Tender For Special Repair To Bldg No 09 (Adm Bldg) Of 1 Up Girls Bn Ncc Under Ge (East) Agra.; 1 Taking down existing roof treatment and all loose and de-bonded concrete/ screed, loose particles, dirt etc & Debris should be removed from Bldg, roof substrate must be pressure-washed with water with, a minimum working pressure of 1,400 psi is to be used to and/or remove all dirt, dust, chalking and waste products. Remove algae, mold by using bleach solution or biowash etc complete all as specified & directed. 2 M&L for repair of all visible hairline cracks on concrete roof / screed more than 0.50 mm and not giving hollow sound, should be cut and widen in V shape with mechanical cutter in the size (10mm W x 6mm D). Fill cracks withPU sealant / Hybrid Sealant with suitable gun and smoothed with a putty knife or trowel. Allow sealant to cure a minimum (72 Hrs.) 3 days etc complete all as specified & director. 3 M&L for remove loose and damaged concrete roof screed in pockets with mechanical cutter. Clean the concrete screed with high pressure water jet to remove dirt and loose particles. Brush apply a bond coat ofPidicrete URP mix in the ratio of 1:1 (URP 1: Cement 1) by volume to make it lump free slurry when applied on in the pre wet surface. Laid to fall roof screed in correct slope and gradient. Mix Dr. Fixit Pidicrete URP 10% by weight of cement in (M20) concrete in ratio of 1:1.5:3 i.e., one bag of 50kg cements: 1.5 times volume of sand: 3 times volume of aggregates: 25L water. Level the repair mortar and finish with trowel average 25mm thick. Moist cure should be done for 7days. Air cure screed for 7days, before application of roof top coat coating system etc complete all as specified & directed. 4 Apply one coat ofCipoxy 16D primer in the ratio 1:1 spreading at the rate of 0.200 kg-0.250 kg /sqm in complete dry condition where moisture contain below 7% (should be checked with moisture meter)Allow the primer coat to dry for 6 to 8 hours. Apply 1st coat ofRoofseal Classic without dilution spreading at the rate of 0.70/litre/Sq.mt/Coat until all surface is covered. Lay a 45 GSM Fibre glass mesh as a reinforcing material which is incorporated in the coating when the first coat is still in wet condition. Allow the first coat to dry for approximately 4 to 6 hours. Apply the second of chemical with the same application coverage, but in a direction perpendicular to that of the first and second coats. Allow each coat to air cure for a minimum of 4-6 hours after application. Check to see no void surface is left untreated / uncoated.Allow the system to air cure for 7 days minimum etc complete all as specified & directed. 5 Diasmantling bricks (laid flat or on edge) or brick tiles in floors, channels,kerbs, aprons, etc. (each layer) laid bedded and pointed in nay mortor complete all as specified and directed. 6 M & L brickwork with sub- class ‘B’ bricks ( laid dry/mud mortor) straight or curved on plan exc 6 m mean radius complete all as specified and directed. 7 All as per item No 06 as above but except brick complete all as specified and directed. 8 M & L for flush pointing to brick work in CM (1: 3) on laid dry brick work as mentioned in abovecomplete all as specified and directed. 9 Dismantling floor, hearth wall tiling including cement mortar bedding (but not backing) including rubbish off the premises complete all as specified and directed. 10 M&L for vitrified colour Ceramic joint free tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.18 sqm but not exceeding 0.38sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match ceramic coloured tiles joint free decorative (square/ rectangular) area of each tilessqm in floors etc set and jointed in neat cement slurry and pointed with white cement and coloured pigment to match the tiles over 15mm thick screed bed in CM 1:6.complete all as specified and directed. 11 M&L for vitrified colour joint free ceramic tiles 10 mm thick (square/ rectangular)polished, area of each tiles exceeding 0.18 sqm but not exceeding 0.38sqm in skirting/vertical surface etc set and jointed in neat cement slurry and pointed with white cement and coloured pigment to match the tiles including 10mm thick rendering in CM 1:4 on brick wall complete all as specified and as directed. 12 M&L for7 to 8 mm thick non skid ceramic coloured tiles joint free(square/ rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed with white cement and coloured pigment to match the tiles over 15mm thick screed bed in CM 1:6.complete all as specified and directed. 13 M&L for coloured glazed ceramic tiles 450x350x7mm thick, on vertical surfaces such as skirting, dados and risers to stepsetc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match including 10mm thick rendering in CM 1:4 on brick wall complete all as specified and as directed. 14 Dismantling stone slabsof any description or thickness in floors / dados, etc laid bedded and pointed in any mortar complete all as specified and directed. 15 M&L Granite 20 mm thick in steps, pillars, window cills, pillars, window cills, cooking platforms and like laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rounding edges of stone slab one edge and including 20 mm thick screed bed or bedding layer of cment mortar (1:6) complete all as specified and as directed. 16 M & L for machine cut Kota stone slab flooring 20-22mm thick over 15mm thick screed bed in CM 1:6. laid and jointed with grey cement slurry mixed with match the shade of the slab including rubbing and polishing complete all as specified and directed. 17 M & L for kota stone slab 20-22 thick in riser of steps, skirting, dado and pillar laid over 10mm thick backing coat in CM 1:4 and jointed with grey cement slurry mixed with match the shade of the slab including rubbing and polishing complete all as specified and directed. 18 Dismentling wall and ceiling board or insulation board /slabs/blanket any thickness including cover fillets etc all as specified and directed. 19 S&F 605x605mm snap grid of powder coated galvanized iron of angle of size 23mm x 23mm of 30 gauge (Perimeter), T section of size 23mm x35mm main and 23mm x 27 mm (intermediate) of 30 gaugesuitable for false ceiling including GI wire 2 mm thick @ 1200 mm centre to ceter both ways for hanging arragement coplete all as specified and directed. 20 M&L for 4mm thick non asbestos fibre cement building board designer as in ceiling (flat or slopping) of size 600 x 600mm fixed to GI snap grid frame workcomplete all as specified & directed. 21 Dismantling asbestos cement (corrugated, semi-corrugated sheet/ North light curve, Ridge etc.) sheets in roofcoverings complete all as specified and directed. 22 S&F of Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed. 23 Dismentling wall panneling board or insulation board /slabs/blanket any thickness including cover fillets etc all as specified and directed. 24 S&F solid PVC Wall Lining for wall panellingconsisting of 5 mm thickprintedcolour PVC sheet inclusivefixing with all accessoriesat site as per specifications and drawing complete all as specified and directed. 25 M&L for 5 mm thick PVC sheet fillet of width 35 mm for wall panelling inclusive of fixing on to wall to make PVC frame as per specified & directed. 26 Demolition of brick work or stone/boulder masonary built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed. 27 M&L brick work with sub class B bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed. 28 All as peritem no 27 abovebut except bricks complete all as specified and directed. (Note:- Bricks obtained from item No 26) 29 M&L brick work with sub class B bricks straight or curved on plan exc 6m mean radius in half brick thick wall built in CM 1:4 complete all as specified and directed. 30 Taking down cementplaster,and any kind wall cladding tiles/brick stone of any discription on bricks or stone walls/ceiling etc including racking out joints, hacking for kay, scrubbing down with water complete all as specified and directed. 31 M &L for 10 to 12mm smart care ready mix repair plaster is a specially designed ready to use cement-based plaster with high quality polymer additives and well graded sand and fillers which can be used for plastering (as per manufacture instructions) over interior wall surfaces complete all as specified and directed. Note: Coverage for smart care ready mix plaster shalll be 24 - 28 kg / sqm). 32 M &L for 10 to 12mm smart care ready mix repair plaster is a specially designed ready to use cement-based plaster with high quality polymer additives and well graded sand and fillers which can be used for plastering (as per manufacture instructions) over exterior wall surfaces complete all as specified and directed. Note: Coverage for smart care ready mix plaster shalll be 24 - 28 kg / sqm). 33 M & L for washed stone grit plaster on exterior walls in two layers , under layer 12mm th cement plaster 1:4 ( 1 cemant : 4 coarse sand ) furrowing the under layer with scratching tool , applying cement slurry on the under layer @3 Kg of cement per sqm , top layer 15 mm th cement plaster1 :1 / 2 :2 ( 1 cement : 1/2 coarse sand : 2 stone chipping 10 mm nominal size ) in panels with groove all arround as per approved pattern incl. scrubbing and washing the top layer with brushes and water to expose the stone shipping complete all as specified etc 34 Forming groove of uniform size 15 mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens nailed to the under layer incl. removal of wooden battens, repair to the edges of panels and finishing the groove complete all as specified & directed. 35 M&L for rendering 10mm thick in two coats each 5 mm thick plastering on concrete surfaces of ceiling/Chajja in CM 1:3, finished the surfaceeven & smooth complete all as specified and directed. 36 M&L for preparation of newly plastered surfaces of ceiling and applying three coat of white wash complete all as specified and directed. 37 M&L for applying two or more coats of acrylic emulsion polymer paint (waterproof rain coat of Dr. Fixit or equivalent )having, Alkali & fungal resistance, dirt resistance exterior paint of required shade over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new plastered surfaces of wallincluding preparation and over 2-3 mm thick wall care puttycomplete all as specified & directed. 38 M&L for applying Two or more coats of acrylic emulsion polymer paint (wateproof rain coat of Dr. Fixit or equivalent )having, Alkali & fungal resistance, dirt resistance exterior paint of required shade over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old plastered surfaces of wallcare putty over oldplastered surfaces of wallincluding complete removal of existing treatment of walland over 3 mm thick wall care puttycomplete all as specified & directed. 39 Complete removal of existing treatment of old plastered or unplastered surfaces of wallsand applying two coats of oil bound distamper over a coat of average 3 mm thick wall care putty complete all as specified and directed. 40 Preparing new plastered or unplastered surfaces of wallsand applying two coats of oil bound distamper over a coat of average 3 mm thick wall care putty incl rubbing complete all as specified and directed. 41 Complete removal of existing treatment of old stone/concrete surface of ceiling and applying two coats of synthetic enamel paintover a coat of primercomplete all as specified and directed. 42 Taking down chowkats or frame with shutter (without taking off shutters from the frame) not exc 1.5 Sqm each complete all as specified and directed. 43 All as per item No 42 before but exc 1.5 Sqm and not exc 4.00 Sqm each complete all as specified and directed. 44 S&F powder coatedaluminium door & framewith reqd size of aluminium sections weighing 0.55 kg/m including 5 mm thick tinted glass coloured in half portion andin other half portion 8 mm thick ACP sheet of any colour complete and fixed with anodized aluminium snap beading, glazing clips, joining clips, screws,SS hinges and 02 Nos of aluminium handle on each door shutter, aluminium anodized tower bolt 200 mm long 02 Nos on each shutter and mortice lock device complete with double keys for each lock, 01 No Hydraulic door closer for each shutter complete all as specified and directed with following specifications:- (a) Aluminium door frame = 64x38 mm(b)Aluminium style/top& middle rails of shutter = 82.5x44 mm(c) Aluminium bottom rail of shutter = 82.5x44 mm(d) Aluminium door frame with shutters shall be fixed in position in brick wall opening as required according to site conditions including all fastening arrangements etc complete all as specified and directed. 45 S&Fwindowsmade of pre-painted steel (Base steel as per IS 513 of 0.58mm thick “D” Quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 52 x 25mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2nos of heavy-duty stain less steel pivot hinges shall be provided per shutter. The windows should be panelled with 4 mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade). Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self-expanding, screws. Including 10mm square guard bars with 6” (152.4mm) pitch, complete for finished item of work including of all taxes etc as specified and directed. 46 S&F ventilator made of pre-painted steel (Base steel as per IS 513 of 0.58 mm thick “D” Quality galvanized as per IS 277 with Zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 48x50mm, centre mullion should be of 48x50mm, section for shutter should be of 52x 25mm and rebate for Glazed shutter with a 20mm provision for Guard bars/Grills. The sections are to be cut to length metre joined with corner bracket. Centre mullion is to be fixed with mullion cap. Handle, stay, 2 nos. of Stainless Steel heavy duty Pivot hinges shall be provided per shutter the windows fitted with 4mm thick plain float glass with rubber gaskets including fixing the frames in concrete/masonry wall by means of self expanding screws, Including fixed panel beading section should be of 12x12mm. Outer frame and mullions to have 10mm Square guard bars with 6” (152.4mm) pitch etc., complete for finished item of work. 47 M & L mild steel farmed work as in doors (as in ckowkats/shutter frame) or gates of angle or other section with guest plates rail, brasses rail etc exculsive of steel sheeting or other covering hanging also fastening and fixing complete confirming to GdeFe-410-W(Gde-E-250)quality-B including shop coat of red oxide including prepration of surface before fixing complete all as specified and directed. 48 M&L for Mild steel, plain, black sheet 1 mm thickin wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, ncluding bending or turning up, mitred angles, etc. as required 49 S&F of factory made soild PVC door frame of size 50mmx47mm made out of 5mm thick single side prelam PVC sheet reinforced with mild steel square tube , supplying & fixing in opening as per specification and drawing complete all as specified & directed.. 50 S & F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2 mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face with particle board core, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed. 51 Taking down shutter of any description area ofeach shutter exc 2 Sqm complete all as specified and directed. 52 S&F 30mm thick flush door shutter, with particle boardcore construction , and plywood face pannels , commercial type on the both sides complete all as specified and directed. 53 S&F 100 mm long stainless steel hinges type B-12 and fixed with screw/ welding complete all as specified and directed. 54 M&L 100 mm long aluminium anodized handle cast type complete all as specified and directed. 55 S&F 150mm long aluminium anodized barrel tower bolt of extruded section complete all as specified & directed. 56 S&F Aluminium alloy, anodised, 200 mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. 57 S&F Aluminium alloy, anodised, 250 mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. 58 M&L for applying two coats of synthetic enamel paint over a coat of pink primer on wooden surface over 10 cm width or girth including preparation of new or previously untreated wood surfaces complete all as specified. 59 M & L for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed. 60 Dismantling wrought iron or mild steel work any description not otherwise provided for complete all as specified and directed 61 S & F Steel work in tubular/angle irontrusses & postincluding special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed. 62 Demolition of cement concrete in ground floor and paving n exc 15cm thickness (below or above the ground level) built in cement mortar complete all as specified and directed. 63 M&L for 100 mm thick Cement concrete type D-2 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring/ hard standing finishing surface even and rough using broomfinish complete all as specified and directed. 64 M & L hard core of broken stone or boulder having gauge n exc 63mm, deposited, spread and levelled in layers n exc 15 cm thk, watered and rammed to a true surface, complete all as specified and as directed. 65 M&L for providing and laying 80 mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath,parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand,compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified & directed. 66 M & L 75 mm thick Cement concrete type C-2, 1:3:6 (USING 40mm graded stone aggregate) as in plinth protection complete all as specified and directed. 67 M&L for providing, PCC 1:3:6 type C-1 (using 20mm graded aggregate) for embedding hold fasts/coping /padding including necessary form work etc.complete all as specified and directed. 68 S & F150mm floor door stopper of aluminium alloy body and tongue, anodised,with hard drawn steel spring, fixed in floor complete all as specified and directed. 69 S&Fdrapery (curtain)rod 25mm dia Stainless steel grade 304 approved quality and colour includingside cups,fixing arrangement with drilling holes in walls brackets etc complete all as specified and directed. 70 Taking up or down 15mm dia steel tubing and connections etc including cleaning for re-fixing or removal from site complete all as specified and directed. 71 S&F 15 mm bore GI tubes medium grade, galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. 72 Taking up or down20mm dia steel tubing and connections etc including cleaning for re-fixing or removal from site complete all as specified and directed. 73 S&F 20 mm bore GI tubes medium grade, galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. 74 Cutting Chases, pinning in brick/Concreate wall making good to facing where required and pointing in cement mortar 1:3 ends of edges of landing, steps cills sunshade shelves lintles etc and cutting chase for concealed water tubing or or concealed conduit wiring. etc and making good cutting N. exceeding 10 CM girth complete all as specified and directed. 75 S&F in repairs oval type wash basin superior quality 537x439 mm size incl fitted with granite top/baroda green stone over precast RCC slab including waste coupling and incl suitable size CPbottle trap connected upto grating complete all as specified and directed. 76 M&L for demolition of reinforced cement concrete of any description and in any position complete all as specified and directed. 77 M & L for reinforcement cement concrete (Nominal Mix) 1:2:4 type B-1 (using 20mm stone aggregrate) as in slab supported on wallfor wash hand basin complete all as specified and directed 78 M &L forFormwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work and fair finished surfacenot exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed 79 Formwork to edges of concrete flats, treads, breaks in floors,window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide complete all as specified and directed. 80 M & L mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed 81 All as per Item No 80 abovebut 6 to 8mm dia complete all as specified and directed. 82 S & F vitriouschina wash down water closed pan (Pedestal Pattern ) with P and S trapp including connection to trap and cistren and flush pipe (excl flushing cistren)and making good to disturbed surface of floor all fixed as in repairs all as specified and directed. 83 S&F in repairs vitreous China squatting pan (Orissa pattern), white, of size 580x440mm white, with CI P or S trap, integral foot rests including flush pipe, trap, lime concrete bedding inlcuding taking out of old lime concrete bedding, unserviceable connections etc connecting up new and making good disturbe portioncomplete all as specified and directed. 84 S&F in repairbib taps, cast copper alloy, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule orto GI socket or PPR pipe etc making good disturbed portion complete all as specified and directed. 85 S&Fin repair 15 mm bore CP Angle valve two way fancy type with wall flane, highpressure, withcrutch or butterfly handle, screwed both ends foriron pipe orfor unions and fixed complete all as specified & directed. 86 S&F in repair15 mm bore, single lever brass chromium plated wash basin mixer wothout popup waste with 450mm braided hoses opal prime fixed to wash hand basin complete all as specified and directed. 87 S & F in repair 15mm dia Pillar taps, cast copper alloy fancy type, with capstan eads,chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly-nuts,screwed for iron pipe complete all as specified and directed. 88 S&F in repair 15 mm borestop cock, (Concealed type) cast copper alloy, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule orto GI socket or PPR pipe etc making good disturbed portion complete all as specified and directed. 89 S & F in repairs brass chromium plated shower rose 125 mm size, long body ( Arm size should not be less than 450 mm ) with or without swivel joints, any size, including fixing to steel pipe or union etc complete all as specified and directed. 90 S&F in repairs 5 mm thick bevelled edge mirror of selected quality glass of required size and shape with 50x20 mm teak woodpolished beading mounted on 6 mm thick commercial ply wood / ACP / PVCand fixed to wooden plugs with chromium plated brass screw and cup washers complete all as specified and directed. 91 S&F in repairs 600 x 450 mm bevelled edge mirror of selected quality glass 5 mm thick mounted on 6 mm thick commercial ply wood aluminium frame and fixed to wooden plugs with chromium plated brass screw and cup washers complete all as specified and directed. 92 S & F in reapirtoilet paper holder with flat recessed type stainless steel, chromium plated or stainless steel with necessary brass nuts & rubber washers, covered with chromium plated spring complete all as spd and directed. 93 S&F in repair 500 ltrs capacity rotational moulded polyethylene white colour water storage tank double layered, ISI engraved (cylindrical vertical with closed top) hoisted and fixed in position incl dismantling of water tankcomplete all as specified & directed. 94 S & F in repair of plastic WC seat cover and mild steel chromium plated or aluminised hinging device asetc complete all as specified and directed. 95 S & F in repairs flushing health faucet for pedestal pattern WC incl .flexible pipe and brass chromium plated nuts and bolts and water pipe of size 1150 mm long between dia & fixed completed all as specified and directed. 96 S & F in repairsPVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed. 97 S&F in repairs 10 litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and PVC connections 15mm size with PTMT nuts of length 450mm inlcuding taking out of old unserviceable connections etc, connecting up new and making good disturbe portion complete all as specified and directed. 98 Supply & fixing in repair brass CP tubular towel rail, 60 cm long, 20mm bore, chromium plated complete all as specified & directed 99 S & FCI floor trap, plain with grating including jointing with solvent cement (Diameter of outlet 100 mm), jointing to waste pipe and fixed in cement concrete 1:2: 4 (type B1) mixed with pedilite water proofing liquid @ 200ml in 50 kg cement, inlcuding taking out of old unserviceable connections etc, connecting up new and making good disturbed portion complete all as specified and directed. 100 S & FCI floor trap, plain with grating including jointing with solvent cement (Diameter of outlet 75 mm), jointing to waste pipe and fixed in cement concrete 1:2: 4 (type B1) mixed with pedilite water proofing liquid @ 200ml in 50 kg cement, inlcuding taking out of old unserviceable connections etc, connecting up new and making good disturbed portion complete all as specified and directed. 101 S&F in repair CP soap dish brass chromium plated, size 100 x 60mm, fixed to wall with rawl plugs and chromium plated screws complete all as specified and directed. 102 Supply only integral water proofing compound liquid admixture for mortarcomplete all as specified and directed. 103 S&F in repair 500 litres capacity Rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia PVC float valve complete all as specified and directed. 104 Disconnecting existing tanks exc 250 Ltr but not exc 500ltr Cap, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing etc. measured separately) 105 M & L for 5mm thick PVC Sheet board of size 3 x 2 and mounted on wall suitable beading including all the necessary arrangementlike screw bolt etc and basic specification written on it etc cmplete all as specifed and directed. 106 S&F in repairs 600 x 450 mm bevelled edge mirror of selected quality glass 5 mm thick mounted on 6 mm thick commercial ply wood aluminium frame and fixed to wooden plugs with chromium plated brass screw and cup washers complete all as specified and directed. 107 S & F in reapir 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wall complete all as specified and directed. 108 S & F in repair110 mm bore PVC (SWR) bends of any radius complete all as specified & directed. 109 S&F stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100mm dia bore of pipe complete all as specified and directed. 110 Taking down carefully existing unserviceable copper / aluminum point wiring of any description & in any position with and ncluding taking out existing unserviceable conduits or battens of any descriptionwith sunken boxes/junction boxesand all fitting, accessories & fixtures such as switches, ceiling roses, pendants, regulators, socket, light fittings, lamp holders etc but excluding tube light fittings and making good the disturbed surface of walls, floors, ceiling etc to match with the existing surfaces complete all as specified and directed. 111 M&L point wiring with 1.5 sqmm multi stranded copper conductor 1100 volts.grade FRLSH PVC insulated unsheathed cable with proper colour codingdrawn in including PVC concealed conduit not less than 20 mm dia with all accessoriesandFRLSH PVC insulated 1.5 Sqmm multi standard unsheathed copper wire for continues earth, including cutting and chasing of wall surface for laying PVC conduit and modular sunken box and connecting earthand making good to the disturbed surfaceof wall/floor and matching with existing specifications. Connections of cable with MCBs or bus bar shall be done through proper size copper/brassthimbles.Note :Conduit shall be fixed on surfaceof roof with necessary saddles where concealing of conduitis not feasible at no extra cost for the following :- (a) One light /fan point controlled by one switch 112 (b) One 5 pin socket outlet 5 Amps on independent board 113 (c)One 5 pin socket outlet5 Amps on same board 114 (d)One bell/buzzer point controlled by one push button on the same board with other switches or independent 115 All as per item No 111 here in before but with cable size 4 Sq mm for one 5 pin 15/16 Amps socket out let on independent board and multistrand insulated copper earth continuity conductor of size 4 sqmm all as specified and directed. 116 Supply and fixing modular switch piano single pole, one way 6 Amps 1 module, complete all as specified and directed. 117 Supply and fixing modular switch piano flush type 16 Amps single pole one way, one module, complete all as specified and directed. 118 Supply and fixing modular socket outlet2/3 pin 6 Amps combined 2 module, complete all as specified and directed. 119 Supply and fixing modular socketmultipurpose 3 pin 6/16 Amps combined 2 module, complete all as specified and directed. 120 Supply and fixing Modular Bell push 6A 1 module pole, one way, complete all as specified and directed. 121 Supply and fixing in repaircall bell, Ding dong type, 230 volts AC single pole complete all as directed. 122 Supply and fixing modular step typetwo module electronic fan regulator heavy duty 120watts 240 volts. complete all as specified and directed. 123 Supplying & fixing for ceiling rose PVC Polycarbonate isolated body 62.5 x 25 mm, three terminals, complete all as specified & directed. 124 Supply and fixing modular cover plate with frame (inner and outer) 1 module for mounting switch and sockets all as specified and as directed. 125 Supply and fixing modular cover plate with frame (inner and outer) 2 module for mounting switch and sockets all as specified and as directed. 126 Supply and fixing modular cover plate with frame (inner and outer) 3 module for mounting switch and sockets all as specified and as directed. 127 Supply and fixing modular cover plate with frame (inner and outer) 6 module for mounting switch and sockets all as specified and as directed. 128 Supply and fixing modular cover plate with frame (inner and outer) 8 module for mounting switch and sockets all as specified and as directed. 129 Supply and fixing blank spacer plate for single module. 130 Supplying and fixing 20 watt LED battan surface / wall mounted with specially designed powder coated aluminum housing, high optically efficient polycarbonate diffuser, in built electronic driver duly pre-wired upto terminal block, power consumption < 20W, luminaire lumens > 2000 lms, driver efficiency > 85%, power facor > 0.95 THD < 20% as per IEC 61000-3-2, colour temp - 6500 K Surgeprotection 2.5 KV, 50000 burning hrs (min) as per L 70 criteria, two stages isolated constant current operated driver with range 150 - 270 VAC and safety extra low voltage safe level < 60 VDC as per IEC standard with LM 70 & 80 certificationand connecting the same to electric source with & using PVC sheathed and insulated three core copper conductor cable of size 0.75 Sqmm and fixing arrangements for fixing the light fitting, complete all as specified and directed. 131 Supplying and fixing 10 watt LED battan surface / wall mounted with specially designed powder coated aluminum housing, high optically efficient polycarbonate diffuser, in built electronic driver duly pre-wired upto terminal block, power consumption < 10W, luminaire lumens > 1000 lms, driver efficiency > 85%, power facor > 0.95 THD < 20% as per IEC 61000-3-2, colour temp - 6500 K Surgeprotection 2.5 KV, 50000 burning hrs (min) as per L 70 criteria, two stages isolated constant current operated driver with range 150 - 270 VAC and safety extra low voltage safe level < 60 VDC as per IEC standard with LM 70 & 80 certificationand connecting the same to electric source with & using PVC sheathed and insulated three core copper conductor cable of size 0.75 Sqmm and fixing arrangements for fixing the light fitting, complete all as specified and directed. 132 Supply & fixing LED security light compact & trendy of35watt with aluminium pressure diecast housing,IP 65 protection, luminaire lumens > 3000 lumens/W andin built electronic driver prewire upto terminal block with driver efficiency > 85 %, power factor > 0.95, as per IEC 61000-3-2, colour temp 6500 K Surge protection 3.5 KV, 50000 burning hrs (min) as per L70 Criteria, multi stage constant current operated driver with range 150-270 VAC and safety exra low voltage safe load < 60 VDC as per IEC standards with LM 70 & 80 certification complete all as specified, fixed to pole or wall of buiding with and including suitableBracket made out of25 mm dia GIlightgrade pipe, 1.0 m long bent to shape by cutting & weldingas required & directed and fixed withtwo Nos of FI clamps 50x6 mm to be tightened with suitabe size of bolts, nut and washers and including painted withtwo coat of aluminium paint over a coat of red oxide primer, and including connecting the fittingto electric sourcewith & including twin twisted copper flexible wire of size 0.75 Sqmm including all accessories and fixing arrangements for fixing the light fitting complete all as specified & directed. 133 Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. 134 Disconnecting& taking up or down existing unserviceable sub main wiring of copper/aluminium conductor of any description, any size & in any position including taking out existing unserviceable conduits or battens of any description and making good the disturbed surfaces to the existing surfaces complete all as specified and directed. 135 M&L for sub main wiring using two 2x 6 sqmm single core FRLSH PVC insulated, unsheathed stranded copper conductor cable of voltage rating upto and including 1100 Volts drawn in and including concealed PVC conduit (Medium grade) of dia not less than 20 mm with standard accessories along-with one run of PVC (green colour) insulated , unsheathed, stranded copper conductorof size 6 Sqmm as earth continuity conductor connected to earth dolly complete all as specified and directed.Note : Two run of single core PVC cable with one run ofearth conductor and conduit /batten shall be measured as one unit. 136 Disconnecting and taking down old unserviceabledistribution boards any size any type including MCB TPN/SPN/SP etc and making good the disturbed surfaces to the existing surfaces complete all as specified and directed. 137 Supply & fix in repair/replacement of sheet metal enclosure Vertical TPN DB 4 way as per IEC 61439-3, Suitable for Flush Mounting and Surface Mounting, With 160 A Copper Busbar for each phase with 2 Neutral bar, 2 Earthbar and Cable ties for Cable management, fully insulated busbar & shrouded Neutral bars, Improved Pan assembly for ease of installation, Prefitted masking sheet, Reversible Door for IP- 43 DBs, With provision for 160 Amps MCCB as incomer and SP/TP MCBs as outgoing complete all as specified and directed. 138 Supply & fix sheet metal enclosure MCB distribution board. Single pole & neutral 240 volts8 way with IP-43 protection double door complete with appropriate size bus bar and neutral link complete all as specified and directed. 139 Supply & fix sheet metal enclosure MCB distribution board. Single pole & neutral 240 volts12 way with IP-43 protection double door complete with appropriate size bus bar and neutral link complete all as specified and directed. 140 S&F in repair sheet metal enclosure with socket plug top and MCB single pole and neutralwith two pin and earth plug top with one SP MCB 20 Amp 240 volt complete all as specified and as directed. 141 Supply and fixing MCB SP 1 to 32 Amp (C curve)having short circuit rating 10KA, 240 voltscomplete with connection testing and commissioning complete all as specified and directed. 142 Supply and fixing MCB SPN 32 Amp (C curve)having short circuit rating 10KA, 240 voltscomplete with connection testing and commissioning complete all as specified and directed. 143 Supply and fixing in repairMCCB 4 pole, 160 Amps, 50 Hz, Icu=25 KA at 415 volts with thermal magneticalongwith adjustable magnetic protection for current setting Icu=Ics = 100% with adjustable over load setting (minimum 70% to 100%) value from 10 to 15 times of related capacity as per IEC-60947-1 and 60947-2 standard complete all as specified anddirected. 144 M&L for earthing complete with galvanized earth plate electrode 600 x 600 x6mm thick burried directly in ground vertically to a depth not less than 2.25 M below normal ground level ) with top edge of the plate not less than 1.50 M below normal ground level , connected to and including galvanized steel wire 4mm dia as earth lead soldered and rivetedto earth plate by means of nuts, bolts, check nuts & washers, of galvanizediron or steelwith connected to test point and testing on completion including 15mm GI light grade pipe for earth leadprotection from earth point to earth plate, including provnadequate quantity of charcoal dust mixed with35 % common salt to a packed thickness of not less than 15 cm in alternate layers of charcoal and salt on all sides of earth platewith 20mm bore medium grade GI Pipe for watering,GI check nut, funnel and wire meshwith and includingall necessary excavation& earth work in soft/loose soil, returning filling in, removal of surplus soil to a distance 50 metre,,PCC 1:3:6 type C-1 as in earth pit, 40 mm thick RCC cover using cement concrete 1:2:4 type B-1 reinforced with & including 8 mm dia mild steel TMT bar @ 100 mm c/c Both way with suitable handle for lifting arrangement & including form work complete all as specified and shown in electrical plate No 3 of MES SSR Part I 2009 and as directed. NOTES:- On testing, after completion of Job, if desired earth resistance is not obtained, the earthing shall be redone at without any extra cost by contractor. 145 Dismantling, taking down exisitng ceiling fan/Exhaust fan and deposited to E/M store for re-fixing and connecting up including provision of cable from ceiling rose or connector to fan, complete all as specified and directed. 146 Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m complete all as specified and directed. 147 Supply, fixing, connecting & testingceiling fans complete with blades, down rods, with remoteand other accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC), and including connecting wire with new 3 core 0.50 Sqmm PVC insulated and sheathed copper conductor cable from ceiling rose and also writing MES No with black paintcomplete all as specified and directed. 148 Supply and fix in replacement electric water heater, storage type steel body with S/S inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc also writing MES No with black paintcomplete all as specified and directed.
