Provn Of Two Additional Room Size 12 X 15 Along With Attached Latrine/ Bathroom In Local Audit Office (Army), Gwalior Under Ge Gwalior; 1 M&L for 75 mm thick cement concrete 1:3:6 type C-2 using 40 mm graded crushed stone aggregate as in plinth protection and path laid in panels, not more than 3 RM in length or change in direction, laid to slope 1:30 including forming joints 10mm wide and duly filled with mastic bitumen (One part bitumen mixed with three parts of sand) surface, complete all as specified and as directed.Note : Quoted rates are deemed to be inclusive of jointing material against form work and joint fillings.) 2 Surfaces dressing not exceeding 15cm deep and getting out in soft/loose soil complete all as specified & directed. 3 Surface excavation not exceeding 30cm and averaging 15 cm deep and getting out in soft/loos soil complete all as specified and directed. 4 Excavating in trenches, not exceeding 1.5 mwide and not exceeding 1.5 m in depth; forfoundation etc or for shafts, wells, cesspits, manholes, pier holes, etc not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out in soft/loose ofsoil complete all as specified and directed. 5 Excavating in trenches, not exceeding 1.5 mwide and not exceeding 1.5 m in depth; forfoundation etc or for shafts, wells, cesspits, manholes, pier holes, etc not exceeding 10 Sqm on plan and exceeding 1.5 Sqm & not exceeding 3 m in depth and getting out in soft/loose ofsoil complete all as specified and directed. 6 Returning, filling with approved earth including spreading, levelling, watering and well ramming in layers not exceeding 25 cm depth complete all as specified and directed. 7 Removing excavated material upto50m & depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed. 8 M&L Treating the botton and sides of excavation at the rate of 5 litres of emulsion per Sqm of surface area complete all as per specified and dirceted. 9 M&L Treating the backfill contact with foundation at the rate of 7.5 liters of emultion per Sqm of vertical surface (Area of Sub Structure in contact with backfill to be measured)complete all as per specified and dirceted. 10 M&L Treating the topsurface of filled at therate of 5 litres of emulsion per Sqm of surface area complete all as per specified and dirceted. 11 M&L Treating thesoil under plinth protection at therate of 5 litres of emulsion per Sqm of surface area complete all as per specified and dirceted. 12 M&L Plain cement concrete 1:3:6 type C-2 using 40 mm graded crushed stone aggregate as in foundations / filling in mass concrete complete all as specified.and directed. 13 M&L providing M-25 Design mixusing 20 mm graded crushed stone aggregate as in Foundations, including rafts,footings, foundationbeams;plinthbeams;baseforcolumnsetcbasementslabs, under-reamed piles and mass concrete complete all as specified and directed. 14 M&L forproviding M-25 Design mixusing 20 mm graded crushed stone aggregate as in Roof beam, lintel band, cantilevers bressummers, lintels over 1.5m spanetc complete all as specified and directed. 15 M&L for providing M-25 Design mix using 20 mm graded crushed stone aggregateas incoloumn, pillars, piers, posts and struts etccomplete all as specified and directed. 16 Form work to sides of concerte foundation, footings, base of columns, raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work vertical or to batter for rough finish concrete surface complete all as specified & directed. 17 Form work to Columns, square or rectangular, rough finish surfaces of concrete complete all as specified and directed. 18 Form work to side and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc also splays between floors and beam etc for rough finish concrete surface complete all as specified & directed. 19 Material & Labour mild steel TMTbars 8-10mm dia asinstirrups, spacers andbinders,cut tolength,benttoshaperequired,includingcranking,bendingspirallyfor hooping forcolumns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 20 Material & Labour mildsteelTMT bars10mmdiaandover,cuttolength,benttoshaperequired,including cranking, bendingspirally forhoopingforcolumns,hookingendsandbindingwithand including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 21 M&L for Moorum / red bajri filling in floors or pavings, laid in layers not exceeding 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed. 22 M&L for brick work with fly ash (old size) bricks, straight or curved on plan exceeding 6m mean radius, built in CM 1:6below complete all as specified and directed. 23 M&LRendering15mmthickonfairfacesofbrick or concerte surfacesincementmortar(1:4)finished evenandfair complete all as specified & directed. 24 Material & Labour for providingandfixinginposition, outer walls 170mmthickfactory madeExpandedPolystyreneCore(EPSCore)wallpanels consistingofEPScoresand-wichedbetweentwo Engineered sheets of welded wire fabric mesh duly finishedwithshortcretematerialsonouterfaces.The fabric mesh shall be made of 2.5 mm dia GI wire mesh with 50mmpitchinboththedirectionsandonbothfacesof thewall .TheEPScore shall consist of 100 mm thick EPS of density not less than 15 Kg/ Cum, Both the outer faces of the panel shall be finishedbyapplyingthelayerof35mmthickcement mortar1:3{1cement:3coarsesand(nothavingmore than 40% stone chips of size upto 6 mm)}with the help ofshot creting/gunitingequipment atapressurenot lessthan1bar(100KN/Sqm)andbothsurfacesfinished withtrowel.Fixing operationsof wallpanels shallbe completed in all respect as per direction and specifications and under the overall decision of EPS panel manufactures, the manufactures shall give complete 2D plan design, structural design, 3D model design before commencement of work .The panel manufacturer should have BMPTCvalid Performance apprasial certificate complete all as specified and directed. 25 Material & Labour for Providingandfixinginposition,inner walls 150mmthickfactory madeExpandedPolystyreneCore(EPSCore)wallpanels consistingofEPScoresand-wichedbetweentwo Engineered sheets of welded wire fabric mesh duly finishedwithshortcretematerialsonouterfaces.The fabric mesh shall be made of 2.5 mm dia GI wire mesh with 50mmpitchinboththedirectionsandonbothfacesof thewall .TheEPScore shall consist of 80 mm thick EPS of density not less than 15 Kg/ Cum. Both the outer faces of the panel shall be finishedbyapplyingthelayerof35mmthickcement mortar1:3{1cement:3coarsesand(nothavingmore than 40% stone chips of size upto 6 mm)}with the help ofshotcreting/gunitingequipment atapressurenot lessthan1bar(100KN/Sqm)andbothsurfacesfinished withtrowel.Fixing operationsof wallpanels shallbe completed in all respect as per drawings and specifications and under the overall direction of EPS panel manufactures, the manufactures shall give complete 2D plan design, structural design, 3D model design before commencement of work .The panel manufacturer should have BMPTCvalid Performance apprasial certificate complete all as specified and directed. 26 Material & Labour for Providing and fixing in position for roof 185 mm thick factory made Expanded Polystyrene Core (EPS Core) roof or floor panels made of 2.5 mm dia GI wire mesh with 50 mm pitch in both the directions and on both faces of panel, EPS core shall consist of 100 mm thick EPSofdensitynotlessthan15Kg/ CumThebottom side of the panel shall be finished by applying a layer of 35 mm thick cement mortar 1: 3 {1 cement: 3 coarse sand (nothavingmorethan40%stonechipsof size upto 6 mm)} withthehelp of shotcretingequipmentata pressureofnotlessthan1bar(100KN/Sqm)andsurface finishedwithtrowel.Topfaceofthepanelshallbe provided and finished by applying 50 mm thick layer of cementconcrete1:1.5:3(1cement: 1.5coarsesand:3 parts graded crushed stone aggregate 20 mmnominalsize)including neassary support for EPS panel / concerete. Fixing operationsofroof / floorpanels shall be completedinall respect as per drawings and specifications and under the overall direction EPS panel manufactures, the manufactures shall give complete 2D plan design, structural design, 3D model design before commencement of work .The panel manufacturer should have BMPTC, valid Performance apprasial certificate complete all as specified and directed. (Quoted Rates for shuttering for support includeing in the unit quoted rate) 27 M&L for mild steel section rectanglur pipes (SHS) for coloumns, beamsas in frame for buildingcomplete all as specified and design given by EPS panels manufacturer. 28 S&F steel mesh 50mmx50mmx2.5mm thick fixed with EPS Panels at Corner junctions and other locations as in I mesh, L mesh, C mesh complete all as specified and directed. 29 M&L Polypropylene construction Fiber complete mixed with concerete @ 1Kg/Cum complete all as specified and directed. 30 Supply & fixing factory made uPVC white colour fixed glazed window / ventilator made of (small series) frame 47x50 mm mullion 47x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of approriate dimention (Area upto 0.75 Sqm) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.6±0.20 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, GI fasteners 100x 8 mm size for fixing frame to finished walls, plastic packers, plastic caps and necessary stainless steel scews etc Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of hole for fixing hardweres and drainage of water etc after fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved best quality,complete as approved by GE. 31 Supply & Fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm ±0.2 mm) Window profile with hollow section with multi-chamber. Frame (88 mm x 52 mm), sliding sash (42mm x 67 mm) Slinding mesh Sash (42mm x 57 mm) Sliding interlock (One vertical length in each shutters) (45.5 mm x 28 mm), Glazing beat (24.5 mm x 16 mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of rain water etc making arrangement for fixing of hardware EPDM gasket, 1.2±0.2 mm thick galvanised steel Frame (30 mm x 18 mm) 2 nos, sliding sash (30 mm x 18mm), sliding mesh sash (26 x 10 mm) profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners, (Hardware : Touch Lock of zinc alloyed (white powder coated), steel roller system Stainless steel wire mesh/cloth 0.36 mm nominal dia of wire and average width of aperture 1.4 mm and required accessories).Note : The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose) 32 S&F floor door spring for glass doors Double action floor springhydraulically regulated made up of minimum 1.25 mm thickaluminium alloy sheetfoundation box, main body with stainless steel cover,governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed. 33 Material & Labour for anodised aluminium door shutters, aluminium section weighing 0.55 Kg/ RM including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, butt hinges, anodised aluminum snap beading fixed with steel screws complete all as specified & directed. 34 Supply & Fixing Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixingand Powder Coating minimum thickness 0.5mm thick fixed with fasteners complete all as specified & directed. 35 Supply & Fixing solid PVC door frame of size50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube fixed in opening as per specification & drawings complete all as specified and as directed. 36 Supply & Fixing factory made solid panel PVC door shutter 30mm thick (style) consisting to framemade with MS tubes for top & bottom rails; MS frame shall be covered with heat moulded plain colour PVCCchannel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Penelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawings complete all as specified and directed. 37 Supply & Fixing aluminium butt hinge 100mm size fixed with steelscrews complete all as specified & directed. 38 Supply & Fixing Extruded aluminium alloy handle of 150 mm size fabricatedtype anodised fixed with steel screws complete all as specified & directed. 39 Supply & Fixing aluminium anodised barrel tower bolt of 200mm extruded section fixed with steel screws complete all as specified & directed. 40 Supply & Fixing floor door stopper of cast aluminium body and tongue, over all length of cover plate 150 mm anodized with hard drawn steel springfixed to door shutters complete all as specified and directed. 41 Material & Labour preparation of new steel surface of any description exceeding 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer on entire steel surface complete all as specified and directed. 42 Supply & Fixing 4 mm thick tinted glassof selected qualityin square not exceeding 0.5 Sqm in each pane, fixed to aluminumframe with and including suitablerubber beadingcomplete all as specified and directed. 43 Supply & Fixing 4 mm thick tinted glassof selected qualityin squareexceeding 0.5 Sqm in each pane, fixed to aluminumframe with and including suitablerubber beadingcomplete all as specified and directed. 44 Supply & Fixing Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mmand fixed with tinned tacks or galvanisedstaples complete all as specified and directed. 45 Supply & Fixing Curtain rod stainless steel decorative type 25 mm dia (OD) including fixing bracket and end knobs fixed with steel screws on walls complete all as specified and directed. 46 Material & Labour for plain cement concrete 1:4:8 type D-2 using 40 mm crushed stone aggregate as in foundation filling and mass concrete or bed of hard standing or paver blocks complete all as specified and directed. 47 Material & Labour Hard core of gauge 40-63 mm deposited, spread and levelled in layers not exceeding 15 cm thick, watered and well rammed to a true surface for broken stone or bouldess complete all as specified & directed. 48 Material & Labour 25 mm thick PCC 1:2:4 type B-0 using 12.5 mm crushed stone aggregate as levelling course / mass concrete or used as bed plates, coping/benching or kerbs complete all as specified and directed. 49 Material & Labour 8-10mm thick Double charged Vitrified light shade coloured and printed designer tiles (Square or Rectangular) area of each tiles exceeding 0.42 Sqm but not exceeding 1 Sqm as in flooring over and including 15 mm thick cement screed bed or bedding in (1:6) CM set and jointed in neat cement slurryand pointed in white cement mixed with colour to match the shade of tiles complete all as specified and directed. 50 Material & Labour 8-10 mm thick double charged Vitrified light shade coloured and printed designer tiles of width as directed as in dado or skirtingfixed over and including 10 mm thick cement rendering to recived thae tiles in (1:4) CM set and jointed in neat cement slurry and pointed in white cement mixed with colour to match the shade of tiles complete all as specified and directed. 51 Material & Labour for non skid ceramic tiles, joint free, coloured tiles7-8 mm thick (Square or rectangular) area of each tile exceeding 0.11 Sqm & not exceeding 0.18 Sqm, as in floors set over and including 15 mm thick cement screed bed or bedding layer in (1:6) CM set and jointed in neat cement slurryand pointed in white cement mixed with colour to match the shade of tiles complete all as specified and directed. 52 Material & Labour for digital glazed ceramic coloure tiles of size 350mm x 450mm x 6-7 mmon vertical surfaces as in skirting/dadoset & jointed in neat cement slurry and pointed in white cement mixed with colour in cement to match the colour of tiles fixed over and including 10 mm thick rendering as backing coat in cement mortar (1:4)completeall as specified and directed. 53 Material & Labour16-18mm thick machine cut Granite stone slab bedded and joined withcementand pointed with white cement with admixture of pigment to match over and including 20 mm thick screed bed in CM (1:6) including cutting and polishing in all outer or exposed surface & rounding the edges of all exposed outer corners as in door cill and jambs / skirting, steps cooking plateformsincludigng wax polishing complete all asspecified and directed. 54 Supply & Fixing 75 mm dia PVC SWR rain water pipe single socketed in any length with rubber ring joints laid in trenches, floorsor fixed in walls with clamps complete all as specified and directed. 55 Supply & Fixing 110 mm dia PVC SWR rain water pipe single socketed in any length with rubber ring joints laid in trenches, floorsor fixed in walls with clamps complete all as specified and directed. 56 Supply & Fixing 75 mm diaPVC SWRbendsany radius joints with adhesive complete all as specified and directed. 57 Supply & Fixing 110 mm diaPVC SWRbendsany radius joints with adhesive complete all as specified and directed. 58 Supply & Fixing 75 mm diaPVC SWR Tee any radius joint with adhesive complete all as specified and directed. 59 Supply & Fixing 110 mm diaPVC SWR Tee any radius joint with adhesive complete all as specified and directed. 60 Supply & Fixing110 mm diaPVC SWR Vent cowl complete all as specified and directed. 61 Supply & Fixing 125/110 mm PVC SWR gully trap, setting and jointing with solvent cement complete all as specified and directed. 62 Supply & FixingVitreous China premium / 1st Quality wash down closet wall hung type EWC with white / Ivory colour in build VC flushing cistern & PVC best quality seat cover complete all as specifeid & directed. 63 Supply & Fixing PVC low level flushing cistern (10 lts capacity) with ball valve float and handle syphonic action type including MS wall mounting brackets and flush pipe of polythelene of low or high density or PVC 32 mm dia complete all as specified and directed. 64 Supply & Fixing table topwhite colour Vitreous China wash hand basinof oval type size not less than 500mm bowl type,32mm CP brass waste coupling,CP brass pillar cock swan neck type 15mm sizehaving long neck and Aerator, CPbrass bottle trap 32 mm size,extension pipes, wall flanges andconcealed GI clamps completeincluding 18mm granite stone of black colour, making necessary holes and other cutting in the counter top and fixing the wash hand basin,pillar cock rigidily including makinggood the walls wherever requiredcomplete all as specified and directed by GE. 65 Supply & Fixing vitreous china urinals, Full stall type white colour with SS grating and union for discharge pipecomplete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long steel fasteners with steel screws, pointing around urinal back in cement complete all as specified and directed. 66 Supply & Fixingshower rose brass chromium plated with or without out swivel joints 100 mm in size fised in steel pipe complete all as specified & directed. 67 Supply & Fixing PVC connection 15mm bore with PTMT nuts and 600 mm long complete all as specified and directed. 68 Supply & Fixingfor15mmconcealedstopcockof chromiumplatedfancytype capstan head handlecopperalloy screwed downhighpressure forironpipeorforunionsfixedcompleteallasspecifiedand directed. 69 Supply & Fixingfor15mmbib cockof chromiumplatedfancytypewith capstan head handle copperalloy screwed downhighpressure forironpipeorforunionsfixedcompleteallasspecifiedand directed. 70 Supply & Fixingfor15mmPillar Tapof chromiumplatedfancytype copperalloy screwed downhighpressure capstan head handle suitalbeforironpipeorforunionsfixedcompleteallasspecifiedand directed. 71 Supply & Fixing for Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm 45gms/40mm-60 gms) complete all as specified anddirected. 72 Supply & Fixing for PVC waste pipe flexible type 32mm bore 700 mm long one socket endcomplete all as specified and directed. 73 Supply & Fixing of angle valve / stop cock with long shank and cup (concealed type) 15mm dia with wall flange, fancy type, chromium plated, screwed down, high pressure, with capstan head handle, screwed both ends for iron pipe / unions complete all as specified and directed. 74 S&F for Heatth Faucet with one meter PVC flexible bodypipe of CPincluding fixing bracket, complete all as specified and directed. 75 S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered white colour 500 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection complete all as specified and directed. 76 S&F of 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in GI pipes complete all as specified and directed. 77 S&F of 25 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in GI pipes complete all as specified and directed. 78 S&F of 20 mm dia of Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iorn pipe and fixed. (minium weight 20 mm-210 gms)complete all as specified & directed. 79 Supply & Fixing PVC floor trap/nahani trap of 75 mm outlet, jointing to waste pipe with rubber adhesive complete all as specified and directed. 80 S&FBrass cromium plate towel rail 20mm dia D type 600m long between flanges complete all as specified and as directed. 81 S&F frameless with LED light ofbeveled edges looking mirror of 5 mm thick selected quality wall mountedfixed to wall with rawal plug and screws complete all as specified and directed. 82 M&L for applying water proofing treatment with the following coats:- (a) First coat of bitumen primer conforming to IS : 3384 @ 0.3 Kg/Sqm (b) Second Layer of APP based polymectric membrane minimum weighing 3 Kg /Sqm and minium 3 mm thick reinforced with polyster non woden fabric (Wt not less than 150 gms/ Sqm) laid on primed surface by torch application with minimum over lapped 100 mm in each directions complete all as specified and directed. 83 M&L for Bitumen primer for use in waterproofing and damp-proofing treatment complete all as specified and directed. 84 M&L 10mm thick rendering or screed bed on top of roof surfaces of any description in cement mortar 1:4mixed with liquid WPC (@ 200ml per bag of 50 Kg) by weight of cement, surface finished even & smooth withoutusing extra cement complete all as specified and directed.Note : WPC shall be measured & paid seperately. 85 Supply only Liquid water proofing compound ISI marked complete all as specified and directed. 86 Supply and laying 20 mm dia of bore CPVC SDR 11 pipes and Plain CPVC SDR 11 fittings (ISI) marked including all necessary required fittings (sockets/bends/Tee) concealed in fixed to wall or laid in floors complete all as specified and directed. 87 Supply and laying 25 mm dia of bore CPVC SDR 11 pipes and Plain CPVC SDR 11 fittings (ISI) marked including all necessary required fittings (sockets/bends/Tee) concealed in fixed to wall or laid in floors complete all as specified and directed. 88 Supply and laying 32 mm dia of bore CPVC SDR 11 pipes and Plain CPVC SDR 11 fittings (ISI) marked including all necessary required fittings (sockets/bends/Tee) concealed in fixed to wall or laid in floors complete all as specified and directed. 89 Supply & fixing seamless ceiling with using 12mm thick factory made gysum fiber board fixed with self tapping screw, including GI frame work for seamless ceiling comprises of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to center intermediate channel 0.90mm thick having two equal flanges of 15 each and web of 15mm each steel expansion fasterners with and including ceiling section (not exceeding 1200mm length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm with clis of 10.5 mm and fixed to the intermediate channel with connecting clis across the intermediate channel at 457mm center to center suitable for suspended system with and including two coat of oil bound distemper (Acrylic) over one coat of cement primer to give even and smooth finish by applying wall care puttey without showing any joints complete all as specified and directed. 90 M & L for two coat of oil bound distemper (Acrylic) over one coat of wall care putty one new plastered surfaces on wall including preparation of surfaces complete all as specified and directed. 91 M & Ltwo coat of cement base paint over one coat of wall care putty on new plastered surfaces on wall including preparation of surfaces on new plastered complete all as specified and directed. 92 M&L for rendering10mm thick fair finished surface using cement mortar (1:4) with WPC on flat roof slab complete all as specified and directed. 93 M&L forpreparingnewplasteredsurfaceofceling andapplyingtwocoatsofoilbound distemper overone coat of cement primer including 2 mm thick wall care putty to make the surface to be plain and smooth complete all as specified and directed. 94 M&L for plain cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in door cills, steps, seismic and other similar bands, plinth courses, lacing courses, parapets and railings, manhold or drain cover, copings, kneelers apex stone, bed plates, kerbs not provided & likeincluding necessary form work, finishing even and smooth without using extra cement complete all as specified and directed. 95 Material & labour for machine pressed (made)precastcement concrete rubber moulded coloured lacker finish inter lockingpaver blocks / tiles60mm thick of grade M-35of any size & shape and desine as approved, with colour pigmentlaid over & including 50 mm thick (average) sand cusionfixedas in floors / paths/ pavings complete all as specified and directed. 96 Supply & Fixing 150mm bore reinforced concrete pipe class NP-2, laid and jointed with cement & spun yarn with collarscomplete all as specified & directed. 97 M&L for 150mm thick PCC 1:3:6 type C-2 using 40 mm graded crushed stone aggregate as in concrete bedding to drain pipes including packing under hauching against the sides of pipes after they are laid and tested for 150 mm bore pipe complete all as specified and directed. 98 Supply & Fixing 20 mm dia (Medium grade) galvanised iron water tubing with all necessary fittings (bends, socket, tee, long peice or reducer) laid in trenches complete all as specified and directed. 99 Supply & Fixing 25 mm dia (Medium grade) galvanised iron water tubing with all necessary fittings (bends, socket, tee, long peice or reducer) laid in trenches complete all as specified and directed. 100 Cutting of existing Cast iron pipes in position for insertion of new tees for making branch connection of 25 mm dia from existing bore of CI pipe with including MS clamps cocomplete all as specified and directed. 101 Supplying, laying, testing and commissioning of XLPE Insulated screened PVC bedded galvanised steel strip wire armured electric power cable(Heavy duty) with aluminium conductor 1100 volts grade cross sectional area of 16 Sqmm 4 Core complete all as specified and directed. 102 Material & Labour point wiring for modular fittings complete with 1.5 Sqmm FRLSH Insulated, unsheathed, multi-stranded 1100 Volts grade copper conductor cable / wires single core conforming to IS: 694 along with two run of 1.5 Sqmm FRLSH insulated copper conductor cable & one run green colour for continuous earthing drawn through and including medium grade rigid PVC conduit conforming to IS: 9537 (Pt-III) and its all necessary accessories / junction boxes / inspection covers of suitable size but not less than 20mm (OD), concealed in wall / floor including provision of modular cover plates with frames of required size and 1.5 Sqmm PVC insulated unsheathed stranded copper conductor (FRLSH) cable for common earth and connecting to earth dolly complete all as specified & directed.Note:- Cutting / chasing in walls & making good shall be include in Quoted rate. 103 One light point / ceiling fan / exhaust fan point controlled by one switch 104 One 6Amp socket point controlled by one switch on same board 105 One 6Amp socket point controlled by one switch on Independent board 106 Ditto all as per srl item No. 102 here-in-before but with 2.5 SqmmFRLSH copper wire with 2.5 Sqmm FRLSH copper earth wire for one 16 Amp socketpoint controlled by one 16 Amp switch on independent board----- ditto --- complete all as specifeid & directed. 107 Supply & fixing Modularswitch1way6Amp1 module 240Volt complete all as specified and directed. 108 Supply & fixing Modular Socket6Amp,2/3 pin combined 2 module 240Volt complete all as specified and directed. 109 Supply & fixing Modularswitch1way16Amp1 module 240Volt complete all as specified and directed. 110 Supply & fixing Modular Socket16Amp,2/3 pin combined 2 module 240Volt complete all as specified and directed. 111 Supply & fixing Modular fan regulator electronic type in 5 steps, 240Voltcomplete all as specified and directed. 112 Supply & Fixing Ceiling rose, three terminals, bakelite body, 240 volts, ISI marked with valid CML complete all as specified and directed. 113 Supply & Fixing Lamp holder angle type with metal ring, PVC/Polycarbonate body modular type with & including 9 Watt LED bulb complete all as specified and directed. 114 M&L for submain wiring alongwith earth wire 2 runs x 4 Sqmm + 1 run x 4 Sqmm with FRLSH Insulated copper conductor, single core cable drawn through and including medium grade rigid PVC conduit ISI Markedconforming to IS: 9537 (Pt-III) and its all accessories/junction boxes/ inspection covers of suitable size but not less than 20mm concealed in wall/ floor complete all as specified & directed.Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length 115 S&F LED Tube light fitting 20 watt batten type 230Volt efficiency 120 Lumens per watt, colour temperature6500k (Cool White), Power factor grater than 0.9, Polycarbonate body, CPRI-80, IP Rating, IP-20, THDV with in 5 % and THDi (8-10%) and integrated Electronic driver complete with all accessories internally Pre-wired and including connecting with 2 Core twisted flexible copper conductor cable of suitable size from celling rose to light fitings complete all as specified and directed. 116 Supply & Fixing ceiling fans complete with blades, down rods, (with remote) and accessories, 230 Volt, 1200 mm sweep Min air delivery 210 CFM with service value more than 6.00 BEE Five star rated with brushless direct current motor (BLDC) complete all as specified and directed. 117 Supply & fixing of exhaust fan with steel body 300mm sweep with bladewith louvers shutter, voltage 230Volt, 50HZ, RPM 1200, Copper winding including connection with 1.5 Sqmm, three core copper conductor wire from ceiling rose to exhaust fan upto 1 RM length including fixing on ventilator completeall as specified and directed. 118 Supply & fixingMCB distribution board, VTPN, 4 way 415 Volt in sheet steel powder painted enclosure double door type withIP-43 degree of protection with built in copper bus bar, neutral link and earth link including MCCB 100 Amp 4 pole breaking capacity 16 KA including cutting of the wall surfaces for flush mounting of DB and making good with cement plaster, finshed with wall care putty and paint to match with the existing surface complete all as specified and directed. Note : MCBs shall be measured and paid separately. 119 Supply & Fixing MCB SP 6-32 Amp, 240 Volt with breaking capacity 10 KA,C series complete all as specified and directed. 120 Material & Labour for fine Sand filling in trenches with clean dry unwashed river sand free from sharp particles or M-Sand, gently punning around the cables for protection complete all as specified and directed. 121 Supplying & laying un-reinforced precast concrete cable coverClass LV, Type-I, flat size 250mm x 150mm x 40mm thick complete all as specified and directed. 122 S&F50 mm dia Light grade galvanised iron water tubing with all fitting laid in trenches or fixed to walls with clamps and in floor for cable protection complete all as specified and directed. 123 S & F security street light fittings better optics for uniform distribution IP-65 protection LED of 35 watt, Heat resistance glass, pressure die cast aluminium housing including 25mm dia galvanised iron pipe light grade bracket bent to required shape over all length 0.6 RM fixed to wall with 02 Nos MS clamps made of 40 x 5 mm FI, 15 cm long, 8 mm dia bolts and nuts with washers grouted in wall complete including requiredlength of 1.5 Sqmm PVC multi-stranded BIS marked 03/02 core copper conductor for electric connection from junction box or ceiling rose to light fittings testing on completion complete all as specified and directed. 124 M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) vertically, with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of MES Schedule Part-I connecting to earthing test. Testing on completion with and including necessary excavation and earth work in any type soil, earth lead connected to earth test point & to main switch board etc with & including adequate quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 (using 20mm graded BT stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, internal surface of concrete shall be given 10mm thick plaster in CM 1:4, pre cast RCC (1:2:4)type B-1 (using 20mm graded BTstone aggregate) 40mm thick cover, reinforced with 8mm dia deformed or TMT bars 3 Nos both way with 12 mm dia round bar handle, GI medium grade watering pipe 20 mm dia with funnel and wire mesh and 15mm dia GI medium grade earth lead protection pipe including provn of earth test point made of 50 x 5 mm MS Flat in D shape 500 mm legth grouted in wall complete 01 x 6 mm multistrand PVC insulated copper conductor ( Green Colour) to be provided from test point to DB through 20 mm dia concealed non metallic conduit complete all as specified and directed.
