Tender For Major Repair Work At Anganwadi Dahmoli Block Karauli District Karauli; 1 CIVIL WORK 2 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer-in-charge.1: 3: 6 or richer mix. 3 Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge in cement mortar. 4 PCC in foundation :Providing and laying in position cement concrete including curing compaction etc. complete in spcified grade excluding the cost of centering and shuttering all work upto plinth level 1:4:8(1 cement:4 Coarse sand :8 graded stone aggregate 40 mm nominal size). 5 Glazed Window : Providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section joints mitred and welded with steel lugs 13 x 3 mm , 10cm long embeded in cement concrete block 15 x 10 x 10 cm of 1:3:6(1 cement: 3 Course sand : 6 gradred stoneaggregate 20mm nominal size )or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4 mm thick with copper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approval steel primer , excluding cost of metal beading and other fitting except necessary hinges of pivots steel handles peg stay etc. as required : Partly fixed and partly openable ( fixed area not to exceed 33% ) 6 Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance. 7 Guard Bars: Providing and fixing square bars or other flat welded to window/ventilators etc., Guard bar 10 x10mm 8 Internal Plaster : Plaster on new surface on wall in cement sand mortar 1:6 including raking of joints etc. complete fine finish: 12mm thick 9 External Plaster : Plaster on new surface on wall in cement sand mortar 1:6 including raking of joints etc. complete fine finished 20 mm thick. 10 Grading roof for water proofing treatment withwater proffing compound Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 11 Gola Providing gola 75mm x 75mm in cement concrete 1:2:4(1 cement: 2 coarse sand: 4 stoneaggregate 10 mm and down gauge) including finished with cement mortar 1:3(1 cement: 2 fine sand) as per standard design. 12 PANTING ON DOORS & WINDOWS:- Painting with syntheitic enamel paint of approved brand and manufacture in all shade to give an even shadenew steel work (2 or more coat on new work). 13 Brick work with F.P.S. bricks of class designation 75 insuperstructure above plinth level upto floor V level in all shapes and sizes in : Cement mortar 1 : 6 (1 cement : 6 coarse sand) 14 Copping: Providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls(any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, copping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor five level excluding the cost of centering and shuttering. M20 grade nominal Mix 1:1.5:3(1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size) 15 P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant. 110 mm dia 16 P/F reinforcement for RCC work including straightening,cutting, bending, placing in position and binding (including cost of binding wire)all complete upto floor five leveTMT bars (Conforming of relevent IS Code). 17 Supplying and fixing stone lintels/bed plates of approvedquarryroughdressedincement mortar 1:4 : up to 15 cm thick. 18 Wiring of light point/ fan point/ exhaust fan point/ call bell point as per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) inrecessedISI marked ( IS:9537 P - II ) rigid steel conduit & its all accessories, round tiles, Hot Dipped Galvanized Modular Box of 18 SWG with earth terminal, 6 A Modular switch,3 pin ceiling rose / lamp holder/ 3 point connector ,Modular face plate with grid plate, pvc bushes, check nuts, screws etc, all as per pre approved by Engineer in charge, making connections, testing etc. complete as required.Light point & Fan Point 19 Short point (up to 3 mtr.) 20 Medium point (up to 6 mtr) 21 Long point (up to 10 mtr) 22 Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from99.90% purity copper, class 5 stranding in acc. to IEC 60228 forlower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation PVC type A/C/D ,flame retardant as per IS 10810-53, better amperage rating as per IS:3961 PART 5 inin existingsurface or recessed PVC/ MS conduit/casing capping makingconnections with copper lugs of suitable size, Ferrules, testing etc. as required OEM must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of products/work refer Annexure-A attached with this BSR. 2 x 2.5 sq. mm. + 1x1.5sqmm 23 Providing & Fixing of 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C tripping characteristic as per type of load andsite requirement) 4KV impulse withstand voltage,as per PWD specification for electrical Works with ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per IEC,minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , IP 20 contact protection and fitted withexisting distribution board/sheets, min. operation 20,000 upto 32 A rating and 10,000 upto 63 A, 5000 for 80 A ratingincluding making connections, testing etc. as required. 6 A to 32 A rating. 24 Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from polycarbonate /extruded aluminium powder coatedhousing with in built driver, Power Consumption of18W/20W ,system lumen efficacy ≥ 120 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% ,p.f.≥0.95, CRI >80 , life time of minimum50000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. 4 LED Tube shape fixture 18/20 W (Polycarbonate Base) For additional technical parameters of products /work refer Annexure A attached with this BSR 1.17 mm (+/-10%) LED batten with minelumen output 2200. 25 Providing & Fixing of ISO Certified company made BEEStar rated copper wounded double ball bearing capacitor start, aluminium body & Metallicblade ceilingfanas per PWD specification for electrical Works, conforming to IS:374-2019, & IS:1885 -P-V- 1981. with down rod up to 30 cm with secondary support safety cable ( steel wire ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. 1200 mm Sweep BEE 3 Star rated (service value >=5.0 to< 5.5 ) 26 Providing & Fixing of ISI marked (IS:1258)6 ampbatten/angle lampholder with CM/L no. printed and made out from industrial agade Polycorbonate ABS material, brass terminal & captive screws including making connection testing etc. as required.All as per pre approved by Engineers incharge for additional technical parameters of products/wor refer AnnexureA attached with this BSR. 27 P & F 18 swgM.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm,12 mm dia rod fan hook with 100 mmlength extended on each side . All as per pre approved by Engineer in charge. 28 Providing & Fixing of modular type 120 w Step Fan regulator duly ISI marked (IS :11037:1984)with CML no. printed made out of unbreakableand fire retardant vergin poly carbonate with brass terminals and captivescrews & silver alloy contact tip with IP-20 rating, including all as per preapproved buy engineers incharge making connections, testing etc. as required for additional technical parameters of product/work refer Annexure Aattached with this BSR 5 step fan regulator 2 module 360 degree rotating. 29 P &F 12 mm thick G.I/ MS sheet boxes duly finished with two coats of red oxide and with earthing terminal of followingsizes in recessed/ surface as required. For additional technical parameters of products/work refer Annexure A attached with this BSR 1.2 mm thick M.S. sheet boxes 175mm x 100 mm x 60 mm.
