tender for Nrsmc And H Ca Cb Building Orthopedic Dept Urgent And Special Repairing Of Ceiling And Distress Concrete Areas And Allied Necessary Works During The Fy 2025 2026- 1 Taking out Mirzapur or glazed porcelain tiles carefully bychiselling from walls or floor including stacking serviceablematerial as directed. 2 Stripping off worn out plaster and raking out joints of walls, celingsetc.upto any height and in any floor including removing rubbish within a lead of 75m as directed. 3 Uprooting and removing plants from the surface of walls parapet etc and making good damages. (Repairing of damages to be paid separately).(b) Medium size plant of girth of exposed stem above 75 mm. but not exceeding 150 mm. lift upto 6 mtr. 4 Dismantling all types of masonry excepting cement concrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m. 5 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor.(Add. above ground floor - 1st. floor). 6 Cleaning the exposed reinforcement preferably upto full diameter by wirebrush, applying two coats of polymer based rust removing compound left for24 hours, removing the coating and then applying two (2) coats of polymermodified anti corrosive protective coating formulated to inhibit the corrosionof reinforcement as per manufacturers specification] [Mode of measurement:The affected surface area of reinforcement shall beconsidered for payment] 7 Applying 2 coats of Acrylic Polymer modified Paint (Equivalent to MASTER CRETE M-81 OF CHOKSEY OR SIMILER SPECIFIED PRODUCT) having water proofing cum bonding properties ….etc 8 Cement concrete (1:1.5:3) with graded stone chips 5.6 mm size with hexagonal square mesh wire netting, I.R.C. fabric mesh or X.P. M. fitted and fixed after tying the existing reinforcement on concrete without distributing the same and with proper scarping and cleaning the reinforcement and disturbed concrete with wire brush etc. after applying a coat of cement including the cost of wire netting I.R.C or X. P. M. & cost of all handling and scaffolding complete as per direction of Engineer-in -charge.a) 20 mm thick 9 Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints or rougening of concrete surface, including throating, nosing and drip course where necessary (ground floor)(i) With 1:6 cement mortar(b) 20 mm. thick plaster 10 (ii) With 1:4 cement mortar(c) 10 mm thick plaster 11 (i) Hydraulic door closer of approved quality as per I.S.I. standard fitted and fixed complete :.(b) Medium (I.S.I. size 2). 12 Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of keystones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.(B) WallWith Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.(b) Area of each tile above 0.09 Sq.m(i) Coloured decorative 13 Supplying, fitting and fixing fibre reinforced polymer (FRP) Composite doorframe as per approved section with glass fibre reinforced plastic moulded skins and a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science and Technology (DST) to safisfy IS: 4020 door testing performance criteria..(i) 66mm x 90mm 14 Supplying, fitting & fixing fibre reinforced polymer (FRP) Composite doorshutters as per approved design with glass fibre reinforced plastic moulded skinsand a special sandwich core, so as to impart monolitaheic composite structure asper approved technology of Department of Science and Technology (DST) to satisfy IS:4020 door testing performance criteria.In 1st floor.(i) 32 mm thick 15 Supplying,fitting & fixing of 2-Track / 3-Track Aluminium slidingWindow of all Aluminium sections viz. window frame (top,bottom & sideframe), shutter (top, bottom, side & interlock member) made of aluminiumalloy extrusions conforming to IS 733-1983 & IS 1285-1975, annodisedconforming to IS 1868-1983, fitted with all other accessories viz. PVCroller, EPDM gasket, maruti lock, screws etc. including labour chargesfor fitting & fixing of aluminium 2-track/3-track sliding window withfixing of glass (excluding cost of glass) all complete as per architecturaldrawings and direction of Engineer-in-charge.10-12 Micron thickness Annodizing filmNatural white 16 Supplying bubble free float glass of approved make and brand. Conforming to IS: 2835-1987.(iii) 5 mm thick clear glass. 17 Anodised aluminium butt hingesof approved quality manufactured from extruded section conforming to I.S. specification (I.S.205/66) and fitted and fixed with cadmium plated screws:.(v) 100 x 63 x 3.2 mm. 18 Anodise aluminium barred/tower/socket bolt (full covered) of approved manufactured from extruded section conforming to I.S.204/74 fitted and Fixed with cadmium plated screws:.(iv) 150 mm long x 10 mm dia. bolt. 19 Anodise aluminium Aldrop/Slidingbolts of approvedquality manufactured form extruded section conforming to I.S. specifictation (I.S.2681/66) fitted and fixed complete.(i) 250 mm x 16 mm dia. bolt 20 Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S.230/72) fitted and fixed complete:.(a) With continuousplate base (hexagonal/round rod).(vi) 150 mm grip x 10mm dia rod. 21 (b) Rendring the surface of walls and ceilingwith white cement based wall putty of approved make and brand (1.5mm thick). 22 Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturers specification)including cleaning and smoothning of surface.Two Coats 23 Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete (In all floors for internal wall & upto 6m height for external wall ).(ii) 4 mm. thick. 24 Cutting Joints of existing floor and walls (granite/marbel/tiles etc)/ 3mm wide x 7 mm deep and filling the joints with 100 % stain free, chemical and temperature resistant , anti bacterial and anti fungal apoxy grout with approved manufacture to match the colour of existing floor/ wall including the cost of materials, labour and other incidental charges complete true to the manufacturer specification and direction of Engineer-in-Charge. 25 Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint.(ii)550 mm X 400 mm size 26 Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware ofapproved make complete in position with necessary bolts, nuts etc.(a) With P trap 27 Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc 28 Supplying,fitting and fixing 32 mm dia. Flush Pipe of approved make with necessary fixing materials and clamps complete. i) Polythene Flush Pipe 29 (e) PTMT (Polytetra Bib Cock / Stop Cock ( Prayag or equivalent)15 mm 30 Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia.(ii)450 mm long 31 Supplying,fitting and fixing approved brand 32 mm dia.P.V.C. waste pipe, with PVC coupling at one end fitted with necessary clamps.(iii) 900 mm long 32 Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete (b) Anglo Indian(ii) Plastic (hallow type) white 33 (f) Hand Shower(Health Faucet) with 1mtr Fexible Tube with WallHook(Equivalent to Code No.573 & Model -ALLIED of Jaquar orsimilar). 34 Supplying, fitting and fixing soap holder.(a) PTMT (Prayag or equivalent) 35 Supplying, fitting and fixing best quality Indian make mirror 5.5 mm thick with silvering as per I.S.I. specifications supported on fibre glass frame of any colour, frame size 550 mm X 400 mm 36 Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 37 Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately)(a) For Exposed Work20 mm
