Sales : +91-777 804 8217
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 15-12-2025 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 20-12-2025 |
| 2 | 25-10-2025 | Corrigendum_2 | Date | 15-12-2025 |
| 3 | 23-10-2025 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 30-10-2025 |
| 4 | 08-10-2025 | Corrigendum | BOQ | 18-10-2025 |
| Sl. No. | Item Description |
| 1 | Taking down cement or cement plaster, any description on brick or stone walls, etc, including raking out joints, hacking for key, scrubbing down with water, etc.To receive new plaster complete all as specified |
| 2 | M&L for rendering 15 mm thick in CM 1:6 on surfaces or surface other than fair face of brick-work or on one side of lathing of stone masionary or concrete surfaces finished even and smooth without using extra cement, complete all as specified and directed. |
| 3 | M&L for 12 mm thick modified polymer ready mix plaster to concrete surfaceswall finished even and fair with 3 % of weight of cementWPC , complete all as specified and as directed. |
| 4 | M&L for rendering 10mm thick in CM 1:3 on ceiling of concrete surface and finishing the surface even and smooth all as specified and directed. |
| 5 | M&L for preparation of newly plastered surfaces of walls and applying 1 coat of wall care white putty, 1-2mm thick and further applying 2 coats of oil emulsion distemper over a coat of wall priming paint complete all as specified and as directed. |
| 6 | M & L for complete removal of existing treatment on walls and applying 1 coat of wall care putty,2mm thick and further applyingtwo coat of oil bound distemper over one coat of primer paint complete all as specified and directed. |
| 7 | M&L for preparation of new plastered surfaces in walls soffits, facia roof and applying Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade(Company Depot Tinted) with silicon additives@ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. at any height including necessary scaffolding etccompleteall as specified and as directed by Engr-in-Charge of weather coat primer all as specified. |
| 8 | M&L for preparation of new plastered surfaces and applying three coats of white wash on ceiling complete all as specified and directed. |
| 9 | M&L for preparation of old plastered/unplasteredsurfaces and applying two coats of white wash on ceiling complete all as specified and directed. |
| 10 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing of rubbish complete all as specified and directed. |
| 11 | M & L for Glazed ceramic colouredprinted tiles in vertical surface 300x450x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface of tileincluding 15mm thick screed in cm (1:4) as in skirting/dado complete all as specified and directedby Engr-in-Charge |
| 12 | M & L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, (300x300mm) in floors etc. set and jointed in neat cement slurry including 20mm thick screed 1:4 as in flooring complete all as specified and directedby Engr-in-Charge . |
| 13 | M & L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry andincluding 20mm thick screed 1:4 as in flooring complete all as specified and directedby Engr-in-Charge . |
| 14 | M & L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in Skirting /DADO etc. set and jointed in neat cement slurry including 15mm thick screed 1:4 as in flooring complete all as specified and directedby Engr-in-Charge . |
| 15 | Demolition of stone slabs and tiles of any description or thickness laid, bedded and pointed in any mortar . |
| 16 | M&L for 18-20 mm thick Granite (of any type) work(table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. |
| 17 | M & L for Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms, skirting and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following types, including 20mm thick screed bed in CM 1:4, jointed and pointed with grey cement slurryand pointing with white cement (1:3) using marble dust with admixture of pigment to match with shade cutting and polishing etc complete |
| 18 | Demolition of PCC (unreinforced) in ground floors & pavings n exc 15 cm thickness (below or above ground level) |
| 19 | M&L for 75mm thick PCC type C-2, (1:3:6) using 40mm graded stone aggregate for plinth protection with finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed |
| 20 | M&L for Cleaning of existing surface with wire brush removal of all dust & grit of sunken floors, providing 10mm thick rendering in CM 1:4 using WPC at the rate of 3% by wt of cement, one coat of hotblown bitumen VG10 grade @ 1.2 Kg/Sqm on all plastered surface and providing PCC 1:2:4 type B-1 with WPC in slope towards outside, min thickness of PCC is 25mm & max 75mm providing 40mm dia PVC spout of lenth 50cm complete and tested for leakage, seepage and filling with lime concrete or lean concrete 1:5:10 using bricks bat complete all as specified and directed. |
| 21 | Taking down aluminium sliding window /ventilator including glass of size n.exc 1.5 Sqm complete all as specified and directed. |
| 22 | S& F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including thecost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 23 | Taking down wooden chowkats or frames not exc 1.5sqm each with shutters (without taking off shutters from the frame) and disposing off complete all as specified |
| 24 | Taking down wooden chowkats or frames exc 1.5sqm but not exc 4sqm eachwith shutters (without taking off shutters from the frame) and disposing off complete all as specified |
| 25 | Taking down and refixing in same opening after resecuring or easing and adjusting size of shutter exc 01 Sqm but not exc 02 sqm each complete all as specified |
| 26 | S&F Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame, complete as specified by the manufacturer andas per directions of Engineer-in-charge. |
| 27 | S&F to existing door frames 30 mm thickGlass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned woodinside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete as specified by the manufacturer and as per directions of Engineer- in-charge. |
| 28 | S&F 2nd class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed |
| 29 | S&F 2nd class hardwood 35mm thick Glazed & skeleton shutters, open rebated & prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut & mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); to chowkats |
| 30 | S&F 35mm thick 2nd class hardwood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mmB.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed |
| 31 | S&F Aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & fixing bolts & sliding bolts of extruded sections or cast aluminium alloy. |
| 32 | S&F Overall length of cover plate 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete |
| 33 | S&F Mild Steel 300mm, ordinary rat tail rod patttern springs including roller & roller plate complete |
| 34 | S & F of 100 mm long stainless steel butt hinges, medium weightapproved make ISI marked |
| 35 | S & F 100 mm long mild steel butt hinges, medium weight cold rolled complete all as specified and directed. |
| 36 | S & F of 200 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed. |
| 37 | S & F Aluminium handles 150mm long anidised aluminium , cast type,complete allas specified and directed by Engr-in-Charge. |
| 38 | M&L for preparation of new painted wood and wood based surfaces of any description not otherwise described over 10 cm width or girth including knotting and stopping and applying 2 coats of synthetic enamel paint over a prink primer (any tint/Shade) complete all as specified and directed. |
| 39 | Dismantling boarding, any description, fixed in any position with nails complete all as specified |
| 40 | S&F Hasp & staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate with screws 100mm size complete all as specified and directed |
| 41 | S&F for 19/20mm Pre laminated particle board , interior grade , prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to timber framework complete all as specified |
| 42 | S & F Continuous (piano) hinges,Width of flaps (when open) 30 mm mild steel, bright finish or electrogalvanised |
| 43 | Dismantling wrought iron or mild steel work of any description not otherwise described for of any description. |
| 44 | S& F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165complete all as specified |
| 45 | Taking down aluminium decogrill of any size and any type all as specified and directed. |
| 46 | S&F aluminium grill with and including suitable aluminiumanodised frame F/H section as requird manufactured by M/S Decogrill as per design No DG- 103 or equivatent 6.5 mm thick all as specified and as directed |
| 47 | S&F 4.8 mm thick Sheet glass,ordinary quality pin headed type and glazing with Aluminium snap beading with rubber Neoprene packing in squareexc 0.5 sq. m in each pane complete all as specified and as directed |
| 48 | S&F Figured glass 4.0mm thick, pin head type & glazing with oil putty in squares n exc 0.5 sq.m in each pane complete all as specified and as directed |
| 49 | S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire & average width of aperture 1.40mm with aluminium wire staples complete all as specified and as directed |
| 50 | S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with CP bracket guard & railing 60cm long complete all as specified and as directed |
| 51 | S&F in repair 25mm dia Stainless Steel curtain rod etc complete all as specified and directed |
| 52 | S&F in repair statinless steel bracket for curtain rod of 25mm dia for fixing in walls etc complete all as specified and as directed |
| 53 | Demolition and breaking up drain pipes 110/75mm of PVC SWR pipes laid in floor/wall complete all as specified and as directed |
| 54 | S&F of PVC (SWR) pipes 110mm single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed |
| 55 | S&F of PVC (SWR) bends 110mm dia access to door complete all as specified and directed. |
| 56 | S&F110mm bore PVC (SWR) junction single, (Single T) equal or unequal access to door complete all as specified and as directed |
| 57 | S&F 110mm PVC (SWR) vent cowl complete all as specified and as directed |
| 58 | S&F75mm bore PVC SWR pipe single socketed in any length with rubber ring joints laid inin floor/wallcomplete all as specified and directed. |
| 59 | S&F75mm bore PVC (SWR) bends any radius complete all as specified and directed. |
| 60 | S&F75 mm bore PVC (SWR) junction single (Single T) equal or unequal access door complete all as specified and directed. |
| 61 | M&L in 75 mm out let PVC floor trap, plainwith openable (two piece type) grating including jointing with solvent cement complete all as specified and directed. |
| 62 | M&L in 125/110 mm PVC (SWR) gully trap 125/110 mm setting and jointing with solvent cement complete all as specified and directed. |
| 63 | Taking up or down steel tubing of 20 mm bore and connections complete all as specified and directed. |
| 64 | Taking up or down steel tubing of 25 mm bore and connections complete all as specified and directed. |
| 65 | S&F in Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls,ceilings or in floors etc pipes incl cutting/chases of walls etc25mm inclluding fitting (such as elbow teen reducers, couplers short pieces, connection uion etc) whatever required as per manufacturer\"s instruction fixed on wall /ceiling complete all as specified. |
| 66 | S&F Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls,ceilings or in floors etc pipes incl cutting/chases of walls etc20mm including fitting (such as elbow teen reducers, couplers short pieces, connection uion etc) whatever required as per manufacturer\"s instruction fixed on wall /ceiling complete all as specified. |
| 67 | S&F in repair stainless steel plate rack of size 90x75x25cm depth made out of 0.80mm thick sheet complete all as specified. |
| 68 | S&F in repair sink with drainage board made of stain finish1 mm thick kitchen or laboratory with plugs washers including bedding in cement mortar to dwarf wall or including fixing cantilever bracketsoverall size 915mm x460mm bowl size 410mmx330mmx160mm complete all as specified and directed/approved by Engr-in Charge. |
| 69 | S & F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed. |
| 70 | S & F in repairPlastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed. |
| 71 | S & F in repair toilet paper holder, vitreous China,box type complete all as specified and directed. |
| 72 | S&F in repairHealth faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 73 | S&F in repair 10 Litres, PVC valveless,syphonic action type, flushing cistern, low level, white, with inlet, ball vlave, float and handle including bracket complete all as specified and directed. |
| 74 | S&F in repair Vitreous China wash basin, white, flat back, size 550x400 mmexcluding taps, waste coupling and waste pipe.including cutting for and pinning in ends of brackets orrecting stand but exclusive of fixing of supply and waste pipe completeall as specified and as directed |
| 75 | S&F grating square 150 mm size of PTMT openable type complete all as specified and directed. |
| 76 | S&F PVCwaste pipe suitable for wash hand basin/sinkincluding fixing arrangement complete all as specifiedand as directed |
| 77 | S&F 32 mm bore waste coupling of PTMT (half of full thread) complete all as specifiedand as directed |
| 78 | S&F 40 mm bore waste coupling of PTMT (half of full thread) complete all as specifiedand as directed |
| 79 | S&F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specifiedand as directed |
| 80 | S&F in repair 5.5mm thick looking mirror of size 600mm x 450mm, selected quality glass mounted on 6mm thick PVC sheet back surround by 10mmx 10mmx 1.6mm aluminium channel fixed with wooden plugs with chromium plated brass screw and cup washer using rawal plugs, complete all as specifiedand as directed |
| 81 | S&F in repairs Fancy type bib taps, long shank chromium plated cast copper alloy 15mm bore with crutch screwed down and fixed complete all as specified and as directed. |
| 82 | Supply only CP Pillar taps 15 mm dia but fancy type, cast copperalloy , with capstan heads, chromium plated , screwed down high pressure ,with long screwed shanks and fly-nuts , screwed for pvc pipe and fixed. |
| 83 | S&F in repairs 15mm dia stop valves, cast copper alloy, fancy type, chromium plated screwed down, high pressure, with crutch , screwed at both ends for iron pipe or for unions complete all as specified and as directed |
| 84 | S&F in repairs 15mm dia stop valves, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch , screwed at both ends for iron pipe or for unions complete all as specified and as directed |
| 85 | S&F in repair 120mm dia chromium plated overhead showerwith arm complete all as specified and as directed |
| 86 | S & F in repair soap dish, fixed to tiled wall surfaces with plugs and chromium plated brass screws completeall as specified and as directed. |
| 87 | S & FBrass chromium plated tubular towel rod 600mm long completeall as specified and as directed |
| 88 | S&F 20mm thick granite machine cut corner shelf of dia 25cm (inner quarter circle shape) nosing and polishing complete fixed to wall in CM 1:3 mortar completeall as specified and as directed. |
| 89 | Dismantling of water storage tank of exc 250 ltrs& n exc 500 ltrs capacity completeall as specified and as directed |
| 90 | S&F 500 Ltrs Rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I completeall as specified and as directed |
| 91 | S&F 20 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/20 m m - 2 1 0 g m s /25mm-455gms/ 40mm - 690 gms) |
| 92 | Demolition of cement concrete(reinforced) of any description and in any position not otherwise specifically provided for completeall as specified and as directed |
| 93 | M&L for complete removal of loose / cracked concrete incl reinforcement if required, from RCC roof projection,chajja,fins,facia etc and making good withany slab and in anyposition finished the surface even and smooth without using extra cement including necessary form work and welding/binding of reinforcement (including reinforcement)if required complete and match with the existing surface as directed. |
| 94 | M&L for Chipping and removal of spalled concrete, cracked, porous and weak concrete up to a depth of the reinforcement rods or depth of carbonation whichever is deeper and cleaning of the reinforcement bars and exposed concrete to remove scales by chipping, wire brushing, emery sheets etc to enable the measurement of reduced dia of the bar, application of zinc primer to the reinforcementon all sides of the reinforcement and application of epoxy bonding agent to exposed old concrete surfaces. The job shall be carried with contractors own pneumatic chipper / manually with all required resources, tools and tackels up to the satisfaction of EIC. payment towards application of zinc primer and epoxy bonding agent shall be paid in respective item rate of contract. |
| 95 | M&L for providing and placing in position Micro - Concrete as per relevant ASTM / BS / IS having comp. strength of min 45 mpa at 2 days of make PIDILITE/ BASF/SIKA/FOSROC or equivalent in columns and beams, which shall be pre-packed single component, chloride free, non shrink, free flow, self compacting and mixed as per manufacturere spacification, including required leak proof shuttering, pre - soaking of substrate, manual application or pumping, manpower and tools & tackles all complete as per direction of the Engineer - In - Charge. |
| 96 | M&L for repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. meters and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal or rubbish to the dumping ground within 50m lead With cement mortar 1:4 (1Cement:4Coarse Sand) |
| 97 | Taking down / Demolition of old textile covering form roof (old WPT) complete all as specified and directed. |
| 98 | M&L PCC type B-1. 1:2:4 (20 mm graded aggregate) as in Padding concrete to over roof slab 40 mm thick mixed with WPC 3% by weight of cement, finished even and smooth without using extra cement completeall as specified and as directed. (WPC shall be measured and paid separately). |
| 99 | M & L for rendering 10 mm thick rendering in CM (1:4)over PCC padding surface finished even & smooth without using extra cementwith WPC @ 3% by weight of cement complete all as specified and directed (integral WPC will be measured separately) |
| 100 | Supply only integral waterproofing compound complete all as specified and as directed. |
| 101 | M&L for water proofing treatment to RCC roof slab including parapet comprising with the following course of treatment / specification from bottom to top:- (a) Applying bituminous primer @ 0.40 litre per Sqm over plastered surfaces of roof including parapet surfaces. (b) one layer of APP based polymeric membrane of approved manufacturer, 3 mm thick, weight not less than 3.6 Kgs per Sqm, reinforced with non woven polyester fabric or weight not less 150 gms per sqm. Polymeric membrane shall be taken to a height of 60 cm 9 minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing.Note:- (i)Laying of APP based membrane shall be done by torch on method and as per manufacturer\"s instructions.(ii) A minimum overlap of 150 mm and 100 mm should be made in the end and sides of the polymeric membrane respectively and all overlaps and joints are properly sealed as per manufacturer\"s instructions. |
| 102 | S&F PVC door solid frame of size 50mm x 47mm made out of 5 mm thick plain colour PVC sheet reinforced with MSsquaretube complete all as specified. |
| 103 | S&F Factory made solid panel PVC door shutter 30mm thick (stile) consistingof frame made out of MStubes for top and bottom rails MS frameshall be covered with heat moulded plain colour PVC C channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain cover PVC sheets for top rail, lock rail and bottom rail on either side and as gap insertfor top rail and bottom rail, panelling of plain of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles, and rails with suitable PVC sheet beading and joined together with solvent cement supplying l and fixed in the frame at site as per specification and drawing complete all as specified and directed. |
| 104 | S&F mild steel rolled section Fe-410-W(Gde E-250), quality \"A\" as in post, main and cross beams, rafters, purlins connected to common rafters fixed with angle iron clips or other connecting plates complete all as specified and directed. |
| 105 | Dismantling Plain or corrugated steel sheeting, any type / gauge, thickness and any patten of roof coverings, hanger door, hanger roof complete all as specified. |
| 106 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed by Engineer-in-Charge. |
| 107 | M&L PCC type B-0. 1:2:4 (12.5 mm graded aggregate) as in Padding concrete to over roof slab 40 mm thick mixed with WPC 3% by weight of cement, finished even and smooth without using extra cement completeall as specified and as directed. (WPC shall be measured and paid separately). |
| 108 | M&L for providing and laying at or near ground level factory made kerb stone in repairs of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever reqd complete. |
| 109 | M&L for 75mm thick PCC 1:3:6 Type D-2 using 40mm graded stone aggregate as in sub bases all as specified & directed by Engineer-in-charge. |
| 110 | M&L for even spreading of 25mm thick layer of sand cushioning incl watering & consolidation all as specified & directed by Engineer-in-charge. |
| 111 | M&L for machine pressed precast concrete inter locking paver blocks in repairs any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 grade with grey cement and no pigment complete all as specified and directed by Engineer-in-charge. |
| 112 | M&L for preparation of new painted surfaces and applyingtwo coat of synthetic enamel on brick, stone, concrete, asbestos cement or plaster surface all as specifed and directed. |
| 113 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, manholes, etc. or for laying cables/pipes, erecting poles etc. n exc 10 sqm on plan and getting out in soft/ disintegrated rock complete all as specified and directed. |
| 114 | Demolition and breaking up drain pipes 250mm (Salt glazed ware, AC or Reinforced concrete) set in cement mortar in floors including excavation and removal of soil complete all as specified and directed |
| 115 | Demolition and breaking up drain pipes 200mm (Salt glazed ware, AC or Reinforced concrete) set in cement mortar in floors including excavation and removal of soil complete all as specified and directed. |
| 116 | Demolition of brickwork or stone/boulder masonry, built in cement mortar all as specified and as directed by Engr-in-Charge. |
| 117 | M&L for Concrete bed Type D2 1:4:8to 250mm dia drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested |
| 118 | M&L for Concrete bed Type D2 1:4:8to 200mm dia drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed. |
| 119 | M&L for 250mm bore reinforced concrete pipe class NP2 laid and jointed complete with collars all as specified and directed. |
| 120 | M&L for 200mm bore reinforced concrete pipe class NP2 laid and jointed complete with collars all as specified and directed. |
| 121 | M&L for pre-cast reinforced cement concrete1:2:4, type B1 (using 20mm graded stone aggregate) as in manhole coverwith plain fair surface including chamfers, weatherings, throatings, necessary form work and set in CM (1:6), placed in position complete all as specified and directed. |
| 122 | M & L Mild steel CRS TMT bars 8 mm dia , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips |
| 123 | Cutting into existing manholes of 150mm internal dia of pipes for connecting new drains, making good to pipe and rendering cutting out existing benchingand forming branch channel in PCC (1:2:4) type B-1, smooth finished complete all as specified and directed. |
| 124 | M&L for walling of Porbandar stone masonry well bonded and solidly hearted built in CM 1:6 complete all as specified. |
| 125 | M & L Rendering15 mm thickin CM (1:4)on stone/concrete surfacefinished even & smooth with using extra cement incl using integral WPC etccomplete (integral WPC will be measured separately. |
| 126 | M & L cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in foundation filling and mass concretecomplete all as specified. |
| 127 | M&L for providing cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in copings, benching,and the like including weathering, sightly rounded or chamfered angles and throating as directed. |
| 128 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in hard/dense soil |
| 129 | Returning and filling in trenchesincl spreading, levelling watering andraming in layer n.exc 25 cm as in soft/disintegrated rock complete all as specified and directed. |
| 130 | Removing excavated material (soft/disintegrated rock) exc. 1.50 km but n exc. 5 km and depositingoutside MoD land complete all as specified and directed. |
| 131 | Removing of excavated mtrls (soft/disintegrated rock) n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point. |
| 132 | Making connection of CPVC pipe distribution branch with GImain of 80/100mm dia size by providing and fixing tee including cutting and making fusion joint etc. |
| 133 | Supply Repair/Replacement Laying and Testing of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fittings and making connection fixed complete to walls, ceilings floors or laid in trenches etc. of 32 mm dia laid in trenches complete all as specified and directed. |
| 134 | All as per above item No 133.00but for 25 mm dia. |
| 135 | All as per above item No 133.00but for 20 mm dia. |
| 136 | Supply and Repair/Replacement ofCPVC ball valve valve 32 mm borecomplete all as specified and directed. |
| 137 | Supply and Repair/Replacement ofCPVC ball valve valve 25 mm borecomplete all as specified and directed. |
| 138 | Supply and lay Double Walled Corrugated (DWC) Pipes having corrugation on the outer wall and plain surface on the inner wall confirming to IS14930 (Part-II) for protection of UG cables size 50 mm outer dia laid in trenches/ road/ drain or fixed along wall, poles or laid under floor all as spd and as directed by Engr-In-Charge. |
| 139 | Supply and lay Double Walled Corrugated (DWC) Pipes having corrugation on the outer wall and plain surface on the inner wall confirming to IS14930 (Part-II) for protection of UG cables size 40 mm outer dia laid in trenches/ road/ drain or fixed along wall, poles or laid under floor all as spd and as directed by Engr-In-Charge. |
| 140 | Supply & Fixing in replacement of installation, testing and commissioning factory made, floor mounted outdoor type LT panel board, cubicle type, suitable for 415 Volts, 3 Phase, 4 wire, 50 Hz, AC supply system, CPRI approved manufactures having bus bar chamber with insulated Aluminium bus bar 600Amp rated, four wire system, colour coded for each phase of rating as per under for phase and neutral, insulated on epoxy type insulators. The panel shall be dust and vermin proof, IP-54 class protection and made 3.15 mm of outer body and inner body 2.00 mm thickCRCA MS sheet , powder coated finish over one coat of red oxide primer on outside surface and painted inside with two coats of red oxide primer, both side opening type, including internal wiring with PVC insulated solid copper conductor cable, IS-694 marked, 1100 volts grade of appropriate size (but not less than 2.5 sqmm)including grouting of panel 30 cm above ground level by providing 60 cm long angle iron frame of size 40x40x5mm, welded on all the four corners, embedded in pcc 1:2:4 using 20 mm stone aggregate upto 30 cm complete all as specified and directed including the following accessories:- (Make:-CPRI Approved) |
| 141 | (a) MCCB Thermal magnetic based400 Amps, 4 pole,36 KA, 415 V -01 No (Incoming)(b) MCCB Thermal magnetic based 200Amps 4 pole ,25 KA, 415V (Ougoing)- 01 No(c) MCCB Thermal magnetic based 125 Amps 4 pole ,25 KA, 415V (Outgoing) - 1 No(d)MCCB Thermal magnetic based 63 Amps, 25 KA, FP, 415V- 08 Nos (Outgoing) (e)MCB 32 Amps, 10 KA, SPN - 2 Nos (O/G) (Spare-01No)(f)Digital Ammeter with CT\"s and Selector switch-01 Set(g)Digital Voltmeter with selector switches-01 No(h)Digital Multifuntional Meter with selector switches - 01 No(j) Indicating lamp LED Type-RYB Set of Three -01 Set |
| 142 | Supply, laying and testing in Replacement ofXLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 3.5 core complete all as specified and as directed. |
| 143 | Supply, laying and testing in Replacement ofXLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4 core complete all as specified and as directed. |
| 144 | Taking down carefully aluminum/copper point wiring (light,fans,socket etc) complete incl battens and fittings such as switch, ceiling rose,light fittings, regulaters, socket etc and making good disturbed surface of wall/floor etc complete all as specified. |
| 145 | M&L for point wring for one light/ fan controlled by one switch with 1.5 sqmm nominal area) PVC insulated and PVC unsheathed multi stranded copper conductor cable FRLSH in and including concealed PVC conduit 20 mm dia medium duty ISI marked, including suitable new steel sunken boxes, modular frame and cover plate for fixing of modular switches as per required point in that board, flush to surface for one light point, fan point, controlled by one switch on the same board with other switch or independent including PVC insulated unsheathed 1.5 sqmm copper conductor cable FRLSH connected to common earth duly complete including cutting, chasing the surface and then making good the same in CM 1:6 complete all as specified and directed. Notes : 1. Switches, Sockets etc shall be measured and paid for separately under appropriate items of Sch \"A\".2. PVC Casing caping wiring shall be provided where concealed wiring is not feasible (i.e. concrete surface/ beam/ column/ ceiling etc.) The same shall be deemed to included in the quoted rate. No extra cost shall be paid for the PVC casing caping item. |
| 146 | All as per item No.144 above but for one light point for 2way switch board. |
| 147 | All as per item No.144 above but for one 5 amps socket outlet on same board. |
| 148 | All as per item No.144 above but for One 3 pin socket outlet, 5 Amps, independent board complete all as specified andas directed. |
| 149 | All as per item No.144 above but for One bell/ buzzer point controlled by one push button on the same board with other switches or independent with cables 1.5 sq.mm sizecomplete all as specified andas directed. |
| 150 | All as per item No.144 above but for One 3 pin socket outlet with 2.5 sqmm cable for 15 amps switch socket combination outlet on independent board complete all as specified and directed. |
| 151 | All as per item No.144 above but for one AC Pointwith 4 sq mm PVC unseathed (FRLSH) wire along with 4 sq mm green colour wire as earth contuinity conductor connected to common earth dolly complete all as specified & as directed by engr-in-charge.Note : Seprate circuit of individual point will be drawn from the DB directly for AC Point complete all as specified and as directed. |
| 152 | M&L in replacement for Sub main wiring power/circuit using PVC insulated unsheathed FRLSH, stranded copper conductor cable 2 Single core of size 6 Sqmm, earth continuity conductor of size 6 Sqmm to be drawn through in and including PVC conduit concealed in walls/roof/floorsall as directed by Engineer in Charge.Notes:- (i)Two wires of 6 sqmm and one wire of 6 sqmm & PVC conduitshall be measured as one unit.(ii) Each Submain wiring in separate PVC conduit.(iii) PVC Casing caping wiring shall be provided where concealed wiring is not feasible (i.e. concrete surface/ beam/ column/ ceiling etc.) The same shall be deemed to included in the quoted rate. No extra cost shall be paid for the PVC casing caping item. |
| 153 | M&L in replacement for Sub main wiring power/circuit using PVC insulated unsheathed FRLSH, stranded copper conductor cable 2 Single core of size 4 Sqmm, earth continuity conductor of size 4 Sqmm to be drawn through in and including PVC conduit concealed in walls/roof/floorsall as directed by Engineer in Charge.Notes:- (i)Two wires of 4 sqmm and one wire of 4 sqmm & PVC conduitshall be measured as one unit.(ii) Each Submain wiring in separate PVC conduit.(iii) PVC Casing caping wiring shall be provided where concealed wiring is not feasible (i.e. concrete surface/ beam/ column/ ceiling etc.) The same shall be deemed to included in the quoted rate. No extra cost shall be paid for the PVC casing caping item. |
| 154 | Supply and Repair/Replacement of ceiling rose surface backelite 65x50 mm having3 terminal complete all as specified and directed.. |
| 155 | M&L for SPN Sheet metal enclosures with plug and socket with Top and MCB SP 20 Amps including taking down the same. all as specified and directed by Engineer - in - Charge. |
| 156 | M&L for taking down and refixing for after Painting of ceiling fanscomplete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc complete all as specified and as directed. |
| 157 | M&L for taking down and refixing for after Painting of Exhaust fancomplete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc complete all as specified and as directed. |
| 158 | M&L for taking down and refixing for after Painting of Geysercomplete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc complete all as specified and as directed. |
| 159 | Repair/replacement of Flexi connection pipe accessory 450mm for water heater any type/capacity complete all as specified and directed |
| 160 | M&L For breaking the existing wall to make hole for exhaust fan and making good to the disturbed surface of wall complete all as specified and directed at site. |
| 161 | Supply and fixing exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m complete all as spcified and as directed |
| 162 | Supply and fixing in Repair/Replacement LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete complete all as specified and as directed |
| 163 | Supply and fixing in Repair/Replacement LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed |
| 164 | Supply and fixing in Repair/Replacement of Decorative wall light made up of high grade engineering plastic material suitable for retrofit CFL 20 W . with all connected accessories internally pre-wired, including 9 W LED bulb connecting lead of 3 core 1.5sqmm flexible copper wire 1.5sqmm from ceiling rose to fitting complete all as specified and as directedMake:- Havells Cat Part No. LHFOGBE1TZ1W035 or equivalent in Wipro/ Bajaj/Crompton. |
| 165 | Supply and fix in Repair/Replacement of Building street light fitting Endura pearl 20W LED lamp new genaration energy saving & environmental friendly long life made up of pressure die-cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP opening separate driver compartment with IP65 protection and impect resistance of IK07,with suitable ofGI pipe (light grade) bracket and clamps,nut bolts are fixed on wall/post and all as required and directed.Make:- Bajajcat no EBCLST20WLEDIV2 or equivalent in Wipro/ Havells/ Crompton. |
| 166 | S&F in Repair/Replacement of Modular switch 1 way 6 Amps, 1 modules 230 volts complete all as specified and directed. |
| 167 | S&F in Repair/Replacement of Modular switch 2 way 6 Amps, 1 modules 230 volts complete all as specified and directed. |
| 168 | S&F in Repair/Replacement of Modular switch 1 way 16 Amps, 1 modules 230 volts Complete all as specified and directed. |
| 169 | S&F in Repair/Replacement ofModular socket 6A,2/3 pin combined, 2 modules 230 volts complete all as specified and directed. |
| 170 | S&F in Repair/Replacement ofModular socket 6A/16A,2/3 pin combined, 2 modules 230 volts complee all as specified and directed. |
| 171 | S&F in Repair/Replacement ofbell push 6 Amps, 1 modules 230 volts complete all as specified and directed. |
| 172 | S&F in Repair/Replacement of call bell Multi musical type complete all as specified and as directed |
| 173 | S&F in Repair/Replacement offive step fan Modular regulator 2 module 230 volts complete all as specified and directed. |
| 174 | S&F in Repair/Replacement ofMCB DB Single pole and neutral 12 way 240V double door Complete all as specified and as directed. |
| 175 | S&F in Repair/Replacement ofMCB TPN DB 4 way 415V double door Complete all as specified and as directed. |
| 176 | S&F in Repair/Replacement 240V, 10 KA \"C\" curve miniature circuit breaker (MCB) of single poles and current carrying capacity SP 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed by Engineer - in - Charge. |
| 177 | S&F in Repair/Replacement Supply and fixing SPN 40 amps rating 240V, 10KA \"C\" curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed by Engineer - in - Charge. |
| 178 | S&F in Repair/Replacement Supply and fixing SPN 63 amp rating 240V, 10KA \"C\" curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed by Engineer - in - Charge. |
| 179 | S&F in Repair/Replacement of 63 amp TPN 415V 10KA \"C\" curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and directed by Engineer - in - Charge. |
| 180 | M&L for Repair/Replacement of fabrication of Wooden Box as suitable for SPN 4 way to 12 way DB to be covered as per existing including suitable mason work,surface finishing as per original and locking system complete all all as specified and as directed. |
| 181 | M&L for Repair/Replacement of fabrication of Wooden Box as suitable for TPN DB to be covered as per existing including suitable mason work,surface finishing as per original and locking system complete all all as specified and as directed. |
| 182 | M&L in Replacement of earthing complete with galvanized steel earth plate electrode of size 600 x 600 x 6 mm thick buried directly in ground to a depth not less than 2.25 mtr below the normal ground level with top edge of earth plate not less than 1.50 mtr below the normal ground level and connected to galvanised earth lead wire 4.0mm dia by means of nut, bolt & washer and protected by 40mm dia GI pipe light grade and watering pipe of 20mm dia GI pipes light grade and connected to earth test point including necessary excavation, earth work, PCC chamber (1:3:6) type C-1 and 40 mm thick RCC pit cover in RCC (1:2:4) type B-1 using 6 mm dia MS round bars @ 150 mm C/C both waysall as shown in electrical plate No. 3 of SSRPart-I all as specified and directed. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
