Tender For Repair/ Maint Of Plastering, Tiling, Plumbing, Joinery, Steel Work, Sheeting, Roof Treatment And Certain Misc Items At Restricted Area At Sg And Pts (Vikas) Sarsawa Under Ge (Af) Sarsawa.; 1 Taking down shutter of any description exceeding 1 Sqm and not exceeding 2 Sqm each complete all as specified and directed. 2 Taking down chowkhat or frame (without taking off shutter from the frame)not exceeding 1.5 Square Metre each , removing from the site including cutting holes required fortaking out existing hold fast etc. complete all as specified and directed. 3 Taking down chowkhat or frame (without taking off shutter from the frame) exceeding 1.5 Square Metre and not exceeding 04 Square Metre each, removing from the site including cutting holes required fortaking out existing hold fast etc complete all as specified anddirected. 4 M & L for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening complete all as specified and directed. 5 S & F Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement in the frame at site as per specification & drawing complete all as specified and directed. 6 S & F 35 mm thick IInd class hard woodGlazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc sizes of members of shutters as specified and directed. 7 M & L 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides compete all as specified and directed. 8 M & L for preparing of newuntreated wooden surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint (of approved shade) over a coat of pink primer complete all as specified and directed. 9 S&F stainless steelhinges 100mm long medium weightto pressed steel/angle iron frames by welding/ screws complete all as specified and directed. 10 S & F aluminium anodised barrel tower bolt 150mm size extruded section, ISI marked complete all as specified and directed. 11 S&F aluminium anodised barrel tower bolt 200mm size extruded section, ISI marked complete all as specified and directed. 12 S&F extruded aluminium alloy handles 150mm size fabricated type anodised ISI marked complete all as specified and directed. 13 S & F 300mm Aluminium alloy, anodised, sliding door bolt with hasp ,staple (bolt type) and fixingclips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. 14 S & F anodized aluminium frame with powder coating (minimumthickness 50 micron) and other sections for doors, windows, ventilators, partitions,with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. 15 S & F anodized aluminium door shutters, aluminium section weighing 0.55 kg/m, with power coating (minimumthickness 50 micron)including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodized aluminum snap beading screws etc. complete all as specified and directed. 16 S & F door closer hydraulically regulated, designation No. 2, aluminium (Die cast) body, universal type (ISI marked) suitable for door shutters of 701 to 850mm in width aand weight between 36 to 60 Kg and fixedcomplete all as specified and directed. 17 S & F anodized aluminium window and ventilator shutters, side hung or sliding type without sash bars, aluminium sections weighing minimum 0.55 kg/m, with power coating (minimumthickness 50 micron) including necessary joining cleats, glazing clips, rubber neoprene packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150mm long (1 No.), hinges type B-21 100mm long (2 Nos), suitable handle (1 No.) and any other accessories complete all as specified and directed. 18 S & F 5mm thick Sheet glass, ordinary quality, in squares exc 0.5 sq. m each pane complete all as specified and directed. 19 S & F 5mm thick Froasted glass in squares exc 0.5 sq. m each pane complete all as specified and directed. 20 S & F 5mm thick Tinted Coloured glass fixed to metal frame complete all as specified and directed. 21 S & F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples & screwed complete all as specified and directed 22 S & Fanodized aluminium grill with power coating (minimumthickness 50 micron) of approved pattern and fixed to the existing window/ventilatorframe with CP brass/stainless steel scrwed @ 200mm center to center, including cutting the grill to proper opening sizefor fixing and operation of handles and fixing approved anodised aluminium standard section around the opening as per requirement complete all as specified and directed. 23 Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed. 24 M & L for 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting /oiling to new putty to match with the existing/new surfaces complete all as specified and directed. 25 M & L for3mm thick froasted glass and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified and directed. 26 S & F in repair Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples & scrwed complete all as specified and directed. 27 S & F in repairs powder coated stainless steel drapery rod of 25 mm inner dia (in lengths as directed) of approved colour with & including decorative bowel at both ends and pair of powder coated mild steel brackets fixed at both ends with PVC rawl plug & steel screws on walls/beam, including PVC curtain rings of matching colour @ 10cm C/C complete all as specified and directed. 28 S & F in repairof venation blinds (super quality) to window openings complete all as specified and directed. 29 S & F in repair Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring. Fixed in floor overall length of cover plate 140mm complete all as specified and directed. 30 S & F in repair door seal bottom, door air gap rubber shield (Best Quality) Anti Rust, Brown/white/balck colour, Black Rubber complete all as specified and directed. 31 Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. 32 M & L for PCC (1:3:6) type C-2 (using 40mm graded broken stone aggregate) as in foundation after demolition of plain cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed. 33 M & L for Rolled sections (of angle, Tee, channel or any other section) as in framing for cladding, glazing, view cutter and the like fixed with angle cleats and connecting plates, etc of Fe-290 (Gde E-165) complete all as specified and directed. 34 M & L for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S 1161-1979 grade St.-240 complete all as specified and directed. 35 M & L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steelsheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete as specified and directed. 36 Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern in roof coverings complete all as specified and directed. 37 M & L for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof or wall covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. 38 M & L for Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof or wall covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. 39 M & L painting to new or previously untreated steel surfaces of any description over 10cm in width or girth with two coats of synthetic enamel paint over a coat of zinc chromic primer including preparation of surfaces. 40 Demolition of brick/stone masonry built in cement/lime mortar of any mix including all quoins pillar ashlars masonryand removal complete all as specified and directed. 41 M & L brick work sub class B bricks(OLD SIZE BRICKS) straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed. 42 M & L brick work sub class B bricks , (OLD SIZE BRICKS) straight or curved on plan to any radius in half brick thick wall, built in cement mortar (1:4) complete all as specified and directed. 43 Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed. 44 M & L rendering 15mm thick in cement mortar (1:6) on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified and directed. 45 M & L for rendering 15mm thick in cement mortar (1:4) on brick/stone wall surfaces on other than fair faces of brick work finished even and smooth without using extra cement with/without water proofing compound (water proofing compound wherever added shall be paid separately) complete all as specified and directed. 46 Supply only integral liquid water proofing compound (ISI marked) complete all as specified and directed. 47 M & L for 5mm thick rendering in cement mortar (1:3) on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified and directed. 48 M & L for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified and directed. 49 Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction complete all as specified and directed. 50 M & L for preparation of new plastered surfaces of walls and applying Two coats of 1st Quality acrylic distemper of approved tint over 1mm thick wall care putty complete all as specified and directed. 51 M & L for preparation of new plastered surfaces of walls and applying twocoats of weather proof exterior emulsion paint of approved tint over 1mm thick wall care putty complete all as specified and directed. 52 M & L for preparation of new plastered surfaces of ceiling and applying two coats of 1st Quality acrylic distemper of approved tint complete all as specified and directed. 53 Taking up or down 15mm steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and directed. 54 Taking up or down 20mm steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and directed. 55 S & F steel tubing medium grade 15mm bore with all fittings fixed complete to wall and or laid in floor complete all as specified and directed. 56 S & F steel tubing medium grade 20mm bore Medium grade fix to wall/floor fixed complete all as specified and directed. 57 S & F in repairvitreous china wash down water closet pan (Pedestal pattern), white (ISI marked), including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonoage pipe etc & with plastic WC seat cover (white) closed pattern with flat bottom and cover and suitable mild steel chromium plated or aluminised hinging device complete all as specified and directed. 58 S&F as in repair vitreous china wash down water closet pan One pices / Single Pices(Pedestal pattern EWC), coloured, floor mounted coupled closet, including connection to drain (or outgoing pipe), anti-sypohonage pipe etc, with & including WC seat cover coloured closed pattern with flat bottom and cover, CP jet nozzle, vitreous china symphonic action type twin flush flushing cistern of 10 litre capacity with lid, necessary fittings complete all as specified and directed. Make: “Cardiff Range” of Parrywareequivalent ofJaguar/ Roca/Kohler/M/S Johnson, H & R India Ltd /M/S Hindustan sanitary ware and Industries Ltd / CERA, Madhusudan Ceramic 59 S & F as in repair vitreous china squatting pan of orrisa pattern long pan size 580mm white (ISI marked) with P or S trap, front or back inlet and foot rest any pattern, including connection to flushing pipe anti-syphonage pipe etc, including setting of pan & trap in lean PCC (1:5:10) complete and making good to distrubed floor with PCC or cement mortar (1:3) to match with sorroundings complete all as specified and directed. 60 S & F in repairs Jet spray chromium plated brass for EWC with & including PVC connection 600 mm long suitable for 15 mm bore GI pipe with PTMT nut & nipple complete all as specified and directed. 61 S & F in repairs PVC low level flushing cistern 10 litrs capacity (white ISI marked) with inlet ball valve,float and handle, syphonic action type including brackets and flush pipe of polythelene of low or high density of PVC 32mm dia complete all as specified and directed. 62 S & F in repairs PVC connection of 15mm bore with2 Nos. PTMT nuts, 60cm long fixed with one end to pillar tap & the other end to stop cock or iron pipe complete all as specified and directed. 63 S & F in repair towel rails of 20mm dia tubular brass chromium plated 60cm long D type fixed complete all as specified and directed. 64 S & F in repairs MS grating CP 100mm dia, with hole/without for waste pipe of approved make including fixing with CM to floor/nahani traps etc complete all as specified and directed. 65 S & F in repair fancy typer Pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or withoutlettered Hot or Cold with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore complete all as specified and directed. 66 S & F in repairs brass chromium plated shower rose 125mmx125mm size with swivel joint type including fixing to steel pipe of 15mm bore or union complete all as specified and directed. 67 S & F in repairs looking mirror 600x450mm bevelled edge 5.5mm thick selected quality glass, mounted on 6mm thick commercial ply, aluminium frame around and fixed to wooden plug with CP brass screws and cup washers complete all as specified and directed. 68 S & F in repair fancy typebib taps, chromium plated alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. 69 S & F in repair fancy type angle/stop valves, chromium plated alloy screwed down high presure, screwed both ends for iron pipe or for unions of 15 mm dia long sunk concealed type complete all as specified and directed. 70 S & F in repairs CP brass (fancy type) wash hand basin mixer 15mm diaincluding joints to steel pipe or unions complete all as specified and directed. 71 S & F in repairs Brass CP Wallmixer(Non Telephonic Type) with L bend 3-in-1 for mixing hot & cold water screwed down for iron pipe15 mm bore and fixed complete all as specified and directed. 72 S & Fin repair chromium plated Brass health faucet for EWC with including flexdible pipe minimum 1m long suitable for 15mm borewith all connected fittings complete all as specified and directed. 73 S&F in repairs 32/40mm dia PVC flexible waste pipe 80cm long withsocket for union, for WHB/urinal/sink complete all as specified and directed. 74 S&F in repairs vitreous china wash basin white, flat back, size 550x400mm including waste coupling brass CP 32mm bore, and 02 Nos CI brackets complete all as specified and directed. 75 Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thickness (below or above ground level.) & removing unserviceable materials in low laying area, complete all as specified and directed. 76 M & L for 25 thick cement concrete (1:2:4), type B-1 (using 20mm graded crushed stone aggregate) as in levelling coarse for tiles complete all as specified and directed. 77 Dismantling floor, hearth or wall tiling incl cement mortar bedding (but ot backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. 78 M & L for vitrified ceramic tiles 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar (1:6) complete all as specified and directed. 79 M & L for coloured non skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar (1:6) complete all as specified and directed. 80 M & L for vitrified ceramic tiles 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, on vertical surfaces such as dado, skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick screed bed in cement & sand mortar (1:4) complete all as specified and directed. 81 M & L for Glazed ceramic coloured tiles in vertical surface450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles and over 10 mm thick rendring in cement mortar (1:4) complete all as specified and directed. 82 M & L for Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15mm thick screed bed cement mortar (1:6) complete all as specified and directed. 83 Dismantling water tanks of capacity exc 250ltr but not exc 500ltr and removing from site complete all as specified and directed. 84 S & F 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc.as specified in SSR Part-I complete all as specified and directed. 85 M & L for 100mm thick Cement concrete type D- 2, (1:4:8) (using 40mm graded aggregate) as in sub base complete all as specified and directed. 86 M & L for pre-polished cement concrete chequered tiles of size 300mm by 300mm by 25 mm thick, any shape of any tint, heavy duty, set jointed and pointed with grey cement slurry@ 2.5 Kg per square metrecomplete all as specified and directed. 87 M & L for Machine pressed precast concrete interlocking paver block (with grey cement and pigment) any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade over & including 50mm thick sand cushioning complete all as specified and directed. 88 Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed. 89 Dismantling false ceiling grid any type complete all as specified and directed. 90 S & F 5mm thick prelam PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining, Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of Solvent Cement and fixing at site complete all as specified and directed. 91 M & L for false ceiling made out of E-board classic of size 595 x 595 x 4 mm thick, GI frame consisting of main Tee of size 38.50 x 24.00 mm and cross Tee of size 28.50 x 24.00 mm thick made out of PGI sheet 0.30 mm thick doubled at web and single at flange, flange covered with poder coated sheet 0.25 mm thick and angle 24.00 x 24.00 x0.4 mm thick powder coated suspended with GI wire 3 mm dia and up to 2 Mtrs long complete including plugging fixing of angle to brick walls with steel rawl plugs @ 450 mm c/c complete all as specified and directed. 92 Demolition Mud phuska on roofs, any thickness, including plastering, existing tretement and brick tiles (whether full thickness removed or only or part there of)etc and removal of debris & rubbish off the premises to a distance exc 1 Km but not exc 1.5 Km complete all as specified and directed. 93 M & L for providing cement concrete intype B0 1:2:4 (using 12.5 mm graded crushed stone aggregate) as in roof padding,laid to(consolidated thickness 65mm or less) as leveling course, laid and compacted inmin slope 1:30 over roof complete all as specified and directed. 94 M & L screed laid 10mm thick in cement mortar (1:4) with water proofing compound over green concrete surface(WPC will be measured and paid seperately) surface finished even and smooth (without using extra lime or cement) complete all as specified and directed. 95 M & L for roof treatment using APP based polymeric membrane minimum weighing not less than 3kg/sqm black finish reinforced with non woven polyster matt with thermo finish (wt. not less than 150 gms/sqm) laid over compatible bitumen primer @0 .30 liters per sqm and bitumen 85/25 @ 1.20 Kg per Sqm with help of torching with a proplyne or a butane gas using torch with minimum overlap of 75mm at side and 100mm at ends and sealing including applying a coat of bitumen primer & bitumen 85/25 applied hot all as per manufacturer instructuions. For parapet in a groove (No separate payment will be made and measurement will be done for horizontal surfaces) including applying a coat of heat repallant bitumen aluminium paint @ 0 .1 liter per Sqm on topof treated surface of roof complete all as specified and directed.
