Redevelopment Of Ntpc Basantpur (Under District Capex Budget 2025 26) Refer To Boq- 1 Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms , incl. disposal or filling of excavated earth wherever requiredas per the directions of Engineer-in-charge . 2 Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) incl. all leads & all leads, lifts and carriages of material by MT/HL 3 Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering- All work upto plinth level 1:3:6 (1 cement: 3 coarse sand : 6 graded stone agg. 20mm nominal size) incl. all leads & all leads, lifts and carriages of material by MT/HL 4 Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1.5:3 (1 cement : 1.5coarse sand :3graded stone agg. 20 mm nominal size)incl. all leads & all leads, lifts and carriages of material by MT/HL 5 Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement.1:1½::3 (1 cement : 1½ coarse sand :3graded stone agg. 20 mm nominal size) incl. all leads, lifts andcarriage of material by M.T. / H.L. 6 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto all level TheMetreo-Mechanically Treated bars of grade Fe-500D or more .incl. all leads & all leads, lifts and carriages of material by MT/HL 7 Centring & shuttering incl.strutting propping etc and removal of form workfor 8 Foundations, footings, bases of columns etc. for mass concrete. 9 Suspended floors, roofs, landings, balconies and access platfoMetres. 10 Edges of slabs and breaks in floors and walls under 20 cm wide 11 Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in : Cement mortar 1:4 ( 1 cement : 4 coarse sand)incl. all leads, lifts andcarriage of material by M.T. / H.L. 12 12mm Cement plaster of mix:1: 6 ( 1 cement : 4 fine sand)incl. all leads, lifts andcarriage of material by M.T. / H.L. 13 15mm Cement plaster on the rough side of single or half brick wall of mix 1: 6 ( 1 cement : 6 coarse sand) incl. all leads, lifts andcarriage of material by M.T. / H.L. 14 Providing and laying vitrified floor tiles in size of tile 600x600 mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% & conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) incl. routing the joints with white cement and matching pigments etc. complete incl. all leads, lifts andcarriage of material by M.T. / H.L. 15 Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete incl. all leads & all leads, lifts and carriages of material by MT/HL 16 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete incl. all leads & all leads, lifts and carriages of material by MT/HL 17 Chequerred precast cement concrete tiles 22mm thick in footpath and courtyard, jointed with neat cement slurrymixed with pigment to match the shade of the tiles, including rubbing, cleaning and curing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) . Ordinary cement without any pigment incl. all leads & all leads, lifts and carriages of material by MT/HL 18 Providing and fixing 35 mm thick wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge :Second class deodar wood 19 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. 20 Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes 110 mmdiametre 21 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, includingcutting and making good the walls and floors whereverrequired:W.C. pan with ISI marked white solid plastic seat and lid. 22 Providing and fixing wash basin with C.I. brackets, 15 mm PTMT pillar cock, 32 mm PTMT waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required. White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm PTMT pillar cock. 23 Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. 24 Providing and fixing uplasticized PVC connection pipe with brass unions 45 cm length15 mm nominal bore 25 Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931 26 Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931 27 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet150 mm diameter 28 Providing and fixing 15 mm nominal bore C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms 29 Providing and fixing PTMT grating of approved quality and colour. Circular type 100 mm nominal dia. 30 Providing and fixing PTMT grating of approved quality and colour. Circular type 125 mm nominal dia with 25mm waste hole 31 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete:Flexible pipe32 mm dia 32 Providing and fixing PTMT soap dish holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106gms. 33 Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with a minimum distance of 37 mm from wall face with concealed fittings arrangements of approved quality and colour, weighing not less than 88 gms 34 Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :100x10 mm 35 Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :150x10 mm 36 Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. 100 mm 37 Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. 125 mm 38 Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :250x16 mm 39 Providing and fixing aluminum casement stays, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 40 Providing and applying 2 mm thickwhite cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 41 Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm) 42 Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work 43 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface. 44 Painting with synthetic enamel paint of approved brand & manufacture to give an even shade.Two or more coats on new work 45 Applying priming coat:With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) 46 Engaging labourfor Clearance of mulba and choked drains from site before execution of work 47 Engaing labour for Carpentor/Plumber for equivalent skilled type 48 Wiring for light point/ fan point/ exhaust fan point/ call bellpoint with 1.5 sq.mm FRLS PVC insulated copper conductorsingle core cable in surface / recessed medium class PVCconduit, with modular switch, modular plate, suitable GI boxand earthing the point with 1.5 sq.mm FRLS PVC insulatedcopper conductor single core cable etc. as required.Group A 49 Wiring for circuit/ submain wiring alongwith earth wire with thefollowing sizes of FRLS PVC insulated copper conductor, singlecore cable in surface/ recessed medium class PVC conduit asrequired. 50 2 x 2.5 SQ.MM 51 2 X 6 SQ.MM 52 2 X 4 sq. mm 53 2 X 1.5 sq. mm 54 Supplying and fixing modular blanking plate on the existingmodular plate & switch box excluding modular plate asrequired. 55 Supplying and fixing suitable size GI box with modular plate andcover in front on surface or in recess, including providing andfixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 Amodular switch, connections etc. as required. 56 Supplying and fixing following modular switch/ socket on theexisting modular plate & switch box including connections butexcluding modular plate etc. as required. 57 Bell push 58 5/6 Amp switch 59 3 pin 5/6 Amp Socket outlet 60 15/16 Amp Switch 61 6 pin15/16 Amp Socket outlet 62 Supplying & fixing of Electrical Accessories 63 4 Deep Box 64 5 Fan Box 65 Ceiling Rose 66 Fan sheet 67 Round sheet 68 Supplying and fixing of following sizes extra down rod with twin core flexible copper wire for ceiling fan.2-0 69 Supplying and fixing of following sizes of PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required. (ISI Make). 70 25 mm 71 32 mm 72 Supplying and fixing call bell/ buzzer suitable for single phase,230 V, complete as required. 73 Supplying and fixing two module stepped type electronic fanregulator on the existing modular plate switch box includingconnections but excluding modular plate etc. as required. 74 Supplying and fixing following way, single pole and neutral,sheet steel, MCB distribution board, 240 V, on surface/ recess,complete with tinned copper bus bar, neutral bus bar, earthbar, din bar, interconnections, powder painted includingearthing etc. as required. (But without MCB/RCCB/Isolator)8 way , Double door 75 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, Ccurve, miniature circuit breaker suitable for inductive load offollowing poles in the existing MCB DB complete withconnections, testing and commissioning etc. as required. 76 Single Pole 77 Single pole & neutral 78 Triple pole & neutral 79 Supplying and fixing following rating and poles230/ 415 V, 10 KA, C curve M.C.Bs in the existing MCB DB complete with connections, testing andcommissioning etc. as required. 80 Single pole & neutral 63 Amp 81 Triple pole & neutral 63 Amp 82 Supply and Fixing Single Pole Blanking Plate in the Existing MCB DB complete as Required. 83 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thickincluding accessories, and providing masonry enclosure withcover plate having locking arrangement and watering pipe of2.7 metre long etc. with charcoal/ coke and salt as required. 84 Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metrebelow ground as strip earth electrode, including connection/terminating with G.I. nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of G.I. nutbolt & spring washer spaced at 50mm) 85 Supply installation testing and commissioning of IP:20 AluminiumBatten 20W-22 W +- 1 W LED Surface Mounted 4 ft. with system lumen efficacy of 100 lm/W and P.F >0.9 THD <20% CCT 6500K,CRI 80 .The LED should have life of 50000 Burning Hours at L70.The inputvoltage shall be 150 V to 270 V.The fixture should have inbuit surge protection of 2KV.Certification-LM 79 and LM 80.The test report should be from Govt. Approved Lab/inhouse NABL Lab. 86 Supply installation testing and commissioning of BLDCCeiling Fan 1200 mm 230V 28 W with Speed RPM 350 with miimum Air delivery 220 CMM including wiring the down rods of standard length(Upto 30 cm)with 1.5 sq.mm FR PVC insulated,copper conductor,single core cable including providing and fixing phenolic laminated sheet cover on the Fan Box etc as Required. 87 Supplying and fixing of following sizes Transair exhaust fan with metal blade complete set on existing holes on wall with necessary connection from ceiling rose to fan using 2 core flexible copper wire.300mm/12 sweep exhust fan
