Tender For Special Repair To Bldg No P-01 And P-01F At Naa Under Ge (N) Tezpur; 1 Dismantling of floor/ wall tiles including cement mortar bedding of any thickness upto PCC/ RCC/brick surface and rubbish off the premises, complete in all respect all as specified and directed. 2 Dismantling CGI sheet, ridge(corrugated, semicorrugated, plain etc.) in roof covering,wall etc or of similar types complete allas specified and directed. 3 Dismantling of timber scantlings 40 sqcm & over in section framed work complete all as specified and directed. 4 S &F second class hardwood plain,solid ,straight,chowkats and frames,wrought, framed rebated on the solid ,rounded or chamfered,put together with glue pinned at joints, complete in all respect as specified and directed. 5 S&F coloured 0.50mm thick pre-painted galvalume aluminium zinc coating GI based trapezoid profile steel sheethaving tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws alongwith bitumen washer complete allas specified and directed. 6 S&F coloured 0.50mm thick pre-painted galvalume aluminium zinc coating GI basedtrapezoid profile steel sheethaving tensile strength of 550 Mpa as in ridge, valley gutter or of similar type, fixed with self tapping screws alongwith bitumen washer complete allas specified and directed.Note- The measurement shall be carried out as in a plain sheet. 7 Dismantalling of cement concrete (unreinforced) in ground floors and pavings not exceedings 15 cm thickness (below or above ground level), complete in all respect as specified and directed. 8 M & L including installation and testing for modular kitchen of size 3.5 X 2.5 with following accessories, complete all as specified and directed.(a) Handle type - SS handle fancy type 128mm size- 22 Nos(b) Carcase- Prelaminated ply, 18-19 mm thick ply over 0.9 mm thick decorative C1 of surface finish, colour and pattern as approved by GE.(c) Kitchen chinmey of 60cm, 1250 m3/hr. suction motor FRP, 180watt wall mounted 3 speed setting with filter less auto technology with motion sensor and touch control curved glass - 01 Nos(d) Basket (i) Stainless steel designer cup and saucer basket of size 530mm wide, 505 mm depth and 100mm height - 01 No (ii) Satinless steel perforated peep hole cutley basket of size 530mm wide 505 mm depth and 100 mm height - 01 No (iii) Stainless steel designer plain basket of size 530mm wide 505 mm depth and 150mm height - 01 No(iv) Stainless steel pull out basket of size 160mm wide 505 mm depth and 530mm height- 01 No (v) Stainless steel designer thali/ plate basket comb of size 530mm wide 505mm depth and 200 mm height - 02 Nos(e) Stainless steel magnetic catcher of size 5.08 X 2.54 X 2.54 cm for cabinets and shelves - 34 Nos.(f) Channel - Soft closing telescopic channel 18 size (45 kg) suitable for basket/ drawer.(g) Auto closing consealed hinges 9.5 crack for half overlay doors with 95 degree opening angle 14-32 mm zinc coating - 68 Nos 9 Taking down chowkhats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm and n.exc 4 sqm each, complete in all respect as specified and directed. 10 Taking down cement plaster of any thickness and description on brick/ concrete/ stone wall/ ceilings, etc, including raking out joints, hacking for key, scrubbingdown with water etc, complete in all respect as specified and directed. 11 Providing and laying for cement concrete in coping, hold fasts using type B-1, 1:2:4 (using 20 mm nominal size crushed and graded stone aggregate) or of similar type of work including necessary formwork complete in all respect as specified and directed. 12 M&L for 25 mm thick of cement concreteflooring using type B 0, 1:2:4 (using 12.5 mm nominal size crushed and graded stone aggregate) and finished fair and even without using extra cement, complete in all respect as specified and directed. 13 Providing and laying skid/non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floor etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 15 mm thick screed bed in cement mortar (CM) 1:6, complete in all respect as specified and directed. 14 Providing and laying coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.08 sqm but not exceeding 0.15 sqm, in skrting/dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 15 mm thick rendering in cement mortar (CM) 1:4, complete in all respect as specified and directed. 15 Dismantling wrought iron or mild steel work of any description not otherwise provided for etc complete in all respect as specified and directed. 16 S&F Rooftrusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, tubular/hollow section, channel or flat sections) including distance pieces, cleats etc. using Fe-410W (Grade E-250 quality A) including necessary welding complete complete allas specified and directed. 17 M&L 15 mm thick plastering on brick/ stone/ concrete surfaces of wall in cement mortar (1:4), finished even & smooth without using extra cement, complete in all respect as speicifed and directed. 18 M&L 15 mm thick plastering on brick/ stone/ concrete surfaces of of wall in cement mortar (1:6), finished even and smooth without using extra cement, complete in all respect as spefied and directed. 19 Supply only water proofing compound complete, in all respect as specified and directed. 20 S&F exposed GI powder coated snap grid frame work for false ceiling in flat or in sloping, of grid size 600 x 600 mm comprising of wall/ cleat angle of size 25x25x0.35 mm and corss tee of size 24x38x0.70 mm with 4 mm dia GI wire as suspender and including 4 mm thick decorative pre-painted non asbestos board (E-Board) in false ceiling including fixing arrangement from steel/ wooden truss of any type including dismantling of existing false ceiling boards, complete in all respect as specified and directed. 21 Providing and laying plinth protection of 75mm thickcement concrete, using type C-1, (1:3:6) (using 20mm nominal size crushed and graded stone aggregate), laid in alternate penals/bays and finished the surafce even and smooth without using extra cement complete in all respect as specifified and directed. 22 S&F 250mm length of bolt, Aluminium anodised, barrel tower bolt of extruded section complete allas specified and directed. 23 S&F 125 mm size, Aluminium handle cast type anodised complete allas specified and directed. 24 S&F aluminium anodised sliding door bolts with hasp and staple (boil type) 19mm dia bolt 300 mm long complete allas specified and directed. 25 S&F 30 mm thick Flush shutters, solid core construction, with block board core with decorative face veneers with lipping on both sides, complete in all respect as specified and directed. 26 S&F 100mm size Stainless steel butt hinges complete allas specified and directed. 27 M & L brick work with sub-class B, old size bricks of class designation 75, straight or curved on plan exc. 6m mean radiusbuilt in CM (1:6) including dismataling of brick work built in cement mortar in any position complete in all respect as specified and directed. 28 S&F 35mm thick second class HW glazed and skeleton shutters, open rebated and prepared to receive glass gauge etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass etc.; sizes of members of shuttrs as specified in SSR Part-I, section 8, clause 8.24 (a), complete in all respect as specified and directed. 29 M & L for Virified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles complete in all respect as specified and directed. 30 M&L for 15mm thick screed bed or bedding layer of mortar in CM 1:4 fixing of tiles in floor complete all as specified and directed. 31 Providing and laying coloured ceramic tiles 8 to 10 mm thick (square/ rectangular) area of each tile exceeding 0.42 sqm but not exceeding 1.0 sqm, in skrting/dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 15 mm thick rendering in cement mortar (CM) 1:4, complete in all respect as specified and directed. 32 M&L for complete removal of existing treatment on wall and applying two coats of oil bound distemper (OBD) and finished another one coat with spunge roller over one coat of alkali resistant priming paint over 2 mm thick (in two layers) wall care putty, complete in all respect as specified and directed. 33 M&L for preparation of old decorated plastered surface of wall after complete removal of existing treatment and applying two coats of weather coat over 2 mm thick wall care putty (in two layers) over a coat of primer including preparation of surface, complete in all respect as specified and directed. 34 M&L for preparation of new undecorated wooden surfaces with pre mixed wood filler used as putty of grith exc 10cmand applyingtwo coats of synthetic enamel paintover one coat of pink primer before painting complete all as specified and directed. 35 M&L for preparation of new undecorated steel surfaceswith pre mixed steel filler used as putty for steel work and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer before painting complete all as specified and directed. 36 M&L for preparation of newly plastered surface of wall and applying two coats of weather coat over 2 mm thick wall care putty over a coat of primer including necessary preparation of surface, complete in all respect as specified and directed. 37 M&L for preparation of newly undecorated plastered surface of wall and applying two coats of oil bound distemper (OBD) and finished another one coat with spunge roller over one coat of alkali resistant priming paint over 2 mm thick (in two layers), wall care putty, complete in all respect as specified and directed. 38 M & L for point wiring with 1.5 sqmmFRLSH, PVC insulated stranded copper conductor single core including non metalic PVC conduit medium grade (MMS ISI) of size not less than 20 mm dia(or as site requirement) concealed in wall/over ceiling, pressed steel concealed terminal boxes of required size and with modular fittings complete with all accessories and all as specified including 1.5 sqmm FRLSH PVC insulated sheathed multistranded copper earth conductor to common earth and connected to earth dollyfor light / fan/ bell point controlled by one switch.Note:- (i) Cost of PVC conduit, steel terminal boxes,modular plate cover etc; are deemed to be included in the quoted rate.(ii) M&L for cutting chases on walls / ceilingand making good disturbed surfaces including finishing with cement mortar (1:3) etc; are deemed to be included in the quoted rate. 39 All as per item 38 above but for One 3 pin socket outlet 5 Amps on same board. 40 All as per item 38 above but for One 3 pin switch socket combination 5 Amps on indpendent board 41 All as per item No.38 above but with 4 sqmm single core multistranded copper conductor FRLSH cable for 3/5 pin 15 Amp socket outlet on independent board. 42 S & F Modular switch 1 way 10 A 1 module module complete all as directed. 43 S & F Modular Socket 6 A 2/3 pin combined 2 module 44 S & F Modular Socket 6 A /16 A-2/3 pincombined 2 module 45 S & F in replacement ofceiling rose polycarbonate typethree terminals complete all as specified and directed. 46 M&L for taking down and refixing of LED light fittings of any type and size after disconnecting from ceiling rose carefully. Note : Any damage occurred to fittings during taking down and refixing contractor has to fix as new fittings and no cost paid to contractor . 47 Taking down ceiling fan any type/ size from hook and dismantling cable and blades and bring in to contractor store for repair and hanging ceiling fan in position after repair, greasing etc. with existing flexible copper cable complete all as directed. (Circuit of fan required shall be included in the quoted rate) 48 M&L for submain wiring with two single core 6 sq mm FRLSH PVC insulated copper cable 1100 volts grade multi stranded, sheathed conductor in concealed PVC conduitincluding 6 sq mm multi-strand FRLSHPVC insulated copper wire for earth continuity conductor connected to common earth dolly complete and making good disturbed surface complete.Note:- Cost of PVC conduit, cutting chases on walls and making good disturbed wall surfaces including finishing with cement mortar (1:4) matching with the existing shade / tint are deemed to be included in the rates quoted. 49 M&L for submain wiring with two single core 4 sq mm FRLSH PVC insulated copper cable 1100 volts grade multi stranded, sheathed conductor in concealed PVC conduitincluding 4 sq mm multi-strand FRLSHPVC insulated copper wire for earth continuity conductor connected to common earth dolly complete and making good disturbed surface complete.Note:- Cost of PVC conduit, cutting chases on walls and making good disturbed wall surfaces including finishing with cement mortar (1:4) matching with the existing shade / tint are deemed to be included in the rates quoted. 50 S & F sheet metal enclosure double doorfor MCB DBs SPN 08 way 240 V, complete flush mounted all as specified and as directed. 51 S & F sheet metal enclosure double doorfor MCB DBsVTPN 08 way 415 V,including 125 Amp MCCB as incomer complete flush mounted all as specified and as directed. 52 S & F sheet metal enclosure double doorfor MCB DBsTPN 04 way 415 V, suitable for 63/100 Amp MCCB as incomer complete flush mounted all as specified and as directed. 53 M&L for MCB Isolator Four pole 63 Amp 415 Volt all complete as specified. 54 S & Fsingle pole and neutral enclouser with atwo pin and earth plug and socket complete with one pole MCB 20 Amps complete all as spd and directed . 55 S & FMCB single pole (SP) 10 to 40 Amps,240 volts , C curve , AC , 50 Hz ,10 kA complete all as specified and directed. 56 S & F MCB Single pole & neutral (SPN)63 Amps, 240 volts , C Curve, AC , 10 kA complete all as specified and directed. 57 M&L for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6mm thick buried directly in ground ( earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 Metre below normal ground level connected to GI wire 4 mm dia by means of bolts, nuts , check nuts and washers of GI and GI tubing 15 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) type C1 pre cast RCC (1:2:4) type B1 cover slab 54 x 54 x 5 cm with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (LG) for watering, charcoal or coal and salt in alternate layers including excavation earth work complete all as shown on electrical plate No. 3 of SSR part - I , including taking out old U/s complete alll as specified and directed . 58 NOTES:1.The amount of schedule of credit shall be deducted from the total of this BOQ for arriving at contract sum.2.The rates for RCC/PCC shall deemed to include the cost of formwork, shuttering etc., required for complete and proper execution of the item. Refer Schedule A notes for details.
