Tender For Certain B/R And E/M Repair In Various Units At Gulpur, Sekhlu And Natu In The Aor Of Age B/R-Ii Under Ge 881 Ews.; 1 Demolition of cement concrete (unreinforced) on ground floor or paving not exc 15 cm thickness (below or above ground level), complete all as specified and directed. 2 M&L for rendering 10 mm thick in CM 1:3 on fair faces of brick work or concrete surfaces,mixed with liquid water proofing compound as per manufacturers instructions, finished even & smooth without using extra cement, complete all as specified and directed. 3 M&L for cement concrete 1:5:10 in foundations filling and mass concrete as in sunken floor etc complete all as specified and directed. 4 M&L for applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu m/per sqm, complete all as specified and directed. 5 M&L for polythene film, 150 micron thick, laid on a coat of bitumen primer 0.30 to 0.50 kg per sqm, complete all as specified and directed. 6 M&L for 75 mm thick PCC 1:4:8 type C-2 (using 40mm graded crushed stone aggregate) as in sub base to flooring/path etc. finished the surface even & fair, complete all as specified and directed. 7 M&L for 25mm thick PCC (1:2:4) type B-1 with (using 20 mm graded crushed stone aggregates) as in sub base of flooring, finished even and rough to receive the top layers, complete all as specified and directed. 8 S&F in repair for 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed. 9 S&F in repair 75mm bore PVC (SWR) bends any radius fixed in floor, complete all as specified and directed. 10 S&F in repair 75mm bore PVC (SWR) junction single, (Single T) equal or unequal, complete all as specified and directed. 11 S&F in repair 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified and directed. 12 S&F in repair 40mm bore Low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq. cm laid in floor/sunken floor including cutting hole and grouting complete all as specified and directed. 13 S&F in repair 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall with GI/Alu clamps fixed, complete all as specified and directed. 14 S&F in repair 110 mm bore PVC (SWR) bends any radius fixed complete all as specified and directed. 15 S&F in repair 110mm bore PVC (SWR) vent cowl, complete all as specified and directed. 16 S&F in repair Vitreous china premium/ 1st quality wash down water closet floor mounted EWC white/ ivory/off white (closed pattern incl all necessary accessories like rug bolts/ gel gasket etc including built in flushing cistern of 10 ltrs capacity, soft closing seat cover, PVC outlet pipe and necessary solvent etc complete all as specified and directed. 17 S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding flushing cistern pipe) including fixing bolts, flushing pipe etc complete all as specified and directed. 18 S&F in repair vitreous china squatting pan (Orissa pattern) size 580 x 440 mm, snow white, with P or S trap, front or back inlet and integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe and syphonage pipe etc. including lime concrete bedding, complete all as specified and directed. 19 S&F in repair PVC valve less symphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC. flush pipe for low level cistern including all joints, complete all as specified and directed. 20 S&F in repair PVC connections 15mm size with brass nuts of length 600mm, complete all as specified and directed. 21 S&F in repair Vitreous china wash basin, white flat back, size 550 x 400 mm excl taps, wastechain and plug and porcelain stopper but incl brackets, waste pipe & CP waste coupling,complete all as specified and as directed. 22 S&F in repair Vitreous China Pedestal for wash hand basin, complete all as specified and directed 23 S&F in repair PVC cabinet mirror of size 600x360mm, complete all as specified and directed. Make : Prayag, Plantex, Aquavive, Bath Queen 24 S&F in repair Fiber glass wash room corners set of three pieces of size 220mm, 175mm and 125mm fixed to wall, complete all as specified and directed. Make : Plantex, Prayag, Bath Queen 25 S&F in repair 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated screws and cup washers, complete all as specified and as directed. 26 S&F Bevelled edge mirror of selected quality glass with 2nd Class Hard Wood Beading of size 25x 10mmfixed to wall with the help of SS Screw including drilling holes etc complete all as specified and directed. 27 S&F in repair for Aluminium anodised tubular towel rail 20 mm dia, D type 60 cm long between flange, complete all as specified and directed.. 28 S&F in repair 15mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type long body screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly-nuts,screwed for iron pipe and fixed in repair all as specified and directed. 29 S&F in repair bib tap 15 mm bore, Brass CP (long shank), fancy type with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule, complete all as specified and directed. 30 S&F in repair bib tap 15 mm bore, two in one,brass CP, fancy type (long shank). with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed in repair complete all as specified. 31 S&F in repair 15mm bore Brass CP mixer for mixing hot & cold water screwed down for iron pipe and complete all as specified and directed. 32 S&F in repair stop valve fancy type cast copper alloy 15 mm dia, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handles, screwed both ends incl necessary fittings such as sockets for iron pipes or for unions, complete all as specified and directed. 33 S&F in repair telephonic hand shower (Health faucet) (ABS Body) MS chromium plated suitable forlongmm dia pipe with 1.25 mtr long flexible tube in chrome finish and ABS wall hook, complete all as specified and directed. 34 S&F in repair Chromium plated shower roses with or without swivel joints of size 200mm x 200mm, including Shower arm 15 mm size, 195mm long with bend of 45degree with flange and fixing to steel pipe or union, complete all as specified and directed. 35 M&L for Non skid joint free Ceramic tiles 7 to 8 mm thick (square/ rectangular) coloured/printed/ digital, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement over 15 mm thick cement screed bed in 1:4 , complete all as specified and directed. 36 M&L for glazed ceramic coloured/printed digital tiles, Premium quality of size 450x350x7 /350x250x 7 mm thick fixed as in vertical surfaces such as skirting, dados & repairs to step etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, fixed over and including 10mm thick plaster in CM (1:4) incl dismantling of tiles, complete all as specified and as directed. 37 S&F 25mm thick 2nd class hard wood planks, planed one side, with butt joints and fixed with SS nails supplied and fixed complete including one coat of hot bitumen primer on surfaces of planks dismantling of existing boarding, any description, fixed in any position with screw/nails all as specified and directed. 38 M&L for Second class hard-wood clean sawn timber framed in scantlings icluding fevicol as requiredvand one coat of hot blown bitumen primer on the surfaces and dismantling timber scantlings 40 sq. cm and over in section, in any position as in framed work, complete all as specified and directed. 39 M&L for Mild steel work as in hand rails, half round or other stock section or core for wooden hand -rail, straight portion drilled and countrsunk for ballusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screqing etc. wind ties for roof including securing bolts, posts and struts in fencing including cuttings, tops to shapes, as directed, drilling, holes, notching for wire etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting etc. fixed in repairs, and similar work conforming to Fe-250 Gde E-165, complete all as specified and directed. 40 S&F 20mm OD 3-layer PP-R polypropylene random co-polymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc including taking down of existing pipes of any description, complete all as specified and directed. 41 S&F 32mm OD 3-layer PP-R polypropylene random co-polymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc including taking down of existing pipes of any description, complete all as specified and directed. 42 S&F in repair 25mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe, complete all as specified and directed 43 Taking down chowkat or frame exc 1.5 sqm but n.exc 4 sqm with shutters (without taking taking off shutters from the frame). 44 S&F Solid PVC door frame of size 50 X 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube, supplied and fixed in repair in opening as per specifications and drawing complete all as specified and directed. 45 S&F Factory made solid panel PVC door shutters 30mm thick (style) consisting of frame made out of MS tube for top and bottom rail, MS frame shall be covered with heat moulded plain coloured PVC C channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail & bottom rail, Panelling of plain colur PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement, Supplied and Fixedin the frame at site as per specification and drawings complete all as specified and directed. 46 S&F 75mm butt hinges stainless steel, complete all as specified and directed. 47 S&F 150mm long aluminium anodised barrel tower bolts, complete all as specified and directed. 48 S&F 150mm size aluminium anodised door handles, complete all as specified and directed. 49 S&F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. 50 S&F Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, mortise lock, 5.5mm tinted glass/12 mm thick coloured PVC sheet, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed. 51 S&F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing ,anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (2 nos.) SS hinges, 100mm long (3 nos) suitable handle (1 no.) complete all as specified and directed. 52 S&F in repair Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aparture 1.18mm and fixed with tinned tacks or galvanised wire stapple in any types of door and windows, complete all as specified and directed. 53 S&F in repair 5.5mm thick tinted glass, fixed with existing snap beading, rubber gasket etc. area of each pane exc. 0.50 sqm fixed complete all as specified and as directed. 54 S&F Anodised aluminium frame and shuters for sliding doors/windows/ ventilators with one or more rebates including joining cleat for fixing, locks, rollers etc complete all as specified and as directed. 55 S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows,ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including 12mm thick coloured PVC board/5.50mm thick tinted glass complete andnecessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge 56 S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, fixed in repair all complete as per requirement and direction of Engineer-in- charge. 57 S&F door closer hydraulically regulated, designation No-3 universal type, aluminium (extruded section body), suitable for door shutter of 851to 1000 mm in width and weight between61 to 80 Kg and fixed complete all as specified and directed. 58 S&F Floor door stopper 140mm long of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete fixed in repair all as specified and as directed. 59 S&F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty, complete all as specified and as directed. 60 M&L for vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed be in CM 1:6. complete all as specified and directed. 61 M&L for vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick cement plaster as in backing coatin CM 1:4 and dismantling of tiles, complete all as specified and directed. 62 M&L for vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed be in CM 1:6 and dismantling of tiles all as specified and directed. 63 M&L for vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm,in skirting/dados set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick cement plaster as in backing coat in CM 1:4 and dismantling of tiles all as specified and directed. 64 M&L for exposed metal frame ceiling 600x600mm with 4.00mm thick calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 605 mm x 605mm GI grid including 4mm dia GI wire of required length fixed in RCC Roof/Truss etc with 40x3mm size 60mm long GI flat and expansion hold fastern of minimum 12.50mm dia including dismantling of ceiling of any type, complete all as specified and directed. 65 S&F in repair 5-6mm thick hollow insulated PVC coloured wall panelling including lining and necessary cleats, screws, bedding etc complet all as specified and directed. 66 Dismantling plain/corrugated steel sheeting, any gauge, thickness, complete all as specified and as directed. 67 M&L for 0.63mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts, in roofs, walls etc. with grade of zinc coating 275., completeall as specified and directed. 68 M&L for 0.63mm Plain, black, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings fixed with L-type or J-type or cranked hook bolts, any gauge, thickness, including, complete all as specified and directed. 69 Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and directed. 70 M&L for prepartion of new surfaces on surfaces of any description and position and applying two coats of synthetic enamel paint on steel surface over a coat of red oxide primer, completeall as specified and directed. 71 M&L for rendering 15 mm thick in CM 1:6 on fair faces of brick work or concrete surfaces, finished even & smooth without using extra cement, complete all as specified and directed. 72 M&L for 15mm thick plaster of cement mortar (1:4) rendering on fair faces of brick work mixed with liquid water proofing compound as per manufacturer instructions finishing the surface even and smooth without using extra cement, complete all as specified and as directed. 73 M&L for preparing of surfaces and applying plaster of paris putty of 1 mm thickness over plastered surface and making it smooth, complete all as specified and directed 74 M&L for preparation of new plastered surfaces and applying two or more coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre of approved manufacturer of required shade and colour, complete all as specified and directed 75 M&L for preparation of old plastered surfaces and applying one or two coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre of approved manufacturer of required shade and colour, complete all as specified and directed 76 Material & Labour for preparation of new plastered surfaces and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces of walls complete all as specified and as directed. 77 Material & Labour for preparation of old plastered surfaces and applying one or two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over old surfaces of walls complete all as specified and as directed. 78 Taking down cement plaster on wall of any desription incl racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. 79 Demolition of brick work or stone/boulder masonry built in cement mortar incl all quoins, arches, pillars etc but excluding ashlars facings dressed stone work and Precast concrete articles, complete all as specified and directed. 80 M&L for brick work with sub class B bricks, straight or curved on plan exc 6 m mean radius, built in CM 1:6, complete all as specified and directed. 81 M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4, complete all as specified and directed. 82 M&L for 18-20mm thick granite (of approved type colour) work (table rubbed & polished) in jambs, pillars, window cills, cooking plateform laid over and including 20mm thick cement screed (1:4) and jointed with grey cement slurry and pointed with white cement (1:2) with admixture of pigment to match the colour of granite stone including cutting and and moulding the edges, complete all as specified and directed. 83 M&L for 18-20mm thick granite (of any type) machine cut, in skirting/dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone over 15mm thick cement plaster in CM 1:4 including backing coats complete all as specified and directed. 84 M&L for 2mm thick Linoleum, plain/printed colouredflooring, laid with approved adhessive in floors including stretching, cutting and fitting complete all as specified and directed 85 S&F in repair Stainless steel sink, 1.0 mm thick for kitchen or lab, with plug, waste pipe,waste coupling,washers, incl cantilever cast iron brackets, connecting union etc overall size 495 x 420 mm with bowl size 410 x 330 x 160 mm, complete all as specified and directed. 86 S&F in repair Kitchen utensils dish rack of 07 layers made of stainless steel of size 765mm length, 910mm ht and 250mm width fixed on wall with SS screws fixed, complete all as specified and directed. 87 S&F PVC door guard, gap filler for door bottom seal strip to reduce door dust and to protect from insects for wooden or aluminium or PVC doors etc complete all as specified and directed 88 S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. 89 S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. 90 E&M PORTION:-Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specifiecd and directed. 91 M&L for point wiring with two single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cableand one single core 1.5 Sqmm(nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable as earth continuity to common earth and connecting to earth dolly running in and including PVC casing & caping (ISI marked) of suitable size with PVC boards of appropriate sizes and all requisite accessories such as PVC elbow, Tee, collars, bends etc. with PVC terminals box & cover for mounting swtches, sockets, fan regulator etc for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following :- 92 One light/fan/bell point controlled by one way switch 6 Amp complete all as specified and directed. 93 One 3/5 pin socket outlet 6 amp on same board complete all as specified and directed. 94 One 3/5 pin socket outlet 6 amp independent board complete all as specified and directed. 95 All as per srl item No 91 here in before but for one 3 pin socket outlet 16/20 Amp independent with two single core 2.5 Sqmm size cable as phase & neutral and one single core 2.5 Sqmm as in continuous earth wire complete all as specified and directed. 96 S&F ceiling rose, 3 terminal, surface bakelite 65 mm x 50mm, PVC/poly carbonate, insulated body, complete all as specified and directed. 97 S&F switch piano flush type 6 Amp single pole one way, (ISI marked), complete all as specified and directed. 98 S&F switch piano bell push type 6 Amp single pole, (ISI marked), complete all as specified and directed. 99 S&F socket outlet2 in 1, 3 pin, 5 Amp flush type universal, complete all as specified and directed. 100 S&F Switch socket combination, 5 pin, 5 Amp flush type universal, complete all as specified and directed. 101 S&F Switch socket multipurpose combination 2 in 1, 5 pin, 5 and 15 Amp flush type universal, complete all as specified and directed. 102 S&F Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed. 103 S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. for 1200 / 1400mm sweep, complete all as specified and directed. 104 S&F call bell, ding dong type suitable for 230/240 volts, AC 50 Hz, complete all as specified and directed. 105 Supply and fixing in repair inverterLED batten 1x 20W, with square profile and polycarbonate channel, lithium iron battery with charging time of 8 to 10 hours and backup tile upto 04 hourswith driver, holder incl LED tube light connecting up with with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. 106 Supply and fixing in repair LED tube light fitting 2 feet, 10 watt 220 watt 220 volt AC decorative box type with driver and connecting up with three core with three core flexible copper conductor cable of suitable size complete. all as specified and directed. 107 Supply and fixing in repair LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. 108 Supply and fixing energy efficientLED light fitting 30 W, input voltage 110V to 280VAC, 50 Hz with ingress protection IP66, LM 80, standard luminaries with efficiency 100 lumen/watt with secondary optics, perfectly matched lenses, complying to IEC60598/IS10322, with auto shut down on high voltage, CRI>70,PF>0.95, with short circuit & reverse circuit protection against10kV high surges, minimum 25000 burning hours (life), operating temperature 1 to 50oC, rectangular shape with pressure die cast aluminium housing with weather proof gasket for lamp and driver compartment with system wattage of 45W=10%W, rated lumens, 120 degree view angle, constant current type driver having THD<10%, including all fixing arrangement like clamps, nuts, bolts, washers, 45W LED rod lamp (having PF>0.9, input voltage 90-300V, IP-66, LM80) with all accessories pre-wired and connecting with twin core twisted flexible copper conductor cable with all necessary staging, etc. including bracket complete all as specified and as directed. 109 Supply and fixing in repair inverterLED lamp, CDL 12 watt, B22 base, complete all as specified and directed. 110 S&F in repair single pole and neutral enclosure with a two pin and metal earth plug and socket complete with & incl one single pole MCB of 20 Amps complete all as specified and directed. 111 S&F in repair sheet metal enclosure for DBs, vertical TPN double door (IP43), 4 ways built in bus bars suitable for 415 volts, AC, 50 Hz and suitable for FP MCCB as incommer and out going SP/TP MCBscomplete all as specified and directed.Note:- MCBs shall be measured and paid separately. 112 S&F in repair sheet metal enclosure for DBs, SPN double door (IP43), 4 ways with 200 amps rated bus bar suitable for 240 volts, AC, 50 Hz, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed. 113 S&F in repair sheet metal enclosure for DBs, SPN double door (IP43), 8 ways with 200 amps rated bus bar suitable for 240 volts, AC, 50 Hz, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed. 114 S&F in repair sheet metal enclosure for DBs, SPN double door (IP43), 12 ways with 200 amps rated bus bar suitable for 240 volts, AC, 50 Hz, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed. 115 S&F in repairMCBTPN 20-63 amps current carrying capacity, 415 volts 10 KA B curve, ISI marked, incl connection and testing, complete all as specified and directed. 116 S&F in repairMCBSPN 40 amps 240 volts 10 KA B curve, finger proof terminal, bi-connect termination, label holder, 35 Sqmm terminal capacity, insulating sliding shutter large two position dolly, ISI marked, complete all as specified and directed. 117 S&F in repair MCBsingle pole 6 to 32 amps 240 volts 10 KA C series complete all as specified and directed. 118 S&F Switch socket combination, 5 in 1, 16/20 Amp incl box with 4 fixing holes, complete all as specified and directed. 119 S&F Switch socket combination, 5 in 1, 6 Amp incl box with 4 fixing holes, complete all as specified and directed. 120 S&F exhaust fan made up of sturdy engineering plastic body complete with louvers shutter, voltage 230 V, 50 Hz, 1200 RPM, copper winding of 300 mm sweep, including all connecting accessories, complete and taking out old existing exhaust fan, complete all as specified and directed. 121 S&F heavy duty metallic exhaust fan 300 mm sweep 1400 RPM, single phase 230 Volts including all connecting accessories, complete and taking out old existing exhaust fan, complete all as specified and directed. 122 S&F heavy duty metallic exhaust fan 450 mm sweep 1400 RPM, single phase 230 Volts including all connecting accessories, complete and taking out old existing exhaust fan, complete all as specified and directed. 123 S&F Earthing complete with galvanized steel earth plate electrode 60cmx 60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanized iron wire 4.0mm dia by means of bolts, nuts and washers of galvanized iron or steel, protected by GI light grade pipe 15mm bore including GI light grade water pipe 20mm dia with funnel all as shown in electric plate No. 3 of 2009 SSR Pt-I and testing complete including earth work in any type of soil, PCC 1:2:4 type B-1 as in earthing pit and cover 50mm thick reinforced with 6mm dia MS round bar @ 10cm C/C both way and MS frame, common salt, charcoal and testing on completion including dismantling unsv earthing whereever required, complete all as specified and directed. 124 S&F Sub main wiring with single core cable 2x 4 Sqmm FRLSinsulated unsheathed stranded copper conductor cable 1100 Volts grade including suitable size PVC casing cappingmedium grade ISI marked alongwith 1x 4 Sqmm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly, incl dismantling old wiring and making good the surface by plastering and 2 coats of existing paint/colour complete all as specified and directed.Note:-Three wire of 4 sqmm and one run of PVC conduit/casing caping shall be measured as one unit. 125 S&F Sub main wiring with single core cable 2x 6 Sqmm FRLSinsulated unsheathed stranded copper conductor cable 1100 Volts grade including suitable size PVC casing cappingmedium grade ISI marked alongwith 1x 6 Sqmm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly, incl dismantling old wiring and making good the surface by plastering and 2 coats of existing paint/colour complete all as specified and directed.Note:-Three wire of 6 sqmm and one run of PVC conduit/casing caping shall be measured as one unit. 126 Taking out old unsv ceiling fan from site of capacity 1200/1400 mm sweep and replacement withceiling fans complete with blades, down rods, and accessories, 230 V, 1200 mm sweep, min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)incl all connecting accessories complete all as specified and directed by Engineer-in-charge. 127 Supply and laying 1100 volts grade heavy duty cable PVC insulated solid aluminium conductor served with PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 m apart including 4mm dia GI suspension wire, one twin core cable flat or circular of size 10 Sqmm, 2 core& including taking down old old unsv service cable connection, complete all as specified and directed.
