good disturbed surfaces complete all as specified and directed. Make: L&T /Legrand/ Schneider. 230 S&F MCB, TPN (Triple pole Neutral) 40/63 Amps for inductive load connected through cable lugs of suitable size complete all as specified and directed. Make:L&T/ Legrand /Schneider. 231 S&F sheet metal enclosure MCB DB 4 wayVTPN double door suitable for 240 V, 200 amps rated bus bar/ DIN rail, fixed and flushed on walls including cutting Knitch and making good disturbed surfaces complete all as specified and directed. Make:L&T/ Legrand /Schneider. 232 S&F 4 Pole, MCCB, 63 Amp, 50 Hz, 415 V with rupturing capacity 36 KA, connected through cable lugs of suitable size complete all as specified and directed. Make:L&T/ Legrand /Schneider.
