Tender For Special Repair Of Single Jcos Living (Np-06) Of Certain Mil Unit And Special Repair To Building No P-08 (Bqm Store) Of Certain Mil Unit Under Ge (S) Binnaguri.; 1 Dismantling Asbestos cement (corrugated,semicorrugated, etc.) sheets in roof coverings complete all as specified. 2 S&F pre-painted galvalume aluminium zinc coating GI based Corrugatedsteel sheet 0.50mm thick of an colour having tensile strength of 550mpa as in roof covering fixed with self tapping screws/J hooks complete all as specified. 3 S&F for pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550mpa as in roof covering fixed with self tapping screws/J hooks complete all as specified. 4 Dismantling wall and ceiling board (fibre pulp, insulation etc) or insulation boards any thickness including cover fillets complete all as specified 5 Supply and fixing aluminium anodised snap grid (605X605mm size) to support the boards / tiles with aluminium Tee section 35 mm x 25 mm x 1.40 mm, cross Tee 23.50 mm x 23.50 mm x 1.40 mm and aluminium angle 25 mm x 25 mm x 1.40 mm as on edge / sides including proper hanging arrangement with 4 mm dia anodized galvanised iron wirewithfalse ceiling of4 mm thick E board classic for insulation and accoustic purposes of size 600X600 mm fixed with necessary accessories to frame work or with staples on snap grid upto ceilingproper scafolding arrangementsandwithcomplete all as specified. 6 -----Blank----- 7 Dismantling floor hearth or wall tiling including cement mortar bedding (incl backing) removing serviceable tiles to store and rubbish off the premises complete all as specified. 8 M&L for joint freenon-skid ceramic tiles any selectedcolour(600x600x7 to 8 mm thick)tiles set and jointed in neat cement slurry pointed in white or coloured cementto match with shad of tile laid and including over 15mm thick screed bed in CM(1:6) complete all as specified 9 Ditto as per serial item No 8 described here-in before buton vertical surfaces as in skirting over10mmthick rendering in CM (1:4) complete all as specified. 10 M&L for non-skid ceramic coloured (400x400x7 to 8 mm thick)tiles set and jointed in neat cement slurry pointed in white or coloured cementto match with shade of tiles laid over and including15mm thick screed bed in CM(1:6) complete all as specified. 11 M&L for glazed colouredceramic tiles (350x450x7mm thick)on vertical surfaces such as skirting/dado set and jointed in neat cement slurry pointed in white or coloured cement to match with shade of tile laid over and including 15mm thick rendering in CM(1:4) all as specified. 12 Taking down cement plaster any description on brick or stone wall etc including racking out joints hacking for key scrubbing down with water etc complete all as specified 13 M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar (1:6) finished even & fair complete all as specified. 14 M&L for rendering 20mm thick in cement mortar 1:4 in two layers of 10mm each using WPC in finishing layer on brick or concrete surfaces finished even & fair (WPC for finishing layer shall be paid seperately as supply only) complete all as specified 15 Supply only liquid water proofing compound complete all as specified. 16 M&L for prepartion of newly plasteredsurfaces of walls and applying two coats of oil bound distemper over a coat of primer after applying 2 coats ofcement based wall putty 1 mm thick (average thickness) eachto wall surface complete all as specified 17 M&L for applying two coats of weather proof exterior emulsion paint of standard quality and make ,over a coat of white primer including preparation of newwall surfaces complete all as specified 18 M&L for complete removal of existing treatment of old plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer after applying 2 coat of cement based wall care putty 1 mm thick (average thickness) eachincluding complete removal of existing treatmentcomplete all as specified 19 M & L for complete removal of existing treatment and finishing the walls with two coats Acrylic smooth exterior emulsion paint of required shade for New work over and including priming one coat of exterior primer applied all as per manufacturers specification and as specified. 20 Taking down chowkats or frames exc 1.5 Sqm and n.exc 4 Sqm (without taking off shutter from the frames) and removal from site complete all as specified. 21 Ditto as per serial item No 20 described here-in before but n.exc 1.5 Sqm each complete all as specified. 22 S&Fpressed steel frames for doors with one or more rebates including necessary lugs, hinges, lock strike plate, etc., complete, as specified, size of frame 125mmx 60 mm x 1.25mm (thick) complete all as specified 23 S&F for plain, framed, factory made panelled shutters 35 mm thick (any number of panels) , with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers; supplied and fitted to chowkats complete all as specified. 24 S&F second class hardwood, factory made glazed and skelton shutters 35 mm thick open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part-I Section8, Clause 8.20 (a) suppliedand fitted to chowkats complete all as specified. 25 S&F in repair factory made steel windows with side hung shutters openable type including friction/projected typehinges steel handle and peg stay complete withoutglazing bars fixed to existing opening and making to match as per existing surfaces complete all as specified. 26 S&F in repairfactory made steel windows with side hung shutters openable type including friction/box type hinges steel handle and peg stay complete with glazing bars fixed to existing opening and making good to match as per existing surfaces complete all as specified. 27 S&F in repair factory made steel ventilator with top hung shutter including friction/ box typehinges ,steel peg stay complete and making good to match as per existing surfaces etc complete all as specified. 28 S&F Framed work such as grills,gratings, etcwith ends of bars shouldered and/or riveted,or forged into spikes; framedguard bars; barred iron doors; ladders; framed balusters; walkways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 29 M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10cm width or girth complete all as specified 30 M&L for two coats of synthetic enamel painting to new wooden surfaces over a coat of pink primer including preparation of surfaces area exc 10cm width & girth complete all as specified. 31 S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing specified in SSR Part-II complete all as specified 32 S&F Solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as per specification and drawing on specified in SSR Part-II complete all as specified 33 S&F for 150 mm size aluminium anodised cast type handles complete all as specified. 34 S&F 150mm long aluminium anodised,barrel tower bolt of extruded section complete all as specified. 35 S&F 250mm long aluminium anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section complete all as specified. 36 S&F 100mm size mild steel butt hinges medium weight complete all as specified 37 S& F 140 mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified 38 M&L for providing plain cementconcrete type C-1, 1:3:6, (using 20 mm graded stone aggregate), as in copings, bed block for filing hollow space of steel chowkhats, fixing of hold fast, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified 39 S&F 4mm thick sheet glass panes ordinary quality n.exc 0.5sqm each fixed to steel frame complete with oil putty in square including steel pin complete all as specified. 40 S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed with tinned tacks,or stainles steel wire staples complete all as specified. 41 Dismantling of timber scantling 40 sqcm and over in section in any position complete all as specified 42 M&L for mild steel rolled sections conforming to Fe - 410 (Gde E-250) as in main and cross beams, hip and jack rafters;verticals , purlins where connected to common rafter and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified. 43 S&F in repair vitreous china washbasin, white flat back, size 550x400mmincluding brackets,cutting for and pinning in ends of brackets or erecting stand , 32 mm dia of discharge pipe,Waste coupling of PTMT (half or full threaded)complete all as specified 44 S&F in repairWater Closet (squatt pattern) of vitruous china squatting pan of pattern ORRISA pattern size 580 x 440 mm white with integral foot rests (excluding flushing cirstern and flush pipe) including connection to trap and flushing pipe anti syphon pipe etc complete including trap set in and incl concrete complete all as specified 45 S&F in repair of PVC low level flushing cistern, 10 ltr capacity, syphonic action type white body with inlet ball valve, float , handle,bracket, longflush pipe of PVC to suit flushing cistern ( long bend) etc complete & connecting to WC complete all as specified 46 S&F 600 x 450mm bevelled edge mirror of selected quality glass mounted on 6mm thick AC bldg board or commercial plywood and fixed to wooden plug with chromium plated brass screws & cup washers complete all as specified. 47 S&Fin repair of PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified. 48 S&F in repair15 mm bore fancytype pillar taps, cast copper alloy with capston heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe 15mm bore complete all as specified. 49 S&Fin repairs bib taps 15mm bore fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified 50 S&Fin repair PVC floor trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1(diameter of outlet100mm) complete all as specified 51 S&F in repair swivel shower of CP with shower arm 150 mm size for fixing with 15 mm bore GI pipe complete all as specified. 52 Supply & fix in repairangular stop cock made of brass chromium plated screwed both ends for iron pipe for 15mm bore complete all as specified . 53 S&Ftubular towel rail 20mm dia D type, Brass Chromium Plated 60 cm long between flanges complete all as specified. 54 Taking up or downsteel water tubings and fittings etc complete and makinggood disturbed surfaces of walls/ceilings etc complete all as specified following:- 55 Bore tubing 15mm 56 Bore tubing 20mm complete all as specified. 57 M & L for steel tubing medium grade,galvanised withall fitting fixed complete to walls and ceiling or floor complete for this following:- 58 Bore tubing 15mm complete all as specified. 59 Bore tubing 20mm complete all as specified. 60 Demolition of brick wallingbuilt in cement mortar etc complete all as specified. 61 M&L for brickwork with burnt fly ash old size bricks straight or curved on plan exc 6mtr mean radius built in cement mortar 1:6 by using old size bricks complete all as specified.. 62 Material and labour for hoisting and fixing rotational moulded polyethylene(double layer) water storage tanks 1000 lit capacity (Cylinderical vertical), ISI marked(IS-12701:1996) hoisted and fixed in position including inlet, oulet, over flow connection, ball valves etc and including takindg down old one complete all as specified. 63 Supply and fix in repair PVC (SWR) pipes 110mm dia,type A conforming to IS, single socketed,in anylength with rubber ringjointslaid in trenches or floor complete all as specified. 64 S&Fin repair for 110 mm bore PVC (SWR) bends any radius fixed to PVC Pipes/Steel Gutters etc complete all as specified 65 S&F in repairfor PVC (SWR) 110 mmvent cowl fixed to PVC Pipes etc complete all as specified 66 Demolition of cement concrete (Reinforced) of any description in any position not otherwise specifically provided for complete all as specified. 67 M & L for RCC (Nominalmix) 1:1.5:3 type A1(using 20 mm graded stone aggregate) as in Beams, cantilevers, lintels over 1.5 M span.complete all as specified. 68 Use and waste of form work to sides and soffit of beams, lintels,shelves of slabs/beams and similar works including supports, over hangs etc rough finished surfaces of concrete,flat.etc complete all as specified. 69 M & L for TMT bars 10mm dia & over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mm dia or secuiring with clips equality conforming to TMT bars complete all as specified. 70 Ditto as per serial item No 65 described here-in-before but 6 to8 mm dia as in stirrups complete all as specified. 71 Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided complete all as specified. 72 M&L for 75mm thick PCC type C-2 (1:3:6) (using 40 mm graded stone agg) as in plinth protection path/hardstanding finished cement concrete surfaces fair and even complete all as specified. 73 M&L for hard core of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified. 74 M&L for 80 mm thick M-35 grade factory made vibratory compacted cement concrete rubber moulded, interlocking paver block any shape and size confiroming to IS 15658-2006 with grey cement and pigment as approved laid over and incl 25 mm thick consolidated sand cushion and joints filled with sand complete all as specified. 75 S& F in repair curtain rod,20mm dia mild steel, chromium plated with fixing brackets, stops,etc. complete all as specified. 76 Removing existing water proofing treatment to complete any descrption/any thickness and in any position including removal of rubbish of the premises etc complete all as specified. 77 M&L for cement concrete type Bo 1:2:4 (using 12.5mm graded stone aggregate) 25mm thick as in roof to achieve slope on existing roof surface complete all as specified. 78 M & L for water proofing treatment to RCC roof slab as specified below complete all as specified.(a) 10 mm thick cement plaster in CM 1:4 with integral WPC to be laid over the RCC roof slab when the concrete is green.(b)Applying a uniform coat of bitumen primer @ 0.70 kg/sqm over cement plaster.(c)3 mm thick plain texture and weighing not less than 3.5 kg/sqm Atactic Polypropylene Polymer (APP) modified bitumen based prefabricated five layer water proofing membrane reinforced with non woven polyster matt black finished over compatible primer at 0.4 Ltr / sqm of density at 25 degree centigrade 0.87 - 0.89 kg/ltr and viscosity 70-160 cps or cold sticker and torch application of membrane with overlap while torching shall be 150 mm on length side and 100 mm on width side. after necessary preparation of surface complete as per manufacturers instructions.(d) Apply two coats of bitumastic - aluminium paint over the membrane. 79 M&L for cement concrete type B1,1:2:4 (using 20mm graded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified.. 80 Demolition of cement concrete (un reinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified. 81 M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base 15mm thick in cm 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified. 82 M&L for 25 mm thick cement concrete type B1, 1:2:4 (20 mm graded aggregate) as in floor etc and finishing cement concrete completeall as specified. 83 M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with ditto as per item78 above complete all as specified. 84 M&L for PCC 1:2:4 type B-I ,(using 20 mm graded stoneaggregate) as. in coping /benching to sides of foot pathfininished fair and even including necessary formwork etc complete all as specified. 85 -----Blank----- 86 -----Blank----- 87 M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces of walls in cement morter 1:4 with water proofing compound finished even and fair complete all as specified.(Note : WPC shall be measured and paid separetely) 88 M&L for rendering 5mm thick in CM (1:3) on fair faces of concrete surfaces as in celling finished fair and even without using extra cement complete all as specified. 89 M&L for preparing of new plastered surfaces of wall (Internal & external) and applying two coats of cement based wall care putty including preparation of surface to receive finishes (primer, distemper, paint etc.) complete all as specified 90 M & L for preparing new Plasteredsurfaces of walls and finishing the walls with Acrylic smooth exterior paint of required shade for New work Two or more coats applied over and including priming one coat of exterior primer applied complete all as specified . 91 M&L for prepartion of newly plasteredsurfaces of walls and applying two coats of oil bound distemper over a coat of primer to wall surface complete all as specified. 92 M&L for preparing newplastered surfaces and applying three coat of white wash on ceilingcomplete all as specified. 93 M&L forapplying two coat of acrylic -based distemper of shadeas approved by GE over a coat of primer over finished putty surface on decorated old wall complete all as specified. 94 M&L for preparing oldplastered surfaces and applying two coat of white wash on ceilingcomplete all as specified. 95 M&L forplain cement concrete1:3:6type C-2(using 40 mm gradedstone aggregate ) as insurface channels and drains etc complete all as specified. 96 Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etccomplete all as specified 97 -----Blank----- 98 M&L preparing old painted steel surface of any description not otherwise described for over 10 cm width or girth and applying one coat of synthetic ennamel paint complete all as specified. 99 S&F for pressed steel frames for doors with one or more rebates including necessary lugs, hinges, lock strike plate, etc., complete, as specified, size of frame 105mm x60 mm x 1.25mm (thick)complete all as specified 100 S&F 30mm thick factory made flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides kiln seasoned and chemically pressure treated complete all as specified. 101 -----Blank----- 102 M&L for preparing old painted wooden surface of any description not otherwise described for over 10 cm width or girth and applying one coat of synthetic ennamel paint complete all as specified. 103 Demolition & breaking up drain pipes( salt glazed ware, AC or reinforced concrete) set in cement mortar, internal dia of pipe 150mm complete all as specified. 104 Excavation in trenches n.exc 1.5 in deep and n.exc 1.5 m wide for foundation etc not exc 10 sqm on plan and getting out in soft / loose soil complete all as specified. 105 M&L for precast RCC (1: 1.5 :3) type A-1 (using 20mm graded stone aggregate) set in cement mortar 1:4 as in manhole covers including necessary use and waste of formwork complete all as specified. 106 S&F PVC (SWR) (Bore of pipe 160mm) pipes with working pressure 6 kg/cm2 single socketed, in any length with rubber ring joints fixed to walls with necessary clamps, bolts etc complete all as specified. 107 S&F PVC (SWR) bends any radius fixed to PVC Pipes/Steel Gutters etc complete all as specified. (Bore of bend 160mm) 108 M&L for mild steel TMT bars 6mm to 8mm dia cut to length , bent to shape required,including cranking , bending and binding with MS wire , not less than 0.9 mm dia or securing with clip complete all as specified.. 109 M&L for PCC 1:3:6 type C-2 (40mm graded aggregate) as in foundations, filling and mass concrete complete all as specified. 110 M&L for 15 mm thick plastering in cement mortar 1:3 on fair faces of brick or concrete surface finished even & smoothwithout using extra cement complete all as specified. 111 M&L for PCC (1:3:6) type C-2 (using 40mm graded stone agg) as in concrete bed to drain pipes including packing under & haunching against the sides of pipes after they are laid & tested dia of pipe 150mm bore complete all as specified. 112 Returning ,filling in , including spreading , levelling , watering and well ramming in layer not exceeding 25 cm thick in soft/ loose soil complete all as specified. 113 Removing excavated material ( soils) not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified. 114 M&L cutting into existing manhole for connecting new drains making good to pipe and rendering cutting out existing benching for & forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished & reforming benching as required dia of pipe 150mm bore complete all as specified. 115 Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified. 116 M&L for point wiring complete with 1.5 Sqmm multistranded copper conductor single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit not less that 20mm dia and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 Sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI marked) as earth continuity conductor connected to common earth dolly, fabricated sundn terminal box made out of GI sheet steel not less than 1.22 mm thick for boxes upto a size of 200 x 300mm and above this size not less than 1.63 mm thick duly painted with aluminum inside and anticorrosive paint outside, concealed in walls, with 3mm thick bakelite/plastic laminated sheet top cover fixed with cadmium plated iron screws (or provision of modular sunken box, modular back plate and top cover for housing of modular switch,socket, regulators etc as per site requirement) for housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for conduits and sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications.Connections of cable with MCBs or bus bar shall be done through proper size copper/brass thimbles. Where concealing of conduit is not feasible ie on surface of roof etc, conduit shall be fixed on surface with necessary saddles at no extra cost all as specified and as directed for the following :- 117 One light point controlled by one, one way switch 5/6 amps complete all as specified. 118 One ceiling fan/Exhaut fan point controlled by one, one way switch 5/6 amps complete all as specified.. 119 One socket out let 5/6 amps point on the same board complete all as specified. 120 One socket out let 5/6 amps point on the independent board complete all as specified. 121 Ditto as per serial item No 112 described here-in-before but wiring with 2.5 sqmm single core copper conductor for one socket out let 15/16 amps point on the independent board complete all as specified. 122 S&F switch piano flush type 5/6 amps single pole one way complete all as specified. 123 S&F socket 2 in 1, 5 Pin, 5/6 amps, white ivory finish flash type complete all as specified. 124 S&F of socket outlet 2 in 1, 5 Pin, 5/15 amp,multipurpose 230 volt flash type complete all as specified. 125 S&F switch piano flush type 15/16 amps single pole one way complete all as specified. 126 S&FCeiling rose, surface type with back plate, three terminal /PVC/ polycarbonate, isolated body complete all as specified. 127 S & F step type electronic fan regulator having min 80 watt capacity 230 volt 50 Hz rotary step white/ivory finish complete all as specified. 128 S&F, IP 20, class I, LED tube light fittings 20W (or nearest next higher wattage) (4feet), wall/ surface mounted, integrated type with aluminium housing and decorative and caps with integrated high efficiency electronic driver and surge suppressor of 5KV or more, luminaire efficiency > 120 lumens/watt, power factor > 0.90, operating range - 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/ square blocks, screws etc complete with all accessories internally prewired and connecting up with complete all as specified. 129 S & F LED street light fittings 35 watt (or nearest next higher wattage) with high efficiency electronic driver and surge suppressor 7.5 KV, 120 lumen/watt, power factor > 0.90 voltage operating range 150 to 270V, 50 Hz with high pressure die cast aluminium housing, heat resistant, toughned glass cover with IP66 protection complete all as spedified. 130 S&F Sheet metal enclosure for 8 way Distribution Boards (DB’s), double door, single pole & neutral with din rail, IP-20 protection suitable for fixing MCBS/lsolators completeincluding provision of blanking plates as required and taking down the old one complete all as specified. 131 S&F Sheet metal enclosure for 4 way Distribution Boards (DB’s), double door, single pole & neutral with with din rail, IP-20 protection suitable for fixing MCBS/lsolators completeincluding provision of blanking plates as required and taking down the old one complete all as specified. 132 S&F MCB, Single pole & neutral 6 to32 amps, 240 volts, ‘C’ curve, 10 KAall completeincluding taking down the old one complete all as specified. 133 S&F MCB, Single pole, 6 to32 amps, 240 volts, ‘C’ curve, 10 KAall completeincluding taking down the old one complete all as specified. 134 M &L for Earthing complete with GI earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25M deep below normal ground level) with top edge of the plate not less than 1.5m below normal GL. Connected to galvanized earth lead wire 4mm dia by means of nut, bolt, check nut and washersincluding necessary excavation and earth work in soft/loose soil, GI protection pipe light grade 15mm bore for protecting the GI wire mesh funnel alternate layer of charcoal dust, and saltPCC pit 1:3:6 type C1 using 20mm graded stone aggregate and 50mm thick RCC 1:2:4 type BO using 20mm graded stone aggregate cover re-inforced with 8 mm dia MS TMT bars 80mm C/C both ways complete all as specified and shown in Electrical plate No.3 SSR part-1 and connected to the earth point and testing complete including taking out the old one complete all as specified. 135 M&L for street light bracket made out of GI pipe light grade 32 MM dia 1.2 mtr length bent to shape and reduced to required size at top upto 1.2 mtr length by cutting, welding and well finishing including MS clamp of flat iron of size 25 x 5 mm suitable length 2 Nos complete with drilling hole, fixing with runts bolts and washers including painted with two coats aluminium paint over a coat of red oxide primer complete all as specified.. 136 M&L for Sub main wiringconcealed type with two run single core cable PVC insulated cable with4.0Sqmm (Nominal area) multi stranded copper conductor FRLS cable 1100 volts gde incl earth continuity conductor using PVC insulatedcable of stranded copper conductor of size 4.0 Sqmm connected to common earth dolly anddrawing into rigidPVC conduitsof 25 mm dia medium gradesize,making good the disturbed surfacescomplete including taking down old submain wiring.(NOTE : Two run of submain wiring cable alongwith one run of earth wire and one run of PVC conduit shall be measured as one length complete all as specified. . 137 Taking down ceiling fan sealing cable end, dismantling blades and removing fan and blades to storeand refixing the same after duly paintaing of fans and after B/R workincluding provision of 3 core flexible copper wire of size 0.75 sqmm complete all as specified.Note: Cost of painting shall be paid under separate items of BOQ 138 Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 2 core all fixing and connecting accessories such as cable lugs, cable glands, nut, bolts, complete all as specified. 139 M&L for sand cushioning in cable trenches over & under the cable, with river washed coarse sand, as per standard practice with proper compaction complete all as specified. (Punned thickness upto 18 cm shall be considered for payment as per para 19.75 of SSR Part-I) 140 Supply and layingbrick for protection of cable over sand cushioning cables inside the trench by using common brunt clay building bricks sub-class “B” old size brick and flat and width wise along the axis of the trenchcomplete all as specified. 141 Supply and lay pipe galvanized of 25 mm dia, “Medium grade”, including fittingsand taking out old one complete all as specified. 142 Supply and fix Gun metal ,globe Gate Valves with iron wheel head of 25 mm dia bore complete with all accessories all as specified. 143 S&F LED Bulk Head lights fitting 1x 9/10W, 220V AC integrated high efficiency electronic driver and surge suppressor of 4KV or more, luminaire efficiency not less than 120 lumens/watt, power factor not less than 0.90, CRI 80, THD 10%, operating range - 140 to 270 V, 50 Hz fixed etc connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.complete with all accessories internally prewired and connecting up with complete all as specified. 144 M & L for painting of ceiling fans of any make/model and size complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc.complete all as specified by Engr in charge 145 Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified 146 Supply, laying, jointing & testing in trenches or passing through pipe, 1100 volts grade, XLPE insulatedPVC bedded, galvanized steel strip or wire armoured LT electric power UG cables, heavy duty with stranded aluminium conductor of cross sectional area25 Sqmm 2 core with and including all fixing & connecting accessories such as Aluminium cable lugs, cable gland, nut, bolts, washer etc complete including taking out old unsv cable as specified.(NOTE: Earthwork & Excavation, GI pipe, bricks for protection etc shall be measured and paid separately under relevant items of this schedule A). 147 M & L for horizontal boring across the existing road without disturbing the road surface for insertingGI pipe complete all as specified. Note :- (i) Removal of surplus soil shall be deemed to be include in the unit Rate. (ii) GI pipe will be measured and paid separately under relevant item of Sch A. 148 M&L for 40 mm bore steel tubing light grade ISI marked for protection of cable including necessary joints complete all as specified.
