Providing And Fixing Open Gym Equipments At Kadoli Kalamana And Nimbala Villages Under Csr Under Gouri Pouni Sub Area-Supplying and fixing of open gym equipment such as chest cum seated puller of size 6ft x 2.25ft x 7ft pipe- 110mm, 42mm, 32mm Appolo B class coil pipe,Seat-ms seat 2mm, paint-SD surfacer with paint as per instruction of engineer in charge,excluding cost of excavation and PCC 2 Supplying and fixing of open gym equipment such as Cycle of size 3ft x 1.5ft x 4ft,pipe-58mm, 42mm, 32mm Appolo B class coilpipe, Seat-ms seat 2mm, paint-SD surfacer with paint as per instruction of engineer in charge,excluding cost of excavation and PCC, 3 Supplying and fixing of open gym equipment such as Seating And Standing Twister of size 5ft x 1.25ft x 5ft,110mm, 42mm, 32mm Appolo B class coil pipe, seat-ms seat 6mm, paint-SD surfacer with paint, as per instruction of engineer in charge,excluding cost of excavation and PCC 4 Supplying and fixing of open gym equipment such as Leg press Double of size 5ft x 1.5ft x 5ft, pipe- 110mm, 48mm, 32mm Appolo B class coil pipe,seat-ms seat 2mm, paint-SD surfacer with paint as per instruction of engineer in charge, excluding cost of excavation and PCC 5 Supplying and fixing of open gym equipment such as Surf bourd double of size3ft x 2.5ft x 4.5ft, pipe- 110mm, 48mm,42mm, 32mm Appolo B class coil pipe, Seat-ms seat 2mm, paint-SD surfacer with paint as per instruction of engineer in charge, excluding cost of excavation and PCC 6 Supplying and fixing of open gym equipment such as Shoulder Wheel of size 2.25ft x 1.5ft x 5.5ft, Main pipe- 110mm GI B class pipe Support pipe- 32mm, 25mm GI B class pipe ,Bush-62mm, Bearing-6205 paint-SD surfacer with paint as per instruction of engineer in charge, excluding cost of excavation and PCC 7 Supplying and fixing of open gym equipment such as Eliptical Cross Trainer of size 3.5ft x 1.5ft x 5.5ft, Main pipe- 80mm GI B cass pipe Support pipe- 32mm, 42mm GI B class pipe, Bush-62mm, Bearing-6205, Footrest-2mm Ms sheet paint-SD surfacer with paint as per instruction of engineer in charge, excluding cost of excavation and PCC 8 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means inoundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil. 9 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) derived fromnatural sources: 4 graded stone aggregate 20 mm nominal size derived from natural sources). 10 Providing and fixing of retro- reflectorised informatory sign board rectangular/Square in shape having area greater than 0.9 One Square Meterr made out of 2 mm aluminum sheet bonded with white retro reflective sheeting of Class B ( Type IV High intensitymicro-prismatic grade sheeting-HIP) having pressure sensitive/heat activated adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per IRC:67-2012 Table No 8.3, supported with back support frame25mm x 25mm x 3mm, duly painted on back side with two coats of grey stove enamel paint and supported on two no. mild steel angle iron post 75 mm x 75 mm x 6 mm, 3.5 mt long firmly fixed to the ground by means of properly designed foundation with M25 gradecement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing The angle iron post shall be duly painted with one coat of epoxy primer and two coats of epoxy finish paints having alternate black and white bands of 25 cm widthincluding GI fixures and transportation etc.complete.The nut bolts of board with angle iron post/supporting structure after fixing at site has to be electrically welded. Class B ( Type IV High intensity micro-prismatic grade sheeting-HIP) sheeting shall have 7 years written warranty from the manufacturer and authorised distributor/convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty certificate in original should be submitted to the Engineer in charge by the contractor/supplier. 2mm aluminum sheet Class B 11 Total impact of GST for the purpose of CTC
