|
| 1 | Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) includingdisposal of excavated earth lead upto 50meters and lift upto 1.5 m,as directed by Engineer-in-Charge. |
| 2 | Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: All kinds of soil : |
| 3 | Dumping stone including cost of stones. in Horizontal on level |
| 4 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:4:8 (1 cement : 4 coarse sand : 8graded stone aggregate 40 mm nominal size) |
| 5 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers,abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size |
| 6 | Random Rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level and curing complete with: Cement mortar 1:6 (1 Cement : 6 coarse sand) |
| 7 | Dry random rubble masonry with hard stone in foundation and plinth: Without bond stone |
| 8 | \"Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo-Mechanically Treated bars of grade Fe-500D or more.\" |
| 9 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 10 | Providing & fixing stabilized mud concrete solid blocks (adobe) with 3% cement,masonry up to floor five level including hoisting and setting in position in cement mortar 1:6 using approved quality mud with carriage of material complete. |
| 11 | Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per directionof Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately). |
| 12 | Providing & fixing upto floor five level precast cement concretesolid blocks including hoisting and setting in position in cement mortar 1:3 (1cement:3 coarse sand), cost ofrequiredcentring,shuttering and curing complete 1:3:6 (1 cement : 3 coarse sand : 6 graded crushed stone aggregate 20 mm nominalsize) |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns etc. for mass concrete. |
| 14 | Centering and shuttering including strutting, propping etc. and removal of form for: Columns, pillars, piers, abutments, posts and struts. |
| 15 | Centering and shuttering including strutting, propping etc. and removal of form for: Lintel, beams, plinth beams, girders, bressumers and cantilevers. |
| 16 | Centering and shuttering including strutting, propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platforms. |
| 17 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. Layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead upto 50m and ift upto 1.5m |
| 18 | Wooden planking, tongued and grooved in flooring including fixing with iron screws complete: 12 mm thick Second class teak wood |
| 19 | Marble stone flooring with 18mm thick marble stone as per sample of marbleapproved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement:4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with:Udaipur green marble |
| 20 | 20mm Cement plaster of mix:1 : 4 ( 1 cement : 4 fine sand) |
| 21 | 15 mm cement plaster on the rough side of single or half brick wall of mix :1:4 (1 cement: 4 fine sand |
| 22 | 6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand) |
| 23 | Providing and applying white cement based putty of average thickness 1 mm ofapproved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 24 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two or more coats)over and including water thinnable priming coat with cement primer |
| 25 | French spirit polishing, Two or more coats on new works including a coat of wood filler . |
| 26 | Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm) |
| 27 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 28 | Providing and laying vitrified floor tiles in different sizes(thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. completeSize of tile 600X600 mm |
| 29 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab of all colour and texture except Black, Cherry/Ruby Red. |
| 30 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Second class kail woo |
| 31 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws |
| 32 | Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Casement cum fixed panel window having both end single casement panel, middle fixed panels and at top completely fixed ventilator with S.S friction hinges (350 x 19 x 1.9) made of (big series) frame 67 x 60 mm , sash 67 x 80 mm &mullion 67 x 80 mm all having wall thickness of 2.3 ± 0.2 mm and single glazing bead/double glazing bead of appropriate dimension. (Area of window above 3.00 sqm upto 5.00 sqm). |
| 33 | Providing and fixing DGU of 20mm thick comprises of 5mm glass thick -10mm spacer 5mm thick glass is filled with argon gas between the two layer of glassThe glass is further finished on the side and is ready for installation type of glass is toughened and 90% transparency of saint gobbin/asahi india glass make as approved by engineer in charge. |
| 34 | Providing and fixing ISI marked oxidized M.S. tower bolt black finish, (Barrel type) with necessary screws etc complete. 150x10 mm |
| 35 | Providing and fixing ISI marked oxidized M.S. handles conforming to IS : 4992 with necessary screws etc. complete : 125 mm |
| 36 | Providing and fixing ISI marked oxidized M.S. sliding door bolts with nuts and screws etc. complete : 300x16 mm |
| 37 | Providing and laying roof insulation with 40 mm thick impervious sprayed, closed cell free Rigid Polyurethane foam over deck insulation conforming to IS – 12432 Pt. III (density of foam being 40-45 kg/cum), over a coat of olyurethane primer applied @ 6-8 sqm per liter, laying 400 G polythene sheet over PUF spray andrough finish, in panels of 2.5 m x 2.5 m and embedding with 24 G wire netting and sealing the joints with polyolymerized mastic, all complete as per direction of Engineer-in Charge. |
| 38 | CARRIAGE OF MATERIALS ( MECHANICAL TRANSPORT) Cement & Steel….............190 km |
| 39 | CARRIAGE OF MATERIALS ( MECHANICAL TRANSPORT) Sand…..............15 km |
| 40 | CARRIAGE OF MATERIALS ( MECHANICAL TRANSPORT) Stone aggregate…..............15 km |
| 41 | CARRIAGE OF MATERIALS ( MECHANICAL TRANSPORT) Stone …................ 10km |
| 42 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid. |
| 43 | Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. 18. White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 44 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer of approved make Cera,Somani,Hindware |
| 45 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink drain board510x1040 mm bowl depth 250mm |
| 46 | Providing and fixing CP Brass telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia |
| 47 | Providing and fixing of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing .Rectangular shape 453x357 mm |
| 48 | Providing and fixing toilet paper holder.C.P. brass |
| 49 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge.Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc. PN-16 pipe , 25mm OD(SDR-7.4) |
| 50 | PN-16 pipe , 32mm OD(SDR-7.4) |
| 51 | Providing and fixing C.P.brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15mm nominal bore. |
| 52 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fitting and the base support for tank (Sintex, Electroplast, Star, Lotus or equivalent having valid ISI license). |
| 53 | Providing and fixing CP jali trap of approved make |
| 54 | Providing and fixing material for insulation of pipe with nitrile tube, tapping with cello tape for inner wall fitting complete job incl. carriage 19mm thick , 50 mm dia (OD) (PPR 25mm) |
| 55 | Providing and fixing material for insulation of pipe with nitrile tube, tapping with cello tape ,Rock wool 6 inch each side , wire mesh ,polythene, tapping with cello tape aluminium sheet 26 gauge cladding with diameter complete job incl. carriage 19mm thick , 50 mm dia (OD) (PPR 32mm) |
| 56 | Providing and fixing material for insulation of water storage tank with nitrile tube, tapping with cello tape Rock wool 6 inch each side , wire mesh ,polythene, tapping with cello tape aluminium sheet 26 gauge cladding with diameter complete job. 19mm thick nitrile sheet. |
| 57 | Providing and fixing heat tape 33 watt on PPR made of denforced or chlomelox on equivalent make as approved by engg in charge. Completed job |
| 58 | Supplying and fixing C.I. cover for manholes: 455x610mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg. |
| 59 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipesconforming to IS : 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm |
| 60 | 75 mm |
| 61 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS :5382, leaving 10 mm gap for thermal expansion.Bend 87.5° 75 mm bend |
| 62 | 110 mm bend |
| 63 | Providing and fixing 15mm nominal bore CP brass angle valve for basin mixer and geyser point of approved make conforming to IS 8931 of make Cera,Somany,Hindware |
| 64 | Providing and fixing Towel rail C.P.brass 600x2mm together with a pair of C.P. brass brackets to fit the size of towel rail |
| 65 | Providing and fixing PPR Unions PPR Union 25mm |
| 66 | Providing and fixing PPR Unions PPR Union 32mm |
| 67 | Providing and fixing geyser of required capacity of approved make all complete as per direction of the Engineer in-charge. 25 Litres |
| 68 | Providing and fixing ball valve (PPR) of approved quality complete.15 mm nominal bore |
| 69 | 20 mm nominal size |
| 70 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet:100 mm diameter |
| 71 | Providing and fixing uplasticised PVC connection pipe with brass unions : 15 mm nominal bore |
| 72 | Providing and fixing 8mm dia C.P./S.S. Jet with flexible tube upto 1 metre longwith S.S.triangular plate to Eureopean type W.C.of quality and make as approved by Engineer - in - charge |
| 73 | Providing and fixing PTMT soap Dish Holder having lengthof 138mm, breadth 102mm,height of 75mm with concealed fitting arrangements weighing notless than 106 gms. |
