Tender For Special Repair To Bldg No P 63 F And Provn Of Two Toilets At Alhilal Mil Stn; 1 Taking down chowkats or frames incl shutters (without taking off shutters from the frames) n.exc. 1.50 sqm each, and removing from site, complete all as specified and directed. 2 Taking down chowkats or frames incl shutters (w/o taking off shutters from the frames) exc. 1.50 sqm but n.exc. 4 sqm each and removing from site, complete all as spfd and directed. 3 S & FPressed steel frames of size 125 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc and providing one shop coat of primer andtaring back side of frame, complete all as specified and directed. 4 S & F (Fe-410W(GdeE-250) qualityB) Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing completecomplete all as specified and as directed. 5 S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) 6 S&FProviding and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) . 7 S&F 35 mm thick, single piece factory made wire gauge door shutter and incl of wire cloth (stainless steel & aluminium XPM) manufacturing by PVC sheets printed 5mm thick on both side on frame made out of M.S tube 19 SWG, size 19x19 mm complete in all respect with lock rail & beautified by PVC beading all around fixed with PVC solvent cement complete as per Drg No.CEPZ/TD-378/Sheet 1/1 dated 27/12/2011 complete all as specified and directed. 8 M&L Plain cement concrete 1:2:4 (Nominal mix), type B-0 (Using 12.5mm graded stone aggregates) as in filling of steel chowkats or frames, cills and hold fast etc.complete all as specified and as directed. 9 S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples , complete all as specified and directed. 10 S&F box type steel windows comprised of tubular frame and shutters made out of 1.25 mm thick MS tube factory made with double side shutters wire gauged shutters & glass glazed shutter(wire and glass panes shall be measured and paid separately) with side hung shutters with steel handles and steel peg stay doytailed at welded incl 2 Nos tower bolts 150 mm long for each leaf and 8 mm square bar grills at spacing as shown on drg welded to FI frame work,incl other fittings,hinges,handles tarred hold fast PCC blocks etc. all as shown on drg No CEPZ/TD-354/09 sheet 1/3 to 3/3 ,complete all as specified. 11 M&L Preparing new steel surface of steel of any description, over 10 cm width or girth not otherwise described and applying two coats of synthetic enmel paint over a coat of red oxide, zinc chrome primer complete all as specified and as directed. 12 S&F 3 mm thickSheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane , complete all as spfd and directed 13 Hackingoutoldbrokenglass (any thickness, size, quality or description)from metal frame including punching or drilling out old glazing pins/springclips 14 Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in any type of soil. 15 S&FFramed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framedbalusters; walk ways; railings; framework of water tanksand similar work conforming to Fe.290.Gde-E-165. Complete all as spd and as directed. 16 S&FAluminium anodised, barrel tower bolts 100mm long of extruded section and fixed, complete all as specified and directed. 17 S&F Aluminium anodised barrel tower bolt of extruded section, 150mm long complete all as specified and directed. 18 S&F 150mm long aluminium handle, cast type, anodised complete all as specified and directed. 19 S&FAluminium alloy, 300mm anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed 20 S&F in repairs 300mm long MS ordinary door springs including roller and roller plate complete all as specified and directed. 21 Demolition/Dismantling floor, hearth wall tiling inclding cement mortar bedding (but not backing) removing servicable tiles to store & rubbish off the premises.Note :- All Demolition debris Romove from site and disposed out of Military area. 22 M&L for Glazed ceramic tiles coloured in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or Lolour cement to match 7mm as in skirting / dado etc laid over and including 10 mm thick backing coat in cement mortar 1:4, set and jointed in neat cement slurry and pointed with coloured cement to match the tiles complete 23 M&L forjoint free (edge cut) Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of eachtile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, laid over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed with coloured cement to match the tiles complete. 24 M&L for Non skid/Matt finish/Sugar finish of joint free (edge cut) Ceramic tiles 7 to 8 mm thick area of eachtile exceeding 0.18 sqm but not exceeding 0.38 sqm, as in floors etc laid over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed with coloured cement to match the tiles complete. 25 M&L Machine cut kota stone flooring 18 to 20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and polishing incl screeding bed 15mm thick in CM 1:4 compete all as spcd. 26 M&L for cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) 25mm thickas in leveling course offlooring & roof complete all as specified and directed. 27 M&L 18 to 20mm thick Granite (of any type) workKitchen slabs , window cill etc. (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. 28 Dmolition of stone/brick/concrete blockmasonry built in Cement mortar complete all as specified.Note :- All Demolition debris Romove from site and disposed out of Military area. 29 M & L brick work with sub class -B bricks, straight or curved on plan exc 6mtr mean radius built in CM 1:6. 30 Walling random rubble stone masonry, uncourced, well bonded, bedded and solidly hearted, build in cement mortor 1:6 complete all as specified and directed. 31 Demolition of cement concrete (Unreinforced) in ground floor and pavings n exc 15cm thick ness (below or above ground level)Note :- All Demolition debris Romove from site and disposed out of Military area. 32 M & L Plain cement concrete, M-10 (Nominal Mix) type C-1 (using 20 mm graded crushed stone aggregates) as in surface channels or drains etc,complete all as specified and directed. 33 M&L extra forming fain finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds mitred/stopped end etc 34 Add or deduct for each 25 mm girth or part thereof over or under 30 cm ditto. 35 PCC M- 15 (Nominal mix) as in coping including necessary form work and finishing complete all as specified and as directed. 36 M&L 50mm thick, PCC M-10 (Nominal Mix), type C-2 (using 40mm graded crushed stone aggregates) as in plinth protection finished even and smooth without using extra cement, complete all as specified and directed. 37 M&L PCC 1:3:6: type C-2 (using 40 mm graded stone aggregate) mass concrete. Complete all as specified. 38 Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided, complete all as specified and directed.Note :- All Demolition debris Romove from site and disposed out of Military area. 39 M&L RCC M-15 (Nominal mix), type B-1 (using 20mm stone aggre) as in slab supported on walls, beams and columns in floors, roofs, landing, balconies, canopies, deck slabs and in shelves and the like, complete all as spfd and directed. Note -Reinforcement if used shall be measured and paid separately under relevant item. 40 M&L Form work to sides and soffits of suspended slab, such as roof slab, floor slab, landing and similar work n.exc. 200mm thick (horizontal or sloping) for fair finished surfaces, complete all as specified and directed. 41 M&L TMT bars 10mm dia and over, cut to length, bent to shape reqd, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9mm dia, complete all as spfd and directed. 42 M&L TMT bar 6 to 8mm dia and over, cut to length, bent to shape reqd, incl cranking, bending spirally for hooping for column, hooking end and binding with and incl mild steel wire (annealed) not less than 0.9mm dia, complete all as spfd and directed. 43 Taking down cement plaster incl tiles of any description on brick or stone or cement concrete walls incl raking out joints, hacking for key, scrubbing down with water etc, complete all as spfd and directed.Note :- All Demolition debris Romove from site and disposed out of Military area. 44 M & L 15mm thick rendering on fair faces of brick work / stone masonry, concrete surface in cm 1:6 to be finished even and smooth with out suing extra cement . 45 M & L 15mm thick rendering on fair faces of brick work / stone masonry, concrete surface in cm 1:4 to be finished even and smooth with out suing extra cement using WPC as per manufacturing instruction. 46 M&L Rendering 10mm thick on concrete surfaces as in facia or ceiling in CM 1:3 finished even and fair without using extra cement, complete all as spfd and directed. 47 M&L three coats of white wash on newly plastered ceiling surfaces including preparation of surfaces. 48 M&L one coats of white wash on old surfaces on ceiling including preparation of old surfaces. 49 M&L two coats of OBD over a coat of chalk whiting with apply of 2 to 3 mm thick wall careputty of smooth surfece using of Rolleron newly plastered wall surfaces complete all as specified and as directed. 50 M&L two coats of OBD over a coat of chalk whiting with apply of 2 to 3 mm thick wall care putty of smooth surfece using of Rolleron old plastered wall surfaces complete all as specified and as directed. 51 Material & Labour forProviding and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. 52 Material & Labourfor Complete removal of existing treatment Providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces. 53 M&L for PreparingNew plastered surfaces of walls and appltying three coat of white wash 54 M&L for repairing the edges / corner of Chajja / roof projection and similar work by removing of plaster width / girth exceeding 15 cm & n exc 30 cm and making good with 15 mm thick rendering in cement mortar 1:3 to match with including chicken wiremesh netting on existing surface complete allas specified and directed. 55 S&F PVC (SWR) pipes 75 mm bore dia, single socketed, in any length with rubber ring joints, laid in trenches or in floors etc including taking down and removal from site, complete all as specified and directed. 56 S&F 110 mm bore dia,PVC (SWR) pipes single socketed,inanylength with rubber ring joints, laid in trenches or in floors including taking down and removal from site, complete all as specified and directed. 57 S&F 150 mm bore dia,Sail-glazed stoneware drain pipes laid in trenches and jointedas specifiedincluding taking down and removal from site, complete all as specified and directed. 58 M&L Cement concretebed 1:3:6 type C-2 to 150mm drain pipes inincluding packing under, and haunching againstthe sides of pipes after they are laid and tested; in 59 S&F PVC (SWR) bends 75 mm bore dia complete all as specified and directed. 60 S&F PVC (SWR) bends 110 mm bore dia complete all as specified and directed. 61 S&F PVC SWR floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1(1:2:4) 75mm bore with grating. 62 S&F 75mm PVC (SWR) vent cowl 63 S&F in repair 1000 ltr Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 25 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe (including dismantling of tank ) complete all as specified and directed. 64 S&F Vitreous china squatling pan water closet, orissa pattern, size 580 x 440 mm white with integral foot rests (excluding flushing cistern and flush pipe) including PVS (SWR) S trap,provn of lime concrete and jointing to flush pipecomplete all as specified and directed. 65 S&F Vitreous china, wash hand basin with pedastral pattern (white) of size 550mmx400mm including brass CP waste coupling 32mm dia with long screwed shank and fly nuts, PVC medium grade 32mm dia waste pipe, chain and plug, porcelain stopper , PVC connection 15mm dia, 450mm long with brass CP nuts and washers at both ends complete all as specified . 66 S&F in repairs 10 Liter capacity PVC symphonic action type flushing cistern (ISI Marked) low level with inlet ball valve, float and handle & PVC flush pipe, fixed in position and connecting complete. 67 S&F PVC Connections 15 mm size with PTMT nuts of length 450mm complete all as specified. 68 S&F in repair Chromium plated bib taps 15mm bore cast copper alloy fancy typewith crutch or butterfly, handle, screwed down, screwed for iron pipe. 69 S&F in repair 15 mm bore Chromium plated stop valve/angle cock cast copper alloywith screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions complete. 70 S&F in repair 15 mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete. 71 S&F in repair20 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed as per requirement of the site complete all as specified. 72 Taking up or down 15mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specifed and directed. 73 Taking up or down 20mm bore steel tubing and connection, including cleaning for refixing or removal from sitecomplete all as specified and directed. 74 Taking up or down 25mm bore steel tubing and connection, including cleaning for refixing or removal from sitecomplete all as specified and directed. 75 S&F steel water tubing, 15 mm bore, galvanised , medium grade with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed. 76 S&F steel water tubing, 20 mm bore, galvanised , medium grade with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed. 77 S&F steel water tubing, 25 mm bore, galvanised , medium grade with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed. 78 Cutting chase, pinning inbrick walls in making good to faceing where required and pointing in cement mortar 1:3 to ends or edges of landing, and cutting chase for concealed water tubing or concealed conduit wiring etc and making goodcutting exc 10cm but n exc 20cm. 79 M&L Water proofing treatment on RCC roof etc. comprising with the following operation & as specified herein below:- (a)Taking down existing old tarfelt, bituminous compoundincluding cleaning & removing debris as specified and as directed(b)Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) (c)Preparing & cleaning of fully dried cement concrete surface.(d) Applying one coat of cold bituminous primer to the plastered surface @ 0.30 litres per sqm conforming IS-3384(e) A layer of APP based polymeric membrane3mm thick (minimum) weighing 3.5 kg per sqm reinforced with polyster non woven fabric.The over lap shall be minimum 75 mm in length side and 100 mm with side. Application of polymeric membrane shall be by torch applicationas specified and as directed. 80 M & L 15 mm thick rendering on fair faces of concrete surfaceis incm 1:3 to be finished even and smooth with out suing extra cement under roof treatment mixed with water proofing compound (to be measured and paid seperately) 81 M & L Plain cement concrete, M-15 (Nominal Mix), type B-0,1:2:4 (using 12.5mm graded aggregates) as in roof kerbs, mud stops, roof padding etc using water proofing compound, complete all as specified and directed.Note : WPC compound measured and paid and seperately 82 Supply liquid water proofing compound 83 M&L PCC 1:3:6 type C-2 75 mm thick ( 40mm graded aggregate) thick as in base of tilingfinishing the surface even & fair whtiout using extra cement complete all as specified and directed. 84 M&L 50 mm Fine aggregate (sand) for Cushoning of Paver blocks complete all as specified and directed. 85 M&L Glazed Machine pressed precast concrete colouredinterlocking paver block laid in floor with grey cement and and pigment, any shape and size conforming to IS-15658-2006 of 60mm thickness M-35 grade complete all as specified and directed . 86 Dismantling boarding, any description, fixed in any position with nails 87 S & F 18mm thick lead free factory made 100% solid WPC (wood polymer composite) sheet for cupboard/Kitchen cabinet shutters and frames having high natural fiber content 25 to 30% wood colour sheets with density not less than 500 Kg/cum and weight of sheet of 1 sqm should be 11 Kg (+/-5%) manufactured by ISO 9001-2015 certified company. the sheet should be 100 %water proof , termite proof, fire retardent, manufactured by single layer extrusion process with excellent screw as directed. 88 S&F 2nd class HW plain fillets, square / rectangular,wrought face of sectional area exc 13 & n.exc 25 Sqcm, securing with screw complete. 89 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished, complete all as specified and directed by Engr-in-charge. 90 S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised 30mm. complete all as specified and directed. 91 S&F in repairs 25 mm drapery rod Stainless SteelComplete all as specified and as directed. 92 S&Fin repair drapery rod Brackets both side complete all as specified and as directed. 93 S&F 600mm x 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC plain building board or commercial ply wood and fixed to wooden plug with chromium plated brass screw and cup washers complete as directed. 94 S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates etc conforming to fe-290-w,Gde-E-165,quality A, complete all as specified and directed. 95 Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital orsimilarpattern roof coverings 96 S&F 2mm thick Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc 97 S&FPre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified 98 Demolition of ReinforcedConcrete of any description and in anypositionnot otherwise specifically provided for 99 M&L for Providing, cement concrete 1:3:6 Type C-1 (using 20mm graded stone aggregate as in lintels upto1.5m clear span,cills,steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering,slightly rounded or chamfered angles and throating, as directed 100 S&F in repairsinks with drainage board made of stainless steel 1mm thick kitchen or laboratorywith plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm 101 Surface Excavation not exceeding30 cm deep and averaging 15 cm getting out in soft/loose soil, complete all as specified and directed. 102 Excavation in trenches n exc 1.5mtr wide and n exc 1.5mtr in depth for foundation etc in any type of soil and getting out soil, complete all as specified and directed. 103 M&L 150 mm th hardcore of gauge n exc 63 mm ,deposited ,spread and levelled in layers ,watered and rammed to a true surface. complete all as specified. 104 M&L 75 mm Thick PCC 1:4:8 Type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and as directed. 105 M&L Plain cement concrete, M- 10 (Nominal Mix), type C-2 (using 40mm graded crushed stone aggregates) as in foundation filling and mass concrete,complete all as specified and directed. 106 M&L Brick work with sub class B bricks straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6, complete all as specified and directed. 107 Returning filling in (soil) incl spreading, levelling , watering and well ramming in layers n exc 25cm thick, complete all as specified and directed. 108 Removing of surplus soil to a distance n exc 50 mtr and depositing where directed ata level n exc 1.5 mtr above the starting point, complete all as specified and directed. 109 M&L 15 mm thick plastering incement mortar 1:4on stone/brick surfaces or concrete surface,as on internal surfaces, surface finished even and smooth without using extra cement,complete all as specified and directed. 110 M&L for Rendering 10 mm thick on stone/brick masonry or other than fair faces of brick wall in cement mortar 1:6 finished even and fair without using extra cement,complete all as specified and directed. 111 M&L for Peparation of newplastered or unplastered surfaces of walls and applying two coats of cement base paintwhite or tinted,complete all as specified and directed. 112 M&L for Peparation of newplastered or unplastered surfaces of wallsand applying two coats of Oil bound distemper, white or tinted, complete all as specified and directed. 113 M&L for Non skid coloured/ digital ceramic tiles 7 to 8 mm thick (Square / rectangular) polished area of each tile 300 x 300 mm / 400 x 400 mm as in floors etc laid over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed with coloured cement to match the tiles complete. 114 M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter 115 M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings,girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc 116 M&L for RCC M-20 Nominal mix (1:1.5:3) using 20 mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span 117 S&F Solid PVC door frame of size 50x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, S&F in opening as per specification & drawing shown in SSR Part-II, complete all as spfd and directed. 118 S&F Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tubes for top and bottom rails.MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rails and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to in stiles & rails with suitable PVC sheet beading and joinned together with solvent cement S&F in frames at site as per specification and drawing shown in SSR Part-II, complete all as specified and directed. 119 S&F Aluminium butt hinges,100mm long, B-21 A complete all as specified and directed. 120 S&F Aluminium anodised barrel tower bolt of extruded section, 200mm long complete all as specified and directed. 121 S&F Steel ventilator with top hung shutter incl hinges, steel peg stay, complete with glazing bars dove tailed or welded, complete all as specified and directed. 122 S&F 4.0mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.50 Sqm in each panes. 123 S&F PVC (SWR) pipes 75 mm bore dia, single socketed, in any length with rubber ring joints fixed to walls/ laid in trenches or in floors etc, complete all as specified and directed. 124 S&F PVC (SWR) pipes 110 mm bore dia, single socketed in any length with rubber ring joints fixed to walls/ laid in trenches etc including taking down and removal from site, complete all as specified and directed. 125 S & F 75 mm bore PVC (SWR) T- Junction 126 S & F 75 mm bore PVC (SWR) Bend with ovel acces door 127 S & F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement 128 S&F PVC (SWR) floor trap, plain with grating including jointing with solvent cement 129 S&F PVC (SWR) vent cowl 110 mm dia 130 S&F 500 ltr Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 25 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and directed. 131 S&F Vitreous China wash down water closet pan Europian type(pedestal pattern),connection to trap P or S and flush pipe etc seat cover and making good to disturbed surfaces of floor by filling with PCC 1:4:8 type D-2 to match with existing includingtaking down the existing old one all asspecified and as directed. 132 S&F 10 Ltr capacity PVC symphonic action type flushing cistern (ISI Marked) low level with inlet ball valve, float and handle & PVC flush pipe, fixed in position and connecting complete. 133 S&F oval (colour as directed) counter wash basin of size 560 x 470 x205mmincl CP coupling and waste pipe complete all as specified and directed by Engineer-in-Charge. 134 M&L for 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. 135 Vitreous China urinals, half stall type, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brassscrews, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) 136 S&F Aluminium anodised Tubular towel rail, 20mm dia, 60 cm long, CP with a pair of brackets, fixed to wall with CP screw and PVC rowl plugs ,complete all as spfd and directed. 137 S&F soap dish any type fixed to plugs with chromium plated brass screws. 138 S&F CP bib taps 15mm bore cast copper alloy fancy typewith crutch or butterfly, handle, screwed down, screwed for iron pipe. 139 S&F CP Swan Neck type Pillar taps fancy type 15 mm bore cast alloywith capasten head screwed down high pressure with without lettered Hot or Cold with long screwed shanks and fly-nutsscrewed complete all as spfd and directed 140 S&F 15mm bore Angle valves, CP fancy type (ISI marked)two way screwed down, high pressure with crutch or butterfly handle, screwed both ends (externally threaded) complete all as specified and directed by EIC 141 S&F CP 15 mm bore stop valve/angle cock cast copper alloywith screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions but fancy type, chromium plated with long shank and cup (concealed type) complete. 142 S&F 20 mm Gun metal Gate valves fitted for iron pipe complete all as specified. 143 M & L Colour chequered cement concrete tiles, machine pressed, factory made of size 300 x 300 x 25mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry, laid in floors, over and including 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed by Engr-in-Charge. 144 Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance not exc. 50 m in soft/loose soil and making good surface complete all as specified and directed 145 M&L Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, facia and fixed with selftapping screws as specified. 146 S & F Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc. Fe 410 -W (Gde- E- 250) quality- A complete all as specified and directed 147 S&F Providing and fixing tiled false ceiling of size 595 x 595mm in true horizontal level suspended on interlocking gypric metal grid of hot dipped galvanised steel section (galvanized @ 120 gsm/sqm, both side inclusive) consisting of 3600mm long main T runner size 24x38mm and 0.30mm thick,1200mm long cross T of size 24 x 25mmand 0.30mm thick, 600mm secondary cross T of size 24 x 25mm and 0.30mm thick, bottom exposed capping of width 24mm of all T-sections shall be of 0.25mm thick PPGI, wall angle is fixed along the perimeters of the ceiling to walls, partitions or columns etc with rawl plugs and wooden screws at 300mm centers Main T runners are then suspended from ceiling using GI sloted cleats of size 27x37x25x1.6m fixed to ceiling with 8mm dia and 45mm long dashfasteners, 4mm GI adjustable rods withgalvanised buttrtfly level clips of size 85x30x0.8mmspaced at max 1200mm centre to centre along main T and not more than 150mm from spliced joints.The last hanger at the end of each main runner should not be greater than 600mm from the adjacent wall, then 1200mm long cross T is interlocked between the main T at 600mm center to center to form a grid of 1200x600mm and then secondary cross T of length 600mm is theninterlocked at middle of the 1200x600mm grid to form grids of 600x600mm. Cross tees at the ends having length more than 600mm are to be supported independently. Finally white coloured Gyproc 9mm thick Dew Drop/Granular tiles of size 595x595mm having foil on backside & PVC paper on front side wrapped around edges to be placedin grid complete all as specified and directed. 148 Taking down carefully existing aluminum / copper point wiring (light, fan, socket or power point) complete of any description including fitting such as switches, ceiling roses, pendants, tube light fitting, fan regulators, sockets, wooden boards, laminated sheets from sunken boxes, boards, shades light fitting etc and making good the disturbed surfaces of walls, floors, ceiling etc to match with existing surfaces complete all as specified and directed. 149 Taking down un-serviceable DB of any size and capacity including MCB etc, and removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls,floors, etc, complete all asspecified and directed. 150 Taking down un-serviceable sub main wiring of any type and any size from wall, ceiling etc. complete all as specified and directed. 151 M&L for point wiringwith 1.5 Sqmm (nominal area) PVC insulated FRLS and unsheathedmultistranded copper conductor cable 1100 volts grade drawn through and including PVC rigid Concealed conduit not less than 1.8 mm thick (ISI marked) with all accessories including bends, cross, elbows tees etc of suitable size including concealed MS pressed steel (Modular sunken box) terminal box not less than 1.6 mm thick for mounting switches, sockets, fan regulators etc and Modular cover plate as top cover (ISI marked) including 1.5 sqmm PVC FRLS insulated unsheathed copper conductor multi stranded cable for continuous earth conductor connected to common arth dolly , complete all as specifid and directed for the following :- Note- (a) Proper colour coding is to be followed as per IS specification. (b) Point wiring considered for Modular switches and sockets, rate of metallic sunken box and modular sheet cover plate and other connected accessories required for modular point wiring included in quoted rate. (c) Rate of modular switch and sockets will be paid seperately under relevant item. 152 One light controlled by one switch 5 Amp , SP , one way 240 volts 153 One Ceiling /Exhaust fan point controlled by one switch SP , one way, 5 Amp , 240 volts. 154 One multi pinsocket outlet 5 amp independent . 155 One multi pinsocket outlet 5 amp same board . 156 All as per the description of Serial Item No. 151.00 above but using 2.5 sqmm (nominal area) multistranded copper conductor cable & 2.5 sqmm size PVC insulated FRLS and unsheathed copper conductor cable FRLS for earth continuity (green colour) for one 3 pin socket outlet 15 Amp multipurpose independent point controlled by16 Amps switch ,SP ,one way ,240 volts for socket ,complete all as specified and directed. 157 S&FSocket, 6A - 2/3 pin combined 2 module, 240 volts ISI marked complete all as specified and directed. 158 S&F Socket 6A/16A - 2/3 pin combined 2 module, 240 volts ISI marked complete all as specified and directed. 159 S&F Modular Switch one way 6 Amp, one module 240 volts ISI marked complete all as specifiedand directed. 160 S&F Modular Switch one way 16 Amp, one module 240 volts ISI marked complete all as specifiedand directed. 161 S&F ceiling rose surface bakelite 63.5 mm dia three terminal complete all as specified and directed. 162 S&F modular type fan step regulator 120w two module complete all as specifiedand directed. 163 Supply & fixBEE 5 star rating energy efficient ceiling fans 1200 mm sweep (BLDC) with minimum air delivery 210 cum/min, down rod all accessories required including regd length of 3 core 1.0 sqmm PVC multistranded copper conductor, PVC connector for proper hanging of fan and testing complete all as specified and directed. 164 Supply & fixExhaust fans made of sturdy Engineering plastic complete with louvers shutter, 230 Volt, 50 Hz, RPM 1200, copper winding of sweep 300 mm, incl all fixing accessories required including making hole & regd length of 3 core 1.0 sqmm PVC multistranded copper conductor,and testing complete all as specified and directed. 165 S&FLamp holder with metal ring, PVC/Polycarbonate type with back plate suitable for batten fittings non ISI Marked complete. 166 S&F LED Bulb09/10 watt with provision of fixed in Lamp holder complete. 167 S&F Decorative ultra slim LED Tubelight fitting of LEDwith extruded polycarbonate, enviormental friendly energy efficient ready to use, 20 watt, 6500K fitting, incluing reqd length of not less than 1.0 Sqmm PVC multistranded BIS marked 03/02 core copper conductor forelectrical connection from ceiling rose to connector of LED fitting including testing on completion all as specified and directed. 168 S & F security light fittings better optics for uniform distribution IP 65 protection LED of 30 watt, Heat resistance glass, pressure die cast aluminium housing including 25mm dia galvanised iron pipe light grade bracket bent to shape over all length 0.60mt fixed to wall with 02 Nos Fl clamps made of 40 x 5 mm Fl, 15 cm long, 8 mm dia bolts and nuts with washers grouted in wall complete including rend length of 1.5 Sqmm PVC multistranded BIS marked, 03 core copper conductor for connection from ceiling rose to light fittings incl testing on completion all as specified and directed 169 S&F sheet metal enclosure double door distribution board factory made for MCB DB load link VTPN 4 way suitable for MCCB as incomer, 100 Amp,4 pole & Including MCCB 100 amps 4 pole 16 KA complete. (when MCBs are to be used) with suitable size of busbar complete,fixed flush in wall including chases wall for fixing DB and making goodthe distributed wall surfaces to match with existing specification including taking down all as directedby Engr-in-Charge at site. 170 S&F MCB DB, sheet metal enclosures double door SPN 12 way with bus bar 240 volts 2 in 1 shutter type (METAL DOOR)type with blanking plates where required and IP 43 degree protection complete all as specified and directed. 171 S&F, MCB SPN 63 Amps, 240 volts C series 16 KA ,including connection with suitable size copper lugs complete all as specified and directed. 172 S&F, MCB SP 240 volts, 6to 32 Amps, C series 10 KA including connection with suitable size copper lugs.complete all as specified and directed. 173 Taking down old unserviceable electric water geyser, S&F new electricstorage Heater (vertical type Geysers) 25 Ltrs BEE RATING 5 STAR, 230 volts AC single phase with and including grouting with high tensile rag bolt, nut & washer etc as directed as per site requirement and making necessary inlet / outlet water connection for Geysers. Geysers to have glass lines tank, fero glass coated container, PUF insulation, glass coated heating element, thermostat cut off etc. complete all as specified and as directed. 174 S&F sheet metal enclosure, single pole and neutral with a two pin and earth plug and socket with and including one single pole MCB 20. Amps, 240 volts, 10 KA complete all as specified and directed. 175 M&L, sub main wiring with two single core PVC insulated unsheathed FRLSH confirming to IS 694:2010, multi stranded copper conductor (ISI marked with valid CML No), cable 1100 Volt grade, 4 sqmm size drawn in and including non metallic rigid PVC concealed conduit medium grade (ISI marked with valid CML. No) not less than 25 mm dia confirming to IS 14930 (Part-1) 2001, with all fitting & fixing accessories including one run single core PVC insulated unsheathed 4 Sqrım FRLSH copper conductor (ISI marked with valid CML No) colour code as a earth continuity and connected upilo DB complete all as specified and directed (NOTE: (i) Two run of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit and the quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface with putty to match with the existing surface. 176 M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) vertically, with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of MES Schedule Part-I connecting to earthing test. Testing on completion with and including necessary excavation and earth work in any type soil, earth lead connected to earth test point & to main switch board etc with & including adequate quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 (using 20mm graded BT stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, internal surface of concrete shall be given 10mm thick plaster in CM 1:4, pre cast RCC (1:2:4)type B-1 (using 20mm graded BTstone aggregate) 40mm thick cover, reinforced with 8mm dia deformed or TMT bars 3 Nos both way with 12 mm dia round bar handle, GI medium grade watering pipe 20 mm dia with funnel and wire mesh and 15mm dia GI medium grade earth lead protection pipe including provn of earth test point made of 50 x 5 mm MS Flat in D shape 500 mm legth grouted in wall complete 01 x 6 Sqmm multistrand PVC insulated copper conductor ( Green Colour) to be provided from test point to DB through 20 mm dia concealed non metallic conduit complete all as specified and directed. 177 Supply, laying and testing cable XLPE insulated screend PVC bedded, galvanised steel strip or wire armoured electric power cables (Heavy duty) 1100 V grade with stranded aluminium conductor of size 25 sqmm x 4 Core,laid in trenches or passing through pipe including taking down of existing cable/service connection of any type or size and removing from site to MES store for reuse if serviceable or for credit all as specified and directed and directed by Engr-In-Charge. 178 Sand filling in trenches with clean dry unwashed sand free from sharp particles, gently punning around the cables complete. 179 Brick, old size sub class B laid in trenches with width wise along the alignment of the cable as protection complete. 180 S&F tube light grade galvanised with all fitting laid in trenches, fixed to wall and floor of 40 mm dia for cable protection complete all as specified and directed. 181 S&F tube medium grade galvanised with all fitting laid in trenches,of 40 mm diacomplete all as specified and directed. 182 S&F tube medium grade galvanised with all fitting laid in trenches,of 25 mm diacomplete all as specified and directed. 183 S&F tube medium grade galvanised with all fittingfixed to wall and floor of 20 mm dia for cable protection complete all as specified and directed. 184 S&F in repair40 mm bore gun metal, gate valve, heavy duty confirming to IS -778with iron wheel head, screwed both ends for iron pipe completeincluding taking out old un-serviceable one all as specified and directed. 185 S&F in repair20 mm bore gun metal, globe or gate valve, heavy duty confirming to IS -778with iron wheel head, screwed both ends for iron pipe complete including taking out old un-serviceable one all as specified and directed. 186 S & F in replacement ball/float valve high pressure ofPTMT with epoxy coated alumunuium rod and high density plastic ball screwed for 20 mm bore GI tubing complete all as specified and directed.Make- Prayag or approved by GE. 187 M&L construction of valve pit of inner sizes up to 60 cmx 60cm x 60cm brick masonry construction completeAll internal surface and external surface upto 15 cm below normal ground level of brick masonry shall be plastered 15mm thick in cement mortar 1:4, finish even and smooth including necessary excavation and earth work in any type of soil and PCC work all as per TD drg complete all as specified and directed. 188 S & F factory made DB SPN 4 way double door with 200 Amps rated bus bar concealed in wall IP 42/43 protection, 240V for fixing MCB & making good to disturbed surfaces as well as matching with existing whitewash color/surfaces complete all as specified and directed.Note: Distribution board and MCBs should be same make. 189 S&F 240V, 10 KA C curve miniature circuit breaker (MCB) ofsingle poles and current carrying capacitySP 6 to 32 Amp, in the MCB DB complete with connection testing and commissioning complete all as specified and directed. 190 S &F of SPN 40 Amp rating 240V, 10KA C curve miniature circuit breaker (MCB) current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed. 191 Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 6 sq. mm2 core in service connections complete all as specified and directed. 192 S&F Exhaust fan made of Strudy Engineering plastic complete, AC single phase, 230V of size 250 mm sweep with blades, and frame and Louvers, energy saving including cutting of wall all as specified and directed by Engr - in - Charge.
