|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 2 | All kinds of soil. |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lif. |
| 4 | Providingandlayinginpositioncementconcreteof specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 5 | 1:2:4 (1cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 6 | 1:4:8 (1Cement : 4 coarse sand (zone-Ill) derived from natural sources: 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 7 | Providing and laying in position specified grade of reinforced cement concrete,excludingthecostofcentering,shuttering,finishingand reinforcement - All work up to plinth level : |
| 8 | 1:1.5:3(1 cement: 1.5 coarse sand (zone-Ill) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 9 | Reinforced cement concrete work in walls (any thickness),including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor fivelevel,excludingcost of centering,shuttering, finishingand reinforcement: |
| 10 | 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 11 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 12 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 13 | Foundations,footings,basesof columns,etc.formass concrete |
| 14 | Suspended floors,roofs,landings,balconies and access platform |
| 15 | Shelves (Cast in situ) |
| 16 | Lintels,beams,plinthbeams,girders,bressumersand cantilevers |
| 17 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 18 | Weather shed, Chajjas, corbels etc., including edges |
| 19 | Steelreinforcement forR.C.C.workincludingstraightening,cutting, bending, placing in position and binding all complete above plinth level. |
| 20 | Thermo-Mechanically Treatedbars of gradeFe-500D or more. |
| 21 | Providingandfixing 18mmthickgangsawcut,mirrorpolished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters,window sills,facias andsimilar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. |
| 22 | Granite stone slab of colour black, Cherry/Ruby redArea of slab over 0.50 sqm |
| 23 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. |
| 24 | Granite work |
| 25 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3(1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 26 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. |
| 27 | Fixed to openings /wooden frames with rawl plugs screws etc. |
| 28 | Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 29 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 30 | 300x16 mm |
| 31 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 32 | 250x10 mm |
| 33 | 150x10 mm |
| 34 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 35 | Twin rubber stopper |
| 36 | Providing and fixing factory made uPVC door frame made of uPVC extrudedsectionshavinganoveralldimensionasbelow(tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1 mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer\"s specification and direction of Engineer- in-charge |
| 37 | Extruded section profile size 42x50 mm |
| 38 | Providing and fixing to existing door frames. |
| 39 | 24 mm thick factory made PVC door shutters made of styles cleats. The shutter frame filled and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mmhavingwallthickness1.0mmandstainlesssteel screws. The styles of the shutter reinforcedby inserting galvanised M.S. tube of size 20x20 mm and 1mm (± 0.1 mm) wall thickness. The lock rail made up of \"H\" section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer\"s specification and direction of Engineer- in-charge. (For W.C. and bathroom door shutter). |
| 40 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 41 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 42 | Electric resistance or induction butt welded tubes |
| 43 | Providing and fixing mild steel round holding down bolts with nuts and washer plates complete. |
| 44 | Providing and fixing bolts including nuts and washers complete. |
| 45 | Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. |
| 46 | G.I. pipes |
| 47 | Cement concrete flooring 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 48 | 40 mm thick with 20 mm nominal size stone aggregate |
| 49 | Providing andlayingCeramic glazed floor tiles of size 300x300mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 50 | Providingand fixingplainmultipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately). |
| 51 | 6 mm thick Cement fiber board, Type-B, Category-III as per IS: 14862 :2000 |
| 52 | Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : |
| 53 | Ridges plain (500- 600mm) |
| 54 | 12 mm cement plaster of mix: |
| 55 | 1:4(1 cement: 4 fine sand) |
| 56 | 12 mm cement plaster finished with a floating coat of neat cement of mix: |
| 57 | 1:3(1 cement: 3 fine sand) |
| 58 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour: |
| 59 | New work(twoormorecoats)over andincludingwater thinnable priming coat with cement primer having VOC content less than 50 gram/litre |
| 60 | Finishing walls with Acrylic Smooth exterior paint of required shade: |
| 61 | New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 62 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 63 | Two or more coats on new work |
| 64 | Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade: |
| 65 | Two or more coats on new work |
| 66 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. |
| 67 | With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre |
| 68 | Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in- charge. |
| 69 | Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade |
| 70 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: |
| 71 | White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 72 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : |
| 73 | Kitchen sink without drain board610x460 mm bowl depth 200 mm |
| 74 | Providing and fixing kitchen sink including making all connections excluding cost of fittings. |
| 75 | White glazed fire clay sink of size 600x450x250 mm |
| 76 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 77 | Semi rigid pipe32 mm dia |
| 78 | Providing and fixing soil, waste and vent pipes : |
| 79 | 100 mm diaSand cast iron S&S pipe as per IS: 1729 |
| 80 | 75 mm diameter :Sand cast iron S&S pipe as per IS: 1729 |
| 81 | Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : |
| 82 | 75 mm dia pipe |
| 83 | 100 mm dia pipe |
| 84 | Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. |
| 85 | 75 mm diaSand cast iron S&S as per IS - 1729 |
| 86 | Providing and fixing plain bend of required degree. |
| 87 | 100 mm diaSand cast iron S&S as per IS - 1729 |
| 88 | 75 mm diaSand cast iron S&S as per IS -1729 |
| 89 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall |
| 90 | 15 mm nominal dia Pipes |
| 91 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.External work |
| 92 | 15 mm dia nominal bore |
| 93 | 25 mm dia nominal bore |
| 94 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : |
| 95 | 25 mm nominal bore |
| 96 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work): |
| 97 | 15 mm nominal bore |
| 98 | 25 mm nominal bore |
| 99 | Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISI : 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support Including fittings & fixtures for tank shall be paid separately. |
| 100 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : |
| 101 | 15 mm nominal bore |
| 102 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. |
| 103 | 15 mm nominal bore |
| 104 | Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately). |
| 105 | Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto 1200 mm length), fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40x3 mm size 60 mm long and stainless steel expandable dash fastener of 12.5 mm dia and 50 mm long, complete as per direction of Engineer- in-charge. |
| 106 | Constructing soak pit 1.20x1.20x1.20 m filled with stone aggregate 20mm including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. |
| 107 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position :a) Superiorhard woodCat-II(A) |
| 108 | Providing and fixing 35mm panelled, glazed or panelled and glazed shutters for doors including oxidised mild steel butt hinges with necessary screws with superior hardwood category No. II(A)including panelling with 12 mm thick marine plywood (BWR) confirming to relevent specification with wooden cleats and block and as directed by Engineer in charge. |
| 109 | Providing and fixing 35mm glazed shutter for windows with superior hard wood category II.using 10 kg/sqm (4mm) glass panes including oxidised M.S. butt hinges with necessary screws etc. complete. |
| 110 | Providing and fixing pre-painted galvalume (PPGL) steel profile sheets AZ-150 of brand Tata Bluescope steel, Everesrt Industries Ltd., JSW Steel Ltd., Jindal India Ltd. or equalavent(size,shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05%) total coated thickness with aluminium zinc coating 150 grams per sqm as perIS : 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping aluminium screws (Xylan) of size (5.5x55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 111 | Providing and laying hollow cement concrete block walling upto floor five level 200 mm thick using consisting of hollow block of size 400 x 200 x 200 mm of mix 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregates 10mm nominal size) having crushing strength 3.5 N/mm 2 at 28 days as per I.S 2185(Part I) 1979laid in cement mortar 1:6 (1 cement : 6 coarse sand) complete. |
| 112 | Providing and laying hollow cement concrete block walling upto floor five level 100 mm thick using consisting of hollow block of size 400 x 100 x 200 mm of mix 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregates 10mm nominal size) having crushing strength 3.5 N/mm 2 at 28 days as per I.S 2185(Part I) 1979laid in cement mortar 1:6 (1 cement : 6 coarse sand) complete. |
| 113 | Distempering with 1st quality acrylic distemper,having VOC ( Volatile Organic Compound content less than 50 gms/litre, of approved brand and manufacturer, including apply additional coats wherever requited, to achieve even shade and colour. |
| 114 | Two coats |
| 115 | Makingplinthprotection 50mmthickofcementconcrete 1:3:6 (1cement : 3 coarse sand (zone-Ill) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75 mm thick bed of stone aggregate 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 116 | Providing and fixing in position eaves or facia board with 18mm thick and 30cm wide with HDMR board including fixing with nuts and bolts etc complete as per direction of Engineer in charge. |
| 117 | Providing and fixing brass aluminium hooks and eyes conforming IS:8931: |
| 118 | 150 mm |
| 119 | Extra for providing and fixing aluminium section [40x6mm] wind ties of required size. |
| 120 | Providing and fixing PVC gully or Nahani trap in floor with PVC grating of size: |
| 121 | 75 mm |
| 122 | Providing and fixing PVC pipes for drain outlet. |
| 123 | 75 mm dia |
| 124 | Constructing cement concrete masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement:3coarsesand)finishedwithfloating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : |
| 125 | Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :With Cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size). |
| 126 | Providing cement concrete surface drain including earth excavation 10 cm thick base concrete and 15 cm thick side walling with 1:3:6 (1 cement : 3 sand: 6 graded stone aggregte 40 mm nominal size) cement concret finishing with 1:4 cement mortar (1 cement : 4 sand) cement plaster including floating coat of neat cement inside the drain surface including disposal of surplus earth work complete. |
| 127 | 15 cm X 15 cm |
| 128 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : |
| 129 | 15 mm nominal bore |
