Tender For Repair/Maintenance Of Roof Sheet, Plaster, Brick Work, Tiling, Sanitary Fitting, Joinery And Misc Works At Arc Sarsawa Under Ge (Af) Sarsawa.; 1 Taking down shutter of any description exceeding 1 Square Metre and not exceeding 2 Square Metre each complete all as specified and directed. 2 Taking down chowkhat or frame (without taking off shutter from the frame)not exceeding 1.5 Square Metre each , removing from the site including cutting holes required fortaking out existing hold fast etc complete all as specified and directed. 3 Taking down chowkhat or frame (without taking off shutter from the frame) exceeding 1.5 Square Metre and not exceeding 04 Square Metre each , removing from the site including cutting holes required fortaking out existing hold fast etc complete all as specified and directed. 4 S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed. 5 S & F Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed. 6 S & F 35 mm thick IInd class hard woodGlazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); supplied and fitted to chowkats complete all as specified and directed.Note: Door shutter width not exc 0.85mwith single shutter each door but door shutter width exc 0.85m two panel shutter each doorwithout any extra cost. 7 M & L for 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides compete all as specified and directed. 8 S & F in repair 35 mm thick IInd class hard woodGlazed and skeleton window, ventilator, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (b) complete all as specified and directed. 9 M & L for preparing of newuntreated wooden surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint (of approved shade) over a coat of pink primer complete all as specified and directed. 10 M & L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steelsheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete & making good the floors/wallsin PCC 1:2:4 type B-0 to match the existing floors/walls complete all as specified and directed. 11 M & L forclamps , hold fasts; wall ties, plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts plate washers and similar small articles conforming to Fe-290 Gde-E-165 ® complete all as specified and directed. 12 S & F IInd class hard wood plain solid straight chowkat and frame wrought framed rebatted on the solid rounded or chamfered put together with glue pinned at joint complete complete all as specified and directed. 13 S & F stainless steelhinges 100mm long medium weightto pressed steel/angle iron frames by welding/screws complete all as specified and directed. 14 S & F aluminium anodised barrel tower bolt 150mm size extruded section, ISI marked & fixed complete all as specified and directed. 15 S & F aluminium anodised barrel tower bolt 200mm size extruded section, ISI marked & fixed complete all as specified and directed. 16 S & F extruded aluminium alloy handles 150mm size fabricated type anodised ISI marked complete all as specified and directed. 17 S & F 300mm Aluminium alloy, anodised, sliding door bolt with hasp ,staple (bolt type) and fixingclips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. 18 S & F anodized aluminium frame with power coating (minimumthickness 50 micron) and other sections for doors, windows, ventilators, partitions,with one or more rebates including joining cleat for fixing etc complete all as specified and directed. 19 S & F anodized aluminium door shutters, aluminium section weighing 0.55 kg/m, with power coating (minimumthickness 50 micron)including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodized aluminum snap beading screws etc. complete all as specified and directed. 20 S & F anodized aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m,with power coating (minimumthickness 50 micron)including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150mm long (1 No.), hinges type B-21 100mm long (2 Nos), suitable handle (1 No.) complete all as specified and directed. 21 Supply only 5mm thick Sheet glass, ordinary quality, in squares n exc 0.5 sq. m each pane complete all as specified and directed. 22 Supply only 5mm thick Froasted glass in squares n exc 0.5 sq. m each pane complete all as specified and directed. 23 Supply only5mm thickTinted Coloured glass fixed to metal frame complete all as specified and directed. 24 S & F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples & screwed complete all as specified and directed. 25 S & Fanodized aluminium grill with power coating (minimumthickness 50 micron) of approved pattern and fixed to the existing window/ventilatorframe with CP brass/stainless steel scrwed @ 200mm center to center, including cutting the grill to proper opening sizefor fixing and operation of handles and fixing approved anodised aluminium standard section around the opening all complete as per requirement complete all as specified and directed. 26 S & F in repair for 18/19mm thick High Density High Moisture Resistant board (HDHMR) Prelaminated both sides as in Controllers Desk ,palmed boxes,showcase,shutters of Cup Boards etc including 6mm designing teak wood beading on edges complete all as specified and directed. 27 S & F 75mm extruded brass handles, fabricated type polished complete all as specified and directed. 28 S & F Width of flaps (when open) 30mm Continuous (piano) hinges, mild steel, bright finish or electro galvanised complete all as specified and directed. 29 S & F FAST DM01SS Stainless Steel Furniture Door Catcher Magnet Size No. 2 for for Wadrobe, Cupboard and Almirah Door. (SS MAT)with Mounting Screw complete all as specified and directed. 30 Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed. 31 M & L for 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified and directed. 32 M & L for3mm thick froasted glass and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified and directed. 33 S & F in repair Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples & screwed complete all as specified and directed 34 S & F in repairs powder coated stainless steel drapery rod of 25 mm inner dia (in lengths as directed) of approved colour with & including decorative bowel at both ends and pair of powder coated mild steel brackets fixed at both ends with PVC rawl plug & steel screws on walls/beam, including PVC curtain rings of matching colour @ 10cm C/C complete all as specified and directed. 35 S & F in repairs door closer hydraulically regulated, designation No. 2, aluminium (Die cast) body, universal type (ISI marked) suitable for door shutters of 701 to 850mm in width aand weight between 36 to 60 Kg and fixed complete all as specified and directed. 36 S & F in repairfor double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty, fixed in repairs, with & including replacement of floor tiles if any broken during repair work and making good disturbed surfaces matching to the existing surfaces complete all as specified and directed. 37 S & F in repairs brass mortice lock, vertical type, size 100mm, 4 Levers with escutcheon plates & two keys fixed in aluminium frame complete all as specified and directed. 38 S & F in repairof venation blinds (super quality) to window openings complete all as specified and directed. 39 S & F in repairplastic net fencing of mesh size not exc 32 x 32 mm and thickness not less than 4mm fixed to steel or wooden posts as per manufacturers instructions complete all as specified and directed. 40 Repairs to Steel window/ventilator any type & any size by taking down Shutter, replacing defective hinge,handle & locking arrangement including necessary welding(if any) and resecuringfixed to framecomplete all as specified and directed. 41 Resecuring or easing & adjusting, without taking down shutter of any description exc 1 sqm and not exc 2 sqm each complete all as specified and directed. 42 S & F in repair 150mm long aluminum anodised handle complete all as per IS complete all as specified and directed. 43 S & F in repair 200mm long aluminum anodised Pull handle complete all as per IS complete all as specified and directed. 44 S & F in repairs 150mm long aluminum, anodized barrel tower bolts of extruded section complete all as specified and directed. 45 S & F in repairs 200mm long aluminum, anodized barrel tower bolts of extruded section complete all as specified and directed. 46 S & F in repair 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixingclips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. 47 S & F in repair stainless steelhinges 100mm long medium weightto pressed steel/angle iron frames by welding/screws complete all as specified and directed. 48 S & F in repair Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring. Fixed in floor Overall length of cover plate 140mm complete all as specified and directed. 49 S & F in repair DOOR SEAL BOTTOM, DOOR AIR GAP RUBBER SHIELD (Best Quality) Anti Rust , Brown/white/balck colour, Black Rubber complete all as specified and directed. 50 S & F in repairFAST DM01SS Stainless Steel Furniture Door Catcher Magnet Size No. 2 for for Wadrobe, Cupboard and Almirah Door. (SS MAT)with Mounting Screw complete all as specified and directed. 51 S & F in repair anodized aluminium grill with power coating (minimumthickness 50 micron) of approved pattern and fixed to the existing window/ventilatorframe with CP brass/stainless steel scrwed @ 200mm center to center, including cutting the grill to proper opening sizefor fixing and operation of handles and fixing approved anodised aluminium standard section around the opening all complete as per requirement complete all as specified and directed. 52 S & F in repair 0.56mm thick aluminum sheet fixed with nails to door shutter complete all as specified and directed. 53 Dismantling plain or corrugated sheet sheeting, any gauge, thickness, including nainital or similar pattern roof coverings complete all as specified and directed. 54 M & L for Pre- painted galvatume aluminum zinc coating GI based Semi-corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screwscomplete all as specified and directed. 55 M & L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specifiedcomplete all as specified and directed. 56 M & L Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S 1161-1979 grade St.-240complete all as specified and directed. 57 M & L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement compete all as specified and directed. 58 M & L painting to new or previously untreated steel surfaces of any description over 10cm in width or girth with two coats of synthetic enamel paint over a coat of zinc chromic primer including preparation of surfacescomplete all as specified and directed. 59 M & L for Cutting openings, through brick walls for door, window and other openings or enlarging existing openings.converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc.. to store and rubbish not exc. 50m complete all as specified and directed. 60 Forming jambs, etc., to openings (to foregoing item), with stone supplied by MES including cutting, toothings and properly bonding into old work, including facing and pointing (if necessary) to match existing work,complete all as specified and directed. 61 Demolition of brick/stone masonry built in cement/lime mortar of any mix including all quoins pillar ashlars masonry and removalcomplete all as specified and directed. 62 M & L brick work sub class B bricks(OLD SIZE BRICKS) straight or curved on plan exc 6 mtr mean radius built in cement mortar (1:6) complete all as specified and directed. 63 M & L brick work sub class B bricks , (OLD SIZE BRICKS) straight or curved on plan to any radius in half brick thick wall, built in cement mortar (1:4) complete all as specified and directed. 64 Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etccomplete all as specified and directed. 65 M & L rendering 10mm thick in cement mortar (1:6) on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified and directed. 66 M & L for rendering 15mm thick in cement mortar (1:4) on stone wall surfaces or other than fair faces of brick work & surfaces finished even and smooth without using extra cement with water proof compoundcomplete all as specified and directed.Note: water proof compound will be paid separately. 67 Supply only integral liquid water proofing compound (ISI marked)complete all as specified and directed. 68 M & L rendering 5mm thick in cement mortar (1:3) on concrete surfaces in ceiling, finished even & smooth without using extra cementcomplete all as specified and directed. 69 M & L for preparation of new plastered surfaces of walls and applyingtwo coats of 1st Quality acrylicdistemper of approved tint complete all as specified & directed by Engr-in-Charge. 70 M & L for preparation of old /newly BRICK, STONE, CONCRETE, ASBESTOS CEMENT SHEET OR PLASTER Surfaces of any description over 10cm girth or width, not otherwise described and applying twocoats of weather proof exterior emulsion paint complete all as specified and directed. 71 M & L for preparation of old painting work, stone, concrete, asbestos cement sheet or plaster surfaces of any description over 10cm girth or width, not otherwise described and applying one coat of wheather proofExterior Emulsion Paint (exterior grade) complete all as specified and directed.Note: The rate quoted by tenderer is deemed to included in item for painting any type of Bldgs for married/OTM accn , stores, all type fencing/Gates including any height and widthshall be made good by contractor without any extra cost to the Govt. 72 M & L for preparation of newly plastered/unplasteredsurfaces of ceilings & applying two coats of oil bound distemper (OBD)complete all as specified and directed. 73 M & L forpreparation of old decorated surfaces of wallsand applying one coat of oil emulsion distemper (OBD) of approved shade/tint complete all as specified and directed. 74 M & L forpreparation of old decorated surfaces of wallsand applying two coats of 1st Quality acrylicdistemperof approved shade/tint complete all as specified and directed. 75 M & L for exterior or interior waterproof/weather proof cement based1 mm thick puttyonnew plastered/old surfacewall after scrapping to prepare the surface even and smooth complete all as specified and directed. 76 M & L forpreparation of old decorated plastered/unplastered surfaces of ceilings & applying one coats of oil bound distemper (OBD) complete all as specified and directed. 77 M & L preparation of old painted surfaces of wood and wood based material of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. 78 M & L preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. 79 Taking up or down 15mm steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and directed. 80 Taking up or down 20mm steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and directed. 81 S & F steel tubing medium grade 15mm bore with all fittings fixed complete to wall and or laid in floor complete all as specified and directed. 82 S & F steel tubing medium grade 20mm bore Medium grade fix to wall/floor fixed complete all as specified and directed. 83 S & F in repairvitreous china wash down water closet pan (Padestal pattern), white (ISI marked), including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonoage pipe etc & with plastic WC seat cover (white) closed pattern with flat bottom and cover and suitable mild steel chromium plated or aluminised hinging device complete all as specified and directed. 84 S & F in repair32mm dia waste fitting (waste coupling) brass chromium plated for glazed ware sink, basin etc with long screwed shanks and fly nuts flange complete for the following sizes complete all as specified and directed. 85 S & F in repairs Jet spray chromium plated brass for EWC with & including PVC connection 600 mm long suitable for 15 mm bore GI pipe with PTMT nut & nipple complete all as specified and directed. 86 S & F in repairs PVC low level flushing cistern 10 litrs capacity (white ISI marked) with inlet ball valve,float and handle, syphonic action type including brackets and flush pipe of polythelene of low or high density of PVC 32mm dia for LLFC make Dolfine/Commander Champion complete all as specified and directed. 87 S & F in repairs PVC connection of 15mm bore with2 Nos. PTMT nuts, 60m long fixed with one end to pillar tap & the other end to stop cock or iron pipe complete all as specified and directed. 88 S & F in repair towel rails of 20mm dia tubular brass chromium plated 60cm long D type fixed to complete all as specified and directed. 89 S & F in repairs MS grating CP 100mm dia, with hole/without for waste pipe of approved make including fixing with CM to floor/nahani traps etc complete all as specified and directed. 90 S & F in repairs fancy typer Pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or withoutlettered Hot or Cold with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore complete all as specified and directed. 91 S & F in repairs brass chromium plated shower rose 125mmx125mm size with swivel joint type including fixing to steel pipe of 15mm bore or union complete all as specified and directed. 92 S & F in repairs looking mirror 600x450mm bevelled edge 5.5mm thick selected quality glass, mounted on 6mm thick commercial ply, aluminium frame around and fixed to wooden plug with CP brass screws and cup washeres complete all as specified and directed. 93 S & F in repair fancy typebib taps, chromium plated alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. 94 S & F in repairStop valves, 15mm bore cast copper alloy,screwed down,high pressure,with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. 95 S & F in repair fancy type angle valves, chromium plated alloy screwed down high presure, screwed both ends for iron pipe or for unions of 15 mm dia long sunk concealed type complete all as specified and directed. 96 S & Fin repair chromium plated Brasshealth faucet for EWC with including PVC Connection 1m long suitable for 15mm borewith all connected fittings as approved complete all as specified and directed. 97 S & F in repairs 32/40mm dia PVC flexible waste pipe 80cm long withsocket for union, for WHB/urinal/sink complete all as specified and directed. 98 S & F in repairs Sink Coupling including PVC flexible waste pipe 80cm long with socket for union complete all as specified and directed. 99 S & F as in repair sinks with drainage boardof overall size 915mm x 460mm bowl size 410mm x 330mm x 160m made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe complete all as specified and directed. 100 S & F in repairs vitreous china wash basin white, flat back, size 550x400mm including pillar tap brass CP 15mm bore with long screwed shanks and fly nuts waste coupling brass CP 32mm bore, flange end bedded in red lead cement and other end fixed and PVC connection 450mm long 15mm bore with 2 Nos nuts and washes CI brackets complete all as specified and directed. 101 Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thickness (below or above ground level.) & removing unserviceable materials in low laying area complete all as specified and directed. 102 M & L for 25 thick cement concrete (1:2:4), type B-1 (using 20mm graded crushed stone aggregate) as inlevelling coarse for tiles complete all as specified and directed. 103 Dismentling floor , hearth or wall tiling incl cement mortar bedding (but ot backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. 104 M & L for vitrified ceramic tiles 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar (1:6) complete all as specified and directed. 105 M & L for coloured non skid ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar (1:6) complete all as specified and as directed. 106 M & L for vitrified ceramic tiles 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick screed bed in cement & sand mortar (1:4) complete all as specified and as directed. 107 M & L Glazed ceramic coloured tiles in vertical surface450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles and over 10 mm thick rendring in cement mortar (1:4) complete all as specified and directed. 108 M & L for Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, windowcills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15mm thick screed bed cement mortar (1:6) complete all as specified and directed. 109 M & Lfor 18/19mm thickMachine cut udaipur green marble (of any type) work (table rubbed and polished) in steps, jambs, pillars, windowcills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15mm thick screed bedcement mortar (1:6) complete all as specified and directed.
