Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Taking down shutters of any description exc 1 sqm and n exc 2 sqm each and refixing in same opening copmplete all as specified and directed. |
| 2 | S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aparture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 3 | S&F 4 mm thick sheet glass ordinary quality and glazing complete in square nexc 0.50 sqm in each pane complete all as specified and directed. |
| 4 | S&F 4 mm thick sheet glass ordinary quality and glazing complete in square exc 0.50 sqm in each pane complete all as specified and directed. |
| 5 | S&F in repair Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aparture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 6 | M&L Silicon gun paste around windows of any type/ size and at any height of the building by using scaffolding complete all as specified and as directed. |
| 7 | Taking down chowkats or frames including shutter (without taking off shutters from the frame) area n exc. 1.5 Sqm each complete all as specified and directed. |
| 8 | All as per item No. 07 above but exc 1.50 Sqm and n.exc 4 Sqm each complete all as specified and directed. |
| 9 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixedportions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and directed. |
| 10 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws,star lock, rubber beading all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 11 | S&F Aluminium powder coated grill (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC15) of approved design/pattern(DG 104), with approved standard section and fixed to existing window frame with CP brass/stainless steel screw not less than 50mm and @ 200mm c/c, incl cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section (28mm x 19mm x 2mm thick) around the opening, complete all as specified and directed. |
| 12 | Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc copmplete all as specified and directed. |
| 13 | S&F GI chicken wiremesh 0.63mm dia of wire and 19mm aperture fixed to RCC and brick/block masonry all as specified and directed. |
| 14 | M&L 15 mm thick ready mix polymer modified plaster on external surfaces on brick or concrete surfaces finished even and smooth complete all as specified and directed. |
| 15 | M&L 10 mm thickready mix polymer modified plaster on internal surfaces of brick or concrete surfaces finished even and smooth complete all as specified and directed. |
| 16 | M&L 5 mm thick ready mix polymer modified plaster on ceiling surfaces finished even and smooth complete all as specified and directed. |
| 17 | M&L Providing and applying wall care putty of 1.5mm thickness over plastered surface to prepare the surface even and smooth copmplete all as specified and directed. |
| 18 | Supply only integralwater proofing compound complete all as specified and directed. |
| 19 | M/L Preparation of old/new plastered surfaces and applying two coats of OBD on ceilings including complete removal of existing treatment all as specified and directed. |
| 20 | M&L for complete removal of existing treatment from wall all as specified and directed. |
| 21 | M & L for preparation of old/newly plastered surfaces and applying two coats of plastic emulsion paint on wall surfaces complete all as specified and directed. |
| 22 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives@ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new/old surfaces including 1.5mm thick external wall care putty complete all as specified. |
| 23 | M&L Granite slab 18-20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over & including 20mm thickscreed/backing coat in CM 1:4 to match incl cutting, polishing complete all as specified and as directed. |
| 24 | S&F Coloured Non Skid ceramic tiles7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & incl20mm thick screed in CM(1:6) incl dismantling old tiles complete all as specified and directed. |
| 25 | S&F Coloured Glazed ceramic tiles in vertical surfaces300x450x7mm thickset and jointed in neat cement slurry and pointed in white or coloured cement to match over & incl 15mm thick backing coat in CM(1:4) on fair face of brick or concrete surface iincl dismantling old tiles complete all as specified and directed. |
| 26 | Supplying and fixing of 20mm bore Tubes, \"medium grade galvanised, with all fitting; laid in trenches or fixed to walls with hooks, ceiling or laid on floor including taking down old u/s pipe complete all as specified and directed by Engineer in Charge. |
| 27 | Supplying and fixing of 25mm bore Tubes, \"medium grade galvanised, with all fitting; laid in trenches or fixed to walls with hooks, ceiling or laid on floor including taking down u/s old pipe complete all as specified and directed by Engineer in Charge. |
| 28 | M&L in repairs CI Floor trap long neck 100 mm dia, with stainless steel grating including jointing to waste pipe fixed in cement concrete type B1, 1:2:4 matching to the existing finishing complete all asspecified and directed . |
| 29 | S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 30 | Supply and fix 75mm dia PVC (SWR) pipe single socket in any length with rubber ring joint fixed to wall or laid in trenches complete all as specified and as directed. |
| 31 | 40mm bore Low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq. Cm complete all as specified and directed. |
| 32 | M&L Boring holes through stone/tile lining for pipes, etc. n exc 50 mm dia and making good complete all as specified and directed. |
| 33 | S&F in repair 15mm bib taps, fancy type chromium platedwith crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 34 | S&F in repairs 15 mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed. |
| 35 | S&F in repair 15mm angle cock with flange cast copper alloy, chorminium plated, fancy type, screwed both ends for iron pipe or for union complete all as specified and directed. |
| 36 | S&F in repair Wash hand basin flat back 550x400mm vitreous china (white) with cantilever CI/Angle iron brackets embedded in concrete block including Brass chromium plated waste coupling 32mm bore, Waste pipe PVC 32mm bore, complete all as specified and directed. |
| 37 | S&F in repairs vitreous china wash down water closet pan padestel pattern white including connection pipe to union of flushing cistern, seat and cover for pedestal pan, inlet and overflow pipes,connecting only to flushing cistern anti-syphonage pipe with PVC flush pipe of 32mm diawith mild steel chromoum plated hinging and \"P\" or \"S\" trap device complete all as specified and directed. |
| 38 | S&F in repairs, 10 litre capacity PVC, syphonic action type, flushing cistern, low level, white, with inlet, ball valve,pvc flush pipe, float and handle incl brackets and waste pipe complete all as specified and directed. |
| 39 | M&L for preparation of old surfaces of steel or iron surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.. |
| 40 | S&F in repair waste coupling 32 mmbrass chromium plated for glazed ware sinks, basins etc.with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed |
| 41 | S&F in repair PVC connections 15 mm size with brass nuts both side of length 450 mm complete all as specified and directed . |
| 42 | S&F in repairbrass chromium plated towel rail 20mm dia, D type, 60cm long between flanges fixed with CP brass screwsincluding wooden/plastic beads complete all as specified and directed. |
| 43 | S&F 1000 ltr capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in positionincl float valve of 20mm diaand dismantling the old U/S tank all as specified and as directed. |
| 44 | S&F in repair 20mm bore gate valve cast copper alloy with handle screwed both ends for GI out let/inlet pipe or for union including threading to existing pipes on both ends complete all as specified and directed. |
| 45 | Complete removal of existing water proofing treatment of any description and in any position including PCC padding any thickness and cleaning, wire brushing, watering & removal of debris outside MOD complete all as specified and directed..NOTE :-Unit rate quoted shall also include for removal of PVC water storage tank wherever existing carefully and refixing at the same or other position after completion of roof repair work |
| 46 | M&L Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) complete all as specified and directed. |
| 47 | Roughening surfaces of old concrete floors by picking, sweeping clean and washing down with waters to remove dusts etc. complete all as specified and directed. |
| 48 | Brushing neat cement slurry with 3kg/sqm all as specified and directed. |
| 49 | M&L PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate as in concrete padding laid to required slope incl finishing the concrete surface fair and even without using extra cement complete all as specified and as directed. |
| 50 | M & L for 10 mm thick screed bed or bedding layer of mortar in cement mortar (1:4) for laying roof finish as padding finished with WPCas per manufacturer instructions, complete all as specified and directed NOTE :-Integral WPC shall be measured and paid separately. |
| 51 | Apply oil bound bitumen primer @ 0.40 Litre / Sqm manufactured by the same agency as that of APP with density of 0.87 to 0.89 Kg / Litre at 25 degree Celsius on the prepared dry roof surface complete all as specified and directed. |
| 52 | M&L APP polymeric membrane min weighting 3.5kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than 150 gms/sqm) laid on primed surfaces by torch application method all as specified and directed. |
| 53 | M&L for preparation of new surfaces of any description not otherwise described over 10cm width or girth and applying one coats of solar reflective aluminium paint @ 0.10 kg/sqm of membrane surfaces all as specified and directed. |
| 54 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for all as specified and directed. |
| 55 | M&L Cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, all as specified and directed. |
| 56 | Providing precast cement concrete cover slabs type B1 1:2:4 (20mm graded aggregate) set in CM 1:6 (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces complete with joints to match all as specified and directed. |
| 57 | M&L TMT bar10mm dia & over deformed & twisted bars cut to length ,bent to shape required incl cranking , bending , hooking, for lintel and binding with MS wire not less than 0.9 mm dia or securing with clips complete all as specified and as directed. |
| 58 | S&F projector clamps on celing with necessary arrangement like fastner/screws etc incl making good to the existing surface all as directed by Engineer In charge, |
| 59 | M&L for Machine cut Sadrahalli stone slab of 18 - 20mm thick(1 st Quality) as in floor, riser of steps, skirting, dado and pillar laid over and including 20 mm thick screed bed in CM (1:4) jointed & pointed in grey cement slurry mixed with pigment to match the shade of the slab and including rubbing, polishing etc complete all as specified and directed. |
| 60 | M&L for 25 mm thick PCC 1:2:4 type B-1 using20mm graded stone aggregate as in flooring,finishedeven and smooth without using extra cement complete all as specified and as directed. |
| 61 | M&L Rendering 5mm thick in CM (1:3) onconcrete surfaces ceiling & finished even and smooth without using extra cement complete all as specified and directed. |
| 62 | M&L for rendering 10 mm thickin CM 1:6 on faces of brick work/ stone wall / concrete surfaces of wall finished even and smooth without using extra cement complete all as specified and as directed. |
| 63 | M&L Two coats of white wash on new/old plastered surfaces of ceilings including preparation complete all as specified and directed. |
| 64 | M & L for preparation of newly or untreated plastered surface/ putty applied surfaces of wall and applying two coats ofoil bound distemper (OBD) over a coat of primer complete all as specified and directed. |
| 65 | M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bed in cm 1:4 including dismalting of old tiles all as specified & directed. |
| 66 | S& F in repairs 32 mm dia concussive push button taps of cast copper alloy, chromium plated screwed for iron pipe and fixed all as specified and directed. |
| 67 | Material and labourfor servicing/ easing of steel windows of size not exceeding 2 Sqm each including cleaning, scrapping, hacking, oiling, necessary welding, replacing broken hinges, handles ,stay etc and making good disturbed portion, painting etc, complete all as specified as directed . |
| 68 | S&F 4 mm thick sheet glass ordinary quality and glazing complete in square n exc 0.50sqm each with oil putty incl hacking out old/broken glass complete all as specified and directed. |
| 69 | Taking down old u/s aluminium/copper point wiring & including hard wood battens, surface conduit and board/ blocks etc or through conduits for light, socket or power point, fan point complete and making good the disturbed plaster surfaces of wall, floor, ceilingand painting 2 coat of white wash/distamber to match the existing surface, complete all as specified and directed. |
| 70 | M & L for Point wiring with PVC insulated FRLS 1.5 sq mm multi stranded copper conductor cable 1100 Volts grade drawn into and including rigid non mettalic PVC conduit/casing caping medium grade not less than 19/20 mm ( ISI marked ) with all fitting and fixing accessories including sunk in pressed steel chromium plated terminal boxes, concealed in wall/surface/roofs/floor/ceiling etc as per site requirement and making & matching the existing surface ) white bakelite sheet cover for mounting switches, Sockets, Fan regulators etc or modular cover plate with frame including sunken boxes suitableto fix modular cover plate with frame , concealed in wall and 1.5 sq mm multi stranded copper conductor cable as continuous earth wire drawn with wiring and connected to common earth dolly forone light point controlled by one wayswitch complete all as specified and directed. Make of wire: Polycab/Plaza/HavellsNote:Blanking plate,Modular cover plate ,Switches, sockets outlets, Light fittngs, fans, bells & regulators shall be measured and paid for separetely). |
| 71 | All as per item No. 70 here in before but for one ceiling fan point controlled by one wayswitch. |
| 72 | All as per item No. 70 here in before but for one 3 pin socket out let 5 Ampon the same board |
| 73 | All as per item No. 70 here in before but for one switch socket outlet 3 pin 5 Amps on independent board |
| 74 | All as per Sl No. 70 above but Wiring with 4 Sqmm copper multistranded unsheathed cable and 4 Sqmm copper cable for earth continuity conductor controlled by one 15A switch socket independently complete all as specified and directed. |
| 75 | Supply and Fixmodular switch1 way 6 Amp.1 module, complete all as specified and directed.Make : Legrand/ Crabtree/ Anchor/Indoasian |
| 76 | Supply and Fixmodular switch2 way 6 Amp.1 module, complete all as specified and directed.Make : Legrand/ Crabtree/ Anchor /Indoasian |
| 77 | Supply and Fixmodular Socket, 6A - 2/3 pin combined 2 module, complete all as specified and directed.Make : Legrand/ Crabtree/ Anchor/Indoasian |
| 78 | Supply and Fixmodular switch1 way 16 Amp.1 module, complete all as specified and directed. Make :Legrand/ Crabtree/ Anchor /Indoasian |
| 79 | Supply and Fix modular Socket, 16A - 3/5 pin combined 2 module, complete all as specified and directed. Make : Legrand/ Crabtree/ Anchor/Indoasian |
| 80 | Supply and fix White cover plate with frame,1 module |
| 81 | Supply and fix White cover plate with frame,2 module |
| 82 | Supply and fix White cover plate with frame,3 module |
| 83 | Supply and fix White cover plate with frame,4 module |
| 84 | Supply and fix White cover plate with frame,6 module |
| 85 | Supply and fix White cover plate with frame,8 module |
| 86 | Supply and fix White cover plate with frame,12 module |
| 87 | S & F in repair Modular fan regulator 120W, 2 Module for ceiling fan complete all as specified and directedMake : Legrand/ Crabtree/ Anchor |
| 88 | Supply and fix in repairs of ceiling rose, 3 phase/PVC/Polycarbonate isolated body with three terminals all as specified and as directed. |
| 89 | M&L for sub main wiring with PVC insulated unsheathed FRLS cable 1100 volts grade multi stranded copper conductor cable 2 runs of 4 Sqmm drawn through in and incl suitable size surface PVC casing caping/PVC Conduit and all accessories fixed to wall/floors along with 4 Sqmm PVC insulated unsheathed copper conductor multi stranded cable 1100V grade as earth continuity conductor and connected to common earth dolly including taking down existing sub main wiring of any size.Note: (a)2 runs of 4 Sqmm cable along with one run of 4 Sqmm cable for earth conductor shall be measured as one lengthMake:- Havells/ Polycab/ Plaza. |
| 90 | S&F in replacementfactory madepowder coated distribution board TPN, 4 way double doorMCBDB includingbus bar, Neutral bar, standard DIN rail, earth bar complete including taking down unserviceable DBcomplete all as directedMake : Indoasian/ Havells/ Legrand. |
| 91 | Supply and fix TPN, MCB 63 Amp, 240 v, 50 Hz ACsuitable for ‘C’ curve, 10 KA breaking capacitycomplete conforming to IS 8828 of 1996, all as specified Make : Legrand/ L&T/ Indo Asian |
| 92 | Supply and Fixing in repairs of 4 feet surface mounted batten type luminaire , lumen output of 2000 lumens, high efficiency long life LED package in integral module with lumen efficacy of >100 lm/w, viewing angle not less than 120° to ensure better uniformity with an operating voltage range from 140V-270V. The luminaire shall have a white extrusion housing with a poly carbonate diffuser to provide uniform light and sleek design with width not more than 22 mm. The luminaire shall have a CRI >80, Color temperature 6500K, THD <10% and PF >0.95,SDCM<5, IP20, IK02, Operating Temperature: -10 TO + 45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-55 HZ. The luminaire shall have flicker content<5% and shall have high and low cut off with auto restart feature.Driver Safety requirement stds: IS 15885-2-13. The luminaire shall be EMI/ EMC compliant and shall have a internal surge protection of 4 KV. The luminaire shall have Class-1 Electrical insulation, Class-B serviceability .The luminaire and driver shall be BIS approved, complete all as specified and directed.Make : Philips/ Bajaj / CG/Havells. |
| 93 | Supply and Fixing in repairs of 2 feet surface mounted batten type luminaire , lumen output of 1000 lumens, high efficiency long life LED package in integral module with lumen efficacy of >100 lm/w, viewing angle not less than 120° to ensure better uniformity with an operating voltage range from 140V-270V. The luminaire shall have a white extrusion housing with a poly carbonate diffuser to provide uniform light and sleek design with width not more than 22 mm. The luminaire shall have a CRI >80, Color temperature 6500K, THD <10% and PF >0.95,SDCM<5, IP20, IK02, Operating Temperature: -10 TO + 45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-55 HZ. The luminaire shall have flicker content<5% and shall have high and low cut off with auto restart feature.Driver Safety requirement stds: IS 15885-2-13. The luminaire shall be EMI/ EMC compliant and shall have a internal surge protection of 4 KV. The luminaire shall have Class-1 Electrical insulation, Class-B serviceability .The luminaire and driver shall be BIS approved, complete all as specified and directed.Make : Philips/ Bajaj / CG/Havells. |
| 94 | S&F in repairs 35/36 W( WH) LED recess type 2x2 ft luminaire with classic design & glare free soft illumination. housing with white high reflection powder coated (RAL9016) CRCA sheet. Glare free, Opal diffuser for symmetrical light distribution fixed in separate CRCA sheet frame held in with housing by screws for easy maintenance. High efficiency long life LED package in integral module with lumen efficacy of >100 lm/w, viewing angle of 100° to ensure better uniformity. Powered by an independent Isolated, SELF Output electronic LED driver (SMPS based constant current supply) efficiency of 85% with built-in Surge protection 3Kv. System Lumen Output of 3000 lumens.Make : Philips/ Bajaj/CG/Havells. |
| 95 | Taking down the existing ceiling fan of any size, sealing cable end, dismantling the blades with accessories, removing fan and blades and deposit to store yard for re-use complete and refixing the same after completion of building repair work including cleaning the total surface of fan and new greasing in the bearings complete all as specified and as directed. |
| 96 | Supply and fixing in replacement of unserviceableCeiling fan 1200mm sweep, energy efficient ISI marked withstar rating 230 Volts AC 50 Hz, single phase including provision of fixing arrangement, nut and bolt andflexible copper cable 3 core of size 1.5 sqmm not less than 0.5 m long complete complete all as specified and directed. Make : Havells/ Bajaj/ Orient |
| 97 | Supply and fixing LED flood light 100 watt 230 V AC outdoor type including necessary bracket with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp including taking down of old unserviceable fitting of any capacity. Make : Halonix/Philips/CG/Bajaj |
| 98 | Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for laying of cable, foundation etc, and getting out in soft /loose soilall as specified and directed. |
| 99 | Returning filling in including spreading, leveling Watering and well ramming in layers not exceeding 25cm all as specified and directed. |
| 100 | Removing excavated surplus soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all as specified and directed. |
| 101 | Material and Labour for Spreading ribbed soil in trenches as in cable cushioning all as per IS 1255-1983and as directed. Note :- Excavated approved soil shall be ribbed by using sieve to separate composite particles etc as per IS and refiiling in trenches before laying of cable 8 CM and 15 CM after laying of cable. This is then gently punned down to a depth of 10 cm above the top of upper most cable(ii) For the purpose of measurement only punned thickness shall be considered for paymet. |
| 102 | Material and labour for Cutting existing road/PCC/Drain for laying of GI or any type of pipe including necessary earthwork, excavation exc 600mm depth but not exc 1mtr depth, 800 mm wide including making good existing surface with 150 mm thick PCC 1:2:4 type B1 using 20mm graded stone aggregate, complete all as specified and directed. Note :-The tenderer shall take into consideration for following points while quoting rate for this item andthe unit rate is deemed to be inclusive for :-(i) Earth work and excavation in any type of soil(ii) Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick ,complete all as specified and as directed.(iii) Removing excavated material to out side MD land.(iv)Laying of any type/any bore of pipe in trenches including taking down. Supply of pipe shall be measured and paid separately(v)150 mm thickPCC 1:2:4 type B1 using 20mm graded stone aggregate as inroad to make good existing disturbed surfaces. |
| 103 | Material and Labour for well burnt subclass ‘B’ bricks as mechanicalprotection forunder ground LT electric cables laidalong with length of the bricks equal to the width of the trench complete all as speified and directed . |
| 104 | Material and labour forBoring of holes under road, pavement hard standings by trenchless technology using ultra sound technique and necessary machine including HDPE pipes upto 100 mm dia suitable for 0.4 Mpa working pressure, complete all as specified and directed. |
| 105 | Supply and Fixing GI tubing light grade 50 mm dia fixed on walls/pole/ laid in trenches as protection pipe for under ground cable including provisioning of specials and clamps etc complete all as speified and directed. |
| 106 | Material and labour in repair for 4 core 6 Sqmm XLPE insulated heavy duty electric cable with aluminium multi stranded conductor 1100 volts grade served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall sheathed laying in trenches/cable ducts, fixed to wall/pole, complete all as specified and directed. Make : Havells/ Polycab/ RPG Asian |
| 107 | Material and labour in repair for 3.5 core 25 Sqmm XLPE insulated heavy duty electric cable with aluminium multi stranded conductor 1100 volts grade served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall sheathed laying in trenches/cable ducts, fixed to wall/pole, complete all as specified and directed. Make : Havells/ Polycab/ RPG Asian |
| 108 | M & L for Point wiring with PVC insulated FRLS 1.5 sq mm multi stranded copper conductor cable 1100 Volts grade drawn into and including rigid non mettalic PVC conduit/casing caping medium grade not less than 19/20 mm ( ISI marked ) with all fitting and fixing accessories including sunk in pressed steel chromium plated terminal boxes, concealed in wall/surface/roofs/floor/ceiling etc as per site requirement and making & matching the existing surface ) white bakelite sheet cover for mounting switches, Sockets, Fan regulators etc or modular cover plate with frame including sunken boxes suitableto fix modular cover plate with frame , concealed in wall and 1.5 sq mm multi stranded copper conductor cable as continuous earth wire drawn with wiring and connected to common earth dolly forone Exhaust/wall fan point controlled by one wayswitch complete all as specified and directed. Make of wire: Polycab/Plaza/HavellsNote:Blanking plate,Modular cover plate ,Switches, sockets outlets, Light fittngs, fans, bells & regulators shall be measured and paid for separetely). |
| 109 | All as per item No. 108 here in before but for one bell point controlled by one wayswitch. |
| 110 | All as per item No. 108 here in before but for one light point controlled by two Nos way switch . |
| 111 | Supply and Fixmodular switch2 way 6 Amp.1 module, complete all as specified and directed.Make : Legrand/ Crabtree/ Anchor /Indoasian |
| 112 | Supply and Fixmodular switchbell push .1 module, complete all as specified and directed.Make : Legrand/ Crabtree/ Anchor /Indoasian |
| 113 | Taking down the existing exhaust fan of any size, sealing cable end, dismantling the blades with accessories, removing fan and blades and deposit to store yard for re-use complete and refixing the same after completion of building repair work including cleaning the total surface of fan and new greasing in the bearings complete all as specified and as directed. |
| 114 | Supply and fixingExhaust fan 300 mm sweep 230/ 240 volt AC single phase Metal body 1400 RPM including necessary nut, bolts / screws all specified and directed. Make-Havells /Bajaj/ Crompton Greaves |
| 115 | M&L for cutting of hole through cement concrete wall including providing, fixing and removing shoring,cleaning,internal plastering and removing surplus hard core,rubbish not exceeding 50 mtrs including fixing of exhaust fan of size 250-300 mm all as specified and as directed. |
| 116 | Supply and fix in repairs LED decorative post top lantern fitting 40W, 230V AC with IP 65 protection and resistant to impact and corrosion with necessary electrical connection completeall as specified as directed. Make: Bajaj / Philips/Halonix/ CG |
| 117 | M&L for sub main wiring with PVC insulated unsheathed FRLS cable 1100 volts grade multi stranded copper conductor cable 2 runs of 6 Sqmm drawn through in and incl suitable size surface PVC casing caping/PVC Conduit and all accessories fixed to wall/floors along with 6 Sqmm PVC insulated unsheathed copper conductor multi stranded cable 1100V grade as earth continuity conductor and connected to common earth dolly including taking down existing sub main wiring of any size complete all as specified and directed.Note: (a)2 runs of 6 Sqmm cable along with one run of 6 Sqmm cable for earth conductor shall be measured as one lengthMake:- Havells/ Polycab/ Plaza. |
| 118 | S&F in replacement factory madepowder coated distribution board SPN 4 way double door,includingbus bar, Neutral bar, standard DIN rail, earth bar complete including taking down unserviceable DBall as specified and conforming to IS: 8623, all as specified and directed. Make : Legrand/ L&T/ Indo Asian |
| 119 | S & F MCB in repair and replacement ofSPN 240 volts 16 to 32 Amps ‘C’ curve, 10 KAcomplete including taking down unserviceable fitting complete all as specified and as directed .Make : Legrand/ L&T/ Indo Asian |
| 120 | S & F in repair and replacement of MCB single pole 240 volts 6 to 32 Amps ‘C’ curve, 10 KA complete including taking down unserviceable fitting complete all as specified and as directed .Make : Legrand/ L&T/ Indo Asian |
| 121 | Supply and fix metal clad switch socket single pole and neutral enclosure withtwo pin and earth plug and socket complete with one single pole MCB 20A ‘C’ curve, 10 KA concealed in walls. Make : Legrand/ L&T/ Indo Asian |
| 122 | Supply and fixing in repair building security/ LED street light fitting 35/36 Watt, 230 V AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal, management in multiple optics complete, with IP 65/66 protection complete all as specified and directed. Make: Philips/Bajaj/CG |
| 123 | Supply and fix GI pipe 32 mm dia, medium grade for mounting bracket, bent to shape 1.5 meter length and fixing arrangement with two Nos ofclamps set, nut, bolts, washers, andincl taking down old unserviceable GI pipe complete all as specified and directed |
| 124 | Supply and fix in repair weather proof PVC junction box approved by CPRI for street light control box made out of not less than 2mm thick and size 250mm x 200 mm x 105mm (approx) complete with hinged door locking arrangement and consisting of 2 Nos of suitable size cable glands consisting of 01 No. panel mounted connector 4 pole 32A-1 No, MCB SP 6A 10KA-01No, including connecting up with the electrical connections and fixing with clamps etc complete and all as specified anddirected. |
| 125 | Supply and fixing exhaust fan with louvers, ball bearing. silent operation, steelbody and blades with fixing arrangements of size 250 mm sweep, Speed not less than 1000 rpm, 240V, Make Havells / Bajaj/CG/Usha. |
| 126 | Supply and fixing exhaust fan with louvers, ball bearing. silent operation, PVCbody and blades with fixing arrangements of size 250 mm sweep, Speed not less than 1000 rpm, 240V, Make Havells / Bajaj/CG/Usha. |
| 127 | M&L for cutting of hole through stone wall including providing, fixing and removing shoring,cleaning,internal plastering and removing surplus hard core,rubbish not exceeding 50 mtrs including fixing of exhaust fan of size 250-450 mm all as specified and as directed. |
| 128 | Supply & Fix Open well submersable pump of capacity 1HP, single phase 240Vincluding DOL starter and control wiring, complete all as specified & directed. |
| 129 | Supply and fixing PVC suction Hose pipe of size 32 mm dia complete all as specified and as directed. |
| 130 | Supplying, errecting and fixingas in repair GItubular swaged welded pole of height 5 m long suitable for 900 mmlightining Arrestercompletewith GI base plate with stand fixing over the roof, finial tapper plug cap, bolt, nut and washer etc. The pole is made suitable GI clamp weldedfor holding of lightening conductor insulator / post insulator with a distance of 600 mm from top to bottom with PCC (1:2:4) type B-1 using 20mm graded aggregate 750X750 X500 mm over the roof anchored with suitable size boltscomplete all as specified and directed . |
| 131 | Supply and fixing of copper earth continuity conductor or main earthing lead fixed to wall /roof top for lightning arrester /fixed to poles or any other indicated situation for loop earthing etc. as required of 20 mm x 3 mm thick, using porcelain clit/post insulators with screw / selfdril GIscrew with rubber washer , complete all as specified and directed. |
| 132 | Supply and fixing copper lightning arrester having 5 spikes of 10mm dia fixed over base plate of size 8.5 x 8.5 cm and 3mm thick and main base rod of 20mm dia and 915mm long fixed to copper strip including nuts,bolts & washersfor earth conductivity to ground complete all as specified and as directed. |
| 133 | Supply and fix in repairs LED bollard light 10 W of 600/605 mm height, metal support column pipe with base arrangement, pre wired with SPD and LED drivers, light output in warm white in colour complete all as specified and directed. Make : Halonix/Philips / Crompton. |
| 134 | M & L for Point wiring with PVC insulated FRLS 1.5 sq mm multi stranded copper conductor cable 1100 Volts grade drawn into and including rigid non mettalic PVC conduit/casing caping medium grade not less than 19/20 mm (ISI marked) with all fitting and fixing accessories including sunk in pressed steel chromium plated terminal boxes, concealed in wall/surface/roofs/floor/ceiling etc as per site requirement and making & matching the existing surface ) white bakelite sheet cover for mounting switches, Sockets, Fan regulators etc or modular cover plate with frame including sunken boxes suitableto fix modular cover plate with frame , concealed in wall and 1.5 sq mm multi stranded copper conductor cable as continuous earth wire drawn with wiring and connected to common earth dolly complete all as specified and directed :- Make of wire: Polycab/Plaza/HavellsNote:Blanking plate,Modular cover plate ,Switches, sockets outlets, Light fittngs, fans, bells & regulators shall be measured and paid for separetely). |
| 135 | All as per Sl No. 134 above but Wiring with 2.5 Sqmm copper multistranded unsheathed cable and 2.5 Sqmm copper cable for earth continuity conductor controlled by one 15A switch socket independently complete all as specified and directed. |
| 136 | S&F factory madepowder coated distribution board SPN 12 way double door,includingbus bar, Neutral bar, standard DIN rail, earth bar complete including taking down unserviceable DBall as specified and conforming to IS: 8623, all as specified and directed. Make : Legrand/ L&T/ Indo Asian |
| 137 | S & F MCB SPN 240 volts 32 Amps \"C\" curve 10 KA breaking capacity complete including taking down unserviceable fitting complete all as specified and as directed .Make : Legrand/ L&T/ Indo Asian. |
| 138 | Supply and fiixing of Wall mounted fan metal body 450 mm sweep high speed, single phase, 50 Hz energy efficient, 230 Volts, copper winding conforming to ISI complete with necessary connection upto ceilling rose all as directed .Make-Havells /Bajaj/ Crompton Greaves/Almonord |
| 139 | M&L for cutting of hole through cement concrete wall including providing, fixing and removing shoring,cleaning,internal plastering and removing surplus hard core,rubbish not exceeding 50 mtrs including fixing of exhaust fan of size 450 mm all as specified and as directed. |
| 140 | S&F factory madepowder coated distribution board SPN 8 way double door,includingbus bar, Neutral bar, standard DIN rail, earth bar complete including taking down unserviceable DBall as specified and conforming to IS: 8623, all as specified and directed. Make : Legrand/ L&T/ Indo Asian |
| 141 | S & F MCB single pole 240 volts 6 to 32 Amps \"C\" curve 10 KA breaking capacity complete including taking down unserviceable fitting complete all as specified and as directed.Make : Legrand/ L&T/ Indo Asian. |
| 142 | Supply and installwater heater storage type (Geyser) vertical of capacity 25 Ltr, suitable for high pressure up to 8 barpowder coated metal body, temperature indicating dial , glass line coated tank, magnesium anode,efficient long life copper heating element, wattage 2 KW electrically operated, AC 230 Volt, BEEStar Rated with complete fittings/partsand accessories for fixing on wall/surfaceall as per site requirement complete all as specified anddirected Make:- Bajaj / Racold / Havells |
| 143 | Supply and fixingin repair 20 mm dia Chlorinated PVC (CPVC) Pipes of pressure rating 10kgf/cm2including fittings like socket / union / Tee / Reducer / Nipple etc complete fixed to wall/ceilings/ in floors etc, complete all as specified and directed. |
| 144 | Supply and fixing of 15 mm dia Stop valves, fancy type, chromium plated with long shank and cup(concealed type),screwed down,high pressure,with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed completeall as specified and as directed. |
| 145 | S & F bib tap cast copper alloy chromium plated, fancy type screwed down with screwed both ends for iron pipe 15 mm borecompleteall as specified and as directed. |
| 146 | Supply and fixing of UPS 1100 VA minimum 30 min Backup with wall mounted steel stand complete all as directed. Make : APC/Luminous/ True Power/HP/Intex/ Techser Power Solution |
| 147 | Supply and fixing LED flood light 70 watt 230 V AC outdoor type including necessary bracket with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp including taking down of old unserviceable fitting of any capacity. Make : Halonix/Philips/CG/Bajaj |
| 148 | Supply and fixing exhaust fan with louvers, ball bearing. silent operation, PVCbody and blades with fixing arrangements of size 150 mm sweep, Speed not less than 1000 rpm, 240V, Make Havells / Bajaj/CG/Usha. |
| 149 | M&L exhaust fan 450 mm ,high velocity heavy duty metal, double ball bearing. silent operation, speed not less than 2000 rpm, 240V, Make Havells / Bajaj/CG/Usha. |
| 150 | Supply & Fix automatic mud water submersible pump of capacity 1HP, single phase 240Vincluding DOL starter and control wiring, complete all as specified and as directed. |
| 151 | Supply and fixing water Hose strong HDPE pipe of size 1.5 inch dia complete all as specified and as directed. |
| 152 | Supply, installation, testing & commissioning of maintenance free chemicalearthing system comprising of 17mm dia copper bondedrod 3 mtr long horizontally pre welded T-terminal rod with provision for connection size of 50 x 150mm long, 6mm thickness with equal space either side, with 12mm dia hole of 02 numbers each on either side of the terminal clamp with 250 microns (average) coating thickness, tested and certified by CPRI India alongwith 50 Kg earth energizer compound and 10 litres earth resistance reducingliquid. The earthing energizer compound and resistance reducing earthing liquid shall be tested as per IEC-62561-7 read with ASTM G57-06, CI 3.4 A by any NABL accredited lab. The above mentioned rod shall be installed in 4-6 inch bore, 12 feet depth with a distance of minimum 3 meters between each installation complete all as specified and directed..Make : Model HTSP 317 of safeTrode or equivalent in Snaga/ Cubes 6 Global |
| 153 | The quoted rate shall also deemed to be included the following :- (i)Prior toinstallation of maintenance free chemicalearthing, soil resistivity test to be carried out at the location where earthingwork to be donein presence of Engr-in- Charge/JE (E/M),user and the report has tosubmitto Garrison Engineer with recommendation of manufacturer, if required additional interconnection ofearthing (not more than 08 number of earthing) to achive earth result less then 1 Ohms. The arrangement done for soil resistivity testingandsubmission of report with recommendationdeemed to be included in the quoted rate. |
| 154 | (ii) The description/ size/ qty of items mentioned in above are for indicating only however qty/ size may vary at site condition to maintain the earth resistance 1 ohm. The contractor shall quote rate by considering all factors. |
| 155 | (iii) Rateofearth energizer compound of 25 Kg of 02 bags and earthresistance reducingliquid 10 litre per cane for each pit deemed to be included in the quoted rate. |
| 156 | (iv)Resistivity of earth energizer compound and resistance reducing earthing liquid shall be certified by any NABL accredited lab carried out as per IEC-62561-7 read with ASTMG57-06, CI-3.4A and the certificate of same shall be submitted by the contractor along with the sample approval |
| 157 | (v) Earth enhancing material should not leach into the adjacent soil or underground water channels and its PH value should be in neutral range complete all as specified and as directed. It should solidify when mixed with water and set like concrete. |
| 158 | (vi) Copper strip of size 20 x 3 mm shallbe fixed on proper post insulator at the instrument end (copper strip upto 7.5 RM shall be considered in unit quoted rate and extra will be measured and paid separately). |
| 159 | (vii)Testing of earth shall be carriedout in presence ofdepartmental and user representativeand report shall be submitted to Garrison Engineer duly signed by all concerned. |
| 160 | (viii)Earth resistance tester will be provided by the contractor.Tester should be calibrated from authorised company/ lab. |
| 161 | (ix)Earthing shall be tested after completion of work by the contractor in presence of Engr-in-charge, user and proper record shall be maintained duly signed by all concerned.After testing if the desired earth resistance of less than 1 Ohm is not obtained, the earthing will be redone at no extra cost to Govt. till desired result is obtained. |
| 162 | (x) The contractor shall give a written guarantee of minimum three years for maintaining the earth resistance less than 1 Ohm after certified date of completion. |
| 163 | (xi) No further maintenance or periodic watering or recharge shall be required in earthing during its guarantee period of over 03 years in all type of soil including soft/ disintegrated or hard rock. |
| 164 | (xii) During the guarantee period, if earth resistance is not maintained less than 1 ohm the contractor has to redo or rectify at no extra cost to Govt till desired result is maintained. |
| 165 | (xiii) A security deposit of value equal to 2.5 % of the rate quoted for chemical earthing for each earthing shall be retained from payment due to the contractor from final bill for the guarantee period. |
| 166 | (xiv) The electrode shallcarry manufacturer\"s name . |
| 167 | (xv) The connection clamp shall be permanentlly welded to the copper boundedrodto avoid any kind of connectivity loss,.The pre-welded copper bounded rod shall not need any additional clamp for termination. |
| 168 | (xvi) The acceptable earth resistance at earth busbar/ test point shall not be more than 0.1 ohm. |
| 169 | (xvii)Earth work such as auguring andmaking good the surrounding area shall carried out in any type of soil. |
| 170 | (xviii)The contractor shall submit CPRI India certified document for copper bounded rod to ensure genuineness of material. |
| 171 | (xix) Sign boardof mild steel sheet 2 mm thick duly painted with two coats of synthetic enamel paint over a coat of red oxideZinc chrome primer showing result of earthing shall be fixed near the earth pit after completion as directed by engr -in- charge. |
| 172 | Material and labour for Earth pit cover madeof heavy duty poly plastic of high grade polypropylene tested and certified by any NABL accredited lab for load bearing capacity not less than 7.2 tonnes with top dia not less than 250mm, bottom dia not less than 330 mm and height not less than 260 mm for each electrode pit complete all as specified and directed.Make : Model SEPC 250 of SAFE TRODE or equivalent in Snaga/ Cubes 6 Global |
| 173 | Note :- An amount of Rs 25,560.00 on account of credit schedule for schedule \"A\" part II shall be deducted from the total amount of BOQ to arrive at the contract sum. |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
