Tender For Special Repair To Bldg No P/179 Hamid Enclave Under Ge Panagarh.; 1 Demolition of PCC in ground floors & pavings n exc 15 cm thickness (below or above ground level)(unreinforced) complete all as specified and directed. 2 M&L for brick work with fly ash bricks old size, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed. 3 M&L for brick work with fly ash bricks old size, straight or curved on plan exc 6m mean radius, in half brick walls built in cement mortar 1:4 complete all as specified and directed. 4 Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and as directed. 5 Taking down cement plaster on brick or stone wall etc. including racking out joints hacking for key scrubbing down with water etc complete all as specified and as directed. 6 M&L for Rendering 15 mm thick cement plaster in CM 1:4 onfair faces of brick/concrete surfaces finished fair and even, mixed wth water proofing compound admixture (if directed) as per manufacturers instruction,complete all as specified and directed.Note :- WPC will measuered and paid separatly under relevant item of schedule. 7 Supply only liquid WPC, ISI marked complete all as specified and as directed. 8 Material & labour preparation of newly plastered surfaces of wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces on external surface including putty over plastered surface to prepare the surface even and smooth as directed by Engineer-in-charge 9 M&L for rendering 15 mm thickon other than fair faces of brick work or concrete surfaces, finishedfair and even on walls in cement mortar (1:6), complete all as specified and directed. 10 Material & Labour for preparation of new surfaces of plastered walls and applying Twocoats ofDistempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturers specification. over and includinga coat of primer and 1.0 mm thick white wall care putty (premiumquality) over plastered surfaces of walls to prepare the surface even and smooth complete all as specified and directed. 11 M&L for rendering 5mm thick on fair faces of ceiling / chajja concrete surfaces in cement mortar 1:3 complete all as specified & directed. 12 M&L for prepartionof newly plastered ceiling/chajja surfaces and applyingthree coats of white wash complete all as specified and directed. 13 Taking down chowkat or frames exc 1.5 sqm but n exc 4.0 sqm each with shutter (without taking off shutters from the frame) and removing to or from store complete all as specified and as directed. 14 Taking down Chowkats or frames not exc. 1.5 sq. m each with shutters (without taking off shutters from the frames) and removing to or from store complete all as specified and as directed. 15 M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50X100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardan and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engr-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.edepth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and as directed. 16 M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50X125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardan and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engr-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.edepth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and as directed. 17 S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S Sscrews shall be paid separately) complete all as specified and as directed. 18 All as per BOQ Srl No 17.00 but with wire gauzed shutter will bewire mesh in lieu WPC , the wire gauze shall be warped on additional square 8mm MS Solidtube and this tube shall bewelded to MS frame complete all as specified and as directed. 19 S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing complete all as specified and directed. 20 S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC C channel having a PVC sheet trip of 20mm with stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing complete all as specified and directed. 21 Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 122 x 54 mm & sash 47 x 64 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately). Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 22 Providing and fixing factory made uPVC white colour fixed window,area not exceeding 1.00sqm each made of extruded profiles with wall thickness of 2.3mm(+-0.2mm). Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profile (Onevertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2 +–0.2mm thick, galvanized steel Frame (28mm x 21.5mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners- 5mm thick glazing with selected quality glass (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories Net opening will be measured for payment purpose.) 23 S&F 100 mm butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-22,complete all as specified and directed. 24 S&F 75 mm butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21,complete all as specified and directed. 25 S&F aluminium anodised 150 mm barrel tower bolts of extruded section complete all as specified and directed. 26 S&F aluminium anodised 75 mm barrel tower bolts of extruded section complete all as specified and directed. 27 S&F 150 mm long extruded aluminium alloy handles,fabricated type, anodised complete all as specified and directed. 28 S&F 100 mm long extruded aluminium alloy handles,fabricated type, anodised complete all as specified and directed. 29 S&F Aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed. 30 S&F in repairs Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed. 31 S&F Hasp and staple,75 mm long, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and as directed. 32 S&F Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed, complete all as specified and as directed. 33 S&F Floor door stopper of brass body 140 mm and tongue, anodised, with hard drawn steel spring & end rubber shoes, fixed in floor, complete all as specified and as directed. 34 M&Lfor 4mm thick figured glass, pin head type and glazing with oil putty in square n. exc 0.5 sqm in each pan for bathrooms/toilets ventilators all as directed 35 M&Lfor 4mm thick,ordinary quality and glazing with oil putty in square n. exc 0.5 sqm in each pan for bathrooms/toilets ventilators all as directed 36 M&Lfor 4mm thick,ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pan for bathrooms/toilets ventilators all as directed 37 M&L for 100 mm thick plain cement concrete 1:2:4 Type B-1, (using 20 mm graded crushed stone aggregate) as in sub bases with nominal reinforcementcomplete all as specified and directed 38 M&L Mild steel TMT bars 6mm to 8 mm dia, cut to length, bent to shape required, including cranking, bending pirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 39 Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. 40 M&L Non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 sqm in floors laid over 15mm thick 1:6 cement mortar screed bed etc. set and jointed in neat cement slurry and pointed in white of coloured cement to match complete all as specified and directed. 41 M&L Non Skid ceramic coloured tiles7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm,in floors/skirting etc. laid over 15mm thick 1:6 cement mortar screed bedset and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. 42 M&L Glazed ceramic coloured tiles in vertical surface 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match all complete all as specified and directed. 43 M&L for Rendering 10 mm thick in CM 1:4 finished even and fair on vertical surfaces on wall to receive wall tiles,complete all as specified and directed. 44 M&L40 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) as in roof padding, finished fair and even without using extra cement from roof surfaces complete all as specified and directed. 45 M&L for screedbed 10 mm thick on fair faces on roof surfaces of concrete surfaces in cement mortar 1:4 even and smooth complete all as specified and directed. 46 M & L for providing water proofing treatment with a layer of APP based polymeric membrane, 3 mm thick (minimum), weighing not less than 3.60 kg/Sqm reinforced with polymer non woven fabric (weighing not less than 160 gm/ Sqm) shall be applied over one coat of cold bituminious primer @ 0.40 ltr/ Sqm ( membrane shall be laid using butane torch and sealing all joints etc, complete all as specified and directed .( Note: The overlaps shall be of minimum 75 mm on longitudinal direction and 100 mm on transversedirection) complete all as specified and directed. 47 M&L for two coats of aluminium paint over APP membrane, over 10cm in width or girth,not otherwise described complete all as specified. 48 S&FMS work such as Chimney bars (straight orcamber); bearing bars; tonguesor water bars for window frames;window guard bars, plain, let inand fixed independently inwooden frames, L or T section supports for shelves etc. andsimilar articles conforming toFe-290 Gde E-165 conforming to Fe-290, Gde-E-165 the grill shall be inseted in the wall surface including necessary drilling and grouting with cement etc, complete all as specified and directed. 49 M&L Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling,boltingor riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. 50 S&F Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290, Gde-E-165 the grill shall be inseted in the wall surface including necessary drilling and grouting with cement etc, complete all as specified and directed. 51 Dismanting of wrought iron or mild steel work af any description not otherwise provided for complete all as specified and as directed by Engineer-in-charge 52 M&L & preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer of any description not otherwise described over 10 cm width or girth, complete all as specified and directed. 53 Demolition of Concrete (RCC)of any description and in any position not otherwise specifically provided for complete all as specified 54 M&L for RCC (Nominal mix) M-20, using 20 mm graded crushed stone aggregate as in chajja complete all as specified and directed. 55 M&L for RCC (Nominal mix) M-20, using 20 mm graded crushed stone aggregate as in slabs supported on walls, beams and columns, in roofs, landings,deck slab and in shelves and the like complete all as specified and directed. 56 Use and waste of fair finish formwork to sides of chullah hoods, chajjas complete all as specified and directed. 57 M&L for RCC (Nominal mix) M-20, using 20 mm graded stone aggregate as in Fins, fascias, louvres, parapets, and railings exc. 60cm in height, newels, balustrade, and the likecomplete all as specified and directed. 58 Use and waste of fair finish formwork for sofits of slab complete all as specified and directed. 59 M&L for RCC (Nominal mix) M-20, using 20 mm graded crushed stone aggregate as in coloums complete all as specified and directed. 60 M&L forRCC (Nominal mix) M-20, using 20 mm graded crushed stone aggregate as in beam and lintels complete all as specified and directed. 61 Use and waste of fair finish formwork for coloums complete all as specified and directed. 62 Use and waste of formwork for sides and sofits of beams and lintels complete all as specified and directed. 63 M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending pirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 64 M&L Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups , spacers and binders, cut to length, bent to shape required, including cranking, bending pirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 65 Use and waste of fair finish Formwork to edges of concrete flats, treads, breaks in floors, window cills, concreterailings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed. 66 Use and waste of fair finish Formwork to edges of concrete flats, treads, breaks in floors, window cills, concreterailings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide complete all as specified and directed. 67 M&L for applying two coats of Super Latex(Sika or equivalent) @ 80gm per sqm per coat in the ratio of 1:1.5:5 (latex : water : cement)over internal/external of brick/concrete surface after cleaning and washing the surface by wire brush and plenty of water The entire surface shall be washed throughly with plenty of water and then allowed to dry complete all as specified and as directed. Note:- The entire process executed by authorised applicator. 68 M&L Machine cut kota stone slab flooring 18-20 thick over cement screed laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified and directed. 69 M&L Kota stone slab 16mm thick in riser of steps, skirting, dado & pillar over plaster & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified and directed. 70 M&L for Green marble work 16 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following typesnt with admixture of pigment to match the shade of granite stone including grinding and polishing complete over 15mm thick Screed bed or backing coat for laying floor finishes in CM 1:6 complete all as specified and directed. 71 M&L for 16 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, including screed bed of 20mm thick in 1:4 cement mortar, complete all as specified and as directed. 72 M&L for 75 mm thickcement concrete M10 (Nominal Mix) with 40mm graded crushed aggregate finished even and fairlaid to a slope of 1 in 12, laid in alternate bays, each bay not exceeding 3 m length with joint filled with bituminous mastic filling comprising a mixture of 1 part of heated Industrial bitumen 85/25 grade and two parts of heated sand as in plinth protection complete all as specified 73 M&L Plain Cement Concrete 1:3:6 type C1 (using 20 mm stone aggregate) as in surface channels and drains, complete all as specified and directed. 74 S&F in repairs 15 mm bore Stop valve fancy type, chromium plated with long shank and cup concealed type cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and directed. 75 S&F in repairs Gun metal, globe or gate valve with iron wheel head, 20 mm bore,screwed both ends for pipe complete all as specified and as directed. 76 S&F in repair CP Bib taps 15mm dia, with cfancy handle, screwed down, screwed for iron pipe or for brass ferrule, fency type and fixed complete all as specified and directed. 77 S&F in repairStop valve cast copper alloy screwed down high pressure with capston headed handle chromium plated concealed type screwed both ends for pipe 15 mm bore or for unions complete all as specified and as directed. 78 S&F in repair fancy,chromium plated Stop valves 15mm dia, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. 79 S&F in repair angle cock 15 mm bore fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe complete all as specified and as directed. 80 S&F in repair chromium plated 15mm central hole basin mixer single lever without popup waste system with 450mm long braided hoses complete all as specified and as directed. 81 S&F in repair wall mounted mixer for Bathroom, made of brass, chrome polish finish, without hand shower, complete all as specified and as directed. 82 S&F in repair stainless steel kitchen plate rack(24x24x10) including necessary fixing/fitting & making good the existing surface complete all as specified and directed . 83 S&F in repairs 40mm wide and 5mm thick PVC door seal (snake guard) with powder coated aluminium frame. 84 S&F in repair soap dish, any type fixed to plugs chromium plated brass screws complete all as specified and as directed. 85 S&F in repair glass self assembly consisting of 5.5 mm thick glass sheet glass self 12 Cm wide with CP bracket gaurd and railing 60 Cm long complete all as specified and as directed. 86 S&Fin repair chromiuim platedSwivel shower roses with shower arm, 125 mm size including fxing to steel pipe or union etc complete all as specified and as directed. 87 S & F in repairs vitreous china squatting pan, Orissa pattern, size 580 mm X 440 mm white with ‘P’ or ‘S” trap, front or back inlet and integral foot rests, any pattern and including fixing , connector to flush pipe, lime concrete bedding and making connections to flush pipe, connector to branch pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed by Engineer-in-Charge. 88 S&F in repairs PVC low level flushing cistern, 10 litres capacity, syphonic action type white body with inlet ball valve, float , handle,bracket, flush pipe etc complete & connecting to WC complete. 89 S&F in repairs Vitreous china wash basin, white, flat back, size 550x400mm excluding taps, waste, chain and plug and porcelain stopper butincluding brackets and 32mm bore GI pipe light grade complete all as specified and as directed. 90 S&FPVC connections 15 mm size with PTMT nuts of length 600mm complete all as specified and as directed. 91 S&F in repairs 32mm dia Waste coupling, brass , chromium plated for glazed ware , basins , etc. with long screwed shanks and fly -nuts , flange end bedded in red lead cement and other end fixed complete all as specified and as directed. 92 S&F in repairs 40mm dia Waste coupling, brass , chromium plated for glazed ware ,Sink basins , etc. with long screwed shanks and fly -nuts , flange end bedded in red lead cement and other end fixed complete all as specified and as directed. 93 S&F in repairs kitchen sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, couplingincluding bedding in cement mortar on to dwarf wall or including fixing cantilever brackets andconnecting union to pipe, overall size 915mmx460mm bowl size 410 mmx330mmx 160mm etc complete all as specified and as directed. 94 S&F in repairs grating square, Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms), complete all as specified and directed. 95 Taking up or down 15mm diaGI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed. 96 Taking up or down 20mm diaGI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed. 97 Supply & laying of CPVC pipes of 16 mm outer dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed. 98 Supply & laying of CPVC pipes of 20 mm outer dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed. 99 S&F in repair Vitreous China wash basin, white, flat back, size 450x300mm excluding Taps but includingbrackets including cutting for pinning in ends of brackets,complete all as specified and directed. 100 S&F in repairTubular towel rail, 20mm dia, D type, brass chromium plated, 60cm long between flanges complete all as specified and directed. 101 Supply & fix mirror 600mmx 400mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick AC building boardor commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. 102 S&F PVC plain bend (any radius) for 75 mm bore, PVC pipes, complete all as specified and directed. 103 S&F 75mm bore PVC (SWR) junction single, (single T) equal or unequal fitted with oval access door, complete all as specified and directed. 104 S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including dismantling old unserviceable existing pipe with fittings, complete all as specified and directed.[Note : Payment shall be made in net length as fixed between the fittings as per SSR Part-II preamble para (a) of Page 384.] 105 S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including dismantling old unserviceable existing pipe with fittings, complete all as specified and directed. 106 S&F PVC (SWR) bends, plain, 110 mm bore any radius, complete all as specified and directed. 107 S&F 110 mm bore PVC (SWR) junction single (single T) equal or unequal fitted with oval access door, complete all as specified and directed. 108 Supply only TMT bars 5mm dia and over cut to length, bent to shape required, complete all as specified and directed. 109 S&F in repair PVC door bends with oval access door (any radius) for 75 mm bore PVC pipes, complete all as specified and as directed. 110 S&F in repair PVC door bends with oval access door (any radius) for 75 mm bore PVC pipes, complete all as specified and as directed. 111 Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 and cutting chases for concealed water tubing and making good of groves for concealed GI tube, cutting not exc 10cm girth complete all as specified and as directed. 112 Rounding to edges of stone slabs one edge, such as in steps, cooking platform, granite/kota stone and other similar situations incl polishing, complete all as specified and directed. 113 S&F 18/19 mm thick, lead free PVC board Superior quality of density not less than 0.55 g/cm3as in moduler shutters/cabimet drawercupboard cabinet shutterincluding all frame work as specified and directed by Engr-in-Charge 114 M&L for Extra over rates for PVC lipping over PVC Sheet, fixed to PVC Sheet with necessary fittings, complete all as specified and directed. 115 S&F in repair soft closing O Degree (auto hinges) high grade mild steel bright finish or electro galvanised for cup board shutter complete all as specified and as directed. 116 S&F in repair magnetic catcher for kitchen cabinet shutter as approved by Engr-In-Charge. 117 M&L for Water proofing treatment to Sunken floor complete all as specified and directed in following steps :-(a) STAGE-I :Taking out old unserviceable treatment over sunken floor & clean the surface with wire brush, dirt less with water jet etc.(b) STAGE-II : Providing and laying water proofing treatment of sunken portion of WCs, bathroom etc. by applying two coats of cement slurry mixed with Acrylic based polymer modified cementorious composite compound coating (2:1) , of make as approved in Technical Instruction 5/2003.(c) STAGE-III : First layer of slurry of cement 0.488 Kg/Sqm mixed with Acrylic based polymer modified cementious composite compound @ 0.253 Kg/Sqm. This layer will be allowed to air cure for 4 hours.(d) STAGE-IV : Second layer of slurry of cement @ 0.242 Kg/Sqm mixed with Acrylic based polymer modified cementious composite compound @ 0.126 Kg/Sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.(e) STAGE-V : 200 micron thick polythene film pasted with the help of adhesivesover treatment.(f) STAGE-VI : Testing of all trap & joint and sunken slab shall be done as per IS-1742 & report to be submitted to Engr-in-Charge for claiming of payment. 118 S&F in repairs MS dropery rod of 25mm dia of PVC coated in curtain rod, complete all as specified and directed. 119 S&F in repairs MS PVC sheeted/powder coated bracket size 150mm made to shape suitable for holding curtain/drapery rod of 25mm dia fixed with PVC rail plugs and MS steel screws for single/double rods, complete all as specified and directed. 120 S&F for multipurpose lock 12mm to 25mm thick panel, for cupboard, cabinet, with brass srews, brass keys fixed to cabinet/cupboard, complete all as specified and directed. 121 S&F for Brass Handle for cupboard/cabinet, fixed with SS screws, complete all as specified and directed. 122 M&L for repair to crack portion with jacktting technique, taking down existing plaster upto brick wall surface of min 200 mm wide, cleaning to loose particles on surface of brick work along the length of crack and filling the gap/ crack area with PCC 1:1.5:3 type A0 using 12.5mm aggregate both side of the wall surface fixed with, drilling holes 10mm dia on either side of the crack by means of drilling machine through out the full width of the wall @25 cm c/c and insert 8/10 mm dia od in the drilled holes, welded with horizontal rod to with hold the welded mesh and applying grit plaster 1:1:2 using 4 mm and down aggregate finished even and smooth without using extra cement, complete all as specified and directed. (Note: Reinforcementwill be measured and paid separately as supply only) 123 Taking down carefully aluminium/Copper conductor point wiring (light , fan, socket or powr) complete including fittings such as switches, ceiling rose, pendents, regulators sockets etc and removing (except those to be reused shall be kept in safe custody at the site) and making good disturbed surfaces of walls, floors etc tomatch with the existing completeall as specified and directed. 124 M & L for concealed point wiringcomplete with 1.5 sq mm FRLSH ,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red Colour use for Phase & Black Colour use for Neutral),drawn into and including non metalic PVC rigid conduit medium grade of suitable size and conduit accessories fixed on wall, floor, roof etc. and WITHincludingofFRLSH PVC insulated 1.5 sq mm copper conductor for earth continuity (Green Colour)and connected to common earth dolly and including pressed steel terminal flush boxesmade out of 1.6 mm thick MS sheet suitable for modular switches concealed in wall , with and includingmodular cover plate with frame (suitable module) for housing the switches socket,outlet etc.,all as specified and directed by Engineer-in-Charge for one light point controled by one one way 5/6 Amp switch Note:-(a) Note :- Cost of PVC conduit, cutting chases of wall, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate. 125 All as per item No.124.00 above but5 Amp socket on same boardwith other switches. 126 Allas per ItemNo 124.00 mentionedhere-in- before but for onecall bellpoint controlled by one one way Bell switches. 127 All as item No.124.00 above but one light point controlled by two 2 way switches, with cables 1.5 sqmm size 128 All as per BOQ item No 124.00 here-in-beforebut for one power pointtusing by2.50 sq mm FRLSH,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red Colour use for Phase & Black Colour use for Neutral), and with and including FRLSH,PVC insulated multi stranded copper conductor single core 2.50 sq mmconductor for earth continuity (Green Colour) , on independent board( but Not below the switch board of light points in the same vertical plane). 129 All as per BOQ item No 124.00 here-in-beforebut for one power pointtusing by4.00 sq mm FRLSH,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red Colour use for Phase & Black Colour use for Neutral), and with and including FRLSH,PVC insulated multi stranded copper conductor single core 4.00 sq mmconductor for earth continuity (Green Colour) , on independent board( but Not below the switch board of light points in the same vertical plane). 130 Supply & Fixing switch modular type 6 Amp one way, one module, single phase, complete all as specified and directed. 131 S&F socket outlet 5 Amps, 5 pin, modular type, 2 module , single phase complete all as specified and as directed 132 Supply & Fixing switch modular type 16 Amp one way, one module, single phase, complete all as specified and directed. 133 S&F socket outlet 16 Amps, 5 pin, modular type, 2 module , single phase complete all as specified and as directed 134 Supply & Fixing switch modular type 6 Amp two way, one module, single phase, complete all as specified and directed. 135 Supply & Fixing bell push ,modular type 6 Amp SP one way, 1 module , complete all as specified and as directed. 136 Supply & Fixing fan regulator modular five step type 120 W 2 module suitable for 230 volt .cmplete all as specified and as directed. 137 Supply & fix ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified. 138 Supply and fixing lamp holder, PVC/polycarbomate type with back plate straoght of angle suitable for LED lamp complete all as specified and directed 139 Supply & fixed Buzzer, Ding dong, AC 230 Volts, single pole 230 volts all as specified and directed. 140 Supply and fixing for concealedtype sub main wiring with two run of 2.5 Sqmm single core PVC FRLSH PVC insulated unsheathed stranded copper conductor (Red/yellow/blue wires for phases and black wire for neutral) drawn in and includingthrough Rigid non-metallic PVC conduit(medium) ISI marked of size 25mm bore with all fittings like tee/Bend/Elbow/Reducer/Bell mouth/Junction / Terminal Boxesetc. and fixing accessories such as coupler, lock nuts, saddles, pipe hook etc.including one run of 2.5 Sqmm single core PVC FRLSH PVC insulated unsheathed stranded copper conductor as earth wire (green in colour) complete all as specified.Note : (i) Note : 2 runs of line conductor,one run of earth continuity conductor, one run of PVCconduit shall be measured as unit length. (ii)Cost of PVC conduit, conductors,making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate. 141 Supply and fixing for concealedtype sub main wiring with two run of 4.00 Sqmm single core PVC FRLSH PVC insulated unsheathed stranded copper conductor (Red/yellow/blue wires for phases and black wire for neutral) drawn in and includingthrough Rigid non-metallic PVC conduit(medium) ISI marked of size 25mm bore with all fittings like tee/Bend/Elbow/Reducer/Bell mouth/Junction / Terminal Boxesetc. and fixing accessories such as coupler, lock nuts, saddles, pipe hook etc.including one run of 4.00 Sqmm single core PVC FRLSH PVC insulated unsheathed stranded copper conductor as earth wire (green in colour) complete all as specified.Note : (i) Note : 2 runs of line conductor,one run of earth continuity conductor, one run of PVCconduit shall be measured as unit length. (ii)Cost of PVC conduit, conductors,making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate. 142 S & Fin repair LED street/security lights nominal power 35 Watt, LED of Make Osram; Everlight; Philips; Nicha; Cree; Samsung, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, lumenefficacy of minimum 110 lumens per watt, built-in integrated electronic LED driver, output open /short circuit protection, phase to phase protection, over voltage protection, surge voltage protection upto 4 KVs, protection grade IP 66, CRI greater than 80%, CW available CCT of 5700K, power factor of minimum 0.95, pressure die-cast aluminium alloy housing with epoxy powder coated metallic silver finish after phosphochromate treatment, life span of minimum 50000 working hoursincluding fixing at any height and including wiring using three core PVC insulated, PVC sheathed, flexible stranded copper conductor FR-LSH cables suitable for outdoor use, 1.5 sqmm as per IS 694: 2010 complete all as specified and as directed. 143 S&F in repairs LED 20 Watt tube light fittingintregatedtype, includingLED retrofit tubelamp 20 W , LED tube light nominal power 20 Watt, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 110 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 life span of minimum 50000 working hours and LED batten with aluminium housing and polycarbonate diffuser complete fittingincluding connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fittingcomplete all as specified & directed..Note (i) Make of batten and LED tube lamp should be of same make. 144 S&F decorative wall light gold finish fixture with glass diffuser suitable for Lamp type1 N x 9 watt lamp ,1 N x 7.5 watt LED filament lamp E-27 Base including fixing on wall with screw/plastic gitti etc,all as directed by Engr-in-Charge 145 S&F LED light fitting 1x9W/1x10W bulkhead luminaires aluminium housing and polycarbonate diffuserincluding LED light driver holder connecting up with three core flexible copper conductor cable of suitable complete all as specified and as directed 146 Supply and fixing round shape 12 watt 220 volts AC recessed type made by aluminium P-die-cast enclousers with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete. 147 S&F in repairs LED 9/10 Watt tube light fitting mirrorintregatedtype, includingLED retrofit tubelamp 9/10 W , LED tube light nominal power 9/10 Watt, L LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 115 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 extruded aluminium LED battenslife span of minimum 50000 working hours complete fittingincluding connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fittingincluding taking down old unserviceable complete all as specified & directed.Note : Make of batten and LED tube lamp should be of same make. 148 Supply and fixingventilating plastic body exhaust fan250 mm sweep 230 volt AC, complete with louver and all accessoriescomplete with fixing arrangement to wall connected with twin core twisted flexible copper conductorof suitable size all as directed. 149 S & F in repairs sheet metal enclosure for MCB, DB, TPN, 240 Volts, 100 Amps rated busbar, Confirming to IS as per IEC 61439-3, 4 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43 , IK 09 including fixing the DB box flush in wall of any type and making good the distrubed surface to match asthe existing withall as specified and directed by Engr-in-charge. 150 S & F in repairs sheet metal enclosure for MCB, DB, SPN, 240 Volts, 100 Amps rated busbar, Confirming to IS as per IEC 61439-3,12 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43 , IK 09 including fixing the DB box flush in wall of any type and making good the distrubed surface to match asthe existing withall as specified and directed by Engr-in-charge. 151 Supply and fixed in repairs MCB 4 pole, 415 volts fixed type 40 to 63Amps,C Curve with breaking capacity 10 kA complete including necessry connectionall as specified and directed. 152 Supply and fixed in repairsMCB SPN 32 Amps,C curve 10kA, 240 Volts and to be housed in DBscomplete including necessry connectionall as specified and directed. 153 Supply and fixed in repairs MCB SPN 40 to 63 AMP,C curve 10kA, 240 Volts and to be housed in DBscomplete including necessry connectionall as specified and directed. 154 Supply and fixed in repairs MCB SP 6-32 Amps,C curve 10kA, 240 Volts and to be housed in DBscomplete including necessry connectionall as specified and directed. 155 Material andlabour for earthing complete with Galvanised steel earth plate electrode 600x600x6 mmmm buried directly in ground (Earthpit not less than2.25m below ground level) with top edge of theplate not less than 1.5m below normal groundlevel, connected to GI wire 4 mmasearth lead by means of bolt, nuts, check nutsandwashers of galvanised iron or steel, upto 7.5mlength, earth strip protected by andincluding 15 mm diaGI pipe (light grade) andconnected to main test point or body of pole/pannel or lightening arrester of main controlling switch as directed including concrete pit in PCC(1:3:6)type C1 , Precast RCC(1:2:4)TypeB1 coverslab of size 54x54x5 cm reinforced with 8 mm dia TMT bars @ 100mm C/C bothwayswith onehandle for lifting made out of 10 mm dia TMT bar embedded in precast cover slab, funnel, wire mesh, 20 mm boreGI Pipe (Medium Grade) for watering, Charcoal andsalt in alternate layers of 15 cm (Compacted Thickness) around the earth electrode including necessary excavation, earth work in any typeof soil anddisposal of spoil to a distance n.exc50 m andnecessary testing complete all asshown in Electrical Plate No 3 of SSRPart-I.NOTE : 1. The unit rare includes for protectionh GI pipe of 15mm and watering pipe of 20mm bore including excavation for earth pit in any type of soil/disintegrate rock. 2. Contractor has to bring agriculture soil from outside of defence land and fill in earth pit to acheive desired result as the soil resisitivity is very high. 3. The cost of GI wireincluding protection pipe,from top of earth plate upto 7.5 meter above/below ground level is deemed to be included in the unit rate. 4. All the joints in GI wire and connectgion with earth plate to be welded through brazing and in addition by providing double brass nut bolt and washer. 5.Costing of welding and nut bolts are deemed to be included in the unit rate 156 Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) after taking down old U/S fan complete all as specified and directed . (Note : The existing fan shall be deposited in MES store yard) 157 S&F storage type water heater 25 Ltrs capacity BEE 5 Star rated with all connecting items including necessary electric connection all as directed by Engr-in-Charge 158 M&L cutting holes (round type/square shape) suitable for exhaust fan 300 mm sweep andincluding making good all disturbed surfaces to match the existing positon and two coats colour distemper complete all as specified and directed. 159 Taking down/out unserviceable UG Cables of any Cross Sectional Area and Connections including Bricks, GI Pipes, etc. of any descriptions, laid in Trenches and/or fixing with Walls/Poles including Segregating of Serviceable Materials viz Bricks, Cables, GI Pipes, etc. and keep in Safe custody for re-use, complete all as specified and as directed 160 Excavating in trenches , n.exc 1.5 m wide and n.exc 1.5 m depth for foundation etc or for shafts, wells, cesspits ,manhole pier hole, laying of cables, pipes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in any kind of soilNote : Manual excavation to be done. During excavation if any damage occured to existing cable any type/ water pipe line, it will be contractor responsibilty to get it repair and make functional by providing jointing kit etc without any extra cost. Contractor has to repair it within 24 hrs so that essential service can not be effected due to such damage.If contractor fails to repair it within 24 hrs penalty @ Rs 500/- will be charged to contractor. In this GE decision will be final, conclusive and binding. 161 Returning, filling in, including spreading, levelling, and well ramming in layer not exceeding 25 cm thick in soft/loose soil complete all as specified and directed. 162 Removing excavated material (soil) to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed. 163 Supply, Laying,testing and connecting XLPE sheathed,PVC insulated screened PVC bedded,galvanised steel strip of wire armoured electric power cable heavy duty with solid aluminium conductor 1100 volt grade of size 3.5 core 35 sqmm. , laid in trenches/surface of wall/in GI pipe along with pole for connection to OH lines,includingBrass Compression Cable Gland, Terminal Lugs,clamps,nut & bolts etc all as specified 164 M&L Sand Cushioning (dry) in Trenches for protec-tion of UG Cables (below, above and around the UG Cable laid in Trenches) of 230mm Spread thick -ness and consolidated (punned) upto 180mm thickness, complete all as specified and as directed. (NOTE : For the purpose of Payment, Punned thick-ness of Sand Cushioning only shall be Measured and Paid ). 165 M&L sub class B bricks locally availableof size 25 x 12.5 x 7.5 cm laid dry width wise across the line of cable in trenches for protection of UG cable complete. 166 Supply and fixing/laying50mm bore, steel tubings,galvanised, light grade with all fitting laid across road , in trenches or across PCC drain oralong electric pole or floor/wall etcfor protection of cablecomplete all as specified and as directed. 167 M & L for Boring of horizontal hole under road, pavement, hardstanding by trenchless technology using ultra sound technique and necessary machine with and including GI Pipe light grade of dia 100 with all fittings, for passing of cablecomplete all as specified.Note : (i) One run of boring of horizontal hole and one run of GI Pipe light grade of dia 100 with all fittings will be measured as one unitlength.(ii) All the precaution to be taken by the contractor before drilling the bore. The contractor has to take plan of existing cables any type and pipe line in existing area before drilling the bore.(iii) Any damage to existing cables any type and pipe line in the way of drilling the bore will be repaired and make good by the contractor. No extra cost will be paid on this account.(iv) Contractor has to get the survey of route, length and depth for boring before quoting the rate. 168 Supply and laying Laying DWC HDPE pipe for LT Cable protection double wall corrugated (inner wavy 450N) Size of 63mm complete all as specified and directed by engr-in-charge. 169 Taking up or own carefully steel tubing upto 25 mm bore with all fittinge from in ternches, wall, floor & ceiling and kept in safe custody at site for refixing complete all as specified and as directed. (Note: Excavation and earthwork will be measured and paid separately) 170 Supply & fix in 25mm bore GI tubing medium grade in trenches / Floor / pillar connetion in new postion including fittings all as specified & as directedincluding taking down old unseviceable pipe (Make: Bansal , Jindal) 171 Refixing serviceable steel tubing including cleaning and connections in new or old position (in trenches, on wall/ceiling & floors etc) of 25 mm bore GI pipe with new GI fittings complete all as specified and directed . 172 Supply and fix25 mm bore dia pipe gun metal globe or gate valves, yoke type, full opening with iron wheel head, screwed both ends heavy duty, ISI marked complete for iron pipes complete all as specified and directed. 173 S & F in repairs rotational moulded polyethylene ISI marked (vertical cylindrical with close top) as per IS 12701: 1996 of 1000 litres capacity hoisted and fixed in position with and including Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for 25mm bore dia iron pipe, provision of 25 mm dia medium grade GI pipe for connecting inlet, outlet, over flow and washout pipes including dismantling the existing one and removing to store complete all as specified and as directed.
