|
| 1 | DEMOLITION / DISMANTLING & SURFACE PREPARATION: Demolitionof Cement concrete (unreinforced) Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work, Complete in all respect as directed EIC. |
| 2 | DEMOLITION / DISMANTLING & SURFACE PREPARATION: Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles |
| 3 | DEMOLITION / DISMANTLING & SURFACE PREPARATION: dismantling of Textile coverings of any description including frames (if any) and cover fillets (measured flat and not girthed). |
| 4 | DEMOLITION / DISMANTLING & SURFACE PREPARATION: Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. |
| 5 | DEMOLITION / DISMANTLING & SURFACE PREPARATION: Dismantling wrought iron or mild steel work of any description not otherwise provided for |
| 6 | DEMOLITION / DISMANTLING & SURFACE PREPARATION: Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water. The debris to be deposited within distance of about 100 Mts. |
| 7 | DEMOLITION / DISMANTLING & SURFACE PREPARATION: Removing old lime wash (if any), hacking for key, raking out joints of old brick work or stone work built in cement morter or cemnt lime morter not previously plastered; and scrubbing down with water etc. to receive plaster |
| 8 | DEMOLITION / DISMANTLING & SURFACE PREPARATION: Cutting grooves in brick wall, 75mm wide & 65mm deep & shaping horizontal face of groove with cement mortar 1:3. |
| 9 | CUTTING HOLES : Cutting holes into or through cement concrete slabs, chajjas, etc. Superficial area Nexc 100 sq.cm.reinforced cut through |
| 10 | CUTTING HOLES : Cutting holes into or through brick walls in brick walls built, in cement mortar Superficial area Nexc 150 sq.cm. and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required |
| 11 | REMOVAL OF SPOIL : Removing building materials etc. to a distance of 500m or under, beyond the lead included in the rates, including loading, unloading and stacking at the destination.For Aggregate(350cum ÷0.62 cum)=564.52 Load Say 565 Load |
| 12 | PCC IN ROOF: Providing PCC in ratio type-B0, 1:2:4 (12.5mm graded aggregate) in roof kerbs or mud stops, round or chamfered on edges, using coarse sand and approved quality cement as per specifications. The rates include for use of formwork (straight or curved). Complete in all respect as directed by EIC. |
| 13 | PCC IN ROOF: Supply of Liquid water proofing compound Requirement- 350ml per cum. (Material only) |
| 14 | PCC IN ROOF: Finishing cement concrete surface even and smooth using extra cement. M & L |
| 15 | PLASTERING (M&L) :18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand). |
| 16 | PLASTERING (M&L) :Rough cast plaster upto 10 m height above ground level with a mixture of sand and gravel or crushed stone from 6 mm to 10 mm nominal size, dashed over and including the fresh plaster in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand) and top layer 10 mm cement plaster 1:3 (1 cement : 3 fine sand) mixed with 10% finely grounded hydrated lime by volume of cement. Ordinary cement finish using ordinary cement Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.Building Height 13 M. |
| 17 | BRICK WORKS & RCC: Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radious built in thick walls built in cement mortar 1:4 |
| 18 | BRICK WORKS & RCC: RCC in nominal mix B-0 1:2:4 (12.50mm graded aggregate in Beams, cantilevers, bressummers, lintels over 1.5m span |
| 19 | BRICK WORKS & RCC: Reinforment with TMTbars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips |
| 20 | REPAIRING OF DOORS & WINDOWS:Taking down and refixing in same opening only Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded. |
| 21 | REPAIRING OF DOORS & WINDOWS:Supply only Mild steel in flat, round or square bars, z channel, in available lengths conforming to Fe 410-W (Gde-E- 250) quality- A for repairing of windows. |
| 22 | REPAIRING OF DOORS & WINDOWS:Welding in repairs for Thickness of Metal to be welded Exc. 6mm but n.exc 9mm and exc 2.5cm but n exc 5cm in length |
| 23 | REPAIRING OF DOORS & WINDOWS:Supplying Only, Timber 2nd class hardwood (Gamari or equivalent) in clean sawn battens or fillets for repairing of Chowkhats or frames |
| 24 | REPAIRING OF DOORS & WINDOWS:Supplying Only, Timber 2nd class hardwood (Gamari or equivalent), clean sawn boards or planks, width n exc. 25 cm |
| 25 | REPAIRING OF DOORS & WINDOWS:labour in fixing or taking down and refixing in same opening, together with all accessory materials such as nails, screws, wedges, plugs, glue, putty, etc. and also for plugging up old screw holes, etc., and for painting one coat on edges of shutters of doors, windows, etc. eased or fitted. Chowkhats or frames with shutters (without taking off shutters from the frame) size exc 1.5 sq. m but n exc 4 sq. m each |
| 26 | REPAIRING OF DOORS & WINDOWS: Shutters of any description \"refixing\" in same opening includes taking down, easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc. Renewal of builder\"s hardware articles,exc 1 sq. m and n exc 2 sq. m each |
| 27 | REPAIRING OF DOORS & WINDOWS:Butt hinges 100mm long, medium weight, cold rolled mild steel, and fixed |
| 28 | REPAIRING OF DOORS & WINDOWS:Aluminium anodised Barrel Tower Bolts of extruded section -150mm |
| 29 | REPAIRING OF DOORS & WINDOWS:Aluminium Handles, cast type, anodised- 150mm |
| 30 | REPAIRING OF DOORS & WINDOWS:Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed |
| 31 | REPAIRING OF DOORS & WINDOWS:Flush shutters 40mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides and covered with decorative face veneer in both faces with lipping/frame to match |
| 32 | Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of EIC. |
| 33 | Glass PanesHacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones |
| 34 | Glass PanesSheet glass, 4.0mm thick ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane |
| 35 | Glass PanesSheet glass,5.50mm thick ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane |
| 36 | Glass PanesFigured glass, 4.00mm pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane |
| 37 | Glass PanesSupply & Fixing 12mm thick Heat resistant toughened glass with accessories & aluminum framing all complete |
| 38 | PVC DOOR: Supplying & fixing Solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube supplling & fixing in opening as per specification |
| 39 | PVC DOOR: Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.Complete in all respect as directed by EIC. |
| 40 | FALSE CEILING & WALL LINING : Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface with sunk or raised moulding over metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately)Extra over item for any sunk or raised moulding |
| 41 | FALSE CEILING & WALL LINING : Seamless calcium silicate ceiling made out of 1800 x 1200 mm x 12mm thick size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish |
| 42 | FALSE CEILING & WALL LINING : Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flangesof 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. |
| 43 | FALSE CEILING & WALL LINING : Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified |
| 44 | Supply & fixing Clean sawn battens Hardwood 2nd class of Sectional area Exc 5 sq. cm & n. exc. 15 sq. cm at 35cm centre include for all straight and/or raking cutting and waste;Veneered decorative plywood 12mm thick, grade 1 (with BWR resin) with decorative face veneers on front face only; fixed with screws to timber frame work |
| 45 | lnsulated PVC Wall Lining thickness 40mm consisting of PVC Insulated Panels with wood grain printed PVC sheet having expanded polystyrene (EPS) stuck to 2mm thick plain colour PVC sheet duly fitted into the wall as per specifications and drawing |
| 46 | TILING WORK:40mm Cement concrete type B-0, 1:2:4(12.5mm graded aggregate) on floor |
| 47 | TILING WORK:Cutting chases in brick wall, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth |
| 48 | TILING WORK:Non - skid Ceramic joints free colour tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match20mm thick Screed bed of Cement Morterin 1:4 ratio, average 20mm thick for laying of floor finishes. |
| 49 | TILING WORK:Virified Ceramic tiles Light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match 20mm thick Screed bed of Cement Morterin 1:4 ratio, average 20mm thick for laying of floor finishes. |
| 50 | TILING WORK:Virified Ceramic tiles dark shade/ double charge/ ultra charge 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match20mm thick Screed bed of Cement Morterin 1:4 ratio, average 20mm thick for laying of floor finishes. |
| 51 | TILING WORK:Glazed ceramic colour tiles tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to matchRendering 15mm thick on fair faces of brick work or concrete surfaces built in cement morter 1:4 |
| 52 | TILING WORK: Machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete20mm thick Screed bed of Cement Morterin 1:4 ratio, average 20mm thick for laying of floor finishes. |
| 53 | TILING WORK: Rounding to edges of Cudappa stone slabs one edge, such as in steps, cooking platform, and other similar situations |
| 54 | TILING WORK:20mm Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.Rendering/ Plastering 20mm thick on fair faces of brick work or concrete surfaces built in cement morter 1:4 |
| 55 | TILING WORK:16 to 18mm Dholpur stone cladding gang saw cut with machine cut edges, uniform colour of each stone size exceeding0.5 sqmStones shall be laid in straight courses about 50mm high and joined in cement and stone dust mortar 1:3 and recessed pointed with an admixture of white cement and Dholpur stone dust 1:1. fixed with and including one number SS clamps (grade -202) of flat 30mm X 2mm, 150mm long made to shape in each slab, making V groove at top and bottom of stone and drilling hole for hold fastener, polishing, rubbing & includingsilicon treatmentRendering Plastering 20mm thick on fair faces of brick work or concrete surfaces built in cement morter 1:4 |
| 56 | TILING WORK:Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 |
| 57 | TILING WORK:Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc.conforming to Fe.290.Gde-E-165 including allow for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also forwedging, plumbing, truing up, drilling and fixing complete. painted one shop coat of zinc chromate primer paint (including preparation of surface) at Contractor’s workshop before fabrication |
| 58 | TILING WORK:MS Framework conforming to Fe-290 Gde-E 165 Joist, channel, angle, or tee sections, fixed independently, withoutconnecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated)painted one shop coat of zinc chromate primer paint (including preparation ofsurface) at Contractor’s workshop before fabrication |
| 59 | TILING WORK:Floor polishing on masonry or concrete floors with wax polish of approved brand and manufacture. |
| 60 | Designing, fabricating, testing, installing and fixing in position CurtainWall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including:(a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design.(b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium compositepanel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. |
| 61 | Plumbing:15mm dia Unplasticised PVC (UPVC) pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., include for pipes including short lengths, with all pipe fittings such as ends, elbows, unions, tees, reducing tees, adoptors, sockets, plugs, hose clips etc. and fixing to walls etc, complete with saddles (snap clips), wall clips, hooks, protective mild steel tube sleeves and cutting through walls, floors and their making good or laying in trenches and also cutting, screwing and waste AND include for labour, tools and plants. |
| 62 | Plumbing:galvanised steel (Gl) tubing with screwed socket joints, together with all tube fillings (such as bends, elbows, tees, short pieces, connectors, backnuts, diminishing pieces, caps, plugs and unions, etc.) and fixing complete with clips, wall hooks, wooden plugs, or laying in trenches, etc., also for cutting, screwing and waste and for making forged bends on piping as required.Tubes, galvanised, 25mm dia pipe medium grade with all fitting and fixed complete to walls and ceilings or laid in floors.a) Tubes, galvanised, 25mm dia pipe medium grade |
| 63 | Plumbing:galvanised steel (Gl) tubing with screwed socket joints, together with all tube fillings (such as bends, elbows, tees, short pieces, connectors, backnuts, diminishing pieces, caps, plugs and unions, etc.) and fixing complete with clips, wall hooks, wooden plugs, or laying in trenches, etc., also for cutting, screwing and waste and for making forged bends on piping as required.Tubes, galvanised, 25mm dia pipe medium grade with all fitting and fixed complete to walls and ceilings or laid in floors.b) Tubes, galvanised, 15mm dia pipe medium grade |
| 64 | Vitreous China wash down water closet pan (pedestal pattern), white, fixed in repair include for supply & fixing the following component parts, viz:(i) 18302Vitreous China wash down water closet pan (pedestal pattern), white(ii) \"P\" or \"S\" trap, 110mm (iii) Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated oraluminised hinging device (iv)PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets),(v)Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern including jointing to socket of flushing rim (with and including India rubber cone joint and connecting pipe to union of flushing cistern, in let and overflow pipes connecting only to flushing cistern. (vi) 110mm PVC (SWR) WC connector with lip ring (vii)PVC connections 15mm size with PTMT nuts of length 450mm(viii) Bib tap standard of PTMTwith nozzle, (Minimum weight 15mm-95gms) any colour high pressure screwed for iron pipe and fixed.(ix) Bib tap standard of PTMTwith long body (Minimum weight 15mm-120gms) any colour high pressure screwed for iron pipe and fixed.(x) Angle stop valve of PTMT any colour high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms)(xi)Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 65 | Water closet (Squatt pattern) complete fixed in repair including provision of lime concrete bedding white include for supply & fixing the following component parts, viz:(i) 18306vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests(ii) \"P\" or \"S\" trap, 110mm (iii) Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated oraluminised hinging device (iv)PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets), (v)Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern including jointing to socket of flushing rim (with and including India rubber cone joint and connecting pipe to union of flushing cistern, in let and overflow pipes connecting only to flushing cistern.vi) 110mm PVC (SWR) WC connector with lip ring(vii)PVC connections 15mm size with PTMT nuts of length 450mm(viii) Bib tap standard of PTMTwith nozzle, (Minimum weight 15mm-95gms) any colour high pressure screwed for iron pipe and fixed.(ix) Bib tap standard of PTMTwith long body (Minimum weight 15mm-120gms) any colour high pressure screwed for iron pipe and fixed.(x) Angle stop valve of PTMT any colour high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms)(xi)Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 66 | Supply & Fixing in repair Vitreous China Urinal, Half stall type, white omplete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement;flush pipe, grating and Union for discharge pipe.(ii) PVC connections 15mm size with PTMT nuts of length 450mm(iii)Waste coupling of PTMT (half or full threaded) suitable for urinals, (Minimum weight 32mm-45gms)(iv)Angle stop valve of PTMT any colour high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms) |
| 67 | supply & fixed in repair Vitreous China squatting plate urinal in toilet |
| 68 | Providing and fixingGranite Stone of approved shade 75 mm high, 50 mm deep and 18 mm thick stone slab table rubbed, edges rounded and polished,FIXED IN URINAL PARTITIONS by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. |
| 69 | WASH BASINVitreous China wash basin, white, flat back, size 550x400mm including brackets cutting for and pinning in ends of brackets includingfor fixing taps, waste fittings and union, plugs and chains and connecting up to supply pipes, wastes or traps; screws, plugs, cement mortar, red lead cement and other subsidiary materials required for fixing.PVC connections 15mm size with PTMT nuts of length 450mm Angle stop valve of PTMT any colour high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms)Pillar taps of PTMT fancy type. any colour high pressure screwed for iron pipe and fixed.(Minimum weight 15mm-120gms)18132 Waste coupling of PTMT (half or full threaded) . (Minimum weight 32mm- 45gms) |
| 70 | S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm. Bib tap standard of PTMTwith long body (Minimum weight 15mm-120gms) any colour high pressure screwed for iron pipe and fixed. |
| 71 | PVC Cistern CAPACITY 10LitreSupply & Fixing in repair, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets.(ii) supply & fixing Flush pipes of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern to squatt pattern closet including all joints and making good to the floor(iii) PVC connections 15mm size with PTMT nuts of length 450mm |
| 72 | 15mm Dia Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed shanks and fly-nuts,screwed for iron pipe and fixed |
| 73 | 15mm Dia Bib taps, cast copper alloy fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed |
| 74 | Self-closing taps, cast copper alloy,chro-mium plated, screwed for ironpipe and fixed |
| 75 | Providing and fixing on wall face unplasticised Rigid PVC SWR Pipe (Type-B) conforming to IS : 13592 including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, Complete in all respect. 160 mm dia-PVC pipe (Single Socketed) |
| 76 | Providing and fixing on wall face unplasticised Rigid PVC SWR Pipe (Type-B) conforming to IS : 13592 including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, Complete in all respect. 160 mm dia-PVC pipe (Double) |
| 77 | Providing and fixing on wall face unplasticised Rigid PVC SWR Pipe (Type-B) conforming to IS : 13592 including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, Complete in all respect.160 mm dia-PVC Bend |
| 78 | Providing and fixing on wall face unplasticised Rigid PVC SWR Pipe (Type-B) conforming to IS : 13592 including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, Complete in all respect.160 mm dia-PVC Single Tee equal or unequal |
| 79 | Providing and fixing on wall face unplasticised Rigid PVC SWR Pipe (Type-B) conforming to IS : 13592 including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, Complete in all respect.160 mm dia-PVC Double Tee equal or unequal |
| 80 | Providing and fixing on wall face unplasticised Rigid PVC SWR Pipe (Type-B) conforming to IS : 13592 including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, Complete in all respect.75mm dia unplasticised Rigid PVC SWR Pipe (Type-B) conforming to IS : 13592 including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion singlesocketed, in any lengthlaid in trenches or in floors |
| 81 | Providing and fixing on wall face unplasticised Rigid PVC SWR Pipe (Type-B) conforming to IS : 13592 including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, Complete in all respect.75mm dia PVC (SWR) bends anyradius |
| 82 | 110mm dia unplasticised Rigid PVC SWR Pipe (Type-B) conforming to IS : 13592 including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion singlesocketed, in any lengthlaid in trenches or in floors |
| 83 | 110mm dia PVC (SWR) bends anyradius |
| 84 | PVC (SWR) reducers 160/110 |
| 85 | ANTI TERMITE TREATMENT (M&L):Providing and injecting chemical emulsion IN FLOOR & WALL JUNCTION for Post Constructional Antitermite Treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron |
| 86 | ANTI TERMITE TREATMENT (M&L): Providing and injecting chemical emulsion at points of contact of WOOD WORK by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same. |
| 87 | PAINTING: Weather Coat Paint: Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over surfaces. |
| 88 | PAINTING: Weather Coat Paint: Finishing walls with textured exterior paint of required shade :Old work (Two or more coats on existing cement paintsurface applied @ 3.28 ltr/10 sqm. |
| 89 | PAINTING: Distemper: Preparation of surface by Washing, rubbing down and stopping of distempered and painted surfaces.One coat Cement wash with Portland cement slurry to a smooth bodied opaque finish on newly plastered surfaceTwo coat Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer\"s specification. |
| 90 | TAKING DOWN :Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) |
| 91 | SCAFFOLDING : Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/ structure, upto 25 metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. |
| 92 | MCCB 200A (M&L): Supply and fixing of MCCB 200A,36KA, 4P, 415V AC, 50Hz with Spreader Terminal, Rotary Handleand Adjustable type Release , Confirms to – IS/IEC 60947-2, complete in all respect. Make: SIEMENS/L&T. |
| 93 | ON LOAD CHANGE OVER SWITCH 200A (M&L): Supply and fixing of on-load change over switch, rating 200 amps, 1100 volts, Triple pole, mechanically operated, mounted on insulator and steel frame, with operating mechanism. Complete in all respect. Make: SIEMENS/L&T. |
| 94 | MS SHEETING (M & L): Supply, fixing & febrication of mild steel, plain sheet of thickness 1.60mm, enclosure of 200A MCCB enclosures, feeder piller enclosure with gasket and space for cable termination, including 2-coat of red oxide primer, complete in all respect. |
| 95 | BUSBAR 12-WAY DB 200 AMP (M&L): Supply, fixing & connection of 200 amps. Bus-Bar DB with copper busbars and Sheet metal enclosure, triple pole and neutral, 12-way, 415 V, double door, complete in all respect. |
| 96 | LT CABLE 50 SQ.MM.(M & L): Supply& laying of PVC/XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 50sq.mm., 3.5core, confirming to IS:7098, complete in all respect. Make: CRYSTAL, GLOSTER, FINOLEX, POLYCAB, UNIVERSAL, HAVELLS. |
| 97 | JOINTING / TERMINATION OF LT CABLE 50 SQ.MM. (M & L): Supply and fix cable jointing / Termination for 1.1 KV grade cable for complete with Jointing /Termination material (aluminium cable sockets, brass cable glands, PVC insulation tapes etc.)and accessories suitable for 3½ core XLPE armoured Al conductor cable of size 50 sq mm., complete in all respect. |
| 98 | EXCAVATION SOIL: Excavation of hard/dense soil over areas, n exc 1.5 m deep in cable trenches and getting out. |
| 99 | REFILLING OF SOIL: Returning, filling in, inc spreading, levelling, watering and well ramming of excavated soil for cable trenches. |
| 100 | STEEL PIPE 80 SQ.MM.(M & L): Galvanised Steel Tubing (Piping), medium grade of bore size 80mm, including all fixing & fitting (MS clamps, flats) laid across drains, roads, fixing complete with all respect. Make: TATA, JINDAL, BANSAL. |
| 101 | SAND FILLING (M & L): Sand filling under cable trenches over laid cables. |
| 102 | BRICK OVER LAID CABLE (M & L): Supply & laying of Bricks; common burnt clay building Old size bricksbricks, sub-class ‘A’ designation 75 over laid cable on edged bricks. |
| 103 | BRICK EDGING (M&L): Supply & laying of Continuous brick edging; with width equal to the depth of the brick, laid dry, on edge With burnt clay bricks of sub class B on two sides of laid cable. |
| 104 | MAIN WIRING IN PVC CONDUIT (M&L): Supply, fixing & connection of concealed main wiring with the size 4x16.0 sq. mm + 2x10.0 sq.mm earth wire of FR PVC insulated copper conductor, single core cable in PVC conduit in surface / recessed / conseled as required. Make of cable: FINOLEX / ANCHOR / HAVELLS / MESCAB. |
| 105 | STEEL METAL ENCLOSURE-1 FOR 63A TPN-MCB DB (M&L): Supply, fixing & connection of Sheet metal enclosure for DB`s MCB to be used, Triple pole and neutral, 4-way 4 way with 200 amps rated busbar, 415 V, double door, complete in all respect. Make: SIEMENS / L&T / SCHNEIDER. |
| 106 | MINIATURE CIRCUIT BREAKER (MCB) 63A, TPN (M & L): Supply, fixing & connection of Miniature Circuit Breaker of rating 63A, TPN, 415V, complete in all respect. Make: SIEMENS / L&T / SCHNEIDER. |
| 107 | MINIATURE CIRCUIT BREAKER (MCB) 100A, TPN (M & L): Supply, fixing & connection of Miniature Circuit Breaker of rating 100A, TPN, 415V, complete in all respect. Make: SIEMENS / L&T / SCHNEIDER. |
| 108 | STEEL METAL ENCLOSURE FOR 20A DP-MCB DB (M&L): Supply, fixing & connection of Sheet metal enclosure for DB`s MCB to be used, Single pole and neutral, 2-way, 240 V, single door, complete in all respect. Make: SIEMENS / L&T / SCHNEIDER. |
| 109 | MINIATURE CIRCUIT BREAKER (MCB) 20A, DP (M & L): Supply, fixing & connection of Miniature Circuit Breaker of rating 20A, DP, 240V, complete in all respect. Make: SIEMENS / L&T / SCHNEIDER. |
| 110 | SUB-MAIN WIRING IN PVC CONDUIT (M&L): Supply, fixing & connection of concealed sub-main wiring for circuit / submain wiring along with earth wire with the size 2x4.0 sq. mm + 1x2.5 sq. mm earth wire of FR PVC insulated copper conductor, single core cable in PVC conduit in surface / recessed / conseled as required. Make of cable: FINOLEX / ANCHOR / HAVELLS / MESCAB. |
| 111 | STEEL METAL ENCLOSURE FOR 63A DP-MCB DB (M&L): Supply, fixing & connection of Sheet metal enclosure for DB`s MCB to be used, Single pole and neutral, 2-way, 240 V, single door, complete in all respect. Make: SIEMENS / L&T / SCHNEIDER. |
| 112 | MINIATURE CIRCUIT BREAKER (MCB) 63A, DP (M & L): Supply, fixing & connection of Miniature Circuit Breaker of rating 63A, DP, 240V, complete in all respect. Make: SIEMENS / L&T / SCHNEIDER. |
| 113 | MODULAR METAL FLUSH BOX - 12 MODULE (M & L):Supply & fixing of Metal flush box for 12 modules. |
| 114 | MODULAR METAL FLUSH BOX - 6 MODULE (M & L):Supply & fixing of Metal flush box for 6 modules. |
| 115 | MODULAR WHITE COVER PLATE WITH FRAME - 12 MODULE (M & L):Supply & fixing of White cover plate with frame for 12 modules. |
| 116 | MODULAR METAL COVER PLATE WITH FRAME - 6 MODULE (M & L):Supply & fixing of White cover plate with frame for 6 modules. |
| 117 | MODULAR SWITCH 6A (M&L): Supply, fixing & connection of Modular switch 1 way 6A, 1 module. Make: PRITAM / ANCHOR / KOLOR / POINTER. |
| 118 | MODULAR SWITCH 16A (M&L): Supply, fixing & connection of Modular switch 1 way 16A, 1 module. Make: PRITAM / ANCHOR / KOLOR / POINTER. |
| 119 | MODULAR SOCKET OUTLET 6A (M&L): Supply, fixing & connection of Socket, 6A - 2/3 pin combined 2 module. Make: PRITAM / ANCHOR / KOLOR / POINTER. |
| 120 | MODULAR SOCKET OUTLET 16A (M&L): Supply, fixing & connection of Socket 6A/16A - 2/3 pin combined 2 module. Make: PRITAM / ANCHOR / KOLOR / POINTER. |
| 121 | POINT WIRING FOR LIGHT OR FAN (M & L): One light point or one fan point controlled by one switch wiring with copper conductor, PVC single core sheathed FRLS ofcables 1.5 sq.mm size in PVC Conduit, complete in all respect. Make of cable: FINOLEX / ANCHOR / HAVELLS / MESCAB. |
| 122 | POINT WIRING FOR SAME BOARD 6A SOCKET (M&L): One 3 pin socket outlet 5 amps on the same board with other switches with copper conductor, PVC single core sheathed FRLS ofcables 1.5 sq.mm size in PVC Conduit, complete in all respect. Make of cable: FINOLEX / ANCHOR / HAVELLS / MESCAB. |
| 123 | POINT WIRING FOR SAME BOARD 16A SOCKET (M&L): One 3 pin socket outlet 15 amps on the same board with other switches with copper conductor, PVC single core sheathed FRLS ofcables 4 sq.mm size in PVC Conduit, complete in all respect. Make of cable: FINOLEX / ANCHOR / HAVELLS / MESCAB. |
| 124 | CEILING ROSE (M & L): Ceiling rose, 3 phase / PVC / polycarbonate, isolated body. |
| 125 | MODULAR FAN REGULATOR (M & L): One light point or one fan point controlled by one switch wiring with copper conductor, PVC single core sheathed FRLS ofcables 1.5 sq.mm size in PVC Conduit, complete in all respect. Make of cable: FINOLEX / ANCHOR / HAVELLS / MESCAB. |
| 126 | LED RECESSED TYPE FITTINGS (M&L): Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete. Make of Light: PHILIPS / SURYA / HAVELLS / BAJAJ / SYSKA. |
| 127 | GI RAIL/CHANNEL/ANGLE/FLAT (M&L): Supply, fixing & febrication of rolled GI rail, channel, angle and flat [Fe-290(Gde E-165)], fixed independently for fixing of transformer etc., complete in all respect. |
| 128 | BLDC CEILING FAN (M&L):Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1400 mm sweep. Min air delivery 245 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC). Make of Fan: PHILIPS / ATAMBARG / HAVELLS / BAJAJ. |
| 129 | PIPE EARTHING (M & L): Supply & making of Pipe Earthing, complete with galvanised steel pipe electrode, 40mm bore, medium grade, 2.5 metres length, buried directly and preferably vertically in ground with top edge not less than 1.25 metres below ground level connected by using galvanised iron 25 x 4mm strip as earthing lead all as shown in Plate No. 4 to the earthing test point, all as specified and indicated including testing on completion. This includes making of pit, providing CI cover, funnel with watering pipe, wire mesh, name plate and GI earth lead protection pipe. |
| 130 | EARTH CONTINUITY CONDUCTOR (M & L): Earth ontinuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 25 x 4mm galvanised iron strip. |
