Tender For Renovation Of Proteomics Facility At Ks-19,Gf,Cri, Actrec.; 1 Civil Works 2 ALUMINUM SLIDING WINDOWS/DOORS: Providing & fixing in position aluminum openable window shutter with frame fully glazed / aluminum grills with using 5.5mm thick glass sheet of approved make and quality plain/frosted / bajari glass fixed with aluminium beeding channels with two way rubber gasket / PVC lining to ensure water tightness. Nos rattling for aluminium grill fixing with F Channel beeding using satin finish anodized 15 micron Jindal sections for shutters and frame of required size and section including using aluminium / S.S. hinges of required size , tower bolt of necessary size , C type alum handle for shutterand other essential hardware as per requirement etc. complete all as per specified and directed by Engineer in charge. Alumn. Sliding window with powder coated/anodized 3 ALUMINUM PARTITION WITH DOOR WORKProviding & fixing alumimium partition to the required height partly glazed and partly panneled or fully glazed or fully panneled using aluminium section satin finish anodizing of required size for bottom, top, middle & vertical rails at required intervals panneling with 12mm thick both side pre-laminatdboard fixed with sloping aluminium beeding alround with neoprine gasket glazing with 5.5mm forsted/ bajri/ plain glass fixed with alumimium channel beeding two way PVC lining/ rubber gasket to ensure water tightness and Nos rattaling including providinG necessary cover mould using suitable alumimium section so as to take care of gaps between the walls/ ceiling /flooring and partitions etc. including providing and fixing necessary fittings as specified and directed.Partly glazed partly panneled. 4 VETRIFIED DADO/ FLOOR TILES Providing & laying polished vitrified floor tiles in different sizes (thickness to be specified by manufacturer) with water resistant less than 0.08% and confirming to IS 15622 of approved make in all colors & shades, laid on 20mm thick cement mortar 1:3 ( 1 cement : 3 coarse sand) including grouting the joints with white cement and matching pigments etc. complete: Size of tile 60x60 cm (2 x 2) (joint free) including hacking/scraping exeats plastered surface. 5 INTERIOR FINISHING: Providing & Applying one / two coats of primer & thereafter two coats of paint as mentioned below of approved make First quality to the required colour scheme and as per manufacturers instructions/specifications to the walls, beams, columns, ceilings, partitions doors etc. including thoroughly scrapping the existing surface with sand papers, removing old paint, filling up crevices and Applying and Levelling the existing surface withWhite Cement based/ Coloured waterproof Putti/POP Coat of average thickness of 1 mm or 2 mm as per requirements of approved brands necessary to obtain smooth surface, filling of cracks, removal of stains, painting spots on floors, aluminum window frame & glass etc. including scaffolding etc. as to the entire satisfaction of engineer in charge. Using Luster Paint 6 Providing & applying 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix : 1:4, including curing, scaffolding etc. complete as directed and instructed. 7 GRANITE: Providing and fixing 18mm thick gang saw cut mirror polished remolded and prepolished) machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels 8 Providing & laying poly vinyl chloride (PVC) rolls flooring of min 2mmthick of medical grade manufactured of approved make and approved pattern for flooring, skirting/dado laid onexisting cement tile or concrete of plastered floor finish with suitable adhesive as per manufacturers specifications close jointed and finished to proper bends, slopes and plumbs, sealing joints with matching colour wielding rods applying Epoxy chemical for to fill undulation in flooring,as directed etc. complete generally as per manufacturer’s specifications. 9 Providing and fixing sun control films 1.5 mm thickfilm on window glasses without damaging rubber gaskets, handle , friction hinged etc. complete including necessary scaffolding job is to be completed as per garware film specification and as directed by EIC 10 REMOVING ALUM PARTION WORK Removing old aluminum partition with all fittings transporting to the required place in T.M.C. premises & refixing the same after making the required modificationadding the required aluminum sections at the new site of work including materials Labour etc. complete as directed by engineer in charge. 11 Providing & fixing Roller blinds (Premium quality) of approved make with heavy duty roller brackets & necessary fixtures. 12 WOODEN CABINET Providing & fixing cabinet made up of 19 mm. Commercialply of approved make for top, bottom, sides & shelves & 8mm commercialply approved make for back side Door shutter made up of 19mm thickcommercial ply and outer surfaces and top of shelves for open type cabinetshould be laminated with 1.5mm thick approved plastic laminate sheet of required colour including all brass fittings such as hinges, tower bolts, ballcatches, stopper, handle, knobs as per shown in drawing or approved byEngineer-In-Charge etc. And all exposed edges lipping with 6mm Thick T.W. lipping Patti. Locking arrangement with multipurpose lock etc. allcomplete as specified & directed by Engineer-In-Charge. With shutter 13 COMPUTETR TABLE Providing making & supplying computer table made out of 19mm commercial ply for table top, mounted on the vertical side of 18mm commercial ply and cabinet made out of 19mm commercial ply for sides, shelves & shutters making concealed monitor arrangement by providing 8mm thick clear r glass on table top of required size with edge polish asshown in drawing drawer and ready made key board drawer with heavy sliding channels with powder coated handle for shutter, cable managerdrawers all edges shall be lipped with 6mm thick T.W. lipping Patti. All exposed faces should be 1.5mm the laminate of approved colour and non laminated area should be French polished include. cost of other materials labor etc. as per drawing and as specified and directed by Engineer-In Charge. Computer Table with all inner surface with 1mm the approved laminate. 14 GRANITE: Providing and fixing 18mm thick gang saw cut mirror polished remolded and prepolished) machine cut for to be placed over wooden cabinets, table top with epoxy adhesive complete as directed and instructed. 15 MODULAR LAB TABLE WITH REAGENT SHELVES Design, fabrication, supply & installation of factory finished Lab working table with granite top of 1500 x600/750/900 mm wide and table height from 750/900 mm with edge shamphered placed on 12mm thick marine ply fixed firmly over dual colour powder coated metal frame, with movable drawer unit to fit underneath of matching dual tone coulr combination and with dedicated power point have electrical power points of 6 Module (2nos of 15/5 A plug with switch x 2 board on each table length of min 1500 mm) supply running shelf connected to main lab table frame matching colour scheme with matching metal cabinet underneath with drawer/ shutter handles and lock & key arrangement.The pic enclosed is for repetitive purpose only.The agency shall submit the sample for approval before supplying in bulk, complete as directed and instructed. :-Lab table 750mm width and 900 mm high 16 Removing the existing PVC flooring along with handing over serviceable material and disposal of waste as per instruction of Engineer in charge. 17 PLASTER BREAKING: Labour charges only for removing existing metal/ damaged / cracked / loosened cement / neeru /rough casts and faced plaster or tile work with back coat at all floors and levels including leaning the surfaces clear of all loose concrete/mortar foreign materials, carting away the debris out of hospital premises including scaffolding raking concrete surfaces etc. complete with quantities to be executed as and when required and as directed by the Engineer- In-Charge. 18 Electrical Works 19 SITC of Primary point wiring for light point/ fan point/ exhaust fan point/ call bell point with 2 x 1.5sqmm + 1 x 1.5sqmm FRLS PVC insulated copper conductor single core cable in surface / recessed includingmedium class PVC conduit Heavy(HMS) / casing capping , with modular switch , modular plate,suitable GI box for concealled , suitable PVC box for surface, ceiling fan rose, PVC junction box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. (Average circuit lenght 20 mtr) 20 SITCSecondary point wiring light to light looping with 2 x 1.5sqmm + 1 x 1.5sqmm FRLS PVC insulated copper conductor single core cable in surface / recessed includingmedium class PVC conduit Heavy(HMS) / casing capping , with modular switch, modular plate,suitable GI box for concealled , suitable PVC box for surface, ceiling fan rose, PVC junction box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. ( Average circuit length 10 Mtr ) 21 SITC of Wiring for circuit/sub main using 2.5 sqmm, PVC insulated, FRLS, stranded, flexible copper conductor wires. 22 SITC of Wiring for circuit/sub main using 4 sqmm, PVC insulated, FRLS, stranded, flexible copper conductor wires. 23 LED Down lighter (SMD Type) (System lumen efficacy ≥ 105 < 120 lm/Watt ) 18wattSupplying, installation, Testing & Commissioning of LED Recessed/ surface Down lighter (Round/ square/ Rectangular) SMD type of following bodymaterial with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%,Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI>80 , UGR (Unified Glare Rating) < 19, Flicker free (flicker should be below5%), life time (LED,Driver & electrical circuitary), of minimum 50000Burning Hours with 70% of initial Lumen maintained till life ends ,CCT 3000°K / 4000°K / 5700°K / 6000°K / 6500°K (As per ANSI Bin),SDCM (Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be confirming to relevant BIS standards and trade mark certificate (T.C.).Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c connections with 1.5 sq mm FRLS,PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 and <120 lm/Watt output . LM79 & LM80 Test report from NABL lab for alltesting required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement.(Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C) 24 Supplying and fixing the following size/ modules, PVC boxfor modular switches in surface / concealed, etc. as required. Including finishing of the same for concealed fixing with cement, and final painting as per actual. 25 1 or 2 Module 26 6 Module 27 12 Module 28 Supplying and fixing the following size/ modules, modular base & cover plate for modular switches in surface / concealed, etc. as required. Including finishing of the same for concealed fixing with cement, and final painting as per actual. 29 1 or 2 Module 30 6 Module 31 12 Module 32 Supply and fix the following modular switch/ socket on the existing modular plate & switch box, including connections but excluding modular plate, etc., as required. 33 Modular switch 6A/16A 34 Modular Socket 6A/16A 35 Modular ceiling fan regulator (2 module) 36 2 Pin + Earth, reroll type 20 Amps metallic sockets- 1 NO / 20 Amps MDS make SP MCB with separate Neutral link as controlling S/W - 1 No./20 Amps metallic top 1 No for the above socket. 37 Supply, Installation, Testing and Commissioning of1200mm ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal( Aluminum alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, suitable for operation with regulator for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C(max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Ceiling Fan compliant to IS 374:2019 fan Supply, earthing etc. complete as req 38 SITC of Cat 6 type I/O with RJ 45/11 socket with Box, faceplate and fixing screws, having the compliance/certifications for ISO 9001:2015 & ROHS 39 Supply & laying of CAT-6 cable through provided casing-capping, PVC conduit, all as directed by EIC. 40 Supply & Fixing of 25 mm size PVC rigid conduit with spacers & saddles screws, rawal plug etc. along with all accessories complete in all respect on any hard surface/wall/trench/ceiling etc. Compete as per instruction of EIC. 41 Supply & Fixing of1.25 inch casing cappingwith spacers & saddles screws, rawal plug etc. along with all accessories complete in all respect on any hard surface/wall/trench/ceiling etc. Compete as per instruction of EIC. 42 Dismantling/removing the existing light, fan, bell, independent plug point, wiring of all types with accessories, Switch boards, etc. 43 Dismantling the existing mains wires of all sizes, make running through PVC casing capping/pipes/MS conduits including casing capping/PVC pipes/ MS pipes/GI pipes/ HGDWC pipes/PVC or Metal trunking etc. 44 HVAC Works 45 FCU 46 Supply, Installation, Testing and Commissioning of chilled water Fan Coil Unit. The Fan Coil Unit shall be a factory-assembled, tested, and ready-to-install unit suitable for wall mounting at high level. Units shall comply with relavantstandards for performance and safety. Cooling Coil: Multi-row copper tubes with hydrophilic aluminum fins, high-efficiency, seamless construction. Casing: High quality, powder-coated galvanized steel or ABS plastic body with corrosion protection. Drain pan: ABS/stainless steel with 7mm PE insulation to prevent condensation. Fan type: Dynamically balanced centrifugal or tangential fan, low-noise design.Motor: Single-phase, multi-speed motor with internal thermal overload protection. Coil shall be designed for standard working press of 1.6 MPa(16bar) and the test pressure is 3.3MPa(33bar). Filters: Type: Washable synthetic fiber or nylon mesh filter. Thermostat: Microprocessor-based wireless remote controller with LCD display; mode selection (cool/fan/dry/auto), fan speed, temperature setting. Accessories : Pre-assembled valve station includingMotorized 2-way/3-way valve with actuator. Strainer, ball valve with tray. Copper pipe line with factory fitted GC cloth insulation require from the main header also to be considered. no additional cost given for the same. It shall also have RS485 Modbus communication function for BMS control .Supply & laying of control wiring & power cabling from FCU to local control panel / thermostat and motorized valve actuator, with conduits and accessories. Hole in wall/ dry portion required shall be included. 47 Decorative Hiwall- 2 TR ( 800 cfm) 48 Removing,Refitting, Gas charging & Commissioning of Existing split AC of 2.0 ton as per instruction by EIC. 49 SITC Copper pipe with Insulation sleeve ( covered with white monsoon tap) 1/4, 1/2 or as per OEM standard for 2 TR capacity split AC. Pipe shall be measured in pair. 50 Supply, Laying, Termination of flexible power/control cable4C x2.5 sqmm or as per standard size 51 SITC of PVC drain pipe with 6mm nitrile insulatios as per below size 52 25 mm 53 32mm 54 SITC of PVC casing caping for laying of copper pipe & cable 3 to 5 or as per required size
