Tender For Special Repair To Bldg No E 37 P 45 P 46 And Dd 03 Under Ge (West) Ferozepur Cantt; 1 Demolition of un-reinforced cement concrete of any description and in any position not otherwise specially provided for complete all as specified and directed. 2 Demolition of concrete in ground floors and pavings not exceeding 15cm thickness (below or above ground level) complete all as specified and directed. 3 Demolition of brick workbuilt in cement mortor including all quoins,arches,pillars etccomplete all as specified and directed. 4 Taking up or down existing 15mm bore steel water tubing and connections,including clreaning for refixing or removal, fixed/laid in any situation, complete all as specified and directed. 5 Taking up or down existing 20mm bore steel water tubing and connections,including clreaning for refixing or removal, fixed/laid in any situation, complete all as specified and directed. 6 Dismantlingwrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. 7 Dismantling timber scantlings 40 sqcm and over in section,in any position in unframed work complete all as specified and directed. 8 Dismantling 100mm borecast iron or PVC orreinforced concrete drain pipes, jointed in cement mortar and taking out of trenches and taking down from walls, if required complete all as specified and directed. 9 Dismantlingasbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed. Hacking out old broken glass (any size, thickness, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed. 10 Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories)complete all as specified and directed. 11 Taking down cement plaster of any descriptionon brick walls or concrete or stone and ceilingsincludingracking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. 12 Dismantling floor, hearth or wall/stone tiling including cement mortar bedding (but not backing), removing broken tiles and rubbish off the premises from site complete all as specified and directed. 13 Taking down chowkats or frames with shutters (without taking off shutters from the frame) of size not exceeding 1.5 Sqm each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts, and removing from site complete all as specified and directed. 14 Taking down chowkats or frames with shutters (without taking off shutters from the frame) of size exceeding 1.5 Sqm but not exceeding 4 Sqmeach including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts, and removing from site complete all as specified and directed. 15 Taking down dhutters of any description exceeding 1.00Sqm but not exceeding 2.00Sqm each and removing from site complete all as specified and directed. 16 Dismantling brick tiles or terracing tiles, single layer on roofs jointed and pointed in cement mortar including removal of grass vegitation including roots near out let of RWP and OHT staging area or specifically ordered in writing complete all as specified and directed. 17 Demolition of mud phuska in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part hereof ) complete all as specified. Note :- Demolition of Mud puska to be cut in average thickness from top surface of roof for creating the slope as directed 18 Dismantling boarding, any description, fixed in any postion with nails or screws complete all as specified and directed. 19 Demolition of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, complete all as specified and directed. 20 Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed. 21 Excavating in trenches, in soft/loose soil, not exceeding 1.5m wide and not exceeding 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, cables and pipes etc. not exceeding 10Sqm on plan and not exceeding 1.5m in depth and getting out completeaii as specified and as direcetd. 22 Returning, filling in,including spreading, leveling, watering and well ramming in layers not exceding 25cm in soft/loose soil complete all as directed. 23 Removing excavated materials to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed. 24 M&L for Hardcore of broken stones and boulders ofgauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed. 25 M&L forLean Cement Concrete (1:3:6) type C-1 using 20mm gradedcrushed stone aggregate as in foundations, filling andmass concrete and filling back sides of pressed steel framescomplete all as specified and directed. 26 M&L for brick work built in cement mortar (1:6) with sub class B old size bricks, straight or curved on plan exceeding 6m mean radius complete all as specified and directed. 27 M&L for brick work (EXCEPT BRICKS) built in cement mortar (1:6) with sub class B old size bricks, straight or curved on plan exceeding 6m mean radius complete all as specified and directed.Note:- Old seviceable tiles shall be re-used retrieved after demolition of brock work. 28 M&L for Plain Cement Concrete (1:2:4) type B-1 using 20mm graded stone aggregate in Covet fillet minimum radius of 75mm as in roof and parapet wall junction,roof benching, kerbs, mud stop, coping, rounded or chamfered on edges, slopingon roofincluding form work complete all as specified and directed. 29 S&F factory made pressed steelframes made out of 1.25mm CRCA sheetframe of profile 125mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock plate, etc.,including one shop coat of priming and 10mm dia round mild steel bar in thresholdcomplete all as specified and directed. 30 S&F factory made pressed steelframes made out of 1.25mm CRCA sheetframe of profile 105mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock plate, etc.,including one shop coat of priming and 10mm dia round mild steel bar in thresholdcomplete all as specified and directed. 31 Fixing only in repairs second class hard-wood clean sawn in scantlings to replace old and decayed timber(including piecing,scarfing,etc of old and new timbers if required) and removing defective portions to store complete complete all as specified and directed. 32 S&F factory made35 mm thickglazed and skeleton shutters 2nd class hard wood (except Mango) open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitered beads for securing glass etcfor doors,The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated,complete all as specified and directed. 33 S&F factory made40m thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, laminated with 0.9mm thick decorative laminate type 1 of surface finish, colour and pattern approved, fixed with approved adhesive as per manufacturers instructions including 6mm thick teakwood lipping fixee with adhesive and headless nails complete all as specified and directed. 34 S&F Anodised aluminium window and ventilator shutters, powder coated aluminium (minimum thickness of powder coating 50 micron) side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified complete all as specified and directed. 35 S&F in replacement Factory Made Box Type Steel Windows with glazing bars made of ERW tube hollow P section of size 60mmX25mm double rebated outer frame comprising double shutters side hung skelton & glazed shutters, frame of ERW tube P section size50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and mild steel flat iron 2mm thick welded/ screwed to frame for fixing of wire gaugeto frame/ shutters as given below and all as shown on Drawing No. CEJZ/TD-1019/08 and CEJZ/TD-1020/08 Sheet No.1/3 to 3/3 including taking down of old existing window complete all as specified and directed :-(i) Hold fast,150mm long of flat iron 12mmX3mm- 04Nos per window(ii)Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iii)MS Tower bolt 150mm long-02 Nos per leaf(iv)Z section 20mmX25mm,100mm long stopper -01 Nos per leaf(v)Cleat 55mm long of hollow square 15mmX12mm -02 Nos per leaf (vi)MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (vii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window).(viii) Preparation of steel surfaces of windows and grills and guard bars and applying one one shop coat of zinc chromate primer and two coats of synthetic enamel paint after installtion at site. Note: Glass panes and grills & guard bars shall be measured and paid for separately .Area shall be measured flat for one side only for the purpose of measurement and payment . 36 S&F in replacement Factory Made Box Type Steel Windows without glazing bars made of ERW tube hollow P section of size 60mmX25mm double rebated outer frame comprising double shutters side hung i.e. guagedshutters, frame of ERW tube P section size50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and mild steel flat iron 2mm thick welded/ screwed to frame for fixing of wire gaugeto frame/ shutters as given below and all as shown on Drawing No. CEJZ/TD-1019/08 and CEJZ/TD-1020/08 Sheet No.1/3 to 3/3 including taking down of old existing window complete all as specified and directed :-(i) Hold fast,150mm long of flat iron 12mmX3mm- 04Nos per window(ii)Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iii)MS Tower bolt 150mm long-02 Nos per leaf(iv)Z section 20mmX25mm,100mm long stopper -01 Nos per leaf(v)Cleat 55mm long of hollow square 15mmX12mm -02 Nos per leaf (vi)MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (vii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window).(viii) Preparation of steel surfaces of windows and grills and guard bars and applying one one shop coat of zinc chromate primer and two coats of synthetic enamel paint after installtion at site. Note: Wire cloth and grills & guard bars shall be measured and paid for separately .Area shall be measured flat for one side only for the purpose of measurement and payment . 37 S&F in replacement Factory Made Box Type Steel Ventilators top hung with glazing bars or dovetailed or welded made of ERW tube P-section of size 60mmx25mmouterframe ( single rebated), comprisesglazed shutter, frame of ERW tube and mild steel flat iron 2mm thick welded/screwed to frame for fixing ofsheet glassincluding fixture and fittingslike as Stopper, Cleat, Pintal hinges, holdfast etc all as shown onDrawing No. CEJZ/TD-1019/08 and CEJZ/TD-1020/08 Sheet No.1/3 to 3/3 including taking down of old existing window complete all as specified and directed:- Note : 1. Grills and guard bars, Sheet glass and wiremesh shall be measured and paid separately. 2. Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). 3. Preparation of steel surfaces of ventlators and applying one one shop coat of zinc chromate primer and two coats of synthetic enamel paint after installtion at site.4. Area shall be measured flat for one side only for the purpose of measurement and payment . 38 S&F framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. 39 S&F 50mmx47mm size solid PVC door framemade out of 5mm plain colour PVC sheetreinforced with MS square tube, complete all as specified and directed. 40 S&Ffactory made 30mm thick (style) solid panel PVC door shutterconsisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain / coloured PVC C channel having a PVC sheet strip of20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side and as gap insert for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the styles & rails with suitable PVC sheet beading and jointed togeather with solvent cement complete all as shown on drawings, specified and directed. 41 S&F factory made uPVC white colour casement (Openable) window Area not exceeding 1.00 sqm eachmade of extruded profiles with wall thickness of 2.3mm ( + – 0.2mm). Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 73mm), T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 +– 0.2mm thick, galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27.5mm). T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100mm long fasteners. Hardware: [casement handle made of zinc alloyed (white powder coated), But Hinges ofzinc alloyed (white powder coated), transmission gear made of mild steel with multi point locking system] and 5mm thick glazing with selected quality glass. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) complete all as shown on drawings, specified and directed. 42 S&F factory made uPVC white colour casement (Openable) window Area exceeding 1.00 sqm but not exceeding 2.00 sqm each made of extruded profiles with wall thickness of 2.3mm ( + – 0.2mm). Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 73mm), T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 +– 0.2mm thick, galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27.5mm). T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100mm long fasteners. Hardware: [casement handle made of zinc alloyed (white powder coated), But Hinges ofzinc alloyed (white powder coated), transmission gear made of mild steel with multi point locking system] and 5mm thick glazing with selected quality glass. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) complete all as shown on drawings, specified and directed. 43 S&F16-18mm solid PVC Board plain colour fixedwith screws or adhesive as in shutters complete all as specified and directed. 44 S&F 18mm thickPrelaminated particle board, exterior grade, prelaminated both sides with decorative choicelaminations, flat pressed, single or three layer type with BWP type phenol formaldihide adhesive as in cup board/ ward robe shutters and shelves including 6mm thick teak wood lipping on three sides of shutters and 20mm thick on hanging side fixed with glue and headless mild steel nails and shuuters fixed with screws to timber frame work complete all as specified and directed. 45 S&F 12mm thick Plywood, grade BWP, type BB fixed with screws to timber frame with 0.9mm thick Decorative laminate on one facetype 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturers instructions complete all as specified and directed. 46 S&F 5mm thick plain colour PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining, Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of Solvent Cement and fixing at site complete all as specified and directed. 47 S&F 100mm size mild steel butt hinges medium weight rolled cold complete all as specified and directed. 48 S&F 150mm long aluminium anodised barreltower bolts and fixed with steel screwscomplete all as specified and directed. 49 S&F 200mm long aluminium anodised barreltower bolts and fixed with steel screwscomplete all as specified and directed. 50 S&F 150mm size aluminium door handle, extruded aluminium alloy, fabricated type complete all as specified and directed. 51 S&F 125mm size aluminium door handle, extruded aluminium alloy, fabricated type complete all as specified and directed. 52 S&F 75mm size aluminium door handle, cast type, anodised complete all as specified and directed. 53 S&F 125mm size mild steel pressed handle, oval type, stove enameled black complete all as specified and directed.5 54 S&F stainless steel continous (piano) hinges of mild steel bright finish or electro galvanised with flap (when open) 30mm,fixed with steel screw complete all as specified. 55 S&F 300mm long mild steel sliding door bolt, plate type, stove enameled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple platecomplete all as specified and directed. 56 S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed. 57 S&FFloor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, with 150mm overall length of cover platefixed in floor complete all as specified and directed, 58 S&F 300mm size mild steel helical door spring ordinery rat rail rod pattern spring including roller and roller plate complete all as specified and directed, 59 S&F 100mm size hasp and staple aluminium anodised including bolt to hinge plate and fixed with screws complete all as specified and directed, 60 S&F in repairs 20mm dia Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and directed 61 S&F Stainless Steel WireCloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. 62 S&F in repairs Stainless Steel WireCloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. 63 S&F 4.8mm thick, plainsheet glass, ordinary quality and glazing,with oil putty or with wooden beads(supplied alongwith shutters), in squares n.exc 0.50 Sqm in each pane complete all as specified and directed. 64 S&F 3.0mm thick, plainsheet glass, ordinary quality and glazing,with oil putty or with wooden beads(supplied alongwith shutters), in squares n.exc 0.50 Sqm in each pane complete all as specified and directed. 65 S&F 4.0mm thick, figured glass, pin headed type and and glazing,with oil putty or with wooden beads(supplied alongwith shutters), in squares n.exc 0.50 Sqm in each pane complete all as specified and directed. 66 S&F Structural SteelFe-410- W(Gde E-250) quality B Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and directed. 67 S&F 10mm dia and over mild steel TMT bars , cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm diacomplete all as specified and as directed. 68 M&L for plain cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in roof padding, roof kerbs or mud stops, bed blocks, benching etc including necessary form work complete all as specified and directed. M&L for reinforced cement concrete (1:2:4) type B-1, using 20 mm graded crushed stone aggregate as inmanhole slabs,and the likeincluding weathering, slightly rounded or chamfered angles and throating, as directed including necessary form work etccomplete all as specified and directed. (Note : Reinforcement shall be measured and paid for separately ) 69 M&L for 75mm thick Plain Cement concrete (1:3:6) type C-1 using 20mm graded stone aggregate as in plinth protection, surfaces finished even and smooth without using extra cement as in plinth protection including provision of construction joints and expansion joints filled with bitumen mixed with sand in ratio (1:1) complete all as specified and directed. 70 M&L forPlain Cement Concrete (1:2:4) type B-1 using 20mm gradedcrushed stone aggregate as in sub base of flooring, surface finished rough to receive floor topping, surface finished even and fair complete all as specified and directed. 71 M&L for75mm thick Plain Cement Concrete (1:4:8) type D-2 using 40mm gradedcrushed stone aggregate as in sub base of flooring,surface finished rough to receive floor topping, surface finished even and fair complete all as specified and directed. 72 M&L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over and including 15mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and directed. 73 M&L for Machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 15mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and directed. 74 M&L for Machine cut kota stone slab 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, in vertical surfaces such as skirtings, dados, risers and steps etcincluding rubbing and polishing complete over and including 10mm thick screed bed or bedding layer in cement mortar (1:4) complete all as specified and directed. 75 M&L for Mirror polishing on marble/ granite/ Kota stone/ stone work where ever required to give high gloss finishcomplete. complete all as specified and directed. 76 M&L for 7 to 8 mm thick (square/ rectangular) Non-skid Ceramic Tiles coloured, premium quality,area of each tile exceeding 0.18Sqm but not exceeding 0.38Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including 15mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and directed. 77 M&L for 7 to 8 mm thick (square/ rectangular) Non-skid Ceramic Coloured Tiles, premium quality,area of each tile exceeding 0.11Sqm but not exceeding 0.18Sqm, in vertical surfaces such as skirtings, dados, risers and steps etcset and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including 10mm thick rendering cement plaster in cement mortar (1:4) complete all as specified and directed. 78 M&L for 7mm thick(Area 450 x 300mm / 450x350mm)Glazed Ceramic Coloured Tiles,in vertical surfacesX 7 mm th set and jonnted in cement slurry and pointed in white or coloured cement in vertical surfaces such as skirtings, dados, risers and steps etcset and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including 10mm thick rendering cement plaster in cement mortar (1:4) complete all as specified and directed. 79 M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paverblocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. 80 M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete complete all as specified and directed. 81 M&L for 10mm thick rendering cement plaster in cement mortar (1:6) on fair faces of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. 82 M&L for 15mm thick rendering cement plaster in cement mortar (1:6) on fair faces of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. 83 M&L for 15mm thick rendering cement plaster in cement mortar (1:4) on other than fair facesof brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. 84 M&L for 5mm thick rendering cement plaster in cement mortar (1:3) on ceiling surfaces, finished even and smooth without using extra cement complete all as specified and directed. 85 M&L for 10mm thick screed bed or bedding layer in cement mortar (1:4) mixed with water proofing compound @ 3% by weight of cement or as per manufacturers instructions, finished even and smooth without using extra cement on roof surfaces to have a smooth and uniform surface for laying of water proofing membrane complete all as specified and directed. . Note: WPC shall be measured and paid separately. 86 Supply only Liquid water proofing compound complete all as specified and directed. 87 M&L for applying bond coat of epoxy bonding agent & cement mortor in 1:1 ratio for bonding old and new concrete on damaged surfaces applying ready mix polymer modified mortar upto 60mm thickness (Chajjas fins, border,slab, beams etc) :-(i)Including application of rust remover on exposed reinforcement and subsequent application of anticorrosive coating. Also, pressure grouting with epoxy injection after application of polymer modified mortar.(ii)Use of electrical mixer to get the homogeneous dough on bond coat surfaces.(iii)To achieve required thickness repeat this step after 24 hrs as required.(iv) Keep the surfaces moist using water forg for 5 to 7 days etc complete all as specified and as directed.(v)Rate shall be inclusive of all necessary scaffolding for building height up to 24 meters complete all as directed by Engineer-in-Charge.Make of Chemicals : - Epoxy bonding agent, Rust remover, Anti corrosive coating, Polymer modified mortar, Epoxy grout shall be of Berger Krishna/Dr Fixit/MC Bauchemie & M/s Cemistik/Sika or Equivalent as approved by GE.Notes : (i) Complete treatment to be executed by approved applicator (Applicator to be approved by GE).(ii) The Contractor and manufacture of polymer modified mortar shall give the warranty before commencement and also for the strengths achievedin the postcompletion of work.(iii) The chemicals to be used in the work shall be certified by the manufacturer with whom the MOU been entered into. (iv) Hard drawn steel wire fabricwill be measured and paid seperately. complete all as specified and directed. 88 M&L for Water proofing treatment to sunken floors of kitchen, toilets, laboratories, bath and WCs etc shall be as under :- (i) Application of Two component Acrylic modified Cementitious coating (aa) The surfaces to be applied shall be completely dry and free from containments such as dirt, dust, oil, surface treatments and old coatings. Concrete substrates must be mechanically prepared using abrasive blast cleaning or milling to remove cement laitance, existing coatings and achieve a gripping profile that is clean, dry and free from litance and any other form of surface contamination. The installation instructions in manufacturers published literature should be strictly complied with including but not limited to the following:- (bb) Chipping out any visible cracks in V-Groove pattern as applicable. Special attention on this part Cleaning of cracks & then filling those cracks with SIKA latex SBR 100 putty/ Dr Fixit 302 SBR late Perma latex SBR / FOSROC Nitabond SBR latex / Asian Paints latex as required. Final cleaning surface with power grinder, wire brush, hair brush & vacuum pressure if required. (cc) Dampen all surfaces immediately ahead of application of Acrylic modified Cementitious coating Sika Top Seal - 107/ Brush Bond FOSROC/ Dr Fixit/ STP/CICO.(dd) Whilst the surface is still damp from saturation (S.S.D), apply one coat of Acrylic mo Cementitious coating of Sika Top Seal - 107 / Brush Bond FOSROC/ Dr Fixit/ STP/CICO of vis as per manufacturers instructions. (ee) Apply Glass Fabric Sheet of Sika Fab 1/FOSROC/ Dr Fixit/ STP whilst the first coat is wet(ff) Once touch dry, apply second coat of Acrylic modified Cementitious coating of Sika Top Sea /Brush Bond FOSROC/ Dr Fixit/ STP/CICO of viscosity as per manufacturers instructions entire area. (gg) Second coat shall be applied after 6-8 Hrs of application of previous coat and in the direct angle to the previous coat. (hh) The waterproofing coating should be taken to a height minimum 300 mm above the floor finish level on the vertical surface. (jj) It is essential to cure Acrylic modified Cementitious coating immediately after application 3-8 Hrs drying) for a minimum of 3 to 5 days to ensure full cement hydration and to minimize leakage/seepage.(kk) A protection plaster (12-15mm thick) in CM 1:3 admixed with appropriate Integral water proofing Compound has to be applied on the wallsAdmixture :- Sika plastocrete plus/FOSROC/Dr Fixit/STP/CICO confirming to IS 2645Providing and applying a protection screed of 50 mm thick 1:4 cement sand mortar admixed with Sika plastocrtete over applied water proffing coating on horizontal surface.Admixture :- Sika plastocrete plus/FOSROC/Dr Fixit/STP/CICO confirming to IS 2645(ii) All the corners and joints should be pretreated with elastic waterproffing sealing tape with a woven bonding on each surface an elastic expansions zone in the centre of make sika Tape S/FOROC/Dr Fixit/STP(mm) The membrane has to be protected in accrodance with the manufactures recommendance until placemnent of concrete. The membrane to be inspected for damage just prior to concrete placement and make repairs in accrodance with manufacturers recommendations. (nn) Waterproffing treatement has to carried out through applicators authorisrd.(ii) All the joints of pipesand traps within sunken portion shall be sealed properly by Epoxy sealant.(iii) All CI traps in sunken slab to be enclased with PCC 1:1:5:3 ( Min15 cm) all - round.(iv) the sunken portion shall be filled with PCC 1:5:10 type E-2 (using 40 mm stone aggregate) complete all as specified.(v) Providing drainage spout pipe GI 40 mm dia bore light grade upto outside of outer wall (approx 450 mm to 600 mm long) including cutting to existing wall and making good the distrubed surface complete all as specified and directed.(vi) Providing 25 mm thick cement concrete 1:2:4 type B-0 using 12.5 mm grade stone aggregate as in flooring for laying fllor finish all as specified. Note ;- Item No 116 (aa) to (nn) shall be measured and paid in this item only, no extra item be taken for these items. 89 M&L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.20 kg per sqmover a coat of bitumen primer @ 0.30 litre per Sqm including preparation of roof surfaces complete all as specified and directed. 90 M&L APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced applicationcomplete all as specified and directed. 91 M&L for preparation of surfaces of platered, brick, concrete, polymeric etc, of any description, over10cm in width or girth,not otherwise describedone and applying two coats of Solar Reflective Bituminous Aluminium paint @0.1 Kg/ Sqm over APP Membrane complete all as specified and directed. 92 M&L for 40mm thick brick tiles laid on mud mortar or mud phuska and joints grouted flush and pointed flush as the work proceeds in cement mortar (1:3) mixed with 5% of crude oil by weight of cementcomplete all as specified and directed. 93 M&L for 40mm thick brick tiles (EXCEPT TILES) laid on mud mortar or mud phuska and joints grouted flush and pointed flush as the work proceeds in cement mortar (1:3) mixed with 5% of crude oil by weight of cementcomplete all as specified and directed. Note:- Old seviceable tiles shall be re-used retrieved after dismantling brick tiles on roofs/terrace. 94 S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and directed. 95 S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified complete all as specified and directed. 96 S&F 6mm thick fancy designed Exposed metal frame ceiling with calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid (Frame work for ceiling shall be measured and paid separately) complete all as specified complete all as specified and directed. 97 S&F0.50mm thick Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheetof an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screw complete all as specified complete all as specified and directed. 98 S&F0.50mm thickPre- painted galvalume aluminum zinc coating GI based plain steel sheetof an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screw complete all as specified complete all as specified and directed. 99 M&L forpreparing new plastered surfaces of walls anddistempering with two coats of distemper oil emulsion white or tinted over 01mm thick plaster of paris putty to prepare surface even and smooth complete all as directed. 100 M&L forpreparing new plastered surfaces of walls andapplying two coats of cement base paint over one coat of alkali resistant cement primer complete all as specified and directed. 101 M&L forpreparing new plastered surfaces of walls andapplying three coats of lime white wash complete all as specified and directed. 102 M&L forpreparing old plastered surfaces of walls including washing, rubbing down and stopping distempered and painted surfaces anddistempering with one coat of distemper oil emulsion white or tintedcomplete all as directed. 103 M&L forpreparing old plastered surfaces of walls andapplying one coat of cement base paint complete all as specified and directed. 104 M&L forpreparing old surfacesdecorated plastered or unplasteredsurfaces ofwalls and applying one coat of lime white wash complete all as specified and directed. 105 M&L forpreparing old plastered surfaces of ceiling andapplying one coat of lime white wash complete all as specified and directed. 106 M&L for preparation of new wood or wood basedsurfaces of any description, not otherwise described,over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primercomplete all as specified and directed. 107 M&L for preparation of new wood or wood basedsurfaces of any description, not otherwise described,over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primercomplete all as specified and directed. 108 M&L for preparation of new steel and iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer zinc chromate complete all as specified and directed. 109 M&L for preparation of old wood or wood basedsurfaces of any description, not otherwise described,over 10cm width or girth and applying one coat of synthetic enamel paint over one coat of pink primercomplete all as specified and directed. 110 M&L for preparation of old steel and iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all asspecified and directed. 111 S&F 75mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, fixed to wallscompleteall as specified and directed. Note:- Only Pipe along the centre line shall bemeasured and paid except fittings and accessories which shall be measured and paid for separately under respective items.) 112 S&F 110mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, fixed to wallscompleteall as specified and directed.Note:- Only Pipe along the centre line shall bemeasured and paid except fittings and accessories which shall be measured and paid for separately under respective items.) 113 S&F 75mm dia PVC (SWR) bends any radiuscomplete all as specified and directed. 114 S&F 110mm dia PVC (SWR) bends any radiuscomplete all as specified and directed. 115 S&F 75mm dia PVC (SWR)Junction single (single or double T) equal or unequalcomplete all as specified and directed. 116 S&F 110mm dia PVC (SWR)Junction single (single or double T) equal or unequalcomplete all as specified and directed. 117 S&F 75mm dia PVC (SWR) vent cowlcomplete all as specified and directed. 118 S&F 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed. 119 S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed. 120 S&F 15mm bore Galvanised Medium Grade Steel Water Tubing with all fittings and connectionsfixed complete to walls and celling or laid in floor, complete all as specified and directed. 121 S&F 20mm bore Galvanised Medium Grade Steel Water Tubing with all fittings and connectionsfixed complete to walls and celling or laid in floor, complete all as specified and directed. 122 S&F 15mm bore Unplasticiscd PVC pipes of pressure rating 10 kgf/cm2with all fittings and connections laid in trenches complete to walls and ceilings or laid in floors complete all as specified and directed. 123 S&F 20mm bore Unplasticiscd PVC pipes of pressure rating 10 kgf/cm2 with all fittings and connections laid in trenches complete to walls and ceilings or laid in floors complete all as specified and directed. 124 S&F in repairs 15mm bore Bib Taps,fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down,screwed for iron pipe or brass ferrule complete all as specified and directed. 125 S&F 15mm bore Bib Taps, long bodyfancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down,screwed for iron pipe or brass ferrule complete all as specified and directed. 126 S&F 15mm borefancy type, chromium plated, Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unionscomplete all as specified and directed. 127 S&F 15mm borefancy type, chromium plated, Stop valves, cast copper alloy, with long shank and cup concealed type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unionscomplete all as specified and directed. 128 S&F 20mm boreGun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipescomplete all as specified and directed. 129 S&F 32mm bore Waste fittings of chromium plated brass p for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed. 130 S&F 15mmPVC connections 450mm long heavy duty with brass nuts adaptors andwashers and rubber gaskets at both ends complete all as specified and directed. 131 S&F 15mmPVC connections 600mm long heavy duty with brass nuts adaptors andwashers and rubber gaskets at both ends complete all as specified and directed. 132 S&F 15mm bore Angle Valves, fancy type, chromium plated, cast copper alloy,with flange, one way turn, screwed down high pressure, with crutch or butterfly handle, screwed for iron pipecomplete all as specified and directed. 133 S&F in replacement 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), three layered, ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including 20mm dia ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule histed and fixed including dismentling andtaking down old unserviceable water tank capacity 500 litres complete as specified in SSR Part-I. complete all as specified and directed. 134 S&F in repairs Wash Hand Basins, Vitreous China (flat back) white of size 550mm X 400mm including cutting for and pinning in ends of brackets or erecting standincluding waste fittings, 32 mm bore PVC flush pipe with long screwed shucks and fly nuts and including PVC discharge pipe complete all as specified and directed. 135 S&F in repairs Vitreous China Wash Down Water Closet Pan (pedestal pattern) complete, white/ coloured including seat and cover, trap, including connection to drain (or outgoing pipe), and to flushing pipe, anti-syphonage pipe, etc. etc.complete including all joints and making good to floors complete all as specified and directed. 136 S&F in repair sheet glassshelf assembly consisting of 5.5 mm thick sheet galss shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed. 137 S&F in repairs 10 litres capacity low level PVC valveless syphonic action typeflushing cistern with inlet ball valve, float and handle including brackets complete all as specified and directed. 138 S&F in repairs 100 mm dia Chromium plated shower rosewith 125mm long CP arms, with or without swivel joints, including fixing complete to steel pipe or union complete all as specified and directed. 139 S&F in repirs 600mmx450mm size of specified thickness looking mirror, bevelled edge of selected quality glass with aluminium frame made of channel around, mounted on 6mm thick commercial ply or AC building board, fitted to wooden plug with chromiumplated brass screws and cup washers complete all as specified and directed. 140 S&F in repairs Towel Rail 20mm dia brass chromium plated 600mm long between flangestype D,with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms)complete all as specified and as directed. 141 S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm longcomplete all as specified and directed. 142 S&F in repairs chromium plated steel soap dish not less than 1mm thickness fixed with chromium plated steel screws and PVC gutties complete all as specified and directed. 143 S&F in repairs 15mm bore chromium plated Wall mixer wall mounted type 3 in-1 for mixing hot and cold water screwed down for pipe with provision of overhead shower complete with 115 mm long bend pipe on upper side,connecting legsand wall flange complete all as per manufacturers instruction and as directed. 144 S&F in repairs 15mm bore chromium plated Wall mixer wall mounted for mixing hot and cold water screwed down for pipe with provision of overhead shower complete with 115 mm long bend pipe on upper side,connecting legsand wall flange for WHB,andkitchen sinks complete all as per manufacturers instruction and as directed. 145 Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed. 146 M&L for point wiring with PVC insulated but unsheathed single core FRLSH multistranded copper conductor cable IS-694 markedof size 1.5 Sqmm (nominal area) in and including 20mm dia non metallic rigid PVC conduit with all accessories if require such as bends,reducers, spacers, saddles, junction boxes bakelite sheets, wooden rectangular boards / round blocks(for housing lamp holders and light fittings etc) and existing mild steel pressed / cast iron sunken boxes of suitable size for mounting switches / bell pushes / sockets, fan regulator etc covered with new 3 mm thick laminated bakelite sheet top cover including continuous earth wire cable of size 1.5 Sqmm unsheated stranded copper conductor with green PVC FRLSH insulation connected to common earth dolly complete all as specified and directed for one light/fan/Bell Pointcontrolled by one single pole one way switch.Note:- Cutting chases for conduits and sinking boxes and making good to walls, floors etc, in case of recessed and concealed conduit wiring are included in item of taking down point wiring carefully. 147 ditto all as per item No 146 above but for one socket outlet on the sameboard controlled by one single pole one way switch 148 ditto all as per item No 146 above but for one 5 amps socket outlet independentcontrolled by one single pole 5 Amp switch. 149 M&L for point wiring with PVC insulated but unsheathed single core FRLSH multistranded copper conductor cable IS-694 markedof size 2.5 Sqmm (nominal area) in and including 20mm dia non metallic rigid PVC conduit with all accessories if require such as bends,reducers, spacers, saddles, junction boxes bakelite sheets, wooden rectangular boards / round blocks(for housing lamp holders and light fittings etc) and existing mild steel pressed / cast iron sunken boxes of suitable size for mounting switches / bell pushes / sockets, fan regulator etc covered with new 3 mm thick laminated bakelite sheet top cover including continuous earth wire cable of size 2.5 Sqmm unsheated stranded copper conductor with green PVC FRLSH insulation connected to common earth dolly complete all as specified and directed for the followings :- (a) one three pin 15 Amps switch socket out let on the independentboard controlled by one single pole one way switch.Note:- Cutting chases for conduits and sinking boxes and making good to walls, floors etc, in case of recessed and concealed conduit wiring are included in item of taking down point wiring carefully. 150 S & F Modular Switch one way6 A, 1 module complete all as specified anddirected. Make - Precision/Anchor/Havells/Legrand 151 S & F Modular Switch one way16 A, 1 module complete all as specified anddirected. Make - Precision/Anchor/Havells/Legrand 152 S & F Modular Socket, 6A - 2/3 pin combined 2 module complete all as specified anddirected. Make - Precision/Anchor/Havells/Legrand 153 S & F Modular Socket, 6A/16A - 2/3 pin combined 2 module complete all as specified anddirected. Make - Precision/Anchor/Havells/Legrand 154 S & F Modular white cover plate including GI box inner, 3 module complete all as specified & directed. Make : Precision/Anchor/Havells/Legrand 155 S & F Modular white cover plate including GI box inner, 4 modulecomplete all as specified & directed. Make : Precision/Anchor/Havells/Legrand 156 S & F Modular white cover plate including GI box inner, 8 module complete all as specified &directed. Make : Precision/Anchor/Havells/Legrand 157 S & F Modular step type regulator,120 W - 2 module complete all as specified anddirected. Make - Precision/Anchor/Havells/Legrand 158 S&F5/6 Amp Switch piano flush type single pole one way ISI Marked complete all as specified and directed. 159 S&F15/16 Amp Switch piano flush type single pole one way ISI Marked complete all as specified and directed. 160 S&F5/6 AmpSocket outlet 2 in1, 3 pin flush typeISI marked complete all as specified and directed. 161 S&F15/16 AmpSocket outlet 2 in 1, 3 pin flush typeISI marked complete all as specified and directed. 162 S&F5/6 Amp bell pushflush typeISI marked complete all as specified and directed. 163 S&F5/6 Amp modular bell pushflush type, one module,ISI marked complete all as specified and directed. 164 S&F Lamp holder PVC/Polycarbonate,isolated with back plate suitable for batten fittings ISI marked complete all as specified and directed. including 10W LED Bulb omplete all as specified and directed. 165 S&F Ceiling Roses Ceiling rose, 3 phase/PVC/polycarbonate, isolated bodyomplete all as specified and directed. 166 S&F Buzzer, Ding Dong AC. 230 Volts, single pole complete all as specified and directed. 167 S&F bell, Ding Dong AC. 230 Volts, single pole complete all as specified and directed. 168 S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as required complete all as specified and directed. 169 S&F 300mm sweep Exhaust Fan, steel body AC single Phase. 230Vwith blades and frame and louvers with Copper windingcomplete all as specified and directed. 170 S&F 300mm sweep Exhaust Fan, sturdy Engineering plastic body with louvers AC single Phase. 230Vwith blades and frame and louvers with Copper windingcomplete all as specified and directed. 171 S&F LED tube light fitting 1 X 18 Wdecorative ultra slim linear LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient230V,complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size. Cat Part No. LHEXBLP7UN1W018 of Make - Havells or equivalent as specified in Appendix B of Particular Specfications,complete all as specified and directed.. 172 S&F LED Mirror light 7/9/18 Watt 2 ft adjustable type enegy saving curve type t as specified in Appendix B of Particular Specfications,complete all as specified and directed. 173 S&F LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impactand corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. complete all as specified and directed. 174 S&F LED tube light fitting20 Watt 4 feet long decorative ultra slim linear LED lighting three colour CCT Change LED Batten Which can change the Colour of batten FROM WHARM WHITE TO natural white to cool whitewhite the help of a simple toggle switch, fixture with extruded polycarbonate,environmental friendly, energy efficient230V,complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed. 175 S&F sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series pre-wired TPN DBs, 415 Volts 200Amps rated bus bar,Neutral link,Earth bar andDin rail,4 ways dust and vermin proof suitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified. 176 S&F sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series pre-wired SPN DBs, 240 Volts 200 Amps rated bus bar,Neutral link,Earth bar andDin rail,8 ways dust and vermin proof suitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified. 177 S&F Moulded Case Circuit Breaker (MCCB) Four Poles (FP) current carrying capacity 63Amp, 415 Volts,breaking capacity 16 KA with adjustable thermal and magnetic settings, completeall as specified and directed. 178 S&F Moulded Case Circuit Breaker (MCCB) Four Poles (FP) current carrying capacity 100Amp, 415 Volts,breaking capacity 16 KA with adjustable thermal and magnetic settings, completeall as specified and directed. 179 S&F Miniature Circuit Breaker (MCB) Single Pole (SP) current carrying capacity 6 to 32 Amp, 240V, breaking capacity 10 KA, typeB curve in the MCB DB Complete with connection testing and commissioning complete all as specified and directed. 180 S&F Miniature Circuit Breaker (MCB) Single Pole(SP) current carrying capacity 40Amp, 240V, breaking capacity 10 KA, typeB curve in the MCB DB Complete with connection testing and commissioning complete all as specified and directed. 181 S&F Miniature Circuit Breaker (MCB) Single Pole and Neutral(SPN) current carrying capacity 32 Amp, 240V, breaking capacity 10 KA, typeC curve in the MCB DB Complete with connection testing and commissioning complete all as specified and directed. 182 S&F Miniature Circuit Breaker (MCB) Single Pole and Neutral(SPN) current carrying capacity 40 to 63Amp, 240V, breaking capacity 10 KA, typeC curve in the MCB DB Complete with connection testing and commissioning complete all as specified and directed. 183 S&F Single Pole two Pin and Earth Plug and Socket including one single pole MCB 20 Amp fixed in sheet Metal enclosures complete all as specified and directed. 184 M&L for submain wiring with two single core PVC insulated FRLSH cable with Copper conductor unsheathed cable of size4.0Sqmm drawn through in and including 25mm dia non metallic rigid PVC conduit with all accessories including one 4.0Sqmm PVC insulated FRLSH cable with Copper conductor unsheathed cablesingle core for continuous earthing complete all as specified and directed. ( Note : Two run of single core PVC insulated cable with Copper conductor unsheathed cable of size 4.0Sqmm and one run of 4.0Sqmm PVC insulated copper conductor single core (2x4.0Sqmm+1x4.0Sqmm earth wire) and one run of PVC conduit shall be measured as single run) 185 M&L for submain wiring with two single core PVC insulated FRLSH cable with Copper conductor unsheathed cable of size6.0Sqmm drawn through in and including 25mm dia non metallic rigid PVC conduit with all accessories including one 6.0Sqmm PVC insulated FRLSH cable with Copper conductor unsheathed cablesingle core for continuous earthing complete all as specified and directed. ( Note : Two run of single core PVC insulated cable with Copper conductor unsheathed cable of size 6.0Sqmm and one run of 6.0Sqmm PVC insulated copper conductor single core (2x6.0Sqmm+1x6.0Sqmm earth wire) and one run of PVC conduit shall be measured as single run) 186 Supply, lay, test, joint and commission LTXLPE insulated , screened, PVC bedded, galvanised steel strip or wire armoured electric powercable heavy duty with aluminium conductor of sizecross sectional area 25Sqmm x 4 core, 1100 Volts grade (1.1 KV earthed system); laid in trenches/under floor/through ducts, on Hill / fixed on polecomplete all as specified and directed. Note:- Excavation & Earth work, sand cushioning, cable protection cover, pipe shall be measured and paid separately under respective items of BoQ. 187 Supply, lay, test, joint and commission LTXLPE insulated , screened, PVC bedded, galvanised steel strip or wire armoured electric powercable heavy duty with aluminium conductor of sizecross sectional area 16Sqmm x 4 core, 1100 Volts grade (1.1 KV earthed system); laid in trenches/under floor/through ducts, on Hill / fixed on polecomplete all as specified and directed. Note:- Excavation & Earth work, sand cushioning, cable protection cover, pipe shall be measured and paid separately under respective items of BoQ. 188 Supply and lay 40mm bore galvanised pipe light grade of ISI marked for passing of cable fixed to poles/walls/laid under floor/ laid in trenches ascable protection complete with and including fittings as required compete all as specified and directed.Note:- Excavation & Earth work, sand cushioning, cable protection cover, pipe and joint shall be measured and paid separately under respective items of BoQ. 189 M&L for Sand cushioning using sand suitable for plaster works to under ground cable in trenches/existing cable trenches/ductsin layers of 8 cm deep before laying the cable and 15 cm deep punned to 10cm after laying and stretching the cable complete all as specified and directed. Note : 18 cm punned thickness shall be measured and paid. 190 Supply and lay cable protection cover withBricks; common burnt clay building bricks, sub-class ‘B’ designation 75, (size 23cmx11.5cmx7.5cm) putting accross the cable with width of protection cover equal to length of brick, abutting to each other for cable protection complete all as specified and directed. 191 M&L for Earthing complete with Galvanised Iron earth plate electrode 60cmx60cmx6mm thick buried directly in ground vertically at (Earth pit not less than 2.25m deep below ground level) a depth not less than 2.25m below normal ground level with top edge of earth plate at depth not less than 1.5m below normal ground level surrounded from all sides by 15cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode connection by using 4mm diagalvanised earth wire by means of bolts, nuts, check nuts and washers of galvanized iron and protected by 15mm bore GI pipe light gradeconnected to main switch board or main control board and20mm bore GI pipe light grade for watering and including funnel, wire mesh, 80mm thick pre-cast RCC (1:2:4) type B-1 cover reinforced with hard drawn steel wire fabric weighing not less than 4Kg/Sqm in lieu of CI cover, PCC (1:2:4)type B-1 pit/chamber including all necessary excavation: and earth work, form work, disposal of surplus soil to a distance not exceeding 50m all as specified and al shown in Electrical Plate No.3 of MES Standard Schedule of Rates 2009 Part-Icomplete all as specified and directed.Note:- (i) The unit rate shall deemed to include for Test point, PCC pit, 4mm dia GI earth wirefrom top of the earth plate up to 7.5m above ground level. In case 15mm bore GIprotection pipe required is less than 7.5m, no price adjustment shall be made. (ii) PCC pit shall be provided at least 500mm away from the earth pit and not just on the earth pit and extra cost of additional length of water pipes and fittings, junctions, elbow etc shall be deemed to be included in the unit rate.(iii) On testing after completion if the desired earth resistance is not obtained the earthing will be redone at no extra cost.
