Tender For 4. Construction Of A New Veterinary Hospital Building At Mauje Parinche, Taluka- Purandar - Excavationforfoundationinearth,soilsofalltypes,sand,gravelandsoftmurum, includingremovingtheexcavatedmaterialuptoadistanceof50metresbeyondthe building area and stackingandspreadingasdirected,dewatering,preparingthebed forthefoundationand necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5m to 3.0m) By Mechanical Means 2 Excavation for foundation in Hard rock by blasting including trimming and leveling the bed bychiselingwherenecessaryandremovingtheexcavatedmaterialandstacking itin measurable heaps within a distance of 50 metres from the building area including dewateringand back filling with available earth/murum, watering, ramming, etc. complete.(Liftupto 1.5m) By Mechanical Means 3 Providing solingusing 80 mmsize trap metal in 15 cm. layer including filling voidswith Crushed sand/grit, ramming, watering etc. complete. 4 Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)(Non SCADA Item) 5 Providing and laying in situ /Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering formwork, laying/pumping cover blocks, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) (Non SCADA Item) 6 Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)(Concrete Non Scada) 7 Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite/quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)(Non SCADA Item) 8 Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)(Concrete Non Scada) 9 Filling in plinth and floors with contractorsmaterial/brought from outside and approved byEngineer inchargein layers of 15 cmto 20 cm including watering andcompactionetc. complete. 10 Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. 11 Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in foundations and plinth of inner walls/ in plinth external walls including bailing out water manually , striking joints on unexposed faces, raking out joints on exposed faces and watering etc. Complete 12 Providing first class Brick masonry with conventional / IS. type bricks in cement mortar 1:4 including scaffolding, racking out joints pointing in C.M 1:3 and watering etc. in pillars of curved shapes, as shown on the drawing or as directed etc. complete. 13 Providing and fixing chicken mesh of 22 gauge, with about 30 cm. width at the junction of R.C.C members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete /B.B.masonry and or tying by binding wire etc. complete. 14 Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete 15 Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. 16 Providing and applying Two coats of wall care Putty on plastered surface and Ceiling and Walls to prepare surface even and smooth of approved make, etc complete 17 Providingandapplyingwhite-washintwocoatsonold/newplasteredormasonry surfacesandasbestoscementsheetsincludingscaffoldingandpreparingthesurfacebybrushing and brooming down etc. complete. 18 Providing and applying impression 24 carrat Luxury paint of approved make & approved brand Emulsion paint to interior walls and ceilings of approved quality, colour and shade to new surface in two coats, including sub surface prparation by Acrylic putty and Acrylic primer coats including scaffolding, preparing the surface. etc. complete (Low VOC) 19 Providing and applying two coats of exteriorweather shield paint of approved manufactureand of approved colour to the plastered surfaces including cleaning,preparing the plastersurface,applyingprimercoat,scaffoldingifnecessary,and watering the surface for two days etccomplete. NOTE: ForItem One Number 15 to 18 prior approval of Superintending Engineer will be necessary 20 Providing and laying vitrified matt fininsh tiles having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etc. complete 21 Providing and laying vitrified mirror / glossy finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete 22 Providing and laying Antiskid Ceramic tiles of approved quality of size 30 cm x 30 cm and confirming to IS 15622-2006 (Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete. 23 Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete. 24 Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete 25 Providing and fixing machine cut mirror polished 18 mm to 20 mm thick telephone black granite / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone partition with full moulding the edges etc. complete . Both side polis 26 ProvidingandfixingCountrycutteakwooddoubleorsingleleafsecondclassfully panelleddoorshutterwith35mmthickstyleandrailwith25mmthickpanelswith openable fan light as per detaileddrawings. Excluding the door frame 60mm x 100mm stainless steel fixtures andfasteningandfinishingthewoodworkwithoilpainting3coats.(Excludingthedoor frame) 27 ProvidingandfixingCountrycutteakwoodsingleleafpanelleddoorshutterwithout fanlight and 25mm thick as per drawing consisting ofT.W. top rail size 100mm x 25mm and bottom lockrail200mmx25mminsertpannel12mmthickcommercialply facedT.W.particle board with phenol formaldehyde synthetic resin (Generally confirmingtoISI3097)excludingframe,including stainlesssteel fixtureand fasteningandT.W. beadingtojunctionsof panelled insertsand as instructed by the Engineer in charge including 3 coats of oil painting etc. complete. 28 Providing and fixing solid core flush door shutter commercial in single leaf 32 mmthick without ventilator commercial type of exterior grade as per detaileddrawings with wrought iron hold fast, stainless steel fixtures and fastenings and handles on bothsides and finishing with oil painting 3 coats complete. 29 Providing and fixing of factory made uPVC Sliding window & door (WhiteColour) complete, comprising uPVC multi-chambered frame having in-built uPVC roller track on top and uPVC sash with wall thickness of 2.3mm(+-0.2mm), duly reinforced with G.I.section 1.5mm, wherever required.uPVC window & door profile shall be made in India & shall conform to BSEN 12608 and other standards as mentioned below :S.No. Name of the test Test Method Specified Parameter1Tensile Impact Strength ISO 8256-more than 700Kj/m2 2Vicat Softening Temperature EN ISO – 306 Shall not be < 750C3 Charpy Impact Strength EN ISO – 179-2 Shall not be < 20KJ/m24 Flexural Modulus Elasticity EN ISO – 178 Shall not be < 2200 N/mm25 Mean Breaking Stress for welded corner(a) For the tensile bending test EN – 514 Shall not be < 25 N/mm2 (b) For the compression bending test Shall not be < 30N/mm2 6 Heat Reversion Test IS:4985-2000 Shall not be > 2.0 %7 Surface Spread of flame BS : 476 - Part 7 Classification 1 8 Ignitability Evaluation BS : 476 - Part 5 P Not easily ignitable9 Tensile modulus ASTM D 638 Shall not be < 35 MPa10 Shear Modulus ASTM D 732 Shall not be < 220 MPa 11 Tensile Strength EN ISO 527 Shall not be < 30 MPaAll corners of frame and sash will be fusion welded. After placing 5mm Float Annealed glass in the sash, uPVCglazingbead ,interlock, EPDM/TPEgasket, brush shall be provided including touch lock and rollers & proper drainage system shall be provided. Window/Door will be fixed to the wall with 100mm long and 8mm dia. Fasteners and complete in all respect as per direction of Engineer-In-Charge. uPVC Window and Door Profiles are warranted for a period often (10)years against non-uniform discoloration,wrapping and rotting under general use. A) 2 Track 2 / 4 Sash (Big Series) window frame of size 67 x 54 mm & Sash of size 64 x 47 mm1) First floor 30 Providing and fixing 15 mm dia. screw down bib/ stop tap of brass including necessary socket union nut complete. 31 Providing and fixing divertor with overhead shower,shower arm,spout,hand shower with wall bracket having flow rate up to 12 liters/minutes of Jaquar/Cera/Hindware /Perryware or equivalent make including all necessary pipes,fittings etc.complete as directed by Engineer In Charge.( Make shall conform to manufacturers Green product and shall got approved from the Engineer In Charge.) 32 Providingandfixing WhiteglazedwithbottletrapearthenwareWashHandBasinof 55x40 cmsizeincluding coldwaterpillertaps, brackets, rubberplugs and brass chain, stop tap,chromiumplatebottletrapandnecessarypipeconnectionsincluding UPAC waste pipe and trap upto the outside face of the wall, making good the damagedsurface, testing etc. complete. 33 Providing and laying in trenches 15 mm dai. CPVC pipe including necessary excavation, fittings.Refillingtrenchesetc.completeIncluding removingexisting pipe line ifnecessary and conveying and stacking the same in PWD chowky or as directed etc.complete. 34 Providing,layingandfixingP.V.C.pipeof25mmdia.withfittingssuchasbends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removingexistingpipelineifnecessaryandconveyingandstackingthe sameinPWD chowky or as directed etc. complete. 35 Providing andfixing 10cm C.I.NahaniTrapincludingC.I.gratingbendandpiece ofC.I. pipe upto the outside face of the wall complete. 36 ProvidingandfixingH.D.Pcontaineronepiecemouldedwatertankmadeout of low density polythyler and built corrugation including of delivery up to destination hoistingand fixingofaccessoriessuchasinlet,outletoverflowofall tankscapacityabove 1000 to 20,000 litres 37 Providing and constructing Brick MasonryInspection Chamber 90cm x 45cm x 90cmincluding 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half roundG.S.W.pipes,BrickMasonry,plasteringfrominsideandC.I.lidcoverof 75Kilogramwith lid and frame fixed in cement concrete. 38 ProvidingandlayingcastironpipesofBclassof100mmdiaMetrewithsocketsand spigot ends/ flanges and cast centrifugally/vertically including specials, laying pipes andback filling the trench complete including excavation. 39 Providingandfixing900mmhighS.S.304GradeStainlesssteelrailingwith40mm diaMetre and1.5mmthickattop, 40mm diaMetreand1.5mm thickverticalsupports spaced at 1.5mcenter to center and 8mm thicktoughened glassincluding fabricating ,fixtures, errecting ,necessarywelding,grinding,finishing,buffingto stainless steel pipe etc. complete 40 ProvidingandFixingVerticalBlindsofapprovedMakeandshadeof100mmregular fabric with powder coated aluminium channel with teltingPVC chain & bottom weight plate with all necessary fixtures and fitting etc. complete. (Sample to be final by EngineerIn-charge prior execution of work) 41 ExecutivesTable @ 1800Lx900Dx750HTProviding & Fixing of Table @ 1800Lx900Dx750HT - TOP & GABLE END to be made of Membranefinishwithsoftwaterfalledges&curvedpanel& DecoratedAnodized section MODESTY PANEL to be made of 18 mm thick Prelaminated particle board with PVC edge band as per drawing 42 Credestal @ 1200Lx450Lx650HTProviding & Fixing of LOW HEIGHT CREDESTAL @ 1200L X 450D X 650H:- To be made out of Membrane Finish ( 2 Openable Shutter & 3 Drawer Pedestal in between )as per drawing. 43 Free Standing Table @ 1200Lx600Dx750HTProvidingandfixingTableofSize1200x600x750mm.Top:madefrom25mm PrelaminatedParticleboard. Alledgesarecoveredby2mm.Thk.PVCedgebands glued by hot melt glue applied by auto edge banding machine.Legs : C Shape made from CRCA Sheet with Powder Coat finish. Modesty panel : Made from 18mm both side prelaminated particle boards.All edges are covered by 0.8mm PVC edge bands glued by hot melt glue applied by auto edge banding machine.KEYBOARD TRAY(WITHOUTMOUSETRAY):- MetalPowderCoated-BlackColor,CPU TROLLEY:- MetalPowderCoated-BlackColor,3DRAWERPEDESTALUNIT having overall size 392L x 450D x 680Ht. mm. with central lock and key. Drawers and body are complete metal with powder coat finish, facia in 18 mm prelaminated particleboard, 44 Medium Height Steel Storage @ 750Lx450Dx1200HTProvidingand fixing Openable Steel Storage of 750 x 450 x 1200Ht, with 2 adjustable shelves, Complete body & shutter made in0.8 mm thick & Top in 2 mm thick CRCA, 2 Shutter to be mounted with the help of cup hinges, and 4 adjustable levelers, enitre storage in powder coated finish with 60 to 80 microns. with 25 mm. thk. as per drawing. 45 Sofa Set 3+1+1Providing&fixing SofaSet3+1+1BrownandCreamleatherDIMENSIONLength:182.5 (cms)Breadth (cms): 100 (cms)Height (cms): 100 (cms) Weight (Kilograms): 66 (Kilogram) Seating Capacity: Five Seat 46 Stool for Lab and Class-IVProviding and fixing 4 legged Lab stool, Legs made of 16 Guage 45 MM Outer dimension MS Pipe, Duly painted, With a 304 Grade Stainless steel 12 inch wide seat with a 1 inch collar,Heightadjustmentviaascrew.asperdesignanddrawingandinstructionsofEngineer in charge. 47 Providing & Arrangemnt of High Back Chair - TILT MECHANISM WITH MULTILOCKING,HIGHDENSITYCUSHIONONSEATCOMPOSITELEATHER WITH METALLIC SILVER FINISH BASE AND ARMS WITH P.U.CASTORSGASLIFT FOR HEIGHT ADJUSTMENT. 48 Providing and applying priming coat over new wood and wood based surfaces, including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter, sand papering and knotting, scaffolding etc. complete. 49 Providing and fixing mild steel grill work for windows, ventilators etc. 20 Kilogram/ One Square Metre asperdrawing including fixtures,necessarywelding andpainting with one coatsof anticorrosive paint and two coats of oil painting complete. 50 Providing and fixing rolling shutter fabricated from steel laths of minimum thickness 0.9 mm with lock plate of 3.15 mm thickness reinforced with 35 x 35 x 5 mm angle section fittedwith sliding bolts and handles for both sides, deep M.S. channel section of depth and thickness not less than 65 mm and 3.15 mm respectively with hold fast arrangements,M.S.Bracketplate300x300x3.15mmminimumsizeandshapewithsquarebar, suspension shaft of minimum 32 mm diaMetre, hood cover of M.S. sheet not less than 0.9 mmthicknessandofanysizeattopandsafetydevicesincludingmechanicalgear operation arrangement consisting of worm gear wheels and worms of high grade cast iron ormildsteelandonecoatofredleadprimeretc.complete.(I.S.62481979)(With mechanical gear) 51 ProvidingfixingMangaloretileroofingwithclassAAtilesincementmortar1:4onsloping slab including necessary scaffolding, curing, finishing, etc. complete. 52 Providing and fixing valley gutter of 22 B.W.G. (0.8 mm) plain galvanised iron sheets 120 cm widewithteakwoodplanking20mmthickincludingtwocoatsofcoal-tarring theupper surface of plank etc. complete. (excluding painting to underside of plank). 53 Providing andfixinginpositionGypsum boardfalseceilingwith 12.5mm thick Gypsumboards,screwed/fixed to the under structure of suspended G.I. Grid constructedand suspended from the main ceiling consisting of ceiling sections of size 25 x 50 mm maximum centertocenterdistanceof600milimetreperiMetrechanneland intermediate channels atmaximum center to center distance 1200 milimetre galvanizedgridshouldbefixedto reinforced cement concrete slab. The gypsum board shouldbefixedtogalvanizedirongridwithnecessaryscrews. Theboardsshouldbetaped and filled from underside to give smooth, seamless ceiling.The rateshould include necessary additional ceiling sections and intermediate channels.Additional intermediate channels should be fixed to strap hangers for additional support to prevent strapping at every 1200 milimetre item to be completed inall respect including necessary sleeves for ducts finishing of joints cut outs, painting including labour, material, lifts etc. all complete. 54 Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted / bolted /welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete. 55 Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)(Concrete Non Scada) 56 Providing and fixing corrugated galvanised iron sheets of 0.63mm thick (24 B.W.G.)for roofing without wind tiles including fastening with galvanised iron screws andbolts,leadandbitumenwashersasperdrawingetc.complete.(Weightof5.5Kilogram/sq.m.). 57 Providing and laying cement concrete pipe of IS 458:2003 NP-2 class of 450mm diaMetre in proper line, level and slope including providing and fixing collars in cement mortar 1:2and curing etc. complete. 58 Providing and fixing heavy duty inter locking concrete RUBBER MOULD GLOSSY PAVING BLOCKS of 60 milliMetre thickness of having a strength of 400 Kilogram/sq.m of approved quality and shape on a bed of crushed sand of 25 to 30 milliMetre thick including striking joints and cleaning etc. complete. (using 100% crushed sand 59 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting with Vibratory roller. to the required density. By Mechanical Means - Grading I (Using Screening Type A (13.2) mm Aggregate) 60 Providing and laying in situ cement concrete M -30 with tremix treatment for 200 mm thickness for Concrete Road is including laying plastic sheet for 125 micron thickness with groove cutting of 4 mm wide and 20 mm deep with necessary refilling with bitumen ( excluding reinforcement) with coarse and fine aggregate ( natural sand/ VSI grade finely washed crushed sand) etc. complete with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete.(Non SCADA Item) 61 Excavationforfoundationinearth,soilofalltypes,sand,gravelandsoftmurum, including removingtheexcavatedmaterialuptoadistanceof50m.beyondthe buildingareaand stackingandspreadingasdirected,dewatering,preparingthebed forthefoundationand necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means 62 Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete 63 Providing rough cast cement plaster externally in two coats to concrete, brick or stone masonry surfaces in all positions with base coat of 12 to 15 mm thick in C.M. 1:4 and rough cast treatment 12mm thick in proportion 1:1 1/2:3 including scaffolding and fourteen days curing complete 64 Providingandfixingcollapsiblesteelgateinone/twoleaveswithhotrolledvertical channels of 18 x 9 x 3 mm minimum size, crossings of M.S. flats of size 18 x 5 mm T or E section for runner of minimum 40 x 6 mm size for flange, M.S. flat for top runner of minimum size 40 x 12mmwithrollerwheelsconfirmingtogradeF.G.150fitted withsnapheadedrivets of minimum size 6 mm max. spacing of vertical channels be 100mmenclosedgatepositionandclear space of 150 mm between two sets of crossingswithholdfasts,stoppers,spaces, handles, locking arrangement and one coat of red lead primer and oil painting etc. complete. (I.S. 105211983). 65 Providing and erecting chain link fencing 1.6 M. height with G.I. chain link of size 50x 50 mm, 8 gauge thick and fixed 75 mm above ground level on vertical M.S. Angles of 40 x 40 x 6 mm size, includind excavating pits for foundation and embedded in C.C. block of 1:4:8 mix of size 450 x 450 x 670 mm. at 1.75 M. c/c with iron bar 16mm dia as hold fast including welding link with angle frame at 30 cm c/c with nuts and bolts and horizontalM.S. Angles at top andbottom of 25 x 25 x 5 mm size andvertical M.S. flat 35 x 5 mm and25 x 5mm horizontal including cross support of 40 x 40 x 6 mm angles both side at every corner or bend embedded in concrete blocks of 1:4:8of size 450 x 450 x 670 mm including 3 coats of oil painting etc. complete.
