Tender For B/R Repair/Maintenance Of Mes Installation Under Ge Gwalior.; 1 Taking down existing tarfelt from inaccessible roof and removing from site all as directed. Note: Removed material through out of MoD Land rate included above item. 2 Demolition of cement concrete of any description and in any position (un-reinforced) in ground floors and paving not exceeding 15cm thick (below or above GL) complete all as specified and directed. Note: Demolished material through out of MoD Land rate included above item. 3 M&L for cement concrete (1:2:4) type B-0, using12.5 mm graded stone aggregate in as in inaccessible roof,levelling course/mass concrete, padding finish even and smooth etc complete mixed with water proofing compound complete all as specified and as directed by Engr-in-charge. Note : water proofing compound shall be measured and paid separately under appropriate item of BOQ as supply only. 4 M&L for cutting grooves in brick /concrete wall, 75mm wide and 65mm deep and shaping horizontal face of groove with CM 1:3 complete all as specified and as directed. 5 M&L for PCC type B-1 (1:2:4) using 20mm graded stone aggregate as in coping, in lintels upto1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete all as specified and directed by Engineer in charge. 6 M&L for applying Smartcare Damp proof, a fibre reinforced elastomeric liquid water proofing membrane formulated with reinforcing acrylic fibers having Sun Reflectivity Index (SRI) of 105 on horizontal/vertical surfaces of roof/wall/chajjas in multiple coats @2.0 litre/sqm. Primary coat is self-priming coat of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1, damp proof: water) and other coats to be applied undiluted. (ii) The undiluted 2nd & 3rd coatings needs to be reinforced with 40 GSM geotextile to be sandwiched between them. (iii) After that final 4th coating shall be applied.The application shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes complete in all respect as per the direction of Engineer-in-Charge.Notes:-(a) The work shall be executed through authorised applicator of manufacturer only.(b) Authrised Applicator shall be approved by GE before starting of work.(c) All materials shall be procured directly form manufacturer.(d) The contractor shall furnish a written guarantee for the effectiveness of the water proofing treatment for a period of Ten Years in favour of GE. 7 Supply only Liquid water proofing compound @ 200ml per bag of cement. 8 M&L for PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges finished even and smooth complete all as specified and as directed by Engr-in-charge. 9 Dismantiling of stone slabs and tiles (Kota stone etc.)of any description or any thickness in floors, aprons, skirting, dado etc.laid bedded and pointed in any mortar complete all as specified and directed. 10 Dismantling floor, hearth or wall tilingof any description and in any positionincluding cement mortarbedding (but not backing) complete all as specified and directed. 11 M&L for machine cut Kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing, over and including screed bed or bedding layer of mortar 20 mm thick in cement mortar (1:6) complete all as specified and directed. 12 M&L for machine cut kota stone slab 20 - 25 mm thick as in riser / steps, skirting, dado,cills and pillars laid and jointed with grey cement slurry mixed with pigment to match with the shade of the slab including rubbing and polishing over and including 10 mm thick backing coatin CM (1:4) complete all as specified and directed. 13 M&L for non skid ceramic tiles, joint free, coloured tiles7mm to 8 mm thick (Square or rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and including 15 mm thick cement screed in (1:6) CM set and jointed in neat cement slurryand pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed. 14 M&L for non skid ceramic tiles, joint free, coloured tiles 7mm to 8 mmmm thick as in skirtingfixed over and including 10 mm thick cement screed in(1:4) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.with the colour of tiles complete all as specified and directed. 15 M&L for glazed ceramic tiles, coloured tiles 300mm x 450mm x 7 to 8 mm thickon vertical faces ie. as in skirting/dado etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles fix over and including 10 mm thick backing coat in cement mortar (1:4)completeall as specified and directed. 16 Dismantling of AC (corrugated / semi-corrugated) sheets in roof covering including any type of ridges complete all as specified and as directed. 17 S&F Pre painted galvalum corrugated steel sheet 0.50 mm thick having aluminum zinc coating 150 gsm/sqm of any colour having tensile strength of 550 Mpa as in Roof covering/cladding to wall fixed with self tapping screws complete all as directed by Engineer-in-charge. 18 S&F Pre painted galvalume plain steel sheet 0.50 mm thick having aluminum zinc coating 150 gsm/sqm of any colour having tensile strength of 550 Mpa as in Roof covering/cladding (ridge) to wall fixed with self tapping screws complete all as directed by Engineer-in-charge. 19 Excavation in post holes (or similar holes)each not exc 0.5 cum, getting out, in soft/loose soil including returning, filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25 cm, watering and removing surplus soil to a distance n.exc 50m and making good surfaces complete all as specified and directed. 20 S&F of Steel work in tubular trusses curved or plain i.e, truss bottom, top bend, sides, side supports, holding plates, posts and base plates etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240 complete all as specified and as directed. 21 M&L for plain cement concrete (1:3:6) type C2 using 40 mm graded stone aggregate in foundation filling and mass concrete complete all as specified and directed. 22 MS flats for supports or stays for chain link fencing and in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay),heavy,for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securingpurlinstowood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed complete all as specified and as directed. 23 Supply only Chain link fencing incl line wire any mesh, size and type to any standarards, rails straining bolts ect incl provn of binding wire complete all as specified and directed. 24 Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails straining bolts, etc including provision of binding wire complete all as specified and directed. 25 S&F, mild steel screw bolts (machine made) exceeding 5cm and not exceeding 10cm long withhexagonal or square heads at one end and screwed the other fitted with washer and one hexagonal or square nut complete all as specified and directed. 26 S&F galvanised, 2 strand, steel barbed wire, 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of strandard rails straining bolts, including securing and tying at crossing with and provisioning of galvanised mild steel wire, staples or steel pins, etc.complete all as specified and directed. Note: Each line wire shall be measured for payment 27 M&L for mild steel Round bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and welding with with flats of chain link fencing Fe-410 W (Gde E-250) quality-A or Fe-290 (Gde E-165) complete all as specified. 28 M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed. 29 S&F for framed work such as grills, gratings, etc, with ends of bars shouldered and or riveted , or forged into spikes, framed guard bars , barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 290,E-165 , complete all as specified and directed. 30 Demolition of brick work /stone work built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed. 31 M&L for Brick work with sub class B bricks straight or curved on plan exc. 6m mean radius built in cement mortar (1:6) complete all as specified and as directed. 32 Taking down cement on brick or stone walls etc including raking out joints, hacking for key scrubbing down with water etc complete all as specified and directed. Note: Demolished material through out of MoD Land rate included above item. 33 M&L for 15 mm thick rendering in CM 1:6 on fair faces of brick/ concrete/ stone surfaces finished even and smooth without using extra cement complete all as specified and directed. 34 M&L for rendering 15mm thick in cement mortar 1:4 on stone masonry surfaces, mixed with water proofing compoundat the rate of 200ml per bag of cement finished even and smooth without using extra cementcomplete all as specified and directed. Note : (i) The quoted rate is inclusive of necessary scaffolding works. (ii) WPC shall be measured and paid under relevant item. 35 M&L for 5 mm thick rendering in ceiling in CM 1:3 on fair faces of brick/ concrete/ stone surfaces finished even and smooth without using extra cement complete all as specified and directed. 36 M&L for preparation of new plastered surfaces of wall and applyingtwo coats of cement base paint over a coat of primer complete all as specified and directed. 37 M&L for preparation of new plastered surfaces of wall and applyingthree coats of white wash complete all as specified and directed. 38 M&L for preparation of new plastered surfaces of ceiling and applyingtwo coats of white wash complete all as specified and directed. 39 M&L for complete removal of existing treatment of plastered or unplastered surfaces walls andapplying two coat of white wash complete all as specified and directed by Engineer -in-Charge. 40 M&L for complete removal of existing treatment of surfaces of ceiling of plastered or unplastered surfaces and applying three coat of white wash complete all as specified and directed by Engineer -in-Charge. 41 M&L for complete removal of existing treatmentof surfaces of walls of plastered or unplastered surfacesandapplying two coat of cement base paint complete all as specified and directed by Engineer -in-Charge. 42 Taking up or down steel tubing and connections including cleaning for refixing or removing to store of 15mm bore of pipe, complete all as specified. 43 Taking up or down steel tubing and connections including cleaning for refixing or removing to store of 20mm bore of pipe, complete all as specified. 44 Taking up or down steel tubing and connections including cleaning for refixing or removing to store of 25/ 32mm bore of pipe, complete all as specified. 45 Supply and laying 20mm dia of bore CPVC pipe SDR-11 and plain CPVC SDR-11 fittings (ISI) marked, concealed or fixed to wall or laid in floors complete all as specified. 46 Supply and laying 25mm dia of bore CPVC pipe SDR-11 and plain CPVC SDR-11 fittings (ISI) marked, concealed or fixed to wall or laid in floors complete all as specified. 47 Supply and laying 32mm dia of bore CPVC pipe SDR-11 and plain CPVC SDR-11 fittings (ISI) marked, concealed or fixed to wall or laid in floors complete all as specified. 48 S&F 20mm dia steel tubing and connection galvanised with all fittings medium grade tube in floors, walls, roof and ceilings etc complete. 49 S&F 25mm dia steel tubing and connection galvanised with all fittings medium grade tube in floors, walls, roof and ceilings etc complete. 50 Dismantling of water tanks exc 250 ltr and n.exc 500 ltr capacity and removing from site complete all as specified and as directed. 51 Dismantling of water tanks exc 500 ltr and n.exc 1000 ltr capacity and removing from site complete all as specified and as directed. 52 S&F Rotational moulded polyethylene multilayer water storage tanks (cylinderical vertical with closed top) 500 litres capacity, triple layer in construction white in colour hoisted and fixed in position complete all as specified and as directed by Engr-in-Charge. 53 S&F Rotational moulded polyethylene multilayer water storage tanks (cylinderical vertical with closed top) 1000 litres capacity, triple layer in construction white in colour hoisted and fixed in position complete all as specified and as directed by Engr-in-Charge. 54 S&F for 20mm ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed in 20mm dia pipe. (Minimum weight 15mm-142gms, 20mm-210gms, 25mm-455gms, 40mm-690gms) complete all as specified and directed. 55 Disconnecting existing water tanks, setting aside (or lowering if required) for repairs, Cleaning etc and reconnecting and refixing in position capacity exc 250 liters and n. exc.500 litres complete, all as specified and directed (cleaning, repairing etc measured separately) 56 Disconnecting existing water tanks, setting aside (or lowering if required) for repairs, Cleaning etc and reconnecting and refixing in position capacity exc 500 liters and n. exc.1000 litres complete, all as specified and directed (cleaning, repairing etc measured separately) 57 Cleaning and removing all scale and dirt etc. from tanks and from mouths of circulating pipes etc capacity of tank exc 250 ltrs but n.exc 500 ltrs complete all as specified and as directed. 58 Cleaning and removing all scale and dirt etc. from tanks and from mouths of circulating pipes etc capacity of tank exc 500 ltrs but n.exc 1000 ltrs complete all as specified and as directed. 59 S&F in repair 20mm ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed in 20mm dia pipe. (Minimum weight 15mm-142gms, 20mm-210gms, 25mm-455gms, 40mm-690gms) complete all as specified and directed. 60 S&F for in repair gun metal globe/gate valve with iron wheel head screwed both ends for iron pipe of 20mm bore complete all as specified and directed. 61 Taking down eaves gutters and rain water pipes (any size 75mm to 110mm of any pattern) of any description and in any position including all fittings, heads, shoes, bend, swan necks etc (measured overall as fixed along the centre line over fittings and accessories) complete all as specified 62 S&F for 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified 63 S&F for 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified 64 S&F for 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified 65 S&F for 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified 66 S&F for 110mm dia PVC (SWR) pipe bends any radious complete all as specified and directed. 67 S&F for 75mm dia PVC (SWR) pipe bends any radious complete all as specified and directed. 68 S&F for 110mm dia PVC (SWR) pipes junction single (single T/Y) equal or unequal any radious with access door complete all as specified. 69 S&F for SWR bends 75mm provided with access door complete all as specified. 70 S&F for 110mm dia PVC (SWR) vent cowl complete all as specified. 71 S&F Stack clamps made out of50 mm by 5 mm flat iron and 16 mm dia around iron stays including boltand nuts for securingends of stays to walls or roofs, bore pipe 100 mm dia pipe complete all as directed. 72 S&F Stack clamps made out of50 mm by 5 mm flat iron and 16 mm dia around iron stays including boltand nuts for securingends of stays to walls or roofs, bore pipe 75 mm dia pipe complete all as directed. 73 M&L for PVC (SWR) gully trap 125 /100plain with gratingincluding jointing with solvent cement as in repair, complete all as specified and directed. 74 S&F for in repairs mild steel Chromium plated grating 100 mm dia, fixed in repairs to Nahani traps, complete all as specified and directed. 75 S&F in repairs for vitreous china squatting pan, orissa pattern sise 580x440mm white with integral foot rest (excluding flushing cistern) including vitreous china ‘P’ or ‘S’ traps and connection to trap and to flushing pipe to complete and making good to floor, complete all as specified and directed. 76 S&F for in repair PVC valveless syphonic action type flushing cistern low level white with inlet ball valve,float end handle handle including bracket complete of capacity 10 litres, complete all as specified and directed. 77 Supply only15mm dia PVC connection with PTMT nuts of length 450 mm, complete all as specified and directed. 78 S&F for in repairsofvitreous china wash basin, white, flat back, size 550 x 400mm Including waste coupling ,waste pipe and labour for fixing pillar tap ,pvc connection but including cutting for and pinning in ends of and including brackets complete all as specified and directed. . Note : Pillar tap andPVC connection will be measured paid separetly. 79 S&F for in repairs PVC waste pipe flexible type 32mm bore, complete all as specified and directed. 80 S&F for in repairswaste couplingfittings , brass chromium plated for glazed ware sinks ,basins ,etc.with long screwed shanks and fly nuts ,flange end bedded in red lead cement and other fixed 32 mm dia bore complete all as specified. 81 S&F for in repairsvitreous china urinals, Half stall type ,whitewith grating and union for discharge pipecomplete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete all as specified and directed. 82 S&F for in repairs for 15 mm Stop valve cast copper alloy screwed down high pressure with CAPSTON HEAD handle chromium plated with long shank and cup (concealed type) screwed both ends for iron pipe 15mm bore or for unionscomplete all as specified and directed. 83 S&F for in repairs15mm,pillar taps fancy type long body chromium plated,cast copper alloy, with capston heads,scewed down high pressure, with or without lettered hot or Cold with long srewed shanks and flynuts, srewedfor iron pipe complete all as specified . 84 S&F for in repairs 15mm angle cock chromium plated,cast copper alloy, with capston heads,scewed down high pressure, with or without lettered hot or Cold with long srewed shanks and flynuts, srewedfor iron pipe fixed and complete all as specified . 85 S&F for in repairs for 15mm, bib tapFancy type long body chromium plated,cast copper alloy, with capston heads,scewed down high pressure, with or without lettered hot or Cold with long srewed shanks and flynuts, srewedfor iron pipe complete all as specified 86 S&F in repair Aluminium anodised tubular towel rail 20mm dia complete all as specified and directed. 87 S&F in repairs for shower rose brass chromium plated without swivel joints, 100 mm in size including fixing to steel pipe complete all as specified and directed fixedin repairs, complete all as specified and directed. 88 S&F for in repairs600x450 mmlooking mirror of selected quality glass mounted on 4mm thick AC building board or commercial plywood and fixed to wooden plug with chromiun plated screws complete all as specified and directed 89 Dismantling of reinforced cement concrete of roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed. Note: Removed material through out of MoD Land rate included above item. 90 M&L for applying bonding agent for bonding old to new concrete surface likes chajja/ beam/ceiling/facia etc by high performance modified Styene- Butadiene Rubber (SSR) base binder. Applying of binder is as 10 Sqm/ per lits etc complete all as specified & directed. 91 M&L for applying 25 mm thick (average) repair mortar ready to use single component polymer modified repair mortar for repair of RCC members likes beams, columns, chajja and facia/ ceiling, mortar having good compressive strength and shrikage resistance etc complete all as specified & directed. 92 Taking down chowkhat or frame (without taking off shutter from the frame)not exceeding 1.5 Square metre each complete all as specified and as directed. 93 Taking down chowkhat or frame (without taking off shutter from the frame) exceeding 1.5 sqm and not exc 4.00 sqm each complete all as specified and as directed. 94 Supply & Fixing solid PVC door frame of size50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube fixed in opening as per specification & drawings complete all as specified and as directed. 95 S &F for factory made solid panel PVC door shutter 30mm thick (style) consisting to framemade out ofM.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVCCchannel having a PVC sheet strip of 20 mmwidth struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Penelling of plain colour PVC sheet to be fitted in the MS. frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. complete all as specified and as directed. 96 S&F pressed steel frame 105mmx60mm for doors with one or more rebates including S&F of necessarylungs and hinges(min 100mm size), lock strike plate,etc as per IS requirementcomplete all as specified and directed 97 S&F 30mm thick Flush shutters, soild coreconstruction, with paticle board core and plywood face panels, commercial type complete all as specified and directed. 98 S & F of windows made of pre-painted steel (Base steel as per IS-513 of 0.58mm minimum thick D Quality galvanized as per IS-277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted as a polyster paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 52 x 25mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars / grills fly mesh shutter section should be of 20-40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap, Elixir or equivalent stay, handles 2 Nos of heavy-duty stainless steel pivot hinges be provided per shutter. The windows should be paneled with 4 mm thick plain float glass and SS mesh for fly mesh shutter (304 grade). Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/ masonry wall by means of self-expanding, screws including 10mm sqaure guard bars with 6 (152.4mm) pitch etc complete all as specified and directed. 99 S & F of ventilators made of pre-painted steel (Base steel as per IS-513 of 0.58 mm minimum thick D Quality galvanized as per IS-277 with Zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 48x50mm, centre mullion should be of 48x50mm, section for shutter should be of 52x 25mm and rebate for Glazed shutter with a 20mm provision for Guard bars/Grills. The sections are to be cut to length mitre joined with corner bracket. Centre mullion is to be fixed with mullion cap. Handle, stay, 2 Nos of Stainless Steel heavy duty Pivot hinges shall be provided per shutter the windows fitted with 4mm thick plain float glass with rubber gaskets including fixing the frames in concrete/ masonry wall by means of self expanding screws, Including fixed panel beading section should be of 12x12mm. Outer frame mullions to have 10mm Square guard bars with 6 (152.4mm) pitch etc, complete all as specified & directed. 100 S&F of 4mm thick sheet glass ordinary quality and and glazing with oil putty, silicon or S wooden beads, in squre n exc 0.5 sqm in each pane including hacking out aid broken glass of any thickness and any description from wooden/steel frame/stone concrete or block surrounds complete all as specified and directed 101 S&F of 4mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane with oil putty, silicon or S wooden beads, including hacking out old broken glass of any thickness and any description from wooden/steel frame/stone concrete or block surrounds complete all as specified and directed 102 S&F, aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 300 mm and fixed complete all as specified and directed. 103 S&F in repairs Aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed. 104 S&F for aluminium butt hinges of 100mm type C-21 complete all as specified 105 S&F for Mild Steel Butt hinges , medium weight, cold rolled , of size 100 mm complete all as specified. 106 S&F in repairs butt hinges 100mm long medium weight, cold rolled mild steel complete all as specified and directed. 107 S&F for MS 300 mm ordinary rat tail springs plate type incl.rollar plate etc, complete all as specified and directed. 108 S&F for Extruded aluminium alloy handle of 150 mm size fabricatedtype, anodised complete all as specified. 109 S&F in repairs aluminum handles cast type, anodized of 150 mm size complete all as specified and directed. 110 S&F for aluminium anodised barrel tower bolt of 200mmof extruded section complete all as specified. 111 S &F in repairs 200mm long aluminium anodised, barrel tower bolt of extruded section and fixed complete all as specified and directed. 112 S&F in repair galvanised wire cloth,0.56mm nominal dia ofwire and averagewidth of aperture 1.18mm and fixed with tinned tacks or galvanisedstaples complete all as specified and directed. 113 S&F for Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, Overall length of cover plate 150 mm, fixed to shutters complete all as specified and as directed. 114 Refixing including taking down and easing and adjusting in same opening of wooden/ aluminium/pvc, door/window shutter exceeding 1 Sqm and not exceeding 2 sqm for easy operation, tightning hinges, adjusting position of hinges, tower bolts, sliding bolts, glazing clips rubber neoprene packing etc including provision of necessary screws. 115 Refixing including taking down and easing and adjusting in same opening of wooden/ aluminium/pvc, door/window shutter exceeding 2 Sqm for easy operation, tightning hinges, adjusting position of hinges, tower bolts, sliding bolts, glazing clips rubber neoprene packing etc including provision of necessary screws. 116 Taking down unserviceable steel rolling shutter of any type of area exceeding 4 sqm and not exceeding 10 sqm incl hood cover, sliding railing, ball bearing, safety lever locks etc complete fittings and fixtures complete all as specified and as directed. 117 S&F of Steel rolling shutters, thickenss of lath 1.25mm with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete:push pull or manual type including Ball bearing for rolling shutters and also including Safety lever locks mild steel with 4 levers forrolling shutterscomplete all as specified and as directed. 118 S&F of Ball bearing for rolling shutters complete all as specified and as directed. 119 S&F of Safety lever locks mild steel with 4 levers forrolling shutterscomplete all as specified and as directed. 120 M&L for 75mm thick PCC (1:3:6) Type C2using 40mm graded stone aggregate as in plinth protection surface even and fair without using extra cement complete all as specified and as diected. 121 M&L for Forming Construction joint 30mm deepx10mm wide filled with sealing compound grade A complete all as specified and as diected. 122 M & L PCC (1:2:4) Type B1, 75 mm thickusing 40 mm graded stone aggregate asfloor surfaces concrete complete all as specified and directed. 123 M&L for sand filling under floors or in foundations including watering andconsolidation completeall as specified and directed . 124 Material and labour for machine made ,1st quality, precastcement concrete rubber moulded coloured interlockingpaver blocks / tiles , 60mm thick of grade M-35,of any shapeor shap and designe as approved, with grey cement and colour pigment , laid over sand cusionfixedas in floors/ paths/ pavings etc,complete all as specified and directed. Note : Sand Cusion shall be measured and paid in separate item 125 M&L for chequered cement concrete tiles of size 20cmx20cmx25 mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry over and including 20 mm thick screed bed in cm (1:6) complete all as specified and directed. 126 M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius inhalf brick thick walls built in cement mortar (1:4).complete all as specified and as directed.
