|
| 1 | General Notes:1. Contractor shall inspect the site to acquaint with the site conditions as well as security conditions at AMD.2.The rates quoted shall include cost of all tools and tackles, manpower including wages, liveries, all wastages and taxes GST, Labour cess, IT, etc., as applicable but exclusive of EPF and ESI.EPF and ESI are reimbursable as per relevant clause. |
| 2 | Demolishing brick work in cement mortar manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. |
| 3 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead as per direction of Engineer-in-charge. |
| 4 | Dismantling tile workin floors and roofs laid in cement mortar including stacking material within 50 metres leadas per specification anddirections of Engineer-in- Charge |
| 5 | Dismantling doors shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead |
| 6 | Taking out existing wooden door shutter, repair by cutting, plaining etc. and refixing of repaired door shutters to existing door frames, including replacement with new SS hinges with SSscrews, etc. as required, all complete as per the direction of the Engineer-in-charge. |
| 7 | Providing and laying in position cement concrete ofgrade1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)excluding the cost of centering and shuttering - All work up to plinth level |
| 8 | Providing and laying 600x600 mm Vitrified tiles in floor (thickness of tiles to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including using spacers for making joints of 3 to 5 mm width for groutingusing epoxy grout mixcomplete as per direction of Engineer-in-charge, grouting joints using epoxy grout mixshall be paid seperately under relevant item. |
| 9 | Grouting the joints of flooring tiles having joints of 3 mm to 5mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. |
| 10 | Providing and fixing 12 mm thick frameless toughened frosted glassdoor shutter of approved brand and manufacture, openable panels (doors) with crystal edge polish and necessary patch fittings for swing doors, hunged on floor spring, , S.S.handles and locking arrangement and clear toughened float glass fixed for fins and all joints sealed with weather silicone sealent includingmaking necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Floor spring, Door handle, lock and stopper etc.to be paid separately). |
| 11 | Providing and fixing double action hydraulic floor spring for door weight upto 150 kg, (door size 1200wide)of approved brand and manufacture conforming to IS : 6315( Godrej/Ozone equivalent), having brand logo embossed on the body / plate with double spring mechanism, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with S.S pivot and single piece S.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. |
| 12 | Providing and fixing Stainless Steel tubular Pull H Type handle bar 32 x 600 mm size with SS screws etc.of approved brand and manufacture ( Godrejequivalent)ontoughened float glassdoor shutter complete as per direction of Engineer-in-Charge. |
| 13 | Providing and fixing Glass to Glass SS 304 Round Lock with 6 levers of approved brand and manufacture ( Godrejequivalent) ontoughened float glassdoor shutter complete as per direction of Engineer-in-Charge. |
| 14 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door frame size 45 x 70 mmcomprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. |
| 15 | Providing and fixing factory made single extruded 30 mm thick WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 16 | Providing and inserting 12mm dia galvanised steel injection nipple in honey comb area and along crack line forgroutingincluding drilling of holes of required diametre (20mm to 30mm) up to depth from 30mm to 80mm at required spacing and making the hole & crack dust free by blowing compressed air, sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction ofE.I.C. |
| 17 | Providing and injecting approved Epoxy injection grout in concrete/RCC workin proportion recommended by the manufacturer into cracks/honey-comb area of concrete/ masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of E.I.C. (The payment shall be made on the basis of actual weight of approved grout injected.) |
| 18 | Chipping of unsound/weak concrete material (50 mm average thickness)from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge |
| 19 | Providing, mixingandapplyingSBRpolymer(ofapprovedmake @ minimum 2% by wt. of cement used) 50 mm thick modified plain cement concrete in Grade M25 with cement content not less than 330 kg per cum having minimum characteristic compressive strength [with ordinary portland cement, coarse sand and graded stone aggregate of 10 mm maximum size in proportion as per design criteria] with specified average thickness.Note: Rates shall be for finished surface area of concrete and shall include the cost of labour, concrete and appropriate approved Super-Plasticiser for rendering concrete as flowable and SBR polymer but shall exclude cost of reinforcement, bond coat, Shear Keys, centering and shuttering, strutting, propping etc (Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/tapping with a blunt metal instrument) |
| 20 | Providing, mixing and applying 25 mm average thickness in 2 layers SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge.Note: Measurement and payment: The pre-measurement of thicknessshall be done just after the surface preparation is completed and Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2).all complete as per the direction of Engineer-In-Charge. |
| 21 | Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding and all as per specification anddirections of E-I-C. |
| 22 | Wall painting in two coats with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour and all as per specification anddirections of E-I-C. |
| 23 | Varnishing one or more coatswith varnish of approved brand and manufacture all as per specification anddirections of E-I-C. |
| 24 | Providing and applying one or more coats on old work withsynthetic enamel paint of approved brand and manufactureof required colour to give an even shade on doors, windows, grills etc. after thouroughly rubbing/ brushing the surface, filling the cracks with necessaryapproved putty to give uniform shade, preparing the surface free from all grease, dirt, loose pieces of scales, including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specification and direction of E-I-C.13.99.1 One or more coats on old work sqm 102.80 |
| 25 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shadeand colour intwo or more coats applied @ 1.43 ltr/ 10 sqm all as per specification anddirections of E-I-C. |
| 26 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved as per specification anddirections of Engineer-in- Charge. |
| 27 | Steel work welded in built up sections/ framed work in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required as per specification anddirections of Engineer-in- Charge. |
| 28 | Providing and fixing White Vitreous China Wash basin size 630x450 mmwith C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require as per specification anddirections of Engineer-in- Charge |
| 29 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings complete as per specification anddirections of E.I.C. |
| 30 | Providing and fixing 40 mm dia P.V.C. Semi rigidwaste pipe for sink or wash basin including P.V.C. waste fittings complete as per specification anddirections of Engineer-in- Charge |
