Tender For Entry Gates, Barriers And Booking Window On Entry Routes To The Sanctuary Shergarh. - Earth work in rough excavation, banking excavated earth inlayers not exceeding 20cm in depth, breaking clods watering,rolling each layer with 1/2 tonne roller, or stone or steelrammers and rolling every 3rd and top- most layer withpower roller of minimum 8-10 tonne capacity and dressing upin embankment for roads, flood banks marginal banks andguide banks or filling up ground depressions, lead up to 50Mtr. and lift up to 1.5 Mtr.:All kinds of soil 2 Random rubble dry stone Kharanja under floor. 3 Providing and laying in position cement concrete includingcuring, compaction etc. complete in specified grade excludingthe cost of centering and shuttering - All work up to plinthlevel.M10 grade Nominal Mix1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate40mm nominal size). 4 Random Rubble stone masonry with hard stone insuperstructure above plinth level and upto five level above30cm. thick walls in :Cement Mortar 1:3 ( 1-Cement : 3-Sand). 5 Providing and laying damp-proof course with cement concrete grade M-150 (1 : 2 : 4) mortar prepared with 1% solution of water-proof compound complete as per specification .75mm thick. 6 Centering & shuttering with plywood or steel sheets includingstrutting, propping bracing both ways with steel props andremoval of formwork for upto floor five level for :Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills, chhajjas, lintel, beam, plinth beam etc. 7 Providing and laying in position specified grade of cementconcrete for RCC structural elements upto floor five levelincluding curing, compaction, finishing with rendering incement sand mortar 1:3 (1 cement: 3 coarse sand) and makinggood the joints and cost of plastizers (if required ) excludingthe cost of centering, shuttering and reinforcement for Walls(any thickness) including attached pilasters, buttresses, plinthand string courses, fillets, columns, pillars, piers, abutments,posts and struts etc. M20 grade Nominal Mix / Design Mix 8 Providing and fabricating reinforcement for R.C.C. workincluding straightening, cutting, bending, placing in positionand binding (including cost of binding wire) all complete up tofloor five level. Thermo-mechanically Treated bars (Conforming of relevent IScode) 9 Labour charges for cutting, bending for fabrication andbinding reinforcement (plain or tor/ribbed/TMT steel) as perdrawing and design for R.C.C. and R.B. work including cost ofbinding wire with all lead and lift up to floor five levelcomplete. 10 Brick work in gauged arches in super structure upto five storeyin cement mortar 1 : 3 including centering and shutteringcomplete span upto 6 meter with Brick of class designation 75. 11 Plaster on new surface on wall in cement sand mortar 1:3including racking of joints etc. complete fine finish :25 mm thick 12 Providing and fixing Granite stone slab mirror polished andmachine edge cut in walls, pillars, steps, Shelves, SillsCounters, Floors etc. laid on 12mm (Av.) thick base of cementmortar 1:3 (1 cement : 3 coarse sand) jointing with whitecement mortar 1:2 (1white cement : 2 marble dust) withpigment to match the shade of the marble slab includinggrinding, rubbing and polishing complete.Jhunjhunu / Jalore (Red/Choclate/Black/Pink Colour)Above 3601 Cm2 Slabs 13 Providing and fixing steel gate, grating , and grills made ofangles, tees, square bars, flats,or black pipe with holdfast andfittings complete as per design and drawing including cuttingwelding and fabrication with priming coat of red oxide 14 Extra if square,rectangular hollow tubelar sections are used orgrill made by flats only 15 Wall painting with plastic emulsion paint of approved brandand manufacture to give an even shade including allscaffolding:Two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect 16 Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & its ISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thick HotDipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheets & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure Aattached with this BSRMedium point (up to 6 mtr.) 17 Long point (up to 10 mtr.) 18 P & F 1.2mm thick M.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side . All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure A attached with this BSR 19 Providing & Fixing of 1200 mm sweep BLDC technology power saving ceiling fan which can withstand on votage fluctuations from 140 volts to 240 volts ,power factor not less then 0.9 , service value (CMM/W) minimun 6.85 , air delivery minimun 220 CMM, speed minimum 330 RPM ( tolerance as per IS:374 2019 ) THD less then 10% and complete with down rod of 15 mm dia . ERW (Electrical resistance welded ) of 1.6mm nominal thick medium duty steel pipe up to 80 cm , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR . Without Remote 20 PProviding & Fixing of energy efficient /energy saving IP 20 LED direct retrofit Bulb in existing holder or fixture as required with system lumen efficacy ≥100 lm/Watt output ,pf 0.95 , CRI >70, minimum life time of minimum 25000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate /Report from OEM shall be submitted. All as per pre approved by engineer in charge . for additional technical parameters of product/ work, refer Annexure A attacheded with this 18/20 Watt 21 Providing & Fixing of IP20 SMD Mid Power LED batten with integrated box (min.1200mmx40mmx60mm including reflector) with replacable driver fixture made from Powder coated Extruded aluminium housing ,Min. lumen output 4400 lm, System lumen efficacy ≥ 110 lm/Watt output, internal surge protection of 4.0 KV with Short & Open circuit protection,THD < 10% , P. F.≥0.95, CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not more than the specified rating and Fixture shall be of BIS standardand trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR . 22 Applying priming coat :With ready mixed red oxide zinc chromate primer of approved 23 Painting with synthetic enamel paint of approved brand andmanufacture to give an even shade Two or more coats on new work 24 Supply and fixing Jodhpur sand stone Machine cut Kerb stone(10cm wide 40 cm. height) fixed in white cement sand mortar1:4 with pigment including EarthWork. 25 Forming groove of uniform size 15x15mm and upto 25x15mmin the top layer of washed stone grit plaster as per approvedpattern using wooden battens, nailed to the under layerincluding removal of wooden battens, repair to the edges ofpanels and finishing the groove complete as per specificationand direction of Engineer in charge 26 Extra for using white cement in place of ordinary cement inthe top layer of the item of washed stone grit plaster. 27 Extra for plastering done on moulding cornices or architravesincluding neat finish to line and level:In two coats 28 Encasing rolled steel section in beams and columns, with M20Nominal Mix cement concrete including centering andshuttering complete but excluding cost of reinforcement. 29 Providing and fabricating reinforcement for R.C.C. workincluding straightening, cutting, bending, placing in positionand binding (including cost of binding wire) all complete up tofloor five level. Thermo-mechanically Treated bars (Conforming of relevent IScode) 30 Labour charges for cutting, bending for fabrication andbinding reinforcement (plain or tor/ribbed/TMT steel) as perdrawing and design for R.C.C. and R.B. work including cost ofbinding wire with all lead and lift up to floor five levelcomplete. 31 Wall painting with Royal Play paint with various types ofdesigns as approved of approved brand and manufacture togive an even shade including all scaffalding.Two or more coats on New work including preparation of basewith primer, putty lippy etc. Complete in all respect 32 Mason (for ornamental stone work) 1st class 33 Beldar
