Tender For Office Cum Residence Building Work In Range Karauli. - Earth work excavationbymechanical mean ( hydraulic excavatore0 manualmean over areas (exeeding 30 cm in depth 1.5cm in width as well as 10 sqm on plan)including disposel of excavated lead up to50mdispose earth to be levelled all kind of soil 3 Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). 4 RANDOME RUBBLE STONE MASSONARY with hard stone infoundation and plith cement mortar above 30 cm thik wall in cement mortar 1:6 5 Providing and laying damp-proof course with cement concrete gradeM-150 (1 : 2 : 4) mortar prepared with 1% solution of water-proofcompound complete as per specification . 75mm thick. 6 Brick work with F.P.S. bricks of class designation 75 insuperstructure above plinth level upto floor V level in allshapes and sizes in : Cement mortar 1 : 6 (1 cement : 6 coarse sand) 7 Half brick masonry in Superstructure , above plinth level uptofloor V level using bricks of designation 75 8 Centering & shuttering with plywood or steel sheets includingstrutting, propping bracing both ways with steel props andremoval of formwork for upto floor five level for :Suspended floors, roofs, landings, staircases, balconies,girders, cantilevers, bands, coping bed plates, anchor blocks,sills, chhajjas, lintel, beam, plinth beam etc. 9 Providing and laying in position specified grade of cementconcrete for RCC structural elements upto floor five levelincluding curing, compaction, finishing with rendering incement sand mortar 1:3 (1 cement: 3 coarse sand) and makinggood the joints and cost of plastizers (if required ) excludingthe cost of centering, shuttering and reinforcement for Walls(any thickness) including attached pilasters, buttresses, plinthand string courses, fillets, columns, pillars, piers, abutments,posts and struts etc.M20 grade Nominal Mix / Design Mix 10 Steel reinforcementProviding and fabricating reinforcement for R.C.C. workincluding straightening, cutting, bending, placing in positionand binding (including cost of binding wire) all complete up tofloor five level.(Original producers who manufacture billet directly fromiron ores and rollthe bilets to produce steel conforming toIS:1786)Thermo-mechanically Treated bars (Conforming of relevent IScode)(100KG PER CUM C.C) 11 Plaster on new surface on walls in cement sand mortar 1:4including racking of joints etc. complete fine finish :12.2.2 20mm thick . 12 6 mm thick cement plaster to ceiling of mix1:3 (1cement :3-fine sand) 13 Applying priming coat :With ready mix pink or gray primer of approved brand andmanufacture on wood work hard and soft wood. 14 Applying priming coat :With ready mixed red oxide zinc chromate primer of approvedbrand and manufacture on steel galvanised iron/steel works 15 Painting with synthetic enamel paint of approved brand andmanufacture to give an even shade :12.46.1 Two or more coats on new work 16 Supplying and fixing stone lintels/bed plates of approvedquarry rough dressed in cement mortar 1:4 : Upto 15 cm. thick. 17 Providing dab stone over Chajjas duly fixed in cement sandmortar 1:6 complete : 50mm thick 18 Providing and fixing horizontal chajja of Red/ White sandstone 40 mm thick and upto 80 cm projection in cement mortar1:4 (1 cement : 4 coarse sand) including pointing in whitecement mortar 1:2 (1 white cement : 2 stone dust) with anadmixture of pigment matching the stone shade 19 Filling available excavated earth (excluding rock) in trenches,plinth side of foundation etc. in layers not exceeding 20 cm. indepth, consolidating each deposited layer by ramming andwatering including lead up to 50 meter and with all lift 20 Random rubble dry stone Kharanja under floor 21 Providing and laying in position cement concrete includingcuring, compaction etc. complete in specified grade excludingthe cost of centering and shuttering - All work up to plinthlevel.M15 grade Nominal Mix1: 2: 4 (1 cement : 2 coarse sand : 4 graded stone aggregate40mm nominal size).FLOORING 22 Kota stone slab flooring 25 mm thick over 20 mm (average)thick base laid over and jointed with grey cement slurrymixed with pigment to match the shade of the slab includingrubbing and polishing complete with base of cement mortar 1: 4 (1 cement : 4 coarse sand)For area of each slab from 901 to 2000 Sq.Cm :SQM864.00 23 Providing and fixing 1st quality MAT & GLOSSY finishedceramic tile confirming to IS : 13755 and IS : 15622 coloursuch as white, grey, ivory, fume red brown, light green, lightblue and other light shades in floors, steps, pillars etc. laid on abed of neat cement slurry finished with flush pointing in thewhite cement mixed with pigment to match the shade of thetile complete (including the cost of cement mortar bed 1:4). Size 250mm x 375mm 24 P & F 1st qualityHeavy Duty Vitrified Polished Digital tileson floor, skirting and steps etc.in different sizes (thicknessminimum 10mm) with water absortion less than or equal0.08% and conforming to IS 15622 of approved make in allcolour and shade, laid with 20 mm thick CM 1: 4 includinggrounting the joints with white cement and matching pigment betc complete.298mm x 298mm 25 Grading roof for water proofing treatment with waterproffing compound Cement concrete 1:2:4(1 cement : 2 coarse sand : 4 gradedstone aggregate 20 mm nominal size) 26 Providing & fixing precast cement concrete coping 1 : 2: 4 mix 50mm thick complete as per specification : 27 Providing and fixing external grade board solid core singleleaf flush door shutters ISI 2202-67 marked using Phenolformal dehyderesin in glue both sides with approved steelfittings complete as per annexure A :Decorative teak veneer One side 28 Providing and fixing steel glazed window frame made out of80x40 mm hollow sheet section of 16 gauge thickness, jointmitred welded and grinded including hold fast of steel lugs13mm x 3mm and 15 Cm long embedded in C C block 15 x10 x 10 Cm of 1:3:6 nominal concrete andincluding fixing ofpivoted hinges of superior quality, window shutters made outof 50 x 25.0 mm hollow steel section 15 mm paitam of 18gauge thickness, joint mitred and grinded including 10mm x10mm square bars welded to frame for paitam fixing floatglass 4mm thick panes with glazing clips and metal sash puttyand fixing of shutters frames peg stay, U shape handle 100mm long, tower bolts 100 mm long of steel powder coatedsuperior quality including fixing and jointing with framehinges priming coat with steel primer complete in all respectas per direction of Engineer-in –charge9.28.1 Window openabl 29 Providing and fixing in CM 1 : 4 double paitam (rebated)stone door window and ventilator frames of approved quarry:Size 100 x 75mm 30 provide and fixing granite stone slabe mirror posible and machine edge cut thick base of cement mortar 1:3 (1cement 2 marbledust) with pigment to mutch the shade of the marble including grinding ribble and possible comple jhunjhunu/jalore (red/choklete /blake/pink) 31 Supplying and fixing in wall machine cut and polised stone shalevs tands and in cm 1:3 with machene cut edges sand othe approved stone 25 mm thick 32 Extra for provinding edge moduling to 15-18 mm thick marble/granite/kota stone counter vanitiles etc including machine polishing to edge do give high glose finish etc comlete as er desine approved by engineer in charge /granite/kota stone work ful work mounding 33 Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)inrecessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & itsISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thickHot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws,making connections, testing etc. as required.For specification of copperConductor,Phenolic Laminated sheets & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure A attached with this BSR 34 Short point (up to 3 mtr.) 35 Medium point (up to 6 mtr) 36 Long point (up to 10 mtr) 37 Fan 38 Short point (up to 3 mtr.) 39 Medium point (up to 6 mtr) 40 Long point (up to 10 mtr) 41 Wiring of 3 pin 5 amp. light plug point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 KV grade and 1.5 sq. mm nominal size FR PVCinsulated unsheathed flexible copper earth conductor 1.1 KV grade (IS: 694) of approved make in surface/reces group -2 On board 42 S & F follwing sizes (dia.) of ISI marked medium duty PVC conduit along with accessories in surface/ recessed using clamps, fastener as required including cutting the wall , covering conduit with wire mess and making good the same as required. Group-2 25 mm dia 43 Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5,in existingsurface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure A attached with this BSR 44 1 x 1.5 sq.mm 45 2 x 1.5 sq.mm 46 3x 1.5 sq.mm 47 P & F 1.2mm thickM.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm,12 mm dia rod fan hook with 100 mmlength extended on each side . All as per pre approved by Engineer in charge.For additional technical parameters of product / work refer Annexure A attached with this BSR 48 P & F Aluminium sheet 1.0 m thick of following size dia. Including screws, cup washer as required.For additional technical parameters of product / work refer Annexure A attached with this BSR75 mm dia. 49 Providing and fixing of power plug point with non modular accessories as per PWD specification for electrical Works withGalvanized box of 1.2 mm thickwith earth terminal with suitable size phenolic laminated sheet (IS : 2036 -1995) cover including cost of 16 amp. Switch (IS :3854) and 3/6 pin 16 amp. socket outletmaking connection , testing , etc. as required. . For specification ofWiring accessories refer ChapterE - 07 related item &For additional technical parameters of product / work refer Annexure A attached with this BSR 50 Providing & Fixing of IP-20 LED Recessed / Surface Mounted, Round / SqaureSMD Mid Power LED Downlight with power coated die-cast aluminum housingwith UV Stabilized non yellowish Diffuser withBIS complience 2.5 KV surge protected Isolated driver, with Short & Open circuit protection, having efficiency > 85% . System Lumen efficacy of ≥ 110 lm / watt, THD < 10 % , Pf.≥0.95, CRI >80,life time of minimum50000 Burning Hours with , 70% of intial Lumen maintaned till .life ends, CCT 3000°K / 4000°K/5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing onhousing. Surface Mounting (with extruded alumn. Housing )Minimumlumen output 650 lm 51 Providing & Fixing of energy efficient /energy saving IP 20 LED direct retrofit Bulbin existing holder or fixture as required with system lumen efficacy ≥100 lm/Watt output ,pf 0.95 , CRI >70,minimum life time of minimum25000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing onhousing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge . for additional technical parameters of product/ work, refer Annexure A attacheded with this BSR.15 Watt 52 Providing & Fixing ofBEEStar rated copper wounded double ball bearing capacitor start, aluminium body & Metallicblade ceilingfanConforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .SR . 1200 mm Sweep BEE 1 Star rated (service value >=4.0 to < 4.5 ) 53 Providing & Fixing ofshackle (iron hook) made from 2mm nominal thick CRCA sheet and bolts (2nos) of 6mm with spring washer nut, checknut & split pin as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 54 Providing & Fixing ofof ventilating fans Capacitor start, copper wounded, single phase with PVC impeller, ABS body, automatic openable louver shutter in existing opening including making connection, testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR 200 mm sweep
