Tender For Addn / Altn Cum Special Repair To Certain Dm Accn At Pachmarhi Station.; 2 Item No 01 :Demolition of cement concrete un reinforced in ground floor and paving n exc 15cm thick complete all as specified and directed. 3 Item No 02 : Dismantling floor, walls, roof tiles including bedding but not backing and rubbish off permises complete all as specified and directed. 4 Item No 03 :Demolition of reinforcement cement concrete above ground floors n exc 15 cm thickness (Reinforcement cut as required to facilitate demolition) such as cooking platform, chajjas etc complete all as specified and directed. 5 Item No 04 :M&L for Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand ) to match the existing floors complete all as specified and directed. 6 Item No 05 : M&L for Treatment of soil along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron, complete all as specified and directed. 7 Item No 06 : M&L for 10 mm thick Light shade double charge vitrified tiles in floors, exc 0.36 sqm but n exc 0.42 sqm set & jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed. 8 Item No 07 : M&L for 10 mm thick Dark shade vitrified tiles in floors, exceeding 0.36 sqm but not exceeding 0.42 sqm set & jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed. 9 Item No 08 : M&L for 10 mm thick light shade double charge vitrified tile in vertical surface, exc 0.36 sqm but n. exc 0.42 sqm set & jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed. 10 Item No 09 : M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick, area of each tile exc 0.18 sqm & n. exc 0.38 sqm in floors etc set & jointed in neat cement slurry and pointed with white or coloured cement to match complete. 11 Item No 10 : M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exc 0.11 sqm & n exc 0.18 sqm in floors etc set & jointed in neat cement slurry and pointed with white or coloured cement to match complete. 12 Item No 11 : M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick,area of each tile exc 0.18 sqm, & n exc 0.38 sqm in vertical surface such as skirtings, dados etc, set and jointed in neat cement slurry and pointed in white or coloured cement complete. 13 Item No 12 : M&L for screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:6 for laying of floor tiles complete all as specified and directed. 14 Item No 13 : M&L for 25 mm thick cement concrete (1:2:4), type B-0, using 12.50 mmgraded aggregate as in floors complete all as specified and directed. 15 Item No 14 : M&L Machine cut Kota stone slab flooring 20-25mm thick as in floor, over cement mortar laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab of the slab incl rubbing, polishingcomplete incl 20mm thick screed in CM 1:6 complete all as specified and directed. 16 Item No 15 : M&L for kota stone slab 20-25mm thick machinecut bull nosed in riser of steps ,skirting, dado and pillar laid over cement screed backing in CM 1:4, 10mm thick and match with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete 17 Item No 16 : M&Lfor glazed ceramic coloured tiles 450 x 300 x 7 mm thick on vertical surface such as dado / skirting / risers to steps etc jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles complete all as specified and direct.nd directed. 18 Item No 17 : M&L for rendering 10 mm thick in CM 1:4 on fair faces of brick or concrete surface of wall finished even & rough complete all as specified and directed. 19 Item No 18 : Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed. 20 Item No 19 : M&L Brick work with sub class B bricks straightor curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed. 21 Item No 20 : M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation, sub base, mass concrete complete all as specified and directed. 22 Item No 21 : M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation, sub base, mass concrete complete all as specified and directed. 23 Item No 22 : M&L for PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in holdfast, cills, copings, bed plate, plinth courses, roof kerbs or mud stops rounded or chamfered on edges including necessary form workcomplete all as specified and directed. 24 Item No 23 : M&Lfor reparing of RCC projection, chajjas, roofs, facia, colum etc. by neccesary preparation i.e scrapping, cutting, chiseling, derusting and clearing exposed reinforcement, surfaces of damaged, loose RCC surfacess and applying one coat of rust remover by brushing to rusted reinforcement to remove loose rust particles and allow to dry it for 2 to 3 hrs, insert the new reinforcement to damaged portion by drilling hoe at required distance, fill the epoxy into the hole by 2/3 of the hole and insert the reinforcement in the hole and binding the reinforcement at rusted portion of reinforcement, applying cement, slurry entire damaged area and plaster the surface with cement and sand and polymer liquid in 1:3:15 % of cement by weight and water as required, mixing properly and plaster the surface finished even and smooth by making the edge water dropping groves complete all as specified and directed. Note: cost of ormwork shall be also deemed to be included, in the quoted rate. 25 Item No 24 : Taking down cement plaster any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed. 26 Item No 25 : M&L for rendering on fair faces of brick workor concrete surfaceof wall 15mm thick in CM 1:6 and to be finished even and smooth with out using extra cement complete all as specified and directed 27 Item No 26 : M&L for rendering 15 mm thick in CM (1:4) in two layers (1st layer 10 mm thick rendering coat and 2nd layer 5 mm thick finishing coat) on brick work or concrete surfaces, second layer (finishing coat) mixed with liquid water proofing compoud @200ml /50 Kg bag of cement as per manufacturers instructions and finished the surfaces even and fair wothout using extra cement complete. Note: Liquid WPC will be measured and paid separately. 28 Item No 27 : M&L for rendering 10 mm thick in CM 1:3 on concrete surfaces of ceiling finished the surfaces even and smooth complete all as specified and directed . 29 Item No 28 : Supply only liquid water proofing compound, ISI marked. 30 Item No 29 : Taking down chowkats or frames not exc 1.5 Sqm each with shutters ( with out taking off shutters from the frames) incl making good the disturbed portion complete all as specified and directed. 31 Item No 30 : Taking down chowkats or frames exc 1.5 sqm but not exc 4.0 Sqm each with shutters ( with out taking off shutters from the frames) incl making good the disturbedportion complete all as specified and directed. 32 Item No 31 : Taking down shutter of any description exc 1 sqm and not exc 2 sqm each complete all as specified and dir. 33 Item No 32 : Taking down shutter of any description n. exc 1 sqm each complete all as specified and dir. 34 Item No 33 :Cutting holes in brick walls exc half brick but not exc one brick built in cement mortor or cement lime mortor and stone walls built in lime mortor for inserting hold fasts and makinggood dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as requiredcomplete all as specified. 35 Item No 34 : S&F 35 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (with sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc fitted to chowkhats for doors etc complete all as specified. 36 Item No 35 : S&F Anodised aluminium frame with power coating (minimum thickness of powder coating 50 micron)for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified. 37 Item No 36 : S&F Factory made 35 mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces and size of the members of shutter are per IS : 1003 (Part I), kiln seasoned and chemically pressure treated 2nd class hardwood rail and style complete all as specified. 38 Item No 37 : S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. 39 Item No 38 : S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings,frame work of watertanks and similar work conforming toFe -290 Gde E-165 complete all as specified and directed. 40 Item No 39 : S&F pressed steel frames of size 105 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including one shop coat of priming complete all as specified and directed.. 41 Item No 40 : S&F pressed steel frames of size 165 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including one shop coat of priming complete all as specified and directed. 42 Item No 41 : S & F for solid PVC door frame of size 50x47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplied and fixing in opening as specified and shown on drawing complete all as specified. 43 Item No 42 : S & F for 30mm thick Factory made single extruded WPC (Wood Polymer Composite) solid Moulded WPC door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately) 44 Item No 43 : S & F factory made solid panel PVC door shutter 30 mm thick style consisting of frame made out of MS tube for top and bottom rails.MS frame shall be covered with heat moulded plain colour PVC “C” channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, S & F in the frame as shown on drawing in section 8 of SSR-2020 Part-II complete all as specified and directed. 45 Item No 44 : M&L SS Butt hinges, medium weight with galvanised mild steel hinge pin anodised for 100 mm long complete all as specified and directed. 46 Item No 45 : M&L SS Butt hinges, medium weight with galvanised mild steel hinge pin for 75 mm long complete all as specified and directed. 47 Item No 46 : S&F Butt hinges, medium weight, cold rolled mild steel 100 mm long complete all as specified and directed. 48 Item No 47 : S&F SS grade 304 sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet and fixing bolts and sliding bolts of stainless steel grade 304 of 300 mm length of bolt complete all as specified. 49 Item No 48 : S&F mild steel, 150 mm long ordinary helical door spring incl roller and roller plate complete all as specified and directed. 50 Item No 49 : S&F SS Grade 304, barrel tower bolts of section 200 mm long complete all as specified and directed. 51 Item No 50 :S&F SS grade 304, barrel tower bolts of extruded section 150 mm long complete all as specified and directed.. 52 Item No 51 : S&F stainless steel grade 304 handles fabricated type of 150 mm size complete all as specified and directed. 53 Item No 52 : S&F stainless steel grade 304 handles fabricated type of 100 mm size complete all as specified and directed. 54 Item No 53 : S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor, over all length of cover plate 140 mm complete all as specified and directed. 55 Item No 54 : S&F small fittings of PVC door, window stop, window stops and the like not exc 200 cucm each indluding MS butt hinges, medium weight, cold rolled 50 mm long complete all as specified and directed. 56 Item No 55 : S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed. 57 Item No 56 : S&F galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed. 58 Item No 57 : Hacking out old broken glass (any thickness, size, quality or description) from wooden frames / steel frame glazed with oil putty of fixed with beads complete all as specified and directed. 59 Item No 58 : S&F 3 mm thicksheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane, complete all as specified and directed. 60 Item No 59 : S&F figured glass 3 mm thick, pin head type and glazing with oil putty in squares not exc 0.5 sqm in each pane complete all as specified and directed 61 Item No 60 : Taking down old wooden/wood based particle board & S&F 18/19 mm thick high density PVC solid board duly laminated 2mm thick prelaminated PVC sheet on front face (ISI mark) etc in kitchen cupboard / or in any position with SS ball telescope hinges used complete all as specified and directed. 62 Item No 61 : M&L for stainless steel basket size (15 inch X 20 inch X 4 inch) for modular kitchen cutlery tray/basket with complete sliding Arrangement fixed kitchen cabinet framcomplete all as specified and directed. (01 Nos) 63 Item No 62 : M&L for stainless steel basket size (15 inch X 20 inch X 6 inch) for modular kitchen tray/basket with complete sliding Arrangement fixed Kitchen cabinetframcomplete all as specified and directed. (01 Nos) 64 Item No 63 : M&L forstainless steel basket size (15 inch X 20 inch X 8 inch) for modular kitchen crockery tray / basket with complete sliding Arrangement fixed kitchen cabinet framcomplete all as specified and directed. (01Nos) 65 Item No 64 : M&L for stainless steel basket size (15 inch X 20 inch X 10 inch) for modular kitchen grain troIIy basket with complete sliding arrangement fixed kitchen cabinetframcomplete all as specified and directed. (01 Nos) 66 Item No 65 : M&L for stainless steel basket size (15 inch X 20 inch X 4 inch) for modular kitchen tray / basket with complete sliding arrangement fixed kitchen cabinetframcomplete all as specified and directed. (01 Nos) 67 Item No 66 : S & F for Stainless steel wide 110 degree Hydraullic hing fixed with ss screw complete all as specified. 68 Item No 67 : S&F 100 mm hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed. 69 Item No 68 : S&F 100 mm dia extruded SS, fabricated type polished fixed to board complete all as specified and directed. 70 Item No 69 : S&F continuous (Piano) hinges,mild steel, bright finish or electro galvanisedwidth of flaps (when open) 30 mm complete all as specified and directed. 71 Item No 70 : S&F MS mm peg set of six powder coated solid body complete all as specified and directed 72 Item No 71 : S&F in repair stainless steel grade 304 curtain rod 25 mm dia with stainless steel fancy finials & brackets of any colour as approved by GE complete all as specified and directed. 73 Item No 72 : Taking up or down steel tubing and connections including cleaning if refixingrequired for 15 mm bore of pipe complete all as specified and directed. 74 Item No 73 : Taking up or down steel tubing and connections including cleaning if refixingor removal to store of 20 mm dia of pipe complete all as specified and directed. 75 Item No 74 : Supply & laying of CPVC pipes 20 mm outer dia, SDR 11 & plain CPVC SDR 11 fitting on wall / ceiling or laying in floors complete all as specified. 76 Item No 75 : Supply & laying of CPVC pipes 25 mm outer dia, SDR 11 & plain CPVC SDR 11 fitting on wall / ceiling or laying in floors complete all as specified. 77 Note: for Item No 74 & 75(i) CPVC brass threading will be measured and paid separately.(ii) Cost of plain CPVC fttings like Bend, Tee, Elbow, Union etc shall inclusive under the quoted rate of pipe including. 78 Item No 76 : S&F of CPVC 20 mm Outer dia male Brass threaded Adoptor (3/4 x 1/2) (MTA/MBTA) complete all as specified and directed. 79 Item No 77 : S&F of CPVC 25 mm Outer dia male Brass threaded Adoptor (3/4 x 1/2) (MTA/MBTA) complete all as specified and directed. 80 Item No 78 : S&F of CPVC 20 mm Outer dia female Brass threaded Adoptor (3/4 x 1/2) (MTA/MBTA) complete all as specified and directed. 81 Item No 79 : S&F of CPVC 25 mm Outer dia female Brass threaded Adoptor (3/4 x 1/2) (MTA/MBTA) complete all as specified and directed. 82 Item No 80 : S&F of CPVC 25 mm Outer dia brass Tank Adoptor complete. 83 Item No 81 : S&F of CPVC 25 mm Outer dia brass Union complete. 84 Item No 82 : M&L cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good in brick walls, cutting not exceeding 10 cm girthcomplete all as specified and directed. 85 Item No 83 : S&F in repair chromium plated single lever basin mixer single lever withouy popup waste system with 450 mm long braided hoses complete. 86 Item No 84 : S&F in repair chromium plated single lever wall mixer 3-in-1 system with provision of both hand shower cimplete with 115mm long bend pipe, connecting legs and flange complete. 87 Item No 85 : S&F in repair vitrecous china WHB size 630x450 mm white flat back including PVC waste pipe but excludingtaps, waste, chain & plug & porcelain stopper but including brackets with two coats of synthetic enamel painting over a coat of red oxide primer etc complete. 88 Item No 86 : S&F in repairs white vitreous china wash down water closet pan pedestal pattern (white) including fixing bolts & excluding flushing cistern and flush pipe complete all as specified and as directed. 89 Item No 87 : S&F in repair 10 Ltr capacity PVC valveless shyphonic action type low level flushing cistern white with inlet, ball valve, float valve and handle incl bracket and flush pipe of low level of 32mm dia fixed to wall complete. 90 Item No 88 : S&F in repair chromium plated health foucet with 8mm dia and 1.2 m long flexible tubes and wall hook suitable for EWC including nut/washer complete. 91 Item No 89 : S&F in repair PVC connection 15mm dia size and 450 mm long with 2 Nos check nuts its washers complete all as specified and as directed. 92 Item No 90 : S&F cabinet mirror, box type of size 19 x 21 of colour as approved fixed to wall compete. 93 Item No 91 : S&F in repair 5mm thick looking mirror 600 x 450 mm selected quality glass mounted on 6 mm thick commercial plywood, with aluminium beading and fixed to wall with brass screws, cups and washers complete as specified and directed. 94 Item No 92 : S&F in repair bib tap 15 mm bore, long body chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete. 95 Item No 93 : S&F for repair 15mm bore pillar taps cast copper alloy, with capstan head chromium platedscrewed down high pressure with or without lettered Hot or cold with long screwed shanks and fly-nuts screwed for iron pipe & fixed complete. 96 Item No 94 : S&F for repair CP brass tubular towel rail 20 mm dia D type 60 cm long between flanges complete. 97 Item No 95 : S&F for repair aluminium anodised tubular towel rail, 20 mm dia, D type, 60 cm long between flanges complete all as specified and directed. 98 Item No 96 : S&F in repair angle cock 15 mm bore fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe. 99 Item No 97 : S&F in repair CP two way angle valve with wall flanges 15 mm bore, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed 100 Item No 98 : S&F in repair of stainless steel soap dish, of standard size and shape complete. 101 Item No 99 : S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen with plugs, washers and wastes, & waste pipe incl bedding in cement mortar to dwarf wall or incl fixing suitable sizes of cantilever brackets and connecting union to pipe overall size 915 x 460 mm,bowl size 410 x 330 x 160 mm complete. 102 Item No 100 : S&F repair 0.63 mm thick kitchen plate rack made of stainless steel 900 x 750 x 220 mm size fixing with wooden plug with suitable size of screws complete all as specified. 103 Item No 101 : S&F in repair chromium plated overhead shower rose swivel type 125 mm with CP arms 300 mm long complete all as specified and directed 104 Item No 102 : S&F 15 mm concealed type stop valves, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed but fancy type, chromium plated with long shank and cup. 105 Item No 103 : S&F in repair plastic water closet seat cover, Cream / white colour, closed pattern with flat bottom and cover and mild steel chromium plated aluminium hinging device for pedestral pattern WC. 106 Item No 104 : S&F PVC (SWR) P trap for 110 mm dia etc complete. 107 Item No 105 : S&F in repair chromium plated toilet paper holder with flap complete. 108 Item No 106 : M&L for RCC (nominal mix) 1:2:4 type B-1 using 20 mm graded stone aggregate as in kitchen platform, shelves & chhajja and similar workincl form workcomplete all as specified and directed.Note - Reinforcement shall be measured and paid separately. 109 Item No 107 : M&L for 18 mm thick granite(of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including 15 mm thick screed bed in cement mortar edge moulding & cutting hole for gas pipe and similar work and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. 110 Item No 108 : M&L for machine cut cudappah stone slab 20 to 25 mm thick over cement screed base including 15 mm thick screed bed in cement mortar (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. 111 Item No 109 : Mild SteelTMT bar 8 mm dia cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 112 Item No 110 : Taking down AC/PVC pipes (including all fittings), with spigot and socket ends lead joints including burning out joints of 100 mm dia pipe complete all as specified and directed. 113 Item No 111 : M&L for PVC (SWR) pipes 110 mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors etc complete all as specified and directed. 114 Item No 112 : M&L for PVC (SWR) pipes 110 mm bore single socketed, in any length with rubber ring joints, fixed to wall etc complete all as specified and directed. 115 Item No 113 : S&F for PVC (SWR) pipessingle socketed, in any length with rubber ring joints, laid in trenches or in floors of 75 mm bore of pipe etc complete all as specified and directed. 116 Item No 114 : S&F stack clamps made out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays, including bolts and nut and securing ends of stays to wall or roof for 110 mm bore of pipe complete all as specified and directed. 117 Item No 115 : S&F PVC (SWR) bends any radius of 110 mm borewith outaccess door complete all as specified and directed. 118 Item No 116 : S&F PVC (SWR) bends any radius of 110 mm borewithaccess door complete all as specified and directed. 119 Item No 117 : S&F of PVC(SWR) Tee of 110mm dia etc complete all as specified and directed 120 Item No 118 : S&F PVC (SWR) bends any radius of provided withaccess door of 75 mm dia complete all as specified and directed. 121 Item No 119 : S&F PVC (SWR) branch pieces, single (equal or un equal), ordinary or inverted (spigot or socket type) or with parralled branches of 110 mm dia with access door. 122 Item No 120 : S&F PVC (SWR) branch pieces, single (equal or un equal), ordinary or inverted (spigot or socket type) or with parralled branches of 75 mm dia with access door. 123 Item No 121 : S&F PVC (SWR) vent cowl 110 mm bore 124 Item No 122 : S&F PVC (SWR) multi floor trap, plain with grating with or without waste hole including jointing with solvent cement 75 mm dia etc complete. 125 Item No 123 : Dismantling water tanks and removing to store of capacity exc 250 and n exc 500 ltrs all as specified. 126 Item No 124 : Dismantling water tanks and removing to store of capacity exc 500 and n exc 1000 ltrs all as specified. 127 Item No 125 : S&F Rotational moulded polyethylene water storage tanks in white colour tripple layer (cylindrical vertical with closed top) hoisted and and fixed in position all as specified in SSR Pt-I of 500 Ltr capacity all as specified. 128 Item No 126 : S&F Rotational moulded polyethylene water storage tanks in white colour tripple layer (cylindrical vertical with closed top) hoisted and and fixed in position all as specified in SSR Pt-I of 1000 Ltr capacity all as specified. 129 Item No 127 : S&F Ball valves 25 mm dia high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. 130 Item No 128 : S&F in repairs Gun metal, globe or gate valve with iron wheel head, 25 mm bore, screwed both ends for iron pipe complete. 131 Item No 129 : M&L for preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over a coat of primer complete. 132 Item No 130 : M&L for preparation of new steel surfaces any description, any described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red-oxide primer complete. 133 Item No 131 : Removing old paints by paint removes or burning off by blow lamps and cleaning with scrapers, any number of coats, any width or girth complete. 134 Item No 132 : M&L Preparing old wooden surfaces exceeding 10Cm in width or girth and applying two coats of synthetic enamel paint over a coat of primer complete. 135 Item No 133 : M&L Preparing old steel surfaces exceeding 10Cm in width or girth and applying two coats of synthetic enamel paint over a coat of primer complete. 136 Item No 134 : M&L for applying 2mm thick wall care Putty in two layers on old wall surfaces including complete removal of existing wall finish of any type with wire brush, brooming, dusting and finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc. and rubbing with sand paper and making the surface even & smooth complete all as specified and directed. 137 Item No 135 : M&L for preparation of newly plastered surfaces of wall & concrete and applying 2 mm thick wall care putty including preparation complete all as specified and directed. 138 Item No 136 : M&L for applying two coats of oil bound distemper on wall or concrete over a coat of primer on prepared surfaces including rubbing with sand paper complete all as specified and directed. 139 Item No 137 : M&L for applying two coats of oil bound distemper on ceiling over a coat of primer on prepared surfaces including, rubbing with sand paper complete all as specified and directed. 140 Item No 138 : M&L for preparation of old decorated surfaces of walls by washing, rubbing down and scrapping of distemper surfaces and applying one coat of oil bound distemper of any light shade complete all as specified and directed. 141 Item No 139 : M&L for preparation of old decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coat of white wash complete. 142 Item No 140 : M&L for preparation of old surfaces of ceilings and apply two coat of white wash complete all as specified and directed. 143 Item No 141: M&L Preparation of new plastered or unplastered surfaces of wall and applying two coats of cement based paint over a coat of primercomplete all as specified as directed. 144 Item No 142 : M&L Preparing old painted surfaces of walls, chajjas etc by washing rubbing down and stopping and applying two coat of cement base paint white or tinted complete all as specified as directed. 145 Item No 143 : Preparing surface of sunken slab and applying 15 mm thick cement plaster 1:4 cement sand mortar with integral water proofing compound both on floor and wall. The surface shall then be cured and allowed to dry then applying Epoxy Resin coating polymer modified cementitious coating like brush bond of Fosroc, Pidilite and Bostic as per manufacturers instructions both on floor as well as on wall and sunken floor shall be filled with graded cinder complete all as specified. (IWPC will be paid separately) 146 Item No 144 : M&L for complete removal of existing water proofing treatment from top of roof and canopies/chajjas of building including removal of debris out side MD land. Water proofing treatment in following sequence through manufacturer / authorized applicator of the manufacturer including taking down of existing roof treatment, properly cleaning & drying the concrete surfaces complete(a) 10 mm thick rendering on roof surface/concrete surface in CM 1:4 complete.(b) Applying a coat of oxidised bitumen based solvent primer @ 0.3 Kg/Sqm(c) Applying preventely a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm mtr incl cleaning surfaces. (d) Laying unrolled over the bitumen coated surface, polymeric water proofing membrane Hyperplas standard wt not less then 3kg/Sqm with 100 mm over laps shall be sealed by flame as per manufacturers instructions.(e) Applying two coats of bituminous aluminium paint including preparation complete 147 Item No 145 : M&L for complete removal of existing water proofing treatment from top of roof and canopies/chajjas of building including removal of debris out side MD land. Water proofing treatment in following sequence through manufacturer / authorized applicator of the manufacturer including taking down of existing roof treatment, properly cleaning & drying the concrete surfaces complete(a) 10 mm thick rendering on roof surface/concrete surface in CM 1:4 complete.(b) Applying a coat of oxidised bitumen based solvent primer @ 0.3 Kg/Sqm(c) Applying a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm mtr incl cleaning surfaces. (d) Laying over the bitumen coated surface, polymeric water proofing membrane Hyperplas standard wt not less then 3kg/Sqm with 100 mm over laps shall be sealed by flame as per manufacturers instructions. 148 Item No 146 : M & L Hydrulically pressed burnt clay tile plain of size 200x200x19/20 mm machine made laid over roof & including cement mortar screed 15 mm thick in CM 1:6 mixed with water proofing compound and jointed in CM 1:3 mixed with 5% crude oil by weight of cement. 149 Item No 147 : Dismantling timber scantlings 40 sqcm and over in section as in framed work in any position complete all as specified and directed. 150 Item No 148 : S & F MS framed works as in purline, raftrs, column square/rectangular, round or angle section. Fixed with and including iron cleats or other connected plates flate iron wind riles etc incl bending of MS section as requriedcomplete all as specified and directed. 151 Item No 149 : Excavation in post holes each n. exc 0.5cum getting out in soft / loose soil, ramming earth filling or broken rubble mixed with earth around in layers n. exc 25 cm watering and removing surfaces soil to a distance n. exc 50m and making good surface complete all as specified and directed.. 152 Item No 150 : S&F Wire netting of galvansied steel wire 1.40 mm dia size of mesh in 25 mm fixed with tinned tacks of wire tacks of wire staples as in repair complete all as specified and directed. 153 Item No 151 : Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as speified and directed 154 Item No 152 : Pre-painted galvalume zinc coating GI based corrugated,steel sheet 0.50mm thick of an colour having tensile strength of 550 MPA as in roof covering /cladding to wall, including ridge of same colour fixed with self tapping screws as specified. 155 Item No 153 : M & L pre-cast RCC cover slab 1:2:4 type B-1 (using 20 mm graded stone aggregate) incl all form work and set in cement mortar 1:4 complete all as specified and directed 156 Item No 154 : M&L Cement concrete 1:2:4 type B-2 using 40mm graded aggregate as in surface channels and drains incl necessary form work complete all as specified and directed. 157 Item No 155 : Extra for forming fair finished drain or channel, 30 cm inner girth in cement concrete using extra cement incl forms , moulds ,mitred stopped ends etccomplete all as specified and directed 158 Item No 156 : M&L Concrete bed to drain pipes 150mm, including packing under, and haunching against the sides of pipes after they are laid and tested; in PCC(1:4:8) Type D-2. complete all as specified and directed. 159 Item No 157 : M&L Slat-glazed stoneware drain pipes 150 mm dia laid in trenches and jointed complete all as specified and directed. 160 Item No 158 : M&L PCC(1:3:6) type C1 as in benching to man hole complete all as specified and directed. 161 Item No 159 : M&L for shotcrete/Gunite sprayof 1:3 CM wet mix with admixture using welded wire fabric onto prepared surface of wall/Ceiling having minimum compressive strength of 24.5 Mpa after 28 days complete all as specified and directed. 162 Item No 160 : Dismantling of ceiling board with fittings and any decription including cover fillets and dir. 163 Item No 161 : M&L for suspended false ceilling comprising of 6mm thick non asbestos fibre cement bulding boards fixed or laid/inserted to GI frame work with screws over Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified 164 External Electrical Supply 165 Item No 162 : Taking down existing old Extg unserviceable LT UG/ service cable of any description and size complete all asspecified and directed. 166 Item No 163 : Supplyand laying & testing and commisioning LT underground cable 1100 volts grade, XLPE insulated and PVC sheathed heavy duty armoured with multi staranded aluminium conductor laid in pipes, trenches/ducts, on poles etc for service connections of following size complete all as specified and directed. 167 (a) 3.5 Core x 35 Sqmm 168 (b) 4 Core x 16 Sqmm 169 Item No 164 : Excavation in trenches not exc 1.5 mtr wide & not exc 1.5 mtr in depth for foundation etc or for shafts, wells, cesspits, manholes, laying of pipe and exc 10 foundation etc or for shafts, wells, casspits, manholes, laying of pipe and exc 10 sqm on plan and n exc 1.5 m in depth getting out in soft / loose soil complete all as specified and directed 170 Item No 165 : Returning filling in, including spreading, levelling watering & well ramming in layers not exc 25 cm thick complete all as specified and directed. 171 Item No 166 : Removing excavated material to a distance not exc 50 mtr & depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified & directed. 172 Item No 167 : Material and labour for narmada river sand, unwashed and screened dry for cushioning to under ground cable in trenches below and around under ground cable including spreading and levelling complete all as specified and directed. 173 Item No 168 : Supply and laying unreinforced precast concrete cable cover, class LV, type 1 with flat, size 250 mm x 150 mm x 40mmcomplete all as specified and directed. 174 Item No 169 : Material and labour for Earthing complete with galvanised steel earth plate electrode 600mmX 600mmX 6mm thick buried directely in ground vertically ( earth pit not less than 2.25 meters deep below ground level) with top edge of plate not less than 1.5 metres belownormal ground level, connected to galvanised iron wire 4 mm dia by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 15 mm dia. medium grade protection pipe for earth lead complete with charcoal and common salt including watering arrangement with galvanized iron pipe light grade 20 mmdia, PCC chamber, CI grame and cover, MS funnel with wire mesh earthwork in any type of soilstrata and testing on completion. Note: GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.5mtr from earth plate is deemed to be included in rate quoted. 175 External Water Supply 176 Item No 170 : Taking up or taking down steel tubing and connections including cleaning for reflxing or removal to store size 25 mm dia complete all as specified and directed:- 177 (a) 32 mm outer dia pipe 178 (b) 20 mm outer dia pipe 179 Item No 171 : Supplying and laying of CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specifiedfor the following dia of size. 180 (a) 20 mm outer dia pipe 181 (b) 15 mm outer dia pipe 182 Item No 172 : Gun - metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specifiedfor the following dia of size. 183 (a) 20 mm outer dia pipe 184 (b) 15 mm outer dia pipe 185 Item No 173 : Supply and fixing rstoop valves, cast copper alloy, screwed both ends for iron pipe or for unions and flxeck of size 15 mm dia required for gevsers complete all as specified and directed. 186 INTERNAL ELECTRIFICATION 187 Item No 174 : Taking down copper /aluminium point wiring (light, fan, bell,socketor power) complete including fixture and fittings such as switches , ceiling roses , pendent , regulators, sockets, light fitting etc.Removing materials to store for keeping in safe custody or for taking credit (credit a for above items should be made as per condition seperately) and making good distrubed surfaces ofwalls, floors etc complete all as specified and directed at site 188 Item No 175 : Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/ Main Switch including old unserviceable MCCBs/ MCBs, Isolators, etc and making good to disturbed surface complete all as specified and directed 189 Item No 176 : Taking down carefully copper/aluminium Sub main wiring of any size fromsurface/concealed /existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed. 190 Item No 177 : Taking down existing geyser of any capacity after disconnecting all necessary electrical and water supply connections and deposit to MES store yard of AGE (I) Pachmarhi complete all as specified and as directed. 191 Item No 178 : Taking downexhaust fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to exhaust fanand deposit to MES store yard of AGE (I) Pachmarhi complete all as specified and as directed. 192 Item No 179 : Taking down ceiling fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan bladesand deposit to MES store yard of AGE (I) Pachmarhicomplete all as specified and as directed. 193 Item No 180 : Taking down existing single phase electric energy meter of any capacity after disconnecting all necessary electrical connections and deposit to MES store yard of AGE (I) Pachmarhicomplete all as specified and as directed 194 Item No 181 : M & L for Point wiring using approved colour coding as per IS, with multistranded copper conductor1.5 Sq. mm (nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 volts gradeISI-694 marked drawn through in and including heavy duty, PVC concealed conduit of white/ ivory colour including all accessories after chasing in wall/ceiling etc, heavy duty ISI marked including sunk in anodized pressed steel box 1.60 mm thick, 60 mm deep for housing switch socket etc withwhite laminated 3 mm thick hylam sheet cover ISI marked of suitable size complete including PVC insulated multi strandedcopper conductor 1.5Sq mm FRLSH cable as earth wire to common earth dolly for connection to ceiling rose to earth terminalincludingcutting, chasses and makinggooddisturbed surface to match with existing finish with plaster complete all as specified and directed by Engr-in-charge for following :- 195 (a) One light point controlled by one, one way switch 5 Amps 196 (b) One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator 197 (c) One light point controlled by one, two way switch 5 Amps 198 (d) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board. 199 (e) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board 200 (f) One bell point controlled by one, bell switch 5 Amps 201 Item No 182 : Description all as per item No 181 here in before butusing 2.5 sq mm single core copper conductor cable of multistranded flame retardant PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of2.5 sq mm copper conductor flame retardant PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly. 202 Item No 183 : M & L for Point wiring using approved colour coding as per IS, with multistranded copper conductor1.5 Sq. mm (nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 volts gradeISI-694 marked drawn through in and including heavy duty, PVC concealed conduit of white/ ivory colour including all accessories after chasing in wall/ceiling etc, heavy duty ISI marked, with GI sunken boxes 1.2 mm thick, 60 mm deep with earth dolly duly, covered with modular white cover plate with inner frame suitable for modular switches,including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly includingcutting, chasses and makinggooddisturbed surface to match with existing finish with plaster complete all as specified and directed for the following 203 (a) One light point controlled by one, one way switch 5 Amps 204 (b) One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator 205 (c) One light point controlled by one, two way switch 5 Amps 206 (d) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board. 207 (e)One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad 208 (f) One bell point controlled by one, bell switch 5 Amps 209 Item No 184 : Description all as per item No 183 here in before butusing 2.5 sq mm single core copper conductor FRLSH cable of multistranded PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of2.5 sq mm copper conductor FRLSH cable of multistranded PVC insulated unsheathedas earth continuity conductor along with wiring and connecting to the common eath dolly 210 Item No 185 : Description all as per item No 183 here in before butusing 4.0 sq mm single core copper conductor FRLSH cable of multistranded PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of4.0 sq mm copper conductor FRLSH cable of multistranded PVC insulated unsheathedas earth continuity conductor along with wiring and connecting to the common eath dolly. 211 Item No 186 : S & F for switch Piano type single pole 5 amp, 230 Volts complete all as specified and directed 212 Item No 187 : S & F for switch Piano type single pole 15 amp, 230 Volts complete all as specified and directed. 213 Item No 188 : S & Ffor switch Piano type 2 way switch 5 amp, 230 Volts complete all as specified and directed. 214 Item No 189 : S & Ffor switch bell push pianotype 5 amp, 230 Volts Complete all as specified and directed 215 Item No 190 : S & Ffor socket outlet 2-in-1, 5 pin, 5 amp, 230 Volts complete all as specified and directed. 216 Item No 191 : S & Ffor socket outlet 2-in-1, 5 pin, 5/15 amp, 230 Volts complete all as specified and directed 217 Item No 192 : S & Ffor ceiling rose, surface Bakelite with 3 terminals, ISImarked for batten fitting complete 218 Item No 193 : S & Ffor stepped type electronic fan regulator flushType complete all as specified and directed. 219 Item No 194 : S & Ffor modular switch piano flushtype, single pole, one way, and 5/6 Amp single module complete all as specified. 220 Item No 195 : S & Ffor modular switch piano flush type, single pole, one way, and 15/16 Amp single module complete all as specified. 221 Item No 196 : S & Ffor modular switch piano flush type, single pole, two way, and 5/6 Amp single module complete all as specified. 222 Item No 197 : S & F for modular socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module piano flush type complete all as specified. 223 Item No 198 : S & Ffor modular socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module piano flush type complete all as specified. 224 Item No 199 : S & Ffor modular step type fan regulator 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and as directed. 225 Item No 200 : S & Ffor Bell push modular 6 Amps single module complete all as specified. 226 Item No 201 : S & Ffor lamp holder, PVC / Polycarbonate type with back plate suitabl for batten/ slanting fittings complete all as specified and directed. 227 Item No 202 : S & Ffor Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C supply complete all as specified and as directed 228 Item No 203 : S & Ffor modular type TV Socket out let complete all as specified and as directed 229 Item No 204 :M & L forSub main wiring with approved colour coding as per IS with four single core PVC insulated FRLSH cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable sizeincluding concealed in wall etctwo runs of PVC insulated with 6 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed.Note:- Four runs of 6 sqmm cable, two runs of 6 sqmm cable and one run of PVC conduit will be measured as one unit 230 Item No 205 :M & L forSub main wiring with approved colour coding as per IS with two single core PVC insulated FRLSH cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable sizeincluding concealed in wall etcone run of PVC insulated with 6.0 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Two runs of 6 sqmm cable,one run of 6 sqmm cable and one run of PVC conduit will be measured as one unit 231 Item No 206 :S & F for sheet metal enclosure MCBDBTPN4 way Vertical type with 200 Amps rated bus bar 415 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed. 232 Item No 207 : S & F for sheet metal enclosure MCBDBSPN8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed. 233 Item No 208 : S & FforMCB tripple pole and neutral rated capacity 63 Amps, 415 Volts breaking capacity 10 KA, C curve complete all as specified and as directed. 234 Item No 209 : S & F for MCB Single pole and neutral rated capacity 32 Amps, 240 Volts breaking capacity 10 KA, C curve complete all as specified and as directed. 235 Item No 210 : S & Ffor MCB Single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, C curve complete all as specified and as directed 236 Item No 211 : S & Ffor metal clad box suitable for 230 volt 50 Hz AC supply three pin with MCB SP 20/32 Ampsincluding removal of old unserviceable one complete all as specified and as directed complete all as specified and as directed 237 Item No 212 : S & F for water heater storage type (Geyser) vertical/ Horizental type as per site requirement with inner container of capacity 25 ltrs, electrically operated, AC 230 Volts,BEE 5 star rated, ISI markedincluding 04 Nos of hold fashner nuts required suitable size fixed in brick wall, PVC connection pipe hot & coldfor Officers JCOs and OR Md Accn complete all as specified and as directed 238 Item No 213 : Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) 239 Item No 214 : Labour only for refixing the celing fan obtained from item No 5 above with replacement of unsv3 corePVC insulatedPVC sheated 3 core multistrandedcopper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal including over hauling the fan, painting of ceiling fans complete with two coats synthetic enamel paint by spraying including filling cavities with filler after cleaning all dust etc. complete all as specified and as directed. 240 Item No 215 : S & F for Highly efficient LED Bulbs, 15 W, used as a ready replacement for existing GLS/CFL direct fit lamp,in B-22 cap of make Bajaj, Havells, HPL complete all as specified and directed 241 Item No 216 : S & F for Decorative wall mounted light, gold finish fixture with white glass diffuserand provosion of LED bulb 9 watts complete all as specified and as directed. Make Havells Cat No LHFOAKD1TZ1D060 or its equvalent in Philips, Bajaj. 242 Item No 217 : S & F forLED tube light fitting 2 feet x 10 watts mirror type with high out put diffuser, decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cableof suitable sizefrom ceiling rose to fitting complete all as specified and as directed 243 Item No 218 : S & F for Energy saving new generation 10 watts LED bulk head fitting IP 65 luminaire with opel diffuser pre wired with warranty option of 5 years from date of installation andnecessary mounting arrangements , provision of new 3 core multistrandedcopper conductor of size 23/0.193 from ceiling rose to fitting including LED bulb complete all as specified and as directed. 244 Item No 219 : S & F for wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouputboxtype fitting, 230 volts and intregrated electronic driverconnector block etc with warranty option of 5 years from date of installation complete with all accessories internally pre wired andnecessary mounting arrangements, provision of new 3 core multistrandedcopper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed. 245 Item No 220 : S & F for Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 25/35 watts with pre wired andnecessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engineer- in-charge. 246 Item No 221 : S & F for energy efficient exhaust fan of 230 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan forconnection and making suitable size ofhole to existing brick wall for fan basecompelte all as specifiedand directed.(Note : Cost of suitable opening wall for fixing exhaust fan is deemed to be includedin overall rate quoted). 247 Item No 222 : S & F for PVC non-metallic rigid conduit ISI marked heavy duty white/ Ivory colour and its accessories heavy duty ISI marked of size 20 mm dia for LAN, telephone and TV connectionsincludingcutting, chasses and makinggooddisturbed surface to match with existing finish with plaster complete all as specified and directed. 248 Item No 223 : Supply, installation, commissioning and testing indoor type LT wall mounting Panel Board of minimum size 1.50 m (height) x 1.20 m (breath) x 0.30m (depth) factory made CPRI approved panel, weather, dust & vermin proof indoor, double door, front openable, including four comparment for fixing of four Nos Three phase KWH meter, one No single phase meter and MCB TPN and providing glass view for reading of meter and providing rubber/ PVC gasket of suitable size all sides of door, with copper busbar wrapped with PVC tape/ sleeves with maintained the colour code and copper strip/ wire busbar of suitable size to MCCB input and MCCB/ MCB output of suitable length for connection of cable from main busbar, made out of 2.00 mm thick mild steel CRCA sheet with suitable size angle iron supporting frame including applying two coats of Powder coated paint over a coat of red oxide zinc chrome primer over exposed external & internal surfaces suitable for 3 phase 4 wire system 415/440 volts grade including complete internal wiring with 10 sqmm copper wire and connections of all outgoing / incomming existing cable of any size complete all as directed by Engineer-in-Charge. (For Officers G+1 Md Accn) 249 INCOMMING(a) Copper strip busbar of size 30 x 5 mm wrapped with PVC sleeves with maintained the colour code and provision of making holes with Copper nuts, bolts & washers for cable connections including hydrograpic insulators with nuts & bolts at both ends= 04 nos. 250 (b)MCCBIP 44 and IP 66/67 protection, 4 pole, 415 volts, Lcu=25 KA breaking capacity, rating 100 Amps, adjustable thermal magnetic release including all fixing accessories with both ends spreader links -01 No.(c) Digital voltmeter of range (0-500) volts, flush mounting type with selector switch – 01 No(d)LED Neon indicator lamp (RYB) with holder,230/250 volts,AC -01 set (set of three) 251 OUTGOING(a) MCB, Tripple pole & neutral, 40 amps, 415 volts, ‘C’ curve, 10 KA allcomplete as specified and as directed - 4 Nos (Officers Accn)(b) MCB, single pole & neutral, 10 amps, 240 volts, ‘C’ curve, 10 KA allcomplete as specified and as directed - 1 No (Stair case lighting)(c) Fixing only serviceable existing electric meter- 01 No (obtained from item No 6) 252 (d) Smart Meter,AC,Three Phase Four Wire, Tamper Proof, Static Meter of Class 1.0, 415 V, 50 Hz, 10 A-60 A conforming to IS-16444 and relevant IEC standards with inbuilt 865-867 MHz Radio Frequency communication facility with self healing Mesh network with default and on demand display, billing data generation facility, anti-tamper features, Microprocessor and LED/LCD based circuitry. Meter Should support the following data : 30 min instantaneous data for voltage, current, power factor, power, cumulative energy and frequency, 30 load survey data for energy, monthly billing survey for Cumulative Energy and Max Demand. Meter should have connect / disconnect functionality operable compactable system from prepaid billing software in future. The meter should support open communication protocol DLMSwith the software- 04 Nos. Make:-Secure, L&T, Schneider. 253 Item No 224 : Supply, installation, commissioning and testing indoor type LT wall mounting Panel Board of minimum size 1.20 m (height) x 1.20 m (breath) x 0.30m (depth) factory made CPRI approved panel, weather, dust & vermin proof indoor, double door, front openable, including four comparment for fixing of five Nos single phase meter and MCB and porviding glass view for reading of meter and providing rubber/ PVC gasket of suitable size all sides of door, with copper busbar wrapped with PVC tape/sleeves with maintained the colour code and copper strip/wire busbar of suitable size to MCCB input and MCCB/MCB output of suitable length for connection of cable from main busbar, made out of 2.00 mm thick mild steel CRCA sheet with suitable size angle iron supporting frame including applying two coats of Powder coated paint over a coat of red oxide zinc chrome primer over exposed external & internal surfaces suitable for 3 phase 4 wire system 415/440 volts grade including complete internal wiring with 1.5 sqmm copper wire and connections of all outgoing / incomming existing cable of any size complete all as directed by Engineer-in-Charge. (For G+1 JCO, OR, Md Accn) 254 INCOMMING(a) Copper strip busbar of size 25 x 5 mm wrapped with PVC sleeves with maintained the colour code and provision of making holes with Copper nuts, bolts & washers for cable connections including hydrograpic insulators with nuts & bolts at both ends= 04 Nos. 255 (b)MCCBIP 44 and IP 66/67 protection, 4 pole, 415 volts, Lcu=25 KA breaking capacity, rating 63 Amps, adjustable thermal magnetic release including all fixing accessories with both ends spreader links -01 No.(c) Digital voltmeter of range (0-500) volts, flush mounting type of size 100mm x 100mm (4”x4”) square dial with selector switch – 01 Nos (Make : Legrand/Schneider/L&T)(d)LED Neon indicator lamp (RYB) with holder,230/250 volts,AC -01 set (set of three) Make :- AE/L&T 256 OUTGOING(a) MCB, Single pole & neutral, 40 amps, 240 volts, ‘C’ curve, 10 KA allcomplete as specified and as directed - 06 Nos 257 (b) Fixing only serviceable existing electric meter- 06 Nos (obtained from item No 6) 258 SCHEDULE A(Schedule of credit)Schedule of Credite Rs 109162.50.00 (Minus) inserted by the MES.(Note : Credit amount shall be deducted manually to arrive net bid amount)
