Tender For Certain Misc B/R Repair Works For Otm Accn And Md Accn At Pashan Area Under Ge(I) Rnd Pashan, Pune; 1 Taking down existing roof treatment in any position with bitumenous felt includingcement plaster of any thicknessin roofs (other than ground floors), beams, chajjas, staircase etc and removing the rubbish to a distance exceeding250m and n. exc 500m deposited where directed Complete all as specified and as directed by Engineer-in-Charge. 2 Dismantling of exisiting old padding concrete of any thickness over the RCC slab other thanbeams, chajjas, staircase etc by chipping of with proper tools viz chiesel and with applying reasonable force so as to avoid any damages to exiting RCC roof slab, Complete all as specified and as directed by Engineer-in-Charge. 3 Material and labour for cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate as in levelling / padding course on roof slab, chajjas, projections on similar surfaces existing with slope, kerbs, rounded or chamfered edges, making the surface even and smooth without using extra cement, including using liquid water proofing compound, Complete all as specified and as directed by Engineer-in-Charge. Note: supply ofIntegral water proofing compound will measured and paid seperately. 4 Material and labour for 10mm thick cement plaster in CM 1:4 over PCC (while concrete is green) using approved liquid water proofing (Note: supply of liquid water proofing compound will measured and paid seperately and dosage shall be as per manufacturer instructions) Complete all as specified and as directed by Engineer-in-Charge. 5 Supply only liquid water proofing compoud Complete all as specified and as directed by Engineer-in-Charge. 6 Material and labourfor APP based polymeric membrane weighing not less than 3.0 kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than160gms/Sqm) laid over primed surface including bituminous primer conforming to IS-3384 applied @ 0.3 ltr/sqm completeall as specified and directed. Note: (i) The wrok shall be executed through authorised applicator of manufacturer (iii) The contractor has to submit guarantee for 10 yearsFour course roof treatment consists of as under :-(a) Applying one coat of bituminous primer conforming to IS-3384 @ 0.30 Ltr per sqm.(b) Laying of APP based membrane as specified thickness and weight.(c) Applying one coat of bitumen grade 85/25 @ 1.2 Kg/Sqm.(d) Applying two coat of aluminium paint @ 200ml/sqm 7 Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, Complete all as specified and as directed by Engineer-in-Charge. 8 Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and jointed in cement mortar or bedding, Complete all as specified and as directed by Engineer-in-Charge. 9 Demolition of Cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level), Complete all as specified and as directed by Engineer-in-Charge. 10 Material and labour for 25mm thick Cement concrete1:2:4 type B-1,( using 20mm graded crushed stone aggregate) as in sub base of flooring, Complete all as specified and as directed by Engineer-in-Charge. 11 Material and labour for 75 mm thick Cement concrete type C1, 1:3:6 (using 20 mm gradedstone aggregate) asin plinth protection/ hard standing path etc finishing the surfaceeven and smooth without using extra cement, Complete all as specified and as directed by Engineer-in-Charge. 12 Material and labour for coloured Non Skid ceramic tiles 7 mm to 8mm thick (square / rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in cement mortar 1 : 6, Complete all as specified and as directed by Engineer-in-Charge. 13 Material and labour for coloured Non Skid ceramic tiles 7 to 8mm thick(square / rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in cement mortar 1 : 4, Complete all as specified and as directed by Engineer-in-Charge. 14 Material and labour for double charge Vitrified ceramic tiles 9 to 10mm thick (square/rectangular) area of each tile notexceeding 0.36 sqm, as in floors,etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in cement mortar 1 : 4, Complete all as specified and as directed by Engineer-in-Charge. 15 Material and labour for Vitrified ceramic tiles 9 to 10mm thick (square/rectangular) area of each tile notexceeding 0.36 sqm, as in skirtings, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including rendering 10 mm thick in cement mortar 1 :3 as backing coat, Complete all as specified and as directed by Engineer-in-Charge. 16 Material and labour for Light coloured Glazed ceramic tiles in vertical surface as in skirting or dado 300 mm x 450 mm x 7 mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including rendering 10 mm thick in cement mortar 1 :3 as backing coat, Complete all as specified and as directed by Engineer-in-Charge. 17 Material and labour for20mm thick granite (of any type) work (Table rubbed and polished) in steps, jambs, pillars, windows cills, cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admisture of pigment to match with shade of granite laid over and including screed bed of 15mm thick in CM 1:4, Complete all as specified and as directed by Engineer-in-Charge. 18 Material and labour for Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations, Complete all as specified and as directed by Engineer-in-Charge. 19 Material and labour for Drilling holes on granite, cudappa or trap stone for bolts. Pipes, etc. n.exc 25 mm dia, Complete all as specified and as directed by Engineer-in-Charge. 20 Material and labour for Machine cut cudappa stone slab flooring 20-25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid over and including screed bed of 15mm thick in CM 1:4, Complete all as specified and as directed by Engineer-in-Charge. 21 Material and labour for 20mm thick Granite (of any type) tiles machine cut in skirting/dado laid over 10 mm thick backing coat in CM 1:3 jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing, Complete all as specified and as directed by Engineer-in-Charge. 22 Demolition of cement concreteabove ground floorsexc 15cm thickness as in sunken floors or in similar works, Complete all as specified and as directed by Engineer-in-Charge. 23 Material and labour for water proofing treatment of sunken floor by applying(a)15mm thick plaster in cement mortar 1:4 with WPC (b) application of cement slurry mixed with and including acrylic based polymer modified cementitious composite compound coating in two layers as per direction of Engineer inCharge. (C) Over and above200 micron thick polymer film should be pasted with the help of adhesive after treatment, Complete all as specified and as directed by Engineer-in-Charge.Note: (i) Make :- Dr Fixit, Asian paints, Fosroc and M/S Sikka.(ii) The work shall be executed only through authorised applicator of manufacturer. 24 Material and labour for Cement concrete in foundations, filling and mass-concrete, 1:5:10 Type E2 (Using 40mm Graded crushed stone agrregate) as in sunken floors, Complete all as specified and as directed by Engineer-in-Charge. 25 Material and labour for 40mm thick Cement concrete 1:2:4 Type B1 (using 20mm graded crushed stone aggregate) as in floor, Complete all as specified and as directed by Engineer-in-Charge. 26 S&F 75mm PVC (SWR) floor trap plain with grating including jointing with solvent cement, Complete all as specified and as directed by Engineer-in-Charge. 27 Supply and fix in repairs PVC connections 15mm size with PTMT nuts of length 600mm, Complete all as specified and as directed by Engineer-in-Charge. 28 Supply and fix in repairs Vitreous China wash basin, white, flat back, size 550mmx400mm excluding taps, waste chain and plug and porcelain stopperfixing on existing brackets,including supply and fixing of flexible waste outlet pipe of 32 mm dia of required length, Complete all as specified and as directed by Engineer-in-Charge. 29 Supply and fix 32mm borewaste coupling of PTMT (half or full threaded) Minimum weight45gms, suitable for vitreous china wash basin, Complete all as specified and as directed by Engineer-in-Charge. 30 Supply and fix in repairs 15mm borePillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot or `Cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed (Min wt 15mm bore- 675 grams), Complete all as specified and as directed by Engineer-in-Charge. 31 Supply and fix in repairs10Litres capacitylow level PVC flushing cistern valveless, syphonic action type, , white, with inlet, ball valve, float and handle including brackets, Complete all as specified and as directed by Engineer-in-Charge. 32 Supply and fix in repairs Vitreous china wash down water closet pan (pedestal pattern), white including fixing bolts (excludingflushing cistern and flush pipe) including pan seat cover, Complete all as specified and as directed by Engineer-in-Charge. 33 Supply and fix in repairs Vitreous China squatting pan, `Orissa pattern, size 580 mm x440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including provision of cement concrete bedding, Complete all as specified and as directed by Engineer-in-Charge. 34 Supply and fix in repair 15mm bore Fancy type long body chromium plated Bib taps, cast copper alloy fancy type, screwed down, screwed for iron pipe or for brass ferrule (minimum weight 550 grams), Complete all as specified and as directed by Engineer-in-Charge. 35 Supply and fix in repairs 15mm bore chromium plated Angle cock, cast copper alloy screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe orfor unions(minimum weight400 grams), Complete all as specified and as directed by Engineer-in-Charge. 36 Supply and fix in repairs 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed, Complete all as specified and as directed by Engineer-in-Charge. 37 Supply and fix in repairssinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, including PTMT waste coupling (half or full treaded) (Min wt 40mm bore - 60 grams) and PVC waste pipe 32 mm dia, Complete all as specified and as directed by Engineer-in-Charge. 38 Supply and fix in repaires sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size495mm x 420mm bowl size 410mm x 330mm x 160mm, including PTMT waste coupling (half or full treaded) (Min wt 40mm bore - 60 grams) and PVC waste pipe 32 mm dia, Complete all as specified and as directed by Engineer-in-Charge. 39 Supply and fix in repairs bathroom mirror 450mm x 600mm bevelled edge mirror of selected quality glass mounted on 6mm thick PVC board and fixing with plastic plugs by means of brass srcews etc, Complete all as specified and as directed by Engineer-in-Charge. 40 Supply and fix in repairs soap dish stainless steel, Complete all as specified and as directed by Engineer-in-Charge.Note : Model shall be as directed by Engr-in-Charge. 41 Supply and fix in repairs 2 in 1 mixture valve of brass chromium plated, 15mm bore, screwed down, screwed for iron pipe or for brass ferule and fixed, Complete all as specified and as directed by Engineer-in-Charge.Note : Model shall be as directed by Engr-in-Charge 42 Supply and fix in repairsswivel shower chromium plated with shower arm 15 mm size, 195 mm long with bend of 45ºwith flange fixed to 15 mm dia GI tubing, shower roses with or without swivel joints,125mm size, including fixing to steel pipe or union, Complete all as specified and as directed by Engineer-in-Charge. 43 Supply and fixin repairs toilet paper holder of chromium plated fixed to walls with and including chromium plated brass screws, Complete all as specified and as directed by Engineer-in-Charge. 44 Supply and fix in repairs two way bib cock of brass chromium plated, 15mm bore, screwed down, screwed for iron pipe or for brass ferule and fixed Complete all as specified and as directed by Engineer-in-Charge. 45 Supply and fix in repairs 1.2metre long chromium plated health faucet including holder fixed to wall, Complete all as specified and as directed by Engineer-in-Charge. 46 Dismantaling water tanksexceeding250 litresand not exceeding500 litres capacity Complete all as specified and as directed by Engineer-in-Charge. 47 Dismantaling water tanksexceeding 500 but not exceeding 1000 litres capacity Complete all as specified and as directed by Engineer-in-Charge. 48 Supply and fix 500 Litres Rotational moulded polyethylene water storage tanks triple layered(cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I, Complete all as specified and as directed by Engineer-in-Charge. 49 Supply and fix 1000 Litres ISI embosed Rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I, Complete all as specified and as directed by Engineer-in-Charge. 50 Taking out old chocked 20 mm bore GI pipe and connections, including cleaning for refixing or removal to storefrom trenches, walls, ceilings, floors etc complete all as specfied and directed by engr-in-Charge. :- 51 All as per item No.51 above but 15 mm bore Complete all as specified and as directed by Engineer-in-Charge. 52 Supply and fix 20 mm bore GI tubing medium grade with and includingnecessary fittings complete to walls and ceilings or laid in floorsComplete all as specified and as directed by Engineer-in-Charge. 53 All as per item No.52 above but 15 mm bore 54 Material and Labour forCutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth as in stone / concrete block walls, Complete all as specified and as directed by Engineer-in-Charge. 55 Supply and Fix in repairs 40 mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm²fixed complete to walls, ceilings or in floors etc, including all pipe fittings, Complete all as specified and as directed by Engineer-in-Charge. 56 Taking down rain water pipes(any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc, including cleaning or refixing or removal to store, Complete all as specified and as directed by Engineer-in-Charge. 57 Supply and fix 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, Complete all as specified and as directed by Engineer-in-Charge. 58 Supply and fix110 mm bore PVC (SWR) bends of any radius, Complete all as specified and as directed by Engineer-in-Charge. 59 S&Ffor 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joint fixed to walls, Complete all as specified and as directed by Engineer-in-Charge. 60 S&Ffor 75 mm bore PVC (SWR) bends of any radius, Complete all as specified and as directed by Engineer-in-Charge. 61 Taking downchowkats or frames (without taking of shutters from the frames) not exceeding 1.5 Sqm each, Complete all as specified and as directed by Engineer-in-Charge. 62 Taking down shutter of size exceeding 1 Sqm butnot exceeding 2 Sqm each, Complete all as specified and as directed by Engineer-in-Charge. 63 Taking down existing chowkats or frames (without taking of shutters from the frame) exceeding 1.5sqm but not exceeding 4 sqm, Complete all as specified and as directed by Engineer-in-Charge. 64 Supply and fix factory madeSoild PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, suppling and fixing in opening as per specification and drawing, Complete all as specified and as directed by Engineer-in-Charge. 65 Supply and fix Factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heatmoulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail and bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement, Complete all as specified and as directed by Engineer-in-Charge. 66 Supply and fix extruded aluminium alloy handles, fabricated type anodised 125 mm size, Complete all as specified and as directed by Engineer-in-Charge. 67 Supply and fix 125 mm long aluminium anodised barrel tower bolts of extruded section, Complete all as specified and as directed by Engineer-in-Charge. 68 Supply and fix 100 mm long MS butt hinges medium weight cold rolled welded to steel frame /fixed to wooden and PVC frame with suitable screws, Complete all as specified and as directed by Engineer-in-Charge. 69 S&F Mild steel flat iron as in hold fasts or similar small articles conforming to Fe-290 Gde E-165, Complete all as specified and as directed by Engineer-in-Charge. 70 Supply and fix 35mm thick factory made Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated (II class hard wood), Complete all as specified and as directed by Engineer-in-Charge. 71 Supply and fix factory made 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, Complete all as specified and as directed by Engineer-in-Charge. 72 Supply and fix 35mm thick II class hardwood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a) supplied and fitted to chowkats, Complete all as specified and as directed by Engineer-in-Charge. 73 M&L for preparation of new wooden surfaces of width or girth exc 10 cm and applying two coats of synthetic enamel paint over a coat of pink primer, Complete all as specified and as directed by Engineer-in-Charge. 74 Supply and fix300mm long aluminum alloy anodised sliding door bolt with hasp and stapple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section, Complete all as specified and as directed by Engineer-in-Charge. 75 Supply and fix extruded aluminium alloy handles, fabricated type anodised 150 mm size, Complete all as specified and as directed by Engineer-in-Charge. 76 Supply and fix 150 mm long aluminium anodised barrel tower bolts of extruded section, Complete all as specified and as directed by Engineer-in-Charge. 77 Supply and fix 100 mm long Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, Complete all as specified and as directed by Engineer-in-Charge. 78 Supply and fix Aluminium powder coated sliding windows three track consists of 03 Nos of shutters i.e 02 Nos of Glazed shutters and 01 No of gauzed shutter with size of sections of styles and rails complete all as specified anddirected by Engineer-in-ChhargeNote:(i) All aluminium section including galzing clips, snap beading, joining cleats, rubber packing screws etc as required are deemed to be including in the rate quoted.(ii)Thickness of powder coating minimum 50 micron.(iii) Glass & wire cloth shall be measured and paid separetely under respective items. 79 Material and labour for Aluminium powder coated ventilators shutters partly fix and partly lowered of aluminium section designed DG-2762 (40 mm x 32 mm x1.5 mm thick) (wt 0.668 kg/mtr)frame and DG-2763 and middle section of designed DG-2763 (40 mm x 32 mm x 1.5 mm thick)(wt 0.654 kg/mtr), middle section DG-2546 (17.27 mm x 17.15 mm x 1.22 mm thick) (wt 0.124 kg/mtr) including 5 mm thick pinheaded figured glass louvers with blades of 100 mm heavy duty including with aluminium lever handle fixed panel shall be provided with 5 mm thick pin headed figured glass including all necessary rubber packing, anodized aluminium snap beading fixed with minimum 6 Nos of suitable size galvanised screws with PVC plug etc complete all as specified and directed. 80 Supply and Fix 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square in n.exc 0.5 sq.m in each pane, Complete all as specified and as directed by Engineer-in-Charge. 81 S&FStainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, Complete all as specified and as directed by Engineer-in-Charge. 82 Dismantling wrought iron or mild steel work and elevated iron loft tank of any description not otherwise provided for, Complete all as specified and as directed by Engineer-in-Charge. 83 Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, Complete all as specified and as directed by Engineer-in-Charge. 84 Supply and fix Roof trusses , trussed, purlins, post, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats Fe-410 W (Gde-E-250) quality A complete all as specified and directed.Complete all as specified and as directed by Engineer-in-Charge. 85 Supply and fixing mild steel framed work such as grills, gratings, etc, with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters:walk ways, railing, framed work of water tanks and similar work conforming to Fe 290 Gde E-165, Complete all as specified and as directed by Engineer-in-Charge. 86 Supply and fixing Pre-painted galvalume aluminium zince coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws, Complete all as specified and as directed by Engineer-in-Charge. 87 Preparation of new or previosly untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer, Complete all as specified and as directed by Engineer-in-Charge. 88 Dismantling boarding of any description, fixed in any position, Complete all as specified and as directed by Engineer-in-Charge. 89 Material and labour for 18/19 mm thick Prelaminated particle board, exterior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work / steel frame, Complete all as specified and as directed by Engineer-in-Charge. 90 Hacking out old broken glass (any thickness, size, quality or description) frommetal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones and Supply and fix 4mm thick Sheet glass, ordinary quality, in squares not exceeding 0.5 Sqm each pane,Complete all as specified and as directed by Engineer-in-Charge. 91 Supply and fix in repairs 20mm bore stainless steel Gde 304 curtain rodsComplete all as specified and as directed by Engineer-in-Charge. 92 Supply and fix in repairs stainless steel fancy type brackets suitable for 20mm dia curtain rodsComplete all as specified and as directed by Engineer-in-Charge. 93 Supply & Fix in repairs 200mm long aluminium barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed, Complete all as specified and as directed by Engineer-in-Charge. 94 Supply & Fix in repairs 300mm long aluminium, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled of drawn brass bolts and fixed, Complete all as specified and as directed by Engineer-in-Charge. 95 Supply & Fix in repairs 125mm long Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-12, Complete all as specified and as directed by Engineer-in-Charge. 96 Supply & Fix in repairs 150mm long Extruded aluminium handles, fabricated type polished, Complete all as specified and as directed by Engineer-in-Charge. 97 Demolition of brick work/ stone masonry/ PCC block masonry built in cement mortar or cement lime mortar including all quoins, pillars, arches etc, but excluding ashlar facings dressed stone work and precast concrete articles, Complete all as specified and as directed by Engineer-in-Charge. 98 Material and labour forPCC block masonry with solid blocks, exc 10 cm in width and setting CM 1:6 precast cement concrete block of type C-1 with 1:3:6 (using 20 mm graded stone aggregate), Complete all as specified and as directed by Engineer-in-Charge. 99 Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc, Complete all as specified and as directed by Engineer-in-Charge. 100 Material and Labour for Rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 using WPC, Complete all as specified and as directed by Engineer-in-Charge. (wpc will be measured and paid seprately) 101 Material and Labour for Rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6, Complete all as specified and as directed by Engineer-in-Charge. 102 Material and Labour for Rendering 20mm thick on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing in cement mortar 1:4 using WPC, Complete all as specified and as directed by Engineer-in-Charge. (wpc will be measured and paid seprately) 103 Material and Labour for Rendering on ceiling, 5mm thick on fair faces of concrete surfaces in cement mortar 1:3, Complete all as specified and as directed by Engineer-in-Charge. 104 Material and Labour for preparation of newly plastered ceiling surface and applying three coats of white wash, Complete all as specified and as directed by Engineer-in-Charge. 105 Material and labour for preparation of newly plastered wall surface and applying two coats oil bound distemperover a coat of 1mm thick wall interior wall care putty and a coat of primer, Complete all as specified and as directed by Engineer-in-Charge. 106 Material and Labour for preparation of newly plastered wall surface and applying two coats of acrylic weather proof paintover and including a coat of acrylic primer, Complete all as specified and as directed by Engineer-in-Charge. 107 Material and labour for disconnecting existing PVC water tanks, setting aside (or lowering if required) for repairs, cleaning and removing all scale and dirt etc from tanks and from mouthts of circulating pipes etc and hoisting if required reconnecting and refixing in position of capacity exceeding 250 ltrs and n exc 500 ltrs, Complete all as specified and as directed by Engineer-in-Charge. 108 All as per Item No 107 here in before but of 1000 litrs capacity Complete all as specified and as directed. 109 Supply and fix in repairs 20mm Ball brass valves,high pressure,with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, Complete all as specified and as directed by Engineer-in-Charge. 110 Taking down and refixing in same positionShutters of any description exceeding1 sqm but not exceeding 2sqm each, including easing and repair works , complete all as specified and directed. 111 Supply & fix 1.80M with 4 pipes pully operated clothes drying system consisiting of anodized aluminium pipes each of outer dia 22mm and inner dia 19.8mm. Pulleys madeup of Delrin with rope guide mounted on channel pair of length 24 inches (distance between 2 pipes is adjustable), locking system to hide rope knot channel to be mounted or fixed with self-tapping screws provided in kit, rope will be polyster braided undyed of 3.5+/0.5mm dia complete all as specified and directed. 112 Supply and fix in repair stainless steel plate rack of size 600mm x 750mm made out of 1mm thick stainless steel sheet of grade 304 fixed all as per manufacturers instructions, Complete all as specified and as directed by Engineer-in-Charge.
