Tender For Additional Alteration Of Bldg No P22 At Danapur Cantt; 1 Demolition of cement concrete (unreinforced) in ground floors and paving n exc 15 cm thickness (below or above ground level)all as specified and directed 2 Dismantling of floor, hearth, walls and roof tiles including cement mortar bedding but not backing and rubbish off permises complete all as specified and directed. 3 Demolition of reinforcement cement concrete above the ground floors n exc 15 cm thickness (Reinforcement cut as required to facilitate demolition)such as cooking platform, chajjas etccomplete all as specified and directed. 4 M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in column, pillar etc.complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item) 5 M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5 m sapn and like complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item) 6 M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and like complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item) 7 M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in Chajjas and like complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item) 8 M & L for use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions in rough finished surface of concrete complete all as specified and directed. 9 M & L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of concrete complete all as specified and directed. 10 M & L for use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar works not exc. 200 mm thick horizontal or slopping in rough finished flat surface of concrete complete all as specified and directed. 11 M & L for use and waste of Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizon tal or sloping and similar work exc 10cm but n exc 20cm wide in rough finished flat surface of concrete complete all as specified and directed. 12 M&L mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cracking, bending, spirally for hopping for columns hookings ends and binding with and incl mild steel wire (annealed) not less the 0.9mm dia or securing with clips complete. 13 All as per item No 12 above but 5 mm dia and over in stirrups, spacers and binders complete. 14 M&L10 mm thick plastering on roof surfaces/concrete surface in CM 1:4complete all as specified and directed. 15 Removal of demolished material upto a distance of 5 km ( out of defence land) complete all as specified and as directed. . 16 Excavation in trenches in soft/ loose soil not exc 1.5m wide and not exc 1.5m deep for foundation, pier holes etc n. exc 10sqm on plan and getting outall as specified and directed 17 M&L cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate in foundation, filling and mass concrete complete all as specified and directed. 18 M&L hard core of broken bricks of gauge n exc 63mm deposited, spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface complete all as specified and directed. 19 M&L 75 mm thick plain cement concrete (1:2:4), type B-0, using 12.50 mm graded stone aggregate as in sub base of floor, sub bases, floor and paving floors including finishing the surface rough for laying kota stone / tiles complete all as specified and directed 20 M&L for non skid colouredtiles 7 to 8 mm thick(square / rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc over and including15 mm thick screed bed or bedding layer of mortarfor laying floor finishes in CM 1:6for laying of floor tiles, set & jointed in neat cement slurry and pointed with whitecement mixed with pigment to match the shade etc.complete all as specified and directed. 21 M&L for 10mm thick Dark shadevitrified ceramic tiles in floors, exceeding 0.42 sqm n exc 1.00 Sqmset & jointed in neat cement slurry & pointed in white cement mixed with pigment to match including screed bed or bedding layer of15mm thick in CM 1:6, complete all as specified & directed. 22 M&L for 10mm thick Dark shade vitrified ceramic tiles exceeding 0.42 sqm n exc 1.00 Sqm on vertical surface such as skirtings, dados etc, over & including 10mm thick rendering in cement mortar (1:4) set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles complete all as specified & directed. 23 Demolition ofbuilt in cement mortar including all quions, arches, pillars, etc complete all as specified and as directed. 24 Taking down cement plaster on wall/ceiling /roof etcincluding raking out joints, hacking for key and scrubbing down with water etc complete all as specified and directed.. 25 M&L for old size Brick work with sub- class ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6complete all as specified and directed. 26 M&L brick work with sub class ‘B’ bricks straight or curved on plan to any radius built in CM 1:4 in half brick thick wall complete all as specified and directed.. 27 M&L 15mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:6 finished even and smooth (without using extra cement)complete all as specified and directed. 28 M&L for Rendering 15 mm thick in cement mortar 1:4 on concrete surfaces mixed with liquid water proofing compound@ 200 ml/50 kg per bag of cement or as per manufacturar instruction finished even and smoothwithout using extra cement over roof slab complete all as specified and directed .NOTE: water proofing compound shall be measured and paid seperately. 29 M&L rendering 5 mm thick in cement mortar 1:3 on concrete surfaces of ceiling and finishing the surfaces even and smooth complete all as specified and as directed.. 30 Supply only water proofing compound (liquid), ISI marked. 31 Taking down chowkats or frame with shutters (without taking off shutters from the frames) n. exc 1.5 Sqm each complete all as specified and directed. 32 All as per above item no 31 but exc 1.5 Sqm and n.exc. 4 Sqm each. 33 Taking down shutters of any description exc 1.00 Sqmand n exc 2.00 Sqm each complete all as specified and directed. 34 Supply & Fixing of 1st class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed 35 Supply & Fixing of 35mm thick engraved moulding Flush shutters on both side ofsolid core constructionfitted to chowkats complete all as specified and directed. 36 Supply & Fixing of 1st class Hardwood Glazed and skeleton shutters, 30mm thick open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc, sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkat complete all as specified and directed 37 S&F 100 mm size Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-11 all as spd. 38 S&F 75 mm size Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-11 complete all as specified and directed. 39 S&F Brass, sliding door bolt 300mm long with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed. 40 S&F 300 mm long Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts complete all as specified and directed. 41 S&F 200 mm long Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and directed. 42 S&F floor door stopper 140 mm overall length of cover plate of brass body and tongue, anodised. With hard drawn spring, fixed in floor complete all as specified and directed. 43 Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 44 Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) [and 5mm thick glazing with selected quality glass. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) 45 S&FStainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. 46 S&F Toughned glass 08mm thick as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required complete all as specified and as directed. 47 M&L for applying POP Moulding of (100-150mm) in size for internal wall surface including edges, corners on wall and celing portion as required complete all as specified and directed. 48 M & L Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over one coat of3.00mm putty and including priming coat ofprimer applied @ 0.90 litre/ 10 sqm at all heights complete all as specified and directed. 49 M&L for cutting holes in brick wall built in cement mortar for inserting holdfast, walls exc half brick but n.exc one brick thick and making good dismantled portion in cement mortar 1:3 complete all as specified and directed. 50 S&F in repair stainless steel designer curtain rod fancy type curtain rod 20 mm dia including brackets as approved complete all as specified and directed. 51 Dismantling wall and ceiling board (fiber, pulp, PVC, insulation etc) or insulation boards / slabs / blankets, any thickness including cover fillets complete all as specified and directed. 52 S & F for GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre, size of grid 605mm x 605mm complete all as specified and directed. 53 S & F for hangers 6 mm dia GI (upto 1200mm length adjusting level fixed to roof/slabs by means of ceiling cleats made out of GI flat 40X30 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and directed. 54 M&L Providing and fixing Gypsum Board 12mm thick in ceiling on timber / GI / Aluminium framework fixed with screw as per manufacturers instructions complete all as specified and directed. 55 M & L in repair 0.9mm Decorative laminate typeof surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturers instruction complete all as specified and directed. 56 M&L in repair Veneered plywood 12mm thick, grade 1 (with BWR resin) with decorative face veneers on both faces, fixed with brass screws and cups complete all as specified and directed. 57 Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors complete all as specified and as directed. 58 Dismantaling of Asbestos cement/GI (corrugated/semicorrugated, etc.) sheets in roof coverings complete all as specified and directed. 59 Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed. 60 S&F rolled mild steel Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Fe 410W Grade E 250 complete all as specified and as directed. 61 S&FPre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screwscomplete all as specified and directed. 62 M&L for two coats of weather coat paint (apex) on new surfaces of wall including preparation ofplastered surfaces complete all as specified and directed. 63 M & L for preparation of newly plastered surfaces ofwall & concrete and applying 2 mm thick wall care putty including preparation complete all as specified and directed. 64 M&L for Prepation of surface incuding cleaning, repair proper cracks if any, priming the surafce and then applying two coat ofultra damp proof paint for any surface complete all as specified and directed. 65 Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed. 66 Taking down carefully main switches DBs/ MCB DBs with MCB and making good the disturbed surfaces of wallsas directed. 67 Taking down carefully copper / aluminium sub mainwiring including teak wood batten / conduit and making good the disturbed surface of walls as directed. 68 Refixing old serviceble any types of lumanirious like Tube light set, ceilling light, building security light etc, C/Fan, E/Fan, wall mounted fan including all necessary fixing accesories, flexible wiring from ceilling rose to items complete all as specified and as directed. Note: Minor repairing likeball bearing, overhaulling for fans, cleaning, nut & bolts, screw etc are deemed to be included with the quoted rate of this item. 69 M & L for Point wiring with PVC insulated PVC unsheathed electric FRLS cable 1100V grade single core having multi stranded copper conductor of size 1.5 Sqmm nominal cross sectional area in & including non metallic rigid PVC conduit ISI marked medium grade not less than 20 mm dia ,with modular box with all conduit accessories in surface wiring or concealed wiring system as per original ground requirement by cutting/chesing of wall and making good disturbed surface of wall with cement morter and existing colour painting after fixing of conduit & 1.5 sqmm green PVC insulated unsheathed copper conductor as a earth wire connected to earth dolly by providing lugs for one light/fan point controlled by one switch complete all as specified and as directed. Note : wiring with 2 X 1.5 sqmm +1 X 1.5 sqmm run with proper colour code as per IE rules and 1 run PVC conduit shall be measured in one unit. 70 All as per item no 69 above but one 5 Amps socket out let point controlled by one switch on same board with other switches. 71 All as per item no 69 above but one 5 Amps socket out let point on independent board controlled by one switch. 72 All as per item no 69 above but wiring with 2.5 sqmm single core copper conductor for one socket out let 5/15/16 amps point on the independent board. (Note : wiring with 2 X 2.5 sqmm +1 X 2.5 sqmm run with proper colour code as per IE rules measured in one unit) 73 All as per item no 69 above but wiring with 4.0 sq mm single core copper conductor for one socket out let 15/25 amps point on the independent board.(Note : wiring with 2 X 4.0 sqmm +1 X 4.0 sqmm run with proper colour code as per IE rules measured in one unit) 74 Supply and fixing in repair modular Switch6 Amps single pole, one waycomplete all as specified and directed. 75 Supply and fixing in repair Modular Socket outlet, multi purpose, 5 Pin 6 Amps flush typecomplete all as specified and directed. 76 Supply and fixing in repair Modular Socket outlet, multi purpose, 6 pin 16 Amps universal socketcomplete all as specified and directed. 77 Supply and fixing in repairModularSwitch 16 Amps single pole, one waycomplete all as specified and directed. 78 Supply and fixing in repairmodular fan regulator of four step type compatible with BLDC fan complete all as specified and directed. 79 Supply and fixing in repair white/colour finished single mounting modular plates with inner & outer coversuitable for housing modular accessories suitable for one module box complete all as specified and directed. 80 All as per item no 79 above but suitablefor 2 modules 81 All as per item no 79 above but suitablefor 3 modules 82 All as per item no 79 above but suitablefor 4 modules 83 All as per item no 79 above but suitablefor 6 modules 84 All as per item no 79 above but suitablefor 8 modules 85 All as per item no 79 above but suitablefor 12 modules 86 S&F Single pole and neutral enclosure 240 volts with a two pin and earth plug and socket complete with one single pole MCB 20 Amps complete all as specified and directed. 87 S & F ceiling rose 3 terminal PVC/polycarbonate isolated body type with necessary fittings complete all as specified and directed. 88 Supply, laying, jointing and testing alluminium unarmoured cable 1100V grade 10 sqmm 4 core in casing caping/ through saddle on wall complete all as specified and directed. 89 Supply, laying, jointing and testing alluminium unarmoured cable 1100V grade 6 sqmm 4 core in casing caping/ through saddle on wall complete all as specified and as directed. 90 M&L for Sub main wiringPVC insulated PVC unsheathed electric FRLS cable 1100V grade single core having multi stranded copper conductor single phase of size 4.0 Sqmm nominal cross sectional area ( for L & N) & including non metallic rigid PVC conduit ISI marked medium gradewith all conduit accessories in concealed wiring system by cutting/chesing of wall and making good disturbed surface of wall with cement mortar and existing colour painting after fixing of conduit & 4.0 sqmm green PVC insulated unsheathed copper conductor as a earth wire connected to earth dolly by providing lugs complete all as specified and as directed. (Note : wiring with 2 X 4.0 sqmm +1 X 4.0 sqmm run with proper colour code as per IE rules measured in one unit ) . 91 Supply and fixing double door VTPN DBs 415 volts rated voltage, 8 wayof powder coated DBs suitable for 125 AMps MCCB fitted with bus bar 450 A rated capacity,Neutral link,Earth bar and Din ral & DBs will be fitted concealed on wall / surface as per site requirement complete all as specified and directed. 92 Supply and fixing double door SPN DBs 240 volts rated voltage, 12 wayof powder coated DBs suitable for MCBs fitted with bus bar 200 A rated capacity,Neutral link,Earth bar and Din ral & DBs will be fitted concealed in wall / surface as per site requirement complete all as specified and directed. 93 Supply and fixing double door SPN DBs 240 volts rated voltage, 8 wayof powder coated DBs suitable for MCBs fitted with bus bar 200 A rated capacity,Neutral link,Earth bar and Din ral & DBs will be fitted concealed in wall / surface as per site required complete all as specified and directed. 94 Supply and fixing MCCB 125 amps 10 KA, C-series, 415 Voltincluding connection with suitable size aluminium / copper lugs complete all as specified and directed. 95 Supply and fixingMCB SPN 240 volts 40-63 Amps, 10 KA breaking capacity,C type including connection with suitable size aluminium / copper lugs complete all as specified and directed. 96 Supply and fixingMCB SP 240 volts 6 to 32 Amps, 10 KA breaking capacity,C type including connection with suitable size aluminium / copper lugs complete all as specified and directed. 97 Supply, laying, jointing & testing in trenches or passing through pipe, 1100 volts grade, XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured LT electric power under ground cables/ wall mounted by clip or concelledby cutting/chesing of wall and making good disturbed surface of wall with cement mortar and existing colour painting after fixing, heavy duty with aluminium conductor of cross sectional area 70 sqmm 3.5 core with all fixing & connecting accessories such as Alluminium cable lugs, cable gland, nut, bolts, washer, clamp etc complete as specified and as directed. 98 Excavation in trenches, not exceeding1.5 m wide and not exceeding 1.5 m in depth, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes,laying of cables etc. not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed. 99 Removal of surplus excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed. 100 S &F for 50 mm dia GI pipe light grade ISI marked including fittings such as bends, tees, sockets etc fixed on wall/pole or laid in trenches under road crossing/hardstandingincluding taking down existing pipe complete all as specified and directed. 101 M&L Sand cushioning with dry local sand for cable protecting under ground cable (8 cm before laying the cable and 15 cm after laying the cable) in trenches including punning the sand upto 18 cm thick and consolidated complete all as specified and directed.NOTE :Punned thickness only shall be measured for payment. 102 Supply and laying dry well burnt locally available old sub classBbricks laid flat with width equal to the length of whole bricks over cable as cable protection complete all as spcified and directed. 103 Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm each complete all as specified and directed. 104 M&Lfor Rigid non metallic PVC casing capingISI marked, medium grade,not less than 100 mm base size inclusive of all fitting such as tees,bends. Junction boxes, elbows saddleshooks,couples and lock outs etc and fixed on surface mounted complete and making good disturbedsurfaces in repairs all as directed. 105 Supply and fixing LED light fitting for bldg security lighting energy saving & environmental friendly long life versatile pressure die-cast housing with individual high power LED as light source and lens embedded PC cover of capacity 35 watt 240 volts AC 50 Hz , IK 07 and IP 66 protection suitable for fitted with 40/25 mm dia GI pipe brackets complete all as specified and directed.
