Decorative Works For Bactrological Water Testing Laboratory Including Some Other Allied Works At Kalyaneswari Wtp Under Rcfa Part-I Water Supply Scheme.- 1 Room repairing Portion:- 2 Cleaing the store room by engaging manual labour, carrying old files, printer cartridge, miscelleneous materials from the room, shorting properly at present of office staff and stored properly in desk as per direction.(Near about total Forty labours are engaged) 3 Dismantling the old wooden framed window from existing place also stored into godown as per direction, this cost included with concrete cutting, removing , cleaning floor by using broom. 4 Anti-termite treatment to the junction of wood work and masonry walls with chemical emulsion by admixing chloropyrofos emulsifiable concentrates (1% concentration) with water by weight including spraying at the points of contact with the adjoiningmasonry by drilling 6m. dia holes at a downward angle of about 45 degree at the junction of woodwork and masonry and squirting chemical emulsion into these holes at the rate of half litre per hole. The entire work is to be carried out as per specification of Code I.S.-6313 (Part-III)-1981. The shutters are to be sprayed with emulsion. on both sides. All wooden fixtures like almirahs, racks etc. are also to be throughly sprayed with chemical emulsion.(Payment will be made on the basis of outside measurements of doors and windows) 5 Crazy marble stone flooring, including filling the gaps with light shade pigment with white cement marble powder mixture (3 parts of white cement : 1 part of marble powder) by weight in proportion of 4:7 (4 cement marble powder mix : 7 white, black or white and black marble chips of sizes from 1 mm to 4 mm nominal size by volume), with under layer 25 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size), including rubbing, polishing and cement slurry etc. complete: 15-18 mm thick crazy marble stone white, black or as specified. 6 Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium sections for the following units:-(A) Glazed aluminium sliding windows made of extruded and annodized alloy aluminium sectios, fabrications, including cutting to proper shape and size, drilling and aligning of window shutter frame fitted with in builtlocking arrangements, sliding rollers and other necessary fittings, fixture, adhesives and joineries along with extruded neoprine or EPDM gasketing in between window frame and masonry work (walls, column, beam.lintels etc.) as well as between glass and shutter frame for fixing glass and Polysulphide sealant and in between shutter and window frame where necessary including cutting to requisite size and fixing glass as per drawing, specification and direction of EIC. The rate includes the hire charge of all tools and plants, including all incidental charges, adhesive, joineries such as screw, cleat angle etc. but excluding the cost of extruded aluminium sections, glass, neoprene / EPDM gasket, locking arrangement and rollers.-Openable/ Casement window. 7 Grinding to marble / mosaic floor including remaining stone, if necessary, after cutting with manual labour / machine, where necessary. 8 Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick)Add extra for each additional floor over the rate for ground floor for the above item when used on External Surface, i) Upto 4th floor. 9 Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturers specification and as per direction of the EIC. (In Ground Floor)-(b) Two Coats-ii) Solvent based interior grade Acrylic Primer. 10 Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturers specification) including cleaning and smoothning of surface.Two Coats. 11 Providing and fixing of false ceiling with powder coated exposed G.I. grid suspension system (E-Grid U-1520 or equivalent load carrying capacity with mid span deflection not exceeding 1/360 span with hanger spacing of 1200mm c/c ) consisting of Main Runner 3600 mm long, Cross Tee 1200 mm / 600 mm long andWall Angle. The Wall Angle shall be fixed on PVC Dash Fasteners on the perimeter of the wall by steel screws with distance 300mm c/c. The Main Runners to be placed @ 1200 mm. The Cross Tee 1200mm will be inserted in the pre-cut slots of Main Runner at a regular interval of 600 mm to form a modular grid of 1200mm X 600mm. Additional Cross Tees of 600 mm shall be placed perpendicular to the Cross Tee 1200 mm long to finally form a grid of 600 mm X 600 mm. Grid of module size 600 mm X 600 mm shall be supported by 6 mm dia G.I. wire from purlins / soffit. 15mm thick OW Acoustic Board (Mineral Fiber Acoustic Ceiling Tiles) of approved patern and size 595mm X 595mm with NRC value > 0.65 should be placed in the Grid module to form a False Ceiling. Allcomplete as per the drawing & directions of Engineer-in-charge.In ground floor.a) Acoustic False Ceiling (with 15mm thick OW Acoustic Board and E-Grid U-1520). 12 Supplying, fitting and fixing boiling water resistant ply conforming to IS: 303-1989 bonded with phenol formaldehyde synthetic resin of approved make and brand fitted and fixed as per design as per approval and direction of Engineer-in-Charge.[excluding the cost of supporting frame work and teak wood batten/Lipping]In Ground Floor-vi) 19mm. 13 Supplying fitting, fixing decorative lamination conforming to IS: 2046 : 1995 as per approved make, brand, finish and thickness with fitting, fixing the same on Particle/MDF / Ply Boards with recommended / approved adhesive with proper clipping the sides for better attachment as per direction of Engineer-incharge.The rate includes the cost of labour, adhesive and all incidental charges thereof. In ground floor,Glossy/Matt/Suede excluding surface texture or metallic lustre.i) Thickness of laminate 1.5mm 14 b) Supplying, fitting fixing Godrej type hydraulic (oil check) floor door spring, heavy duty double action with brass shoe, brass top centre aluminium top cover etc. complete set as per direction of Engineer-in-charge. 15 Electrical wiring Portion:- 16 Supply of 12 Watt, Ultra slim recess-mounting round LED downlighter designed with excellent thermally managed aluminium pressure die-cast housing with heat-dissipatingfins for larger surface area finished in epoxy powder-coated white to deliver high-efficacy light output and uniformity, utilising edge-lit technology. Ultra slim surface-mounting square LED downlighter designed with excellent thermally managed aluminium pressure die-cast housing with heat-dissipating fins for larger surface area finished in epoxy powder-coated white to deliver high efficacy light output and uniformity, utilising edge-lit technology.(Make:-Orient/Other approved make) 17 Supply of 6 watt, LED, Nucleus Recess-mounting adjustable COB LED downlights made of extruded aluminium fins and high-lumen LED as a light source with clear diffuser and separate electronic driver.LED recessed adjustable downlight made up of high-grade aluminum die-cast housing with spectacular reflector with 36-degree beam angle. It is featured WALL-WASHER.(Make:-Orient/Other approved make) 18 Supply of 15 watt, LED, Nucleus Recess-mounting adjustable COB LED downlights made of extruded aluminium fins and high-lumen LED as a light source with clear diffuser and separate electronic driver.LED recessed adjustable downlight made up of high-grade aluminum die-cast housing with spectacular reflector with 36-degree beam angle. It is featured WALL-WASHER.(Make:-Orient/Other approved make) 19 Supply of LED profile light strip 45 Watt, 240 LEDs/mtr, no harmful UV/IR radiation, 5 mtr each length, with out driver.(Make:-Orient/Other approved make) 20 Supply of 3 Amp, 12 Volt, indoor constant voltage driver.(Make:-Orient/Other approved make) 21 Distribution wiring in 1.1 KV grade 2x22/0.3 (1.5 sqmm) single core stranded FR PVC insulated & unsheathed copper wire (Brand approved by EIC) in suitable size PVC casing-capping (Precision make) with 1x22/0.3 (1.5 sqmm) single core stranded FR PVC insulated & unsheathed copper wire for ECC, incl. necy. PVC clips, fittings etc. to light/fan/call bell point with piano key type switch (Anchor make) fixed on sheet steel fabricated switch board with Perspex/bakelite top cover on wall incl. necy. connections and making earthing attachment and mending good damages to building works [PVC casing-capping on surface and Switch boardconcealed]-Average run 6 mtr. 22 On Board-5A 3 pin flush type plug socket with piano key type switch. 23 Add GST @ 18% 24 Add CESS @ 1%
