|
| 1 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 2 | 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws |
| 3 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws :30 mm thick shutters.with ISI marked M.S. pressed butt hinges bright finished of required size,. Kiln seasoned and chemically treated hollock wood |
| 4 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete (Copper oxidised as per IS 1378)300x16 mm |
| 5 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS 1378). 250x10 mm |
| 6 | 100x10 mm |
| 7 | Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete (Copper oxidised as per IS 1378), 125 mm |
| 8 | 100 mm |
| 9 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. |
| 10 | Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets :25 mm dia (heavy type) |
| 11 | 12 mm cement plaster of mix :1:6 (1 cement: 6 coarse sand) |
| 12 | Rough cast plaster upto 10 m height above ground level with a mixture of sand and gravel or crushed stone from 6 mm to 10 mm nominal size, dashed over and including the fresh plaster in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand) and top layer 10 mm cement plaster 1:3 (1 cement : 3 fine sand) mixed with 10% finely grounded hydrated lime by volume of cement. |
| 13 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 14 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound ) content less than 50 gram/ litre, of approved brand and manufacturerincluding applying additional coats wherever required to achieve even shade and colour (Apolite premium (asian), Shilk (Burger), Beauty Gold/Impression(Nerolac),or equivalent) |
| 15 | Finishing walls with Acrylic Smooth exterior paint of required shade : (Apex Ultima (Asian), Weather coat anti dust (Burger), Excel (Nerolac) or equivalent)...Old work (one or more coats applied @ 0.83 ltr/10 sqm). over existing cement paint surface |
| 16 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Asian( Apcolite premium Gloss Enemal), Nerolac (Synthetic enamel Hi Gloss), Burger (Luxol Higloss) or equivalent),, One or more coats on old work |
| 17 | Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead |
| 18 | Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5sqm and under, including cutting the patch in proper shape, rakingout joints and preparing plastering the wall surface with white cementbased polymer modified self curing mortar, including disposal ofrubbish, all complete as per the direction of Engineer-In-Charge. |
| 19 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lea |
| 20 | Renewing glass panes, with putty and nails wherever necessaryincluding racking out the old putty:Float glass panes of nominal thickness 5 mm(weight not less than 12.5kg/sqm) |
| 21 | Demolishing cement concrete manually/ by mechanical meansincluding disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 22 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 23 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding pointing the joints with white cement and matching pigments etc., complete. |
| 24 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.10 litre capacity - White |
| 25 | Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan. |
| 26 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Semi rigid pipe, 32 mm dia |
| 27 | Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in Charge. |
| 28 | Providing and fixing kitchen sink including making all connections excluding cost of fittings.White glazed fire clay sink of size 600x450x250 mm |
| 29 | Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour.Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms |
| 30 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 31 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 32 | Providing and fixing brass stop cock of approved quality :15 mm nominal bore |
| 33 | Providing and fixing brass stop cock of approved quality :20 mm nominal bore |
| 34 | Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required :20 mm nominal bore |
| 35 | Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required :25 mm nominal bore |
| 36 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore |
| 37 | 25 mm nominal bore |
| 38 | Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length, 20 mm nominal bore |
| 39 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :15 mm nominal bore |
| 40 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore |
| 41 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. |
| 42 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. |
| 43 | Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball.20 mm nominal bore, 105 mm long, weighing not less than 138 gms |
| 44 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931..15mm nominal bore |
| 45 | Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead 75 to 80 mm dia pipe |
| 46 | Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I. rain water pipes embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the walls etc. 100 mm diameter: |
| 47 | Providing lead caulked joints to sand cast iron rain water pipes and fittings:100 mm dia Pipe |
| 48 | Providing, fixing and embedding sand cast iron accessories for rain water pipes in the masonry surrounded with 12 mm thick cement mortar of the same mix, as that of masonry (lead caulking will be paid for separately):Sand cast iron plain shoes : 150 mm diameter |
| 49 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter |
| 50 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Coupler..110 mm |
| 51 | Single pushfit Coupler.. 110 mm |
| 52 | Single tee with door, 110x110x110 mm |
| 53 | Single tee without door,, 110x110x110 mm |
| 54 | Bend 87.5°,, 110 mm bend |
| 55 | Shoe (Plain),, 110 mm Shoe |
| 56 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 57 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etcInternal work - Exposed on wall,, 20 mm dia nominal bore |
| 58 | 25 mm dia nominal bore |
| 59 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore |
| 60 | 25 mm nominal bore |
| 61 | Supplyingand fixingfollowing piano type switch / socket on the existing switch box / cover including connections etc as required ,, 5/6 amps switch |
| 62 | 15/16 A Switch |
| 63 | 3 pin 5/6 A Socket outlet |
| 64 | 6 Pin 15/16 A Socket outlet |
| 65 | Supplying and fixing following modular switch / socket on th existing modular plate & switch box including connections but excluding modular plate etcas required ,, 5/6 A Switch |
| 66 | 15/16 A Switch |
| 67 | 3 Pin 5/6 A socket outlet |
| 68 | 6 Pin 15/16 A Socket outlet |
| 69 | Supplying and fixing PVC batten / angle holder including connections etc as required |
| 70 | Providing and fixing 18 watt Led tube ligth 1800mm long |
| 71 | Providing and fixing ceilling fan 1200mm |
| 72 | Supplying and fixing call bell/ buzzer suitable for single phase,230 V, complete as required. |
| 73 | Providing and fixing exhaust fan 450mm |
| 74 | Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes. |
| 75 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as requiredSingle pole |
