Tender For Development Of Tb Ward At Mgims/Khs, Sevagram; 1 Civil Works 2 Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up toa distance of50 m. beyond the building areaand stacking andspreadingasdirected,dewatering,preparingthebedfor thefoundationandnecessarybackfilling,ramming,watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) ( Upto 1.5 M Depth) 3 Excavation for foundation in earth, soils of all types, sand,gravel and soft murum, including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5m to 3.0m) 4 Filling in plinth and floors with approved excavated material in 15cm. to 20cm. layers including watering and compacting etc. complete. 5 Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete. (Including Rubble soling quantity ) 6 Providingpreconstructionalantitermite treatmentas perI.S. 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percentofchlorophyrifospersquaremeterofsurfacearea covering 10 years guarantee on bond paper. 7 Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishingifrequiredandcuringcomplete,withfullyautomatic microprocessorbasedPLCwithSCADAenabledreversible DrumTypemixer/concreteBatchmixplant(Panmixer)etc. complete.With natural sand/V.S.I. quality Artificial Sand 8 Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, plywood/steel formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand ( For Grade Slab Work). 9 Providing and laying 125 micron Low Density Polyethylene (LDPE) sheet confirming to IS 3395 : 1997 below concrete pavement including all materials and labour complete. 10 Providing and laying in situ/Ready Mixcement concreteM-20 oftrap/granite/quartzite/gneiss metalforR.C.C.work in foundationslikeraft,strip foundations,grillage and Footingsof R.C.C.columns and steel stanchionsetc. including bailing out water,formwork,laying/pumping coverblocks,compaction andcuringrougheningthesurfaceifspecialfinishistobe provided(Excludingreinforcementandstructuralsteel)etc. complete, with fully automatic micro processor based PLC with SCADAenabledreversibleDrumTypemixer/concreteBatch mixplant(Panmixer)etc.complete.Withnaturalsand/V.S.I. quality Artificial Sand 11 Providing and laying Cast in situ/Ready Mix cement concrete M 20 of trap / granite /quartzite/ gneiss metal forR.C.C. columns asperdetaileddesignsanddrawingorasdirectedincluding centering,formwork,coverblocks,laying/pumping, compactionfinishingtheformedsurfaceswithcementmortar 1:3 of sufficient minimum thickness to give a smooth and even surfaceorrougheningifspecialfinishistobeprovidedand curingetc.complete,(Excludingreinforcementandstructural steel).with fully automatic micro processor based PLC with SCADAenabledreversibleDrumTypemixer/concreteBatch mixplant(Panmixer)etc.complete.Withnaturalsand/V.S.I. quality Artificial Sand 12 Providing and laying Cast in situ/Ready Mix cement concrete M 20oftrap/granite/quartzite/gneissmetalforR.C.C.beams and lintels as per detailed designs and drawings or as directed includingcentering,formwork,coverblocks,laying/pumping, compactionand roughening the surface if special finish is to be providedandcuringetc.complete.(Excludingreinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand 13 Providing and laying Cast in situ/Ready Mix cement concrete M 20 of trap/granite/ quartzite/gneiss metal for R.C.C slabs & landings as per detailed designs & drawings including centering, formwork, cover blocks, laying / pumping, compaction finishingtheformedsurfaceswithcementmortar 1:3 of sufficient minimum thickness to give a smooth and even surfaceorrougheningifspecialfinishistobeprovidedand curingetc.complete,(Excludingreinforcementandstructural steel).with fully automatic micro processor based PLC with SCADAenabledreversibleDrumTypemixer/concreteBatch mixplant(Panmixer)etc.complete.Withnaturalsand/V.S.I. quality Artificial Sand 14 Providing and laying Cast in situ/Ready Mix cement concrete M 20 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as perdetaileddesignanddrawingsincludingcentering, formwork,coverblockscompacting,curing,finishingand rougheningthesurfaceifspecialfinishistobeprovidedand curing complete.(Excluding reinforcementand structural steel).with fully automatic micro processor based PLC with SCADAenabledreversibleDrumTypemixer/concreteBatch mixplant(Panmixer)etc.complete.Withnaturalsand/V.S.I. quality Artificial Sand 15 Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs,beamscolumns,canopies,staircase,newels,chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawingsandschedules.includingcutting,bending,hooking the bars,binding with wires or tack welding and supporting as required complete. 16 Providing secondclass Burnt Brick masonry with conventional / I.S. type bricks in cement mortar 1:6 in superstructure including strikingjoints,rakingoutjoints,wateringandscaffoldingetc. Complete (230mm Brickwork) 17 Providing secondclass Burnt Brick masonry with conventional/ I.S.typebricksincementmortar1:4inhalfbrickthickwall including mild steel longitudinal reinforcement of 2 bars of 6 mm diameter / 2 hoop iron strips 25 mm X 1.6 mm placedat every thirdcourse,properlybentandbondedatendsscaffolding, racking out joints and watering etc. complete. (Wall thickness is 100 MM) 18 Providingcementbasedwaterproofingtreatmenttoterraces (Indian water proofing or alike) with brick bats laid in required slopetodrainthewaterforanyspanaftercleaningthebase surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats onbottom layer inC.M.1:5 admixedwith approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofingcompoundandfinallytopfinishingwithaverage20 mm. thick layers ofsame mortar added with jutefiberat1 Kg perbagincludingfinishingthesurfacesmoothwithcement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300mm x 300 mm. making the junctions at the parapetrounded and tapered top forrequiredheight,withdripmouldatthejunctionofplaster andparapetandcuringandcovering10yearsGuarantee againstleakproofnessonCourtfeestamppaperofRs.500/- including ponding test etc. complete. (Qty including Floor & Wall Area) 19 Providing internal cement plaster 12mm thick in single coat in cement mortar 1:5 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. (Ceiling also considered) 20 Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receivethesandfacedtreatment6to8mmthickincement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. (Ext Plaster) 21 Providing and fixing chicken mesh of22gauge, with about 30 cm. width at the junction of R.C.C members and brick work, of approved quality including fixing mesh in position by necessary drillinginconcrete/B.B.masonryandortyingbybindingwire etc. complete. 22 Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622- 2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete. a) Flooring (Makes Kajaria/Nitco/RAK) 23 Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622- 2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete. b Dado (Makes Kajaria/Nitco/RAK) 24 Providing and laying Antiskid Ceramic tiles of approved quality of size 30 cm x 30 cm and confirming to IS15622-2006 (Group-BIIA) for antiskid flooring in the required position laid on a bed of 1:4 cement mortar, including cement float, filling joint with cement slurry, cleaning, curing etc. complete. Toilet Floor (Makes Kajaria/Nitco/RAK) 25 Providing and laying ceramic tiles having size 30 cm. x 60 cm. confirming to corresponding I.S.for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete. (Toilet Dado) (Makes Kajaria/Nitco/RAK) 26 Providing and fixing heavy duty inter locking concrete Coloured paving blocks of 40 mm thickness of having a strength of 200 kg/Sq.cm. of approved quality and shape on a bed of crushed sand of 25 to 30 mm thick including skirting joints and cleaning etc. complete. 27 Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete. 28 Providingandapplyingtwocoatsofexterior weathershield paint (Ace/ Apex)of approved manufacture and of approved colour to the plasteredsurfacesincludingcleaning,preparingtheplaster surface,applyingprimercoat, scaffoldingifnecessary,and watering the surface for two days etc complete. NOTE: ForItemNo.15to18priorapprovalofSuperintending Engineer will be necessary (Makes Asian / Berger) 29 Providing and applying impression 24 carrat Luxury paint of approved make & approved brand Emulsion paint to interior walls and ceilings of approved quality,colour and shade to newsurface in two coats, including sub surface prparation by Acrylic putty and Acrylic primer coats including scaffolding, preparing the surface. etc. complete (Low VOC). (Makes Asian/ Berger) 30 Providing and fixing M40 grade thick vibrated pull cast or similar type concreteframe with chamfer conforming toI.S.65241983 having6mmdia.bars3Nos.Andstirrups@250mmc/cand fixing in wall with 6 Nos of hold fast of 12 mm dia bars 500 mm long including primer and oil painting etc, complete) frame size 60 mm x 100 mm . 31 Providing and fixing in position (as per 1868 / 1982) Aluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90mmatweight0.637kg/Rmt.withwindowframebottom track section 92 x 31.75 x 1.30 mm at weight 1.070 kg/Rmt.. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 kg/Rmt. and handle and top section 40 x 18 x 1.25 mm at weight o.417 kg/Rmt. Asperdetailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures andfasteningssuch asrollerbearingin nylon castingand self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminiummosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With colour Anodising without box 32 Providing and fixing mild steel grill work for windows, ventilators etc.20kg/sqmasperdrawingincludingfixtures,necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete. 33 Providing and fixing solid core flush door shutter in single leaf 32 mmthickdecorativetypeofexteriorgradeasperdetailed drawings approved face laminate 1mm thick on both faces or as directed, all necessary beads, mouldings and lipping, wroughtironholdfasts,chromiumplatedfixturesand fastenings, with L drops, chromium plated handles on both sides, and finishing with colour polish etc. complete. 34 Providing and fixing mild steel grill gate as per the detailed drawing including hinges, locking arrangements and painting in three coats of oil paint of approved colour and shade etc.complete.(weight 18 kg. to 20 kg. Per Sq.m.) Spec.No.: As directed by Engineer- in-charge. 35 Providing and fixing colour coated Zincalume ( R ) AZ150 ( min 150 gms/sq.mt. total on each side) profiled sheets for roofing. The feed material is manufactured out of nominal 0.45 mm Base Metal Thickness (BMT) (0.5 mm TCT ), Hi-strength steel with min.550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% aluminium 43.4% zinc 1.6% silicon) with COLORBOND ( R ) steel quality super durable polyester paint coat ( with inorganic pigment). The paint shall have a total coating thickness of nominal 35 um, comprising of nominal 25 um exterior coat on top surface and nominal 10 um reverse coat on back surface. Profile sheet shall have nom. 950-1050mm effective cover width and nominal 25-30 mm deep ribs with subtle square fluting in the five pan at nominal 180-250 mm center-to-center. The end rib shall be designed for anticapillary groove. and return leg. The feed material should have coil manufacturers product details marked a regular interval. Including fasteners with min. fastened with min. 25 um Zinc-Tin alloy coated, Hex head, self-drilling screw etc. complete.(weight of profile 4.52 kg/sqm) 36 Providing and fabricating structural steel work in rolled sections, fixed with connecting plates or angle cleats in main and cross beams, hip and jack rafters, purlins connecting to truss members and the like, as per detailed designs and drawing or as directed including cutting, fabricating, hoisting, erecting, fixing in position, making riveted/ bolted/ welded connections and one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete. 37 Sliding Door- Providing and fixing a sliding door made of powder-coated extruded aluminum alloy frame (Grade 6063-T6 or equivalent) with a minimum profile size of 50mm x 38mm for shutters and 63mm x 38mm for the frame, having a wall thickness of 1.2 mm to 1.5 mm. The door shall be infilled with 6 mm to 8 mm thick phenolic resin bonded Bakelite sheet (Greenlam, Century Ply) in approved color and finish. The door shall operate on heavy-duty nylon rollers with stainless steel ball bearings fixed in top and bottom sliding tracks (Ebco, Hafele, or Hettich) with integrated stoppers. The locking system shall be a surface-mounted or mortise-type sliding door lock with key and knob, using anti-corrosive SS/brass material from brands like Godrej. D-type or recessed pull handles in SS 304 or anodized aluminum shall be provided with a satin or chrome finish. All accessories shall be rustproof and installed using SS screws with PVC grommets. The door shall be installed plumb and level, with joints sealed using weatherproof silicone sealant, ensuring smooth sliding and secure locking. All materials should conform to relevant IS codes and be free from any surface defects. 38 Door Breaking for 230mm thickwall and Shifting the material as instructed by Engineer, In-Charge including nessessary repairing with all finishing, cleaning etc complete. 39 Plumbing Works 40 Providing and fixing screw down 20 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete (Make: Jaquar / Kohler ) 41 Providing and fixing screw down 32 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete (Make: Jaquar / Kohler ) 42 Providing and fixing screw down 40 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete(Make: Jaquar / Kohler ) 43 Providing and fixing screw down 50 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete (Make: Jaquar / Kohler ) 44 Providing and fixing white glazed earthenware Wash Hand Basin of 55cm. x 40 cm. size including cold water pillar tap/cold and hot water pillar tap brackets, rubber plugs and brass chain, stop tap and necessary pipe connections including P.V.C. waste pipe and trap up to the outside face of the wall. Making good the damaged surface, testing etc. complete.(Make: Jaquar / Kohler ) 45 Providing, laying and fixing P.V.C. pipe of 32mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete(Make: Paras / Supreme / Plasto) 46 Providing and fixing 75 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures andfitting such as bends, tees, single junctions, slotted vent, clamps etc.(Make: Paras / Supreme / Plasto) 47 Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and withnecessary fixtures andfitting such as bends, tees, single junctions, slotted vent, clamps etc.(Make: Paras / Supreme / Plasto) 48 Providing and fixing H.D.P container one piece moulded water tank made out of high density polythyler and built corrugated inclusive of delivery upto destination hoisting and fixing of accessories such as inlet, outlet overflow pipe inclusive of all tanks capacity between 200 to 1000 liters(Make: Paras / Supreme / Plasto) 49 Providing and fixing onwalls/ceiling/floor 20 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipeline if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete(Make: Paras / Supreme / Plasto) 50 Providing and fixing onwalls/ceiling/floor 32 mm dia. CPVC pipe with necessary fittings, remaking good the demolishe dportion etc. complete. Including removing existing pipeline if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete(Make: Paras / Supreme / Plasto) 51 Providing and fixing onwalls/ceiling/floor 40 mm dia. CPVC pipe with necessary fittings, remaking good the demolishe dportion etc. complete. Including removing existing pipeline if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete(Make: Paras / Supreme / Plasto) 52 Providing and fixing onwalls/ceiling/floor 50 mm dia. CPVC pipe with necessary fittings, remaking good the demolishe dportion etc. complete. Including removing existing pipeline if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete(Make: Paras / Supreme / Plasto) 53 Providing and fixing stainless steel sink of size 600 x 510 x 200mm incluidng coupling, outlet pipe, elbow and other necessary fitting, finishing etc. complete.(Make: Jaquar / Kohler / Cera) 54 Providing and fixing C.P. Angular stop clock with wall flange of approved make continental including necessary sockets/ union nut etc. complete(Make: Jaquar / Kohler ) 55 Providing and fixing C.P.Two way BIB cock of approved make continental including necessary sockets/union nut etc. complete(Make: Jaquar / Kohler ) 56 Providing and fixing C.P. wall mixer with provision for overhead shower with 115mm long bend pipe and wall flange of approved make including necessary sockets/union nutetc. complete.(Make: Jaquar / Kohler ) 57 Providing and fixing C.P. BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete(Make: Jaquar / Kohler ) 58 Providing and fixing European type wall-hung whitewater closet of approved make with push valve concealed type with cover plate 32mm size of approved make including soil pipe, vent pipe up to outside face of wall ,100mmdia. G.I. plug bend inlet pipeallfittings, cuttingand making good walls, floors etc. complete.(Make: Jaquar / Kohler ) 59 Providing and fixing P.V.C. Rainwater pipes of 110mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receivingrecess with P.V.C. plug, bend, necessary fittings, suchas, offsets, shoes, inluding fixing the pipe onwall using approved wooden cleats projecting 25 mm to 40 mm from face of wall fixing with clips of approved quality and number, filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C.or masonry blocks, including necessary scaffolding and maintenance for 3yrs for any leakages order is locations of pipes. All the P.V.C.fittings and additional 2 piece socket clips shall be got approved from engineer incharge etc. complete.(Make: Jaquar / Kohler ) 60 Providing and fixing 8 cm rigid PVC Nahani trap including PVC grating, bend, connecting piece of UPVC pipe up to the outside face of wall, making the good damaged surface and testing etc. complete (Prior approval of sample and brand by Ex. Engr. is necessary before use)(Make: Paras / Supreme / Plasto) 61 Providing and supplying Air Valves as per IS 14845-2000 and MJP’s standard specifications of approved make and quality of following diameters including railway freight, inspection charges, unloading from railway wagons, loading into truck, transportation upto departmental stores, unloding and stacking excluding GST levied by GOI & GOM in all respect etc. complete. (Make : Leader) 62 Lowering, laying and fixing in proper alignment and position all types of C.I. air valves as directed by Engineer-in-charge including cost of conveyance from stores to site of work, cost of all material and giving satisfactory hydraulic testing, etc. complete. (for all class of valves). (Make : Leader)
